RESUMO
The development of an efficient, low-cost and earth-abundant electrocatalyst for water splitting is crucial for the production of sustainable hydrogen energy. However their practical applications are largely restricted by their limited synthesis methods, large overpotential and low surface area. Hierarchical materials with a highly porous three-dimensional nanostructure have garnered significant attention due to their exceptional electrocatalytic properties. These hierarchical porous frameworks enable the fast electron transfer, rapid mass transport, and high density of unsaturated metal sites and maximize product selectivity. Here the process involved obtaining monodispersed microrod-shaped Ni(OH)2 through a hydrothermal reaction, followed by a heat treatment to convert it into hierarchical microrod-shaped NiO materials. N2 sorption analysis revealed that the BET surface area increased from 9 to 89 m2/g as a result of the heat treatment. The hierarchical microrod-shaped NiO materials demonstrated outstanding bifunctional electrocatalytic water splitting capabilities, excelling in both HER and OER in basic solution. Overpotential of 347 mV is achieved at 10 mA/cm2 for OER activity, with a Tafel slope of 77 mV/dec. Similarly, overpotential of 488 mV is achieved at 10 mA/cm2 for HER activity, with a Tafel slope of 62 mV/dec.
RESUMO
To address issues of global energy sustainability, it is essential to develop highly efficient bifunctional transition metal-based electrocatalysts to accelerate the kinetics of both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER). Herein, the heterogeneous molybdenum and vanadium codoped cobalt carbonate nanosheets loaded on nickel foam (VMoCoCOx@NF) are fabricated by facile hydrothermal deposition. Firstly, the mole ratio of V/Mo/Co in the composite is optimized by response surface methodology (RSM). When the optimized composite serves as a bifunctional catalyst, the water-splitting current density achieves 10 mA cm-2 and 100 mA cm-2 at cell voltages of 1.54 V and 1.61 V in a 1.0 M KOH electrolyte with robust stability. Furthermore, characterization is carried out using field emission scanning electron microscopy-energy dispersive spectroscopy (FESEM-EDS), high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Density functional theory (DFT) calculations reveal that the fabricated VMoCoCOx@NF catalyst synergistically decreases the Gibbs free energy of hydrogen and oxygen-containing intermediates, thus accelerating OER/HER catalytic kinetics. Benefiting from the concerted advantages of porous NF substrates and clustered VMoCoCOx nanosheets, the fabricated catalyst exhibits superior electrocatalytic performance. This work presents a novel approach to developing transition metal catalysts for overall water splitting.
RESUMO
It is a challenging task to design and synthesize stable, and high-performance non-precious metals bifunctional catalysts for water-splitting. Herein, the coupling between Se vacancy and interface engineering is highlighted to synthesize a unique CoFeSe hollow nanocubes structure on MXene-modified nickel foam (NF) by in-situ phase transition from bifunctionality prussian blue analogue (PBA) derivatives (VSe-CoFeSe@MXene/NF). DFT theory reveals that the Se vacancy and interface engineering modulate the surface electronic structure and optimize the surface adsorption energy of the intermediates. Experimental data also confirm that the as-prepared CoFeSe@MF catalyst exhibits advanced electrocatalytic properties, 283 mV (OER) and 67 mV (HER) are required to drive the current density of 10 mA cm-2. Notably, it is assembled into a two-electrode system for integral water decomposition, which only requires a low cell potential of 1.57 V at current of 10 mA cm-2, together with excellent durability for 48 h. The strategy is expected to provide a new direction for the design and construction of highly efficient collaborative integrated water decomposition electrocatalysts.
