Reclamation alters evapotranspiration and its biophysical controls in a meadow grassland on the Mongolian Plateau.

Global grasslands were constantly being replaced and reclaimed for cropland, and such reclamations may profoundly affect ecological such as water cycles. However, the long-term effects of this conversion on evapotranspiration (ET) processes remain underexplored. To discern changes in ET from grassland to reclaimed cropland and among different crop rotations, a four-year study (2018-2021) was conducted using the eddy covariance system in a Hulunber grassland and a neighboring reclaimed cropland. The ET in reclaimed cropland (248 mm) was 49% higher than the grassland (166 mm) during the growing season (crop growth period), whereas the ET in the grassland (134 mm) exceeded that in the cropland (128 mm) by 6% in the non-growing season. The croplands experienced a 19% increase in precipitation, primarily due to artificial irrigation during the growing season. Meanwhile, the increase in ET in reclaimed cropland might also be influenced by changes in vegetation type and crop growth characteristics, as well as by rational tillage practices that increase the cover of vegetation and biomass. Notably, potato cultivation most closely matched the water balance of grasslands. In addition, irrigation directly increased soil water content (SWC), and that enhancing the sensitivity of ET to SWC. Overall, this study highlighted the importance of understanding ET variations due to grassland conversion to cropland and different crop rotations, emphasizing the role of irrigation and tillage practices.

Transfer Efficiency and Organization in Turbulent Transport over Alpine Tundra.

The exchange of momentum, heat and trace gases between atmosphere and surface is mainly controlled by turbulent fluxes. Turbulent mixing is usually parametrized using Monin-Obukhov similarity theory (MOST), which was derived for steady turbulence over homogeneous and flat surfaces, but is nevertheless routinely applied to unsteady turbulence over non-homogeneous surfaces. We study four years of eddy-covariance measurements at a highly heterogeneous alpine valley site in Finse, Norway, to gain insights into the validity of MOST, the turbulent transport mechanisms and the contributing coherent structures. The site exhibits a bimodal topography-following flux footprint, with the two dominant wind sectors characterized by organized and strongly negative momentum flux, but different anisotropy and contributions of submeso-scale motions, leading to a failure of eddy-diffusivity closures and different transfer efficiencies for different scalars. The quadrant analysis of the momentum flux reveals that under stable conditions sweeps transport more momentum than the more frequently occurring ejections, while the opposite is observed under unstable stratification. From quadrant analysis, we derive the ratio of the amount of disorganized to organized structures, that we refer to as organization ratio (OR). We find an invertible relation between transfer efficiency and corresponding organization ratio with an algebraic sigmoid function. The organization ratio further explains the scatter around scaling functions used in MOST and thus indicates that coherent structures modify MOST. Our results highlight the critical role of coherent structures in turbulent transport in heterogeneous tundra environments and may help to find new parametrizations for numerical weather prediction or climate models.

Effects of Yellow Sea Warm Current on zooplankton community composition and functional groups in winter.

The Yellow Sea Warm Current (YSWC) constitutes a significant hydrological feature in the Yellow Sea, particularly prominent during winter, facilitating the transport of warm, saline waters and warm-water species from the open sea to the Bohai and Yellow Seas. The YSWC induces alterations in the community structure and function of zooplankton. However, the effects of the YSWC on the functional trait compositions and functional groups of zooplankton remain unclear. This study aimed to elucidate the influence of the YSWC on the community structure, functional trait composition, and functional groups of zooplankton during winter of 2016. The YSWC significantly impacted the zooplankton assemblage in the central Yellow Sea (CYSA), resulting in notable distinctions from the Shandong coastal assemblage (SCA) and Jiangsu coastal assemblage (JCA). Compared to the SCA and JCA (comprising 45 and 34 taxa, with abundances of 119.4 ± 114.6 ind·m-3 and 82.8 ± 62.1 ind·m-3, respectively), the CYSA exhibited higher species richness and abundance (with 51 taxa and 144.4 ± 103.4 ind·m-3, respectively). This study documented a total of 11 warm-water species, showing a decreasing trend in both species richness and abundance from south to north. The CYSA was characterized by the predominance of medium‒sized, current‒feeding, omnivorous‒herbivorous broadcast spawners, whereas the SCA and the JCA were predominantly dominated by giant‒sized, ambush‒feeding carnivores. The Qingdao-Shidao anticyclonic eddy in the southern of Shandong Province led to a significant increase in the abundance of zooplankton, potentially impacting Yellow Sea fishery resource. This research contributed to a deeper understanding of how YSWC influence the zooplankton community and offered fresh insights into the effects of YSWC on zooplankton function traits and functional groups.

Effects of cross-sectional shapes and arrangement patterns on windbreak effects of shelterbelts by large eddy simulation.

