The Effect of Multi-Step Tempering and Partition Heat Treatment on 25Cr2Ni3MoV Steel's Cryogenic Strength Properties.

In this study, the refinement of two microstructures was controlled in medium carbon 25Cr2Ni3MoV steel via multi-step tempering and partition (MTP) to achieve high cryogenic strength-ductility combinations. Microstructure evolution, the distribution of stress concentration, and microcrack formation and propagation during cryogenic Charpy impact testing were investigated. Compared with their performance in the quenching and tempering states (QT), the MTP steels showed a significant improvement in yield strength (1300 MPa), total elongation (25%), and impact toughness (>25 J) at liquid nitrogen temperature (LNT). The strengthening contributions mainly originated from the high dislocation density and refinement cementite (size: 70 nm) in the martensite lath (width: 1.5 µm) introduced by refined reversed austenite and its latter decomposition. The instrumented Charpy impact results indicated that cracks nucleated in the primary austenite grain (PAG) boundary for two steels due to the strain concentration band preferring to appear near PAGs, while cracks in the QT and MTP samples propagated along the PAGs and high-angle grain boundary (HAGB), respectively. The crystallized plasticity finite element simulation revealed that the PAG boundary with cementite precipitates of large size (>200 nm) was less able to dissipate crack propagation energy than the HAGBs by continuously forming a high strain concentration area, thus leading to the low-impact toughness of the QT steel.

Evolutions of Cube ({001}<100>) and {115}<161> Orientations in Cold-Rolled Ultra-Thin Non-Oriented Silicon Steel.

In this study, the evolutions of Cube and {115}<161> orientations of a cold-rolled ultra-thin non-oriented silicon steel were investigated using a combination of experimental investigation and the crystal plasticity finite element method (CPFEM). The results show that Cube orientations remain relatively stable when their initial deviation angles from the ideal Cube orientation are less than 12°, even after a 60% cold rolling reduction. However, larger deviations occur due to higher strain near grain boundaries. Furthermore, the {115}<161> orientations, with an initial deviation of ~18° from the ideal Cube orientation, become separated into different orientation regions during cold rolling. Some regions gradually approach the ideal Cube orientation as cold rolling progresses and reach ~12.5° deviation from the ideal Cube at a 40% reduction. This study demonstrates good agreement between simulation and experimental results, highlights the micro-deformation mechanisms during rolling, and offers insights for optimizing the ultra-thin strip rolling process.

Inverse Identification of Single-Crystal Plasticity Parameters of HCP Zinc from Nanoindentation Curves and Residual Topographies.

This paper investigates the orientation-dependent characteristics of pure zinc under localized loading using nanoindentation experiments and crystal plasticity finite element (CPFEM) simulations. Nanoindentation experiments on different grain orientations exhibited distinct load-depth responses. Atomic force microscopy revealed two-fold unsymmetrical material pile-up patterns. Obtaining crystal plasticity model parameters usually requires time-consuming micromechanical tests. Inverse analysis using experimental and simulated loading-unloading nanoindentation curves of individual grains is commonly used, however the solution to the inverse identification problem is not necessarily unique. In this study, an approach is presented allowing the identification of CPFEM constitutive parameters from nanoindentation curves and residual topographies. The proposed approach combines the response surface methodology together with a genetic algorithm to determine an optimal set of parameters. The CPFEM simulations corroborate with measured nanoindentation curves and residual profiles and reveal the evolution of deformation activity underneath the indenter.

Texture evolution and mechanical behaviour of irradiated face-centred cubic metals.

A physically based theoretical model is proposed to investigate the mechanical behaviour and crystallographic texture evolution of irradiated face-centred cubic metals. This model is capable of capturing the main features of irradiated polycrystalline materials including irradiation hardening, post-yield softening and plasticity localization. Numerical results show a good agreement with experimental data for both unirradiated and irradiated stress-strain relationships. The study of crystallographic texture reveals that the initial randomly distributed texture of unirradiated metals under tensile loading can evolve into a mixture of [111] and [100] textures. Regarding the irradiated case, crystallographic texture develops in a different way, and an extra part of [110] texture evolves into [100] and [111] textures. Thus, [100] and [111] textures become dominant more quickly compared with those of the unirradiated case for the reason that [100] and [111]-oriented crystals have higher strength, and their plastic deformation behaviours are more active than other oriented crystals. It can be concluded that irradiation-induced defects can affect both the mechanical behaviour and texture evolution of metals, both of which are closely related to irradiation hardening.