RESUMO
This work illustrates the practicality and economic benefits of employing a hetero-interfaced electrocatalyst (CoS2@CoFe-LDH), containing cobalt sulphide and iron-cobalt double-layer hydroxide for large-scale hydrogen generation. Here, the rational synthesis and detailed characterization of the CoS2@CoFe-LDH material to unravel its unique heterostructure are essayed. The CoS2@CoFe-LDH operates as a bifunctional electrocatalyst to trigger both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) in alkaline seawater (pH 14.0) while showcasing low overpotential requirement for HER (311 mV) and OER (450 mV) at 100 mA cm- 2 current density. The identical CoS2@CoFe-LDH on either electrode in an H-cell setup results in simultaneous H2 and O2 production from seawater with a ≈98% Faradaic efficiency with an applied potential of 1.96V@100 mA cm- 2. Next, this CoS2@CoFe-LDH catalyst is deployed on both sides of a membrane electrode assembly in a one-stack electrolyzer, which retains the intrinsic bifunctional reactivity of the catalyst to generate H2 and O2 in tandem from alkaline seawater with an impeccable energy efficiency (50 kWh kg-1-of-H2). This electrolyzer assembly can be directly linked with a Si-solar cell to produce truly green hydrogen with a solar-to-hydrogen generation efficiency of 15.88%, highlighting the potential of this converting seawater to hydrogen under solar irradiation.
RESUMO
The utilization of seawater for hydrogen production via water splitting is increasingly recognized as a promising avenue for the future. The key dilemma for seawater electrolysis is the incompatibility of superior hydrogen- and oxygen-evolving activities at ampere-scale current densities for both cathodic and anodic catalysts, thus leading to large electric power consumption of overall seawater splitting. Here, in situ construction of Fe4N/Co3N/MoO2 heterostructure arrays anchoring on metallic nickel nitride surface with multilevel collaborative catalytic interfaces and abundant multifunctional metal sites is reported, which serves as a robust bifunctional catalyst for alkaline freshwater/seawater splitting at ampere-level current density. Operando Raman and X-ray photoelectron spectroscopic studies combined with density functional theory calculations corroborate that Mo and Co/Fe sites situated on the Fe4N/Co3N/MoO2 multilevel interfaces optimize the reaction pathway and coordination environment to enhance water adsorption/dissociation, hydrogen adsorption, and oxygen-containing intermediate adsorption, thus cooperatively expediting hydrogen/oxygen evolution reactions in base. Inspiringly, this electrocatalyst can substantially ameliorate overall freshwater/seawater splitting at 1000 mA cm-2 with low cell voltages of 1.65/1.69 V, along with superb long-term stability at 500-1500 mA cm-2 for over 200 h, outperforming nearly all the ever-reported non-noble electrocatalysts for freshwater/seawater electrolysis. This work offers a viable approach to design high-performance bifunctional catalysts for seawater splitting.
RESUMO
The advancement in electrocatalysis, particularly in the development of efficient catalysts for hydrogen and oxygen evolution reactions (HER and OER), is crucial for sustainable energy generation through processes like overall water splitting. A notable bifunctional electrocatalyst, CoFe2O4/Co7Fe3, has been engineered to facilitate both OER and HER concurrently, aiming to reduce overpotentials. In the pursuit of further enhancing catalytic efficiency, a morphological transformation has been achieved by introducing a sulphur source and multi-walled carbon nanotubes (MWCNTs) into the catalyst system, resulting in S-CoFe2O4/Co7Fe3/MWCNTs. This modification has significantly improved the activity for both OER and HER. An onset overpotential of 250 mV@10 mAcm-2 for the OER and 270 mV@50 mAcm-2 for the HER, indicating efficient catalytic activity at relatively low overpotentials. S-CoFe2O4/Co7Fe3/MWCNTs display an outstanding long-term stability in alkaline electrolytes, with minimal Tafel slopes of 77 mV/dec for the OER and 70 mV/dec for the HER, suggesting sustained catalytic performance over extended periods. Furthermore, when employed as both the cathode and anode in the context of complete water splitting, S-CoFe2O4/Co7Fe3/MWCNTs demonstrate an impressive cell voltage of 1.52 V at a current density of 10 mA cm-2 in a 1 M KOH solution, showcasing its viability for practical applications. Given its cost-effectiveness and superior activity, S-CoFe2O4/Co7Fe3/MWCNTs hold significant promise for widespread applications in overall water splitting electrocatalysis, contributing to the advancement of cleaner and sustainable fuel generation technologies.