Investigating the wind speed flow field and aerodynamic characteristics of shelterbelts with different structural features is of significant importance for the rational arrangement of shelterbelts and the mitigation of wind-blown sand disasters. Considering five cross-sectional shapes of shelterbelts (rectangle, windward right-angle triangle, leeward right-angle triangle, isosceles triangle, and parabolic) and four layout forms (single shelterbelt, L-shaped network, U-shaped network, and rectangular network), we conducted computational fluid dynamics (CFD) simulations using the large eddy simulation (LES) turbulence model to understand mean wind speed flow field and turbulence structure of shelterbelts with different structural features, and investigated the effects of shelterbelt cross-sectional shapes and layout forms on windbreak indicators, such as protection distance and area. We considered tree canopies as porous media and conducted simulation with the 'Tsujimatsu' shelterbelt in Japan with a total height (H) of 7 m, canopy height of 5.8 m, and a canopy base width of 2 m. The results showed that the average relative errors of mean wind speed and turbulent kinetic energy at different heights obtained by numerical simulations and field measurement were small, being 5.5% and 12%, respectively, indicating that the porous medium canopy model successfully reproduced the mean wind speed and turbulent kinetic energy in the leeward area of the shelterbelt. The rectangular cross-section shelterbelt, with the largest canopy volume, significantly obstructed airflow. The mean wind speed and turbulent kinetic energy showed a notable reduction in the leeward area near the shelterbelt, especially in the upper region (z≥0.5H, where z denoted the height), showing the largest protection range. The parabolic cross-section shelterbelt ranked second in terms of protection range, followed by shelterbelts with windward right-angle, leeward right-angle, and isosceles triangular cross-sections. In the downstream area where horizontal distance x≥10H, the mean wind speed and turbulent kinetic energy of shelterbelts with different cross-sectional shapes tended to be the same. Comparing the flow field structures of single shelterbelts and L-shaped, U-shaped, and rectangular networks, it revealed that the more shelterbelts oriented perpendicular to the incoming wind speed, the more pronounced the wind speed attenuation behind the canopy, a longer distance would be required for airflow to recover to the incoming wind speed. In contrast, the wind protection effect of shelterbelts paralleled to the wind direction was extremely limited, making the U-shaped and rectangular networks more effective in wind protection than single shelterbelts and L-shaped networks. The findings would provide references for the structural configuration and optimal layout of shelterbelt systems.

Methane fluxes in tidal marshes of the conterminous United States.

Methane (CH4) is a potent greenhouse gas (GHG) with atmospheric concentrations that have nearly tripled since pre-industrial times. Wetlands account for a large share of global CH4 emissions, yet the magnitude and factors controlling CH4 fluxes in tidal wetlands remain uncertain. We synthesized CH4 flux data from 100 chamber and 9 eddy covariance (EC) sites across tidal marshes in the conterminous United States to assess controlling factors and improve predictions of CH4 emissions. This effort included creating an open-source database of chamber-based GHG fluxes (https://doi.org/10.25573/serc.14227085). Annual fluxes across chamber and EC sites averaged 26 ± 53 g CH4 m-2 year-1, with a median of 3.9 g CH4 m-2 year-1, and only 25% of sites exceeding 18 g CH4 m-2 year-1. The highest fluxes were observed at fresh-oligohaline sites with daily maximum temperature normals (MATmax) above 25.6°C. These were followed by frequently inundated low and mid-fresh-oligohaline marshes with MATmax ≤25.6°C, and mesohaline sites with MATmax >19°C. Quantile regressions of paired chamber CH4 flux and porewater biogeochemistry revealed that the 90th percentile of fluxes fell below 5 ± 3 nmol m-2 s-1 at sulfate concentrations >4.7 ± 0.6 mM, porewater salinity >21 ± 2 psu, or surface water salinity >15 ± 3 psu. Across sites, salinity was the dominant predictor of annual CH4 fluxes, while within sites, temperature, gross primary productivity (GPP), and tidal height controlled variability at diel and seasonal scales. At the diel scale, GPP preceded temperature in importance for predicting CH4 flux changes, while the opposite was observed at the seasonal scale. Water levels influenced the timing and pathway of diel CH4 fluxes, with pulsed releases of stored CH4 at low to rising tide. This study provides data and methods to improve tidal marsh CH4 emission estimates, support blue carbon assessments, and refine national and global GHG inventories.

Eddy Currents Probe Design for NDT Applications: A Review.

Eddy current testing (ECT) is a crucial non-destructive testing (NDT) technique extensively used across various industries to detect surface and sub-surface defects in conductive materials. This review explores the latest advancements and methodologies in the design of eddy current probes, emphasizing their application in diverse industrial contexts such as aerospace, automotive, energy, and electronics. It explores the fundamental principles of ECT, examining how eddy currents interact with material defects to provide valuable insights into material integrity. The integration of numerical simulations, particularly through the Finite Element Method (FEM), has emerged as a transformative approach, enabling the precise modeling of electromagnetic interactions and optimizing probe configurations. Innovative probe designs, including multiple coil configurations, have significantly enhanced defect detection capabilities. Despite these advancements, challenges remain, particularly in calibration and sensitivity to environmental conditions. This comprehensive overview highlights the evolving landscape of ECT probe design, aiming to provide researchers and practitioners with a detailed understanding of current trends in this dynamic field.

Hydrogen Embrittlement Detection Technology Using Nondestructive Testing for Realizing a Hydrogen Society.