RESUMO
This review covers recent progress on transition metal dichalcogenides (TMDs) as bifunctional electrocatalysts for Zinc-air batteries (ZABs), emphasizing their suitable surface area, electrocatalytic active sites, stability in acidic/basic environments, and tunable electronic properties. It discusses strategies like defect engineering, doping, interface, and structural modifications of TMDs nanostructures for enhancing the performances of ZABs. Zinc-air batteries are promising energy storage devices owing to their high energy density, low cost, and environmental friendliness. However, the development of durable and efficient bifunctional electrocatalysts is a major concern for Zn-air batteries. In this review, we summarize the recent progress on transition metal dichalcogenides (TMDs) as bifunctional electrocatalysts for Zn-air batteries. We discuss the advantages of TMDs, such as high activity, good stability, and tunable electronic structure, as well as the challenges, such as low conductivity, poor durability, and limited active sites. We also highlight the strategies for fine-tuning the properties of TMDs, such as defect engineering, doping, hybridization, and structural engineering, to enhance their catalytic performance and stability. We provide a comprehensive and in-depth analysis of the applications of TMDs in Zn-air batteries, demonstrating their potential as low-cost, abundant, and environmentally friendly alternatives to noble metal catalysts. We also suggest future directions like exploring new TMDs materials and compositions, developing novel synthesis and modification techniques, investigating the interfacial interactions and charge transfer processes, and integrating TMDs with other functional materials. This review aims to illuminate the path forward for the development of efficient and durable Zn-air batteries, aligning with the broader objectives of sustainable energy solutions.
RESUMO
Water electrolysis assisted by hydrazine has emerged as a prospective energy conversion method for achieving efficient hydrogen generation. Due to the potential coincidence region (PCR) between the hydrogen evolution reaction (HER) and the electro-oxidation of hydrazine, the hydrazine oxidation reaction (HzOR) offers distinct advantages in terms of strategy amalgamation, device architecture, and the broadening of application horizons. Herein, we report a bifunctional electrocatalyst of interfacial heterogeneous Fe2P/Co2P microspheres supported on Ni foam (FeCoP/NF). Benefiting from the strong interfacial coupling effect between Fe2P and Co2P and the three-dimensional microsphere structure, FeCoP/NF exhibits outstanding bifunctional electrocatalytic performance, achieving 10 mA cm-2 with low overpotentials of 10 and 203 mV for HER and HzOR, respectively. Utilizing FeCoP/NF for both electrodes in HzOR-assisted water electrolysis results in significantly reduced potentials of 820 mV for 1 A cm-2 in contrast to the electro-oxidation of alternative chemical substrates. The presence of a potential coincidence region makes the application of self-activated seawater electrolysis realistic. The gas production behavior at different current densities in this interesting hydrogen production system is discussed, and some rules that are distinguished from conventional water electrolysis are summarized. Furthermore, a new self-powered hydrogen production system with a direct hydrazine fuel cell, rechargeable Zn-hydrazine battery, and hydrazine-assisted seawater electrolysis is proposed, emphasizing the distinct benefits of HzOR and its potential role in electrochemical energy conversion technologies powered by renewable sources.
RESUMO
It is critical and challenging to develop highly active and low cost bifunctional electrocatalysts for the hydrogen/oxygen evolution reaction (HER/OER) in water electrolysis. Herein, we propose cerium-vanadium-based hollow nanopillar arrays supported on nickel foam (CeV-HNA/NF) as bifunctional HER/OER electrocatalysts, which are prepared by etching the V metal-organic framework with Ce salt and then pyrolyzing. Etching results in multidimensional optimizations of electrocatalysts, covering substantial oxygen vacancies, optimized electronic configurations, and an open-type structure of hollow nanopillar arrays, which contribute to accelerating the charge transfer rate, regulating the adsorption energy of H/O-containing reaction intermediates, and fully exposing the active sites. The reconstruction of the electrocatalyst is also accelerated by Ce doping, which results in highly active hydroxy vanadium oxide interfaces. Therefore, extremely low overpotentials of 170 and 240 mV under a current density of 100 mA cm-2 are achieved for the HER and OER under alkaline conditions, respectively, with long-term stability for 300 h. An electrolysis cell with CeV-HNA/NF as both the cathode and anode delivers a small voltage of 1.53 V to achieve water electrolysis under 10 mA cm-2, accompanied by superior durability for 150 h. This design provides an innovative way to develop advanced bifunctional electrocatalysts for overall water electrolysis.
RESUMO
Confronted with the pressing issue of energy scarcity, the development of an economical and potent bifunctional catalyst is of paramount importance. We adopt an interface engineering strategy to modify the surface of NiFe-LDH nanoplates with O2 plasma treatment. This process enhances the local electric field of NiFe-LDH, resulting in the formation of a self-assembled polycrystalline nanowire array on the nanoplate surface. After O2 plasma treatment for 30â min, the NiFe-LDH-P30 not only formed a heterostructure with rough surface, but also regulated the exposure of crystal surfaces. Due to the strong interface coupling between the self-assembled 3D nanoflowers, 2D nanoplates and 1D nanowires, the NiFe-LDH-P30 exhibits an excellent structural stability. Moreover, it demonstrated exceptional HER and OER activities in alkaline condition, achieving a low overpotentials of 154â mV and 242â mV at 10â mA cm-2, respectively. Furthermore, NiFe-LDH-P30 as the dual-electrode material for the cathode and anode in the process of water splitting results in a low voltage of 1.63â V at a current density of 10â mA cm-2. Through the strategic application of interface engineering, this work has pioneered a novel approach to the creation of transition metal-based electrocatalysts, which is benefit to a range of practical energy applications.
RESUMO
Oxygen reduction reaction (ORR) and oxygen evolutionc reaction (OER) are important chemical reactions for a rechargeable lithium-oxygen battery (LOB). Recently, high-entropy alloys and oxides have attracted much attention because they showed good electrocatalytic performance for oxygen evolution reaction (OER) and/or oxygen reduction reaction (ORR). In this study, we aimed to synthesize and characterize CoSn(OH)6 and two types of high-entropy perovskite hydroxides, that is, (Co0.2Cu0.2Fe0.2Mn0.2Mg0.2)Sn(OH)6 (CCFMMSOH) and (Co0.2Cu0.2Fe0.2Mn0.2Ni0.2)Sn(OH)6 (CCFMNSOH). TEM observation and XRD measurements revealed that the high-entropy hydroxides CCFMMSOH and CCFMNSOH had cubic crystals with sides of approximately 150-200 nm and crystal structures similar to those of perovskite-type CSOH. LSV measurement results showed that the high-entropy hydroxides CCFMMSOH and CCFMNSOH showed bifunctional catalytic functions for the ORR and OER. CCFMNSOH showed better catalytic performance than CCFMMSOH.
RESUMO
Developing cost-effective, durable bifunctional electrocatalysts is crucial but remains challenging due to slow hydrogen/oxygen evolution reaction (HER/OER) kinetics in water electrolysis. Herein, a combined engineering strategy of phosphorous vacancy (Vp) and spontaneous built-in electric field (BIEF) is proposed to design novel highly-conductive Co-doped MoP@MXene heterostructures with phosphorous vacancy (Vp-Co-MoP@MXene). Wherein, Co doping regulates the surface electronic structure and charge re-distribution of MoP, Vp induces more defects and active sites, while BIEF accelerates the interfacial charge transfer rate between Vp-Co-MoP and MXene. Therefore, the synergistic integration of Vp-Co-MoP/MXene efficiently decreases activation energy and kinetic barrier, thus promoting its intrinsically catalytic activity and structural stability. Consequently, the Vp-Co-MoP@MXene catalyst displays low overpotentials of 102.3/196.5 and 265.0/320.0 mV at 10/50 mA cm-2 for HER and OER, respectively. Notably, two-electrode electrolyzers with the Vp-Co-MoP@MXene bifunctional catalysts to achieve 10/50 mA cm-2, only need low-cell voltages of 1.57/1.64 V in alkaline media. Besides, experimental and theoretical results confirm that the hetero-structure effectively reduces hydrogen adsorption free energy and rate-determining-step energy barrier of OER intermediates, thereby greatly boosting its intrinsically catalytic activity. This work verifies an effective strategy to fabricate efficient non-precious bifunctional electro-catalysts for water splitting via combination engineering of phosphorous vacancy, cation doping, and BIEF.
RESUMO
Developing a non-noble metal-based bifunctional electrocatalyst with high efficiency and stability for overall water splitting is desirable for renewable energy systems. We developed a novel method to fabricate a heterostructured electrocatalyst, comprising a NiCoP nanoneedle array grown on Ti3C2Tx MXene-coated Ni foam (NCP-MX/NF) using a dip-coating hydrothermal method, followed by phosphorization. Due to the abundance of active sites, enhanced electronic kinetics, and sufficient electrolyte accessibility resulting from the synergistic effects of NCP and MXene, NCP-MX/NF bifunctional alkaline catalysts afford superb electrocatalytic performance, with a low overpotential (72 mV at 10 mA cm-2 for HER and 303 mV at 50 mA cm-2 for OER), a low Tafel slope (49.2 mV dec-1 for HER and 69.5 mV dec-1 for OER), and long-term stability. Moreover, the overall water splitting performance of NCP-MX/NF, which requires potentials as low as 1.54 and 1.76 V at a current density of 10 and 50 mA cm-2, respectively, exceeded the performance of the Pt/Câ¥IrO2 couple in terms of overall water splitting. Density functional theory (DFT) calculations for the NCP/Ti3C2O2 interface model predicted the catalytic contribution to interfacial formation by analyzing the electronic redistribution at the interface. This contribution was also evaluated by calculating the adsorption energetics of the descriptor molecules (H2O and the H and OER intermediates).
RESUMO
Manufacturing high-performance and cost-affordable non-metallic, electroactive 1D carbon material for energy storage and hydrogen evolution reaction (HER) is of foremost importance to respond positively to the impending energy crisis. Porous N-doped carbon nanofiber (PNCNF) is successfully synthesized by electrospinning, using selenium nanoparticles as a sacrificial template (where Se is reutilized for ZIF-67 selenization as a bi-process, and the surface of PNCNF is modified with poly(3,4-ethylenedioxythiophene) (PNCNT/PEDOT) by electropolymerization. The prepared materials are found ideal for energy storage (supercapacitor) and electrocatalysis (HER). The bi-functional material has shown excellent energy storage capability with the specific capacitance (CS) of 230 F g-1 (PNCNF) and 395 F g-1 (PNCNF/PEDOT), and the symmetric supercapacitor device, PNCNF/PEDOT//PEDOT/PNCNF, exhibits 32.4 Wh kg-1 energy density at 14400 W kg-1 power density with 96.6% Coulombic efficiency and 106% CS at the end of 5000 charge-discharge cycles. The rate capability of the symmetric supercapacitor cell of PNCNF/PEDOT is 51% for the current density increase from 1 to 8 A g-1, while that of PNCNF is a meager 29% only. Electrocatalytic HER at the PNCNF electrode is achieved with an overpotential of 281 mV@10 mA cm-2 relative to the Pt/C electrode and a low Tafel slop value of 96 mV dec-1.
RESUMO
In response to the growing demand for clean, green, and sustainable energy sources, the development of cost-effective and durable high-activity overall water splitting electrocatalysts is urgently needed. In this study, the heterogeneous structure formed by the combination of FeCoNiP and FeNi-LDH was homogeneously dispersed onto CuO nanowires generated by in-situ oxidation of copper foam as a substrate using an electrodeposition method. This multilevel structure exhibits excellent bifunctional properties as an electrode material in alkaline solutions, for the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER) only 206 mV and 147 mV overpotentials are needed to achieve a current density of 100 mA cm-2 respectively. Full water electrolysis is thus enabled to take place at such a low cell voltage as 1.64 V to reach the current density of 100 mA cm-2, which exhibits a long-term stability of 30 h. These improved electrocatalytic performances stem from the construction of multilevel structures. The X-ray photoelectron spectroscopy suggests that strong electron transfer occurs between heterogeneous structures, thus facilitating the OER and HER process. The dispersion of CuO nanowires not only increases the electrochemically active surface areas but also improves the overall hydrophilic and aerophobic properties. This work highlights the positive effect of multilevel structure in the design of more efficient electrocatalysts and provides a reference for the preparation of other low-cost, high-activity bifunctional electrocatalysts.
RESUMO
The rational design of efficient and economical bifunctional electrocatalysts remained a challenge for overall water electrolysis. In this work, the Ni-boride/ phosphide particles anchored amorphous B-doped carbon layer with hierarchical porous characteristics in Ni foam (Ni3P/Ni3B/B-C/NF) was fabricated for overall water splitting. The Boroncarbide (B4C) power was filled and fixed in the NF interspace through the electroplating and electroless plating, and then annealed in vacuum high temperature. The amorphous B-C layer derived from the B4â C not only speeded up the electron transport, but also cooperate with Ni-boride/phosphide to enhance the electrocatalytic activity for HER and OER synergistically. Furthermore, the hierarchical porous architecture of Ni3P/Ni3B/B-C/NF increased space utilization to load more active materials. The self-supported Ni3P/Ni3B/B-C/NF electrode possessed a low overpotential of 212 and 280â mV to deliver 100â mA cm-2 for HER and OER, respectively, and high stability for 48â h. In particular, the electrolyzer constituted with the Ni3P/Ni3B/B-C/NF bifunctional electrocatalyst only required a voltage of 1.59â V at 50â mA cm-2 for water electrocatalysis under alkaline medium, and demonstrated long-term stability for 48â h. This study provides a new technical path for the development of bifunctional of transition metal borides to promote the application of hydrogen production from water splitting.
RESUMO
Engineering the intermetallic nanostructures as an effective bifunctional electrocatalyst for hydrogen and oxygen evolution reactions (HER and OER) is of great interest in green hydrogen production. However, a few non-noble metals act as bifunctional electrocatalysts, exhibiting terrific HER and OER processes reported to date. Herein the intermetallic nickel-antimonide (NiâSb) dendritic nanostructure via cost-effective electro-co-deposition method is designed and their bifunctional electrocatalytic property toward HER and OER is unrevealed. The designed NiâSb delivers a superior bifunctional activity in 1 m KOH electrolyte, with a shallow overpotential of ≈119 mV at -10 mA for HER and ≈200 mV at 50 mA for OER. The mechanism behind the excellent bifunctional property of NiâSb is discussed via "interfacial descriptor" with the aid of Kelvin probe force microscopy (KPFM). This study reveals the rate of electrocatalytic reaction depends on the energy required for electron and proton transfer from the catalyst's surface. It is noteworthy that the assembled NiâSb-90 electrolyzer requires only a minuscule cell voltage of ≈1.46 V for water splitting, which is far superior to the art of commercial catalysts.
RESUMO
Construction of multi-component heterostructures is an effective strategy for electrocatalysts to improve both the hydrogen evolution reaction (HER) at the cathode and the oxygen evolution reaction (OER) activity at the anode. Herein, an efficient bifunctional electrocatalyst towards overall water/seawater splitting (OW/SS) is reported with strategy of heterostructure construction (ruthenium/nickel phosphorus) on nickel hydroxide (Ni(OH)2). With the unique hydrolysis layer (Ni(OH)2), the processes of H2O hydrolysis and the adsorption/desorption of H*/O-containing intermediates (OH, O, OOH) were greatly boosted by Ru and P sites, which acted as the catalytic active centers of OER and HER, respectively. In addition, the electronic structure reconfiguration was realized through the strong interaction between multi-interfaces. For alkaline HER at the current density of 10 mA cm-2, the overpotential of Ru-P-Ni(OH)2/NF (denoted as RNPOH/NF) was 98 mV, whereas just 230 mV of overpotential was essential to stimulate alkaline OER at the current density of 20 mA cm-2. Specifically, as a bifunctional electrocatalyst towards overall water splitting, RNPOH/NF deserves cell voltages of 1.7/1.92 V and 1.75/1.94 V, respectively, to activate current densities of 50/100 mA cm-2 in alkaline water/seawater systems, together with a good durability of 12 h. This work contributes insights to the development of bifunctional electrocatalysts for overall water/seawater splitting.
RESUMO
The rational design of morphology and heterogeneous interfaces for non-precious metal electrocatalysts is crucial in electrochemical water decomposition. In this paper, a bifunctional electrocatalyst (Ni/NiFe LDH), which coupling nickel with nickel-iron layer double hydroxide (NiFe LDH), is synthesized on carbon cloth. At current density of 10 mA cm-2, the Ni/NiFe LDH exhibits a low hydrogen evolution reaction (HER) overpotential of only 36 mV due to the accelerated electrolyte penetration, which is caused by superhydrophilic interface. Moreover, an alkaline electrolyzer is formed and provide a current density of 10 mA cm-2 with a voltage of only 1.49 V. It is confirmed by the density functional theory (DFT) that electron from the Ni layer is transferred to NiFe LDH layer, redistributing the local electron density around the heterogeneous phase interface. Thus, the Gibbs free energy for hydrogen adsorption is optimized. This work provides a promising strategy for the rational regulation of electrons at heterogeneous interfaces and the synthesis of flexible electrocatalysts.
RESUMO
Constructing heterostructured electrocatalysts has proven effective in enhancing intrinsic catalytic activity. Herein, under guidance of theoretical calculations, hierarchical porous quasi-hexagonal Co2P nanosheets/Co heterostructures supported on carbon cloth (Co2P/Co/CC) with a high surface area were rationally designed and elaborately constructed through electroless Co plating, electrochemical oxidation, and phosphidation process, which showed significant electrocatalytic performance toward water electrolysis. Specifically, theoretical calculations revealed that the Co2P/Co heterostructure adjusted the electronic structure of Co2P and Co, reducing the energy barrier for target reactions and thereby boosting electrocatalytic activities for the hydrogen evolution reaction (HER). Notably, the typical Co2P/Co/CC catalyst demonstrated impressive HER performance, with low overpotentials of only 52 and 48 mV to achieve a current density of 10 mA/cm2 in 0.5 M H2SO4 and 1.0 M KOH solutions, respectively. The remarkable electrocatalytic performance of the catalyst can be attributed to the improved intrinsic activity resulting from the Co2P/Co heterostructures and the highly exposed active sites provided by the hierarchical porous structures. Furthermore, the Co2P/Co/CC catalyst exhibited excellent oxygen evolution reaction (OER) performance in alkaline electrolyte, requiring a low overpotential of only 306 mV to achieve a current density of 100 mA/cm2. Additionally, a two-electrode electrolyzer assembled with the Co2P/Co/CC electrodes achieved a current density of 10 mA/cm2 at a low cell voltage of 1.54 V and demonstrated excellent long-term stability. This work presents a novel and feasible strategy for constructing hierarchical heterostructured electrocatalysts that enable efficient water electrolysis. By combining rational design and theoretical guidance, our approach offers promising prospects for advancing the field of electrocatalysis and facilitating sustainable energy conversion.