Crack detection in high-pressure hydrogen gas components, such as pipes, is crucial for ensuring the safety and reliability of hydrogen infrastructure. This study conducts the nondestructive testing of crack propagation in steel piping under cyclic compressive loads in the presence of hydrogen in the material. The specimens were hydrogen-precharged through immersion in a 20 mass% ammonium thiocyanate solution at 40 °C for 72 h. The crack growth rate in hydrogen-precharged specimens was approximately 10 times faster than that in uncharged specimens, with cracks propagating from the inner to outer surfaces of the pipe. The fracture surface morphology differed significantly, with flat surfaces in hydrogen-precharged materials and convex or concave surfaces in uncharged materials. Eddy current and hammering tests revealed differences in the presence of large cracks between the two materials. By contrast, hammering tests revealed differences in the presence of a half size crack between the two materials. These findings highlight the effect of hydrogen precharging on crack propagation in steel piping and underscore the importance of early detection methods.

Characteristics and regulatory mechanisms of net ecosystem CO2 exchange at the water-air interface in coastal aquaculture ponds.

Coastal aquaculture ponds represented a biogeochemical hotspot in the global carbon cycle. However, there was a limited understanding of their dynamics. In this study, the eddy covariance (EC) technique was applied to quantify the net ecosystem CO2 exchange (NEE) over coastal aquaculture ponds in the Liaohe River estuary in northern China during 2020, aiming to investigate and quantify the carbon exchange characteristics of this region. The results showed that (a) a predominant "U" shaped diurnal NEE pattern throughout the year. During the sea cucumber monoculture phase, the ponds exhibited a consistent daytime carbon sink and nighttime carbon source pattern. In contrast, during the shrimp and sea cucumber polyculture phase, the ponds mostly remained in a net carbon sink state. (b) NEE was negatively correlated with photosynthetically active radiation (PAR), air temperature (Tair), and wind speed (WS), while showing a positive correlation with atmospheric pressure (AP). (c) Overall, the entire study area (complex underlying surfaces) functioned as a carbon sink in 2020, with a total net carbon sequestration of 281.533 g C·m-2. This was approximately four times greater than the restored wetlands that naturally formed from decommissioned coastal aquaculture ponds. Adjusting for surface heterogeneity revealed that the complex surfaces led to a 34.28 % underestimation of the aquaculture region's unit area carbon sequestration capacity. This study was crucial for assessing the carbon cycling and sequestration functions of coastal aquaculture pond ecosystems and provided a scientific basis for related ecological restoration projects.

Temporal changes in net ecosystem CO2 exchange and influential factors in an apple orchard in Northeast China.

The apple orchards in Liaoning, one of the four major apple-producing areas in Bohai Bay, Northeast China, play a crucial role in regulating the carbon sink effect. However, there is limited information on the variation in carbon flux and its influential factors in apple orchards in this region. To address this, CO2 flux data were monitored throughout the entire apple growth seasons from April to November in 2017 and 2018 in the apple (Malus pumila Mill. cv Hanfu) orchard in Shenyang, China. The energy closure of the apple orchard was calculated, and variations in net ecosystem exchange (NEE) at different time scales and its response to environmental factors were analyzed. Our results showed that the energy balance ratio of the apple was 0.74 in 2017 and 1.38 in 2018. NEE was generally positive in April and November and negative from May to October, indicating a strong carbon sink throughout the growth season. The daily average NEE ranged from - 0.103 to 0.094 mg m-2 s-1 in 2017 and from - 0.134 to 0.059 mg m-2 s-1 in 2018, with the lowest values observed in June and July. NEE was negatively correlated with net radiation, atmospheric temperature, saturated vapor pressure deficit, and soil temperature. These findings provide valuable insights for predicting carbon flux in orchard ecosystems within the context of global climate change.

Consequences of intense drought on CO2 and CH4 fluxes of the reed ecosystem at Lake Neusiedl.

Reed (Phragmites australis) dominated wetlands are commonly known as strong carbon (C) sinks due to the high productivity of the reed plant and C fixation in the wetland soil. However, little is known about the effects of drought on reed-dominated wetlands and the possibility of Pannonian reed ecosystems being a source of greenhouse gases (GHG). The drought at Lake Neusiedl had a particular impact on the water level, but also had consequences for the reed belt. Therefore, we investigated the drought-influenced C fluxes and their drivers in the reed ecosystem of this subsaline lake over a period of 4.5 years (mid-2018 to 2022). We applied eddy covariance technique to continuously quantify the vertical turbulent GHG exchange between reed belt & atmosphere and used vegetation indices to account for reed growth. Methane emissions decreased by 76% from 9.2 g CH4-C m-2a-1 (2019) to 2.2 g CH4-C m-2 a-1 (2022), which can be explained by the falling water level, the associated drying out of the reed belt and its consequences. Carbon dioxide emissions initially decreased by 85% from 181 g CO2-C m-2 a-1 (2019) to 27 g CO2-C m-2 a-1 (2021), but then increased to twice the 2019 level in 2022 (391 g CO2-C m-2 a-1). Due to the drying reed belt, the reed initially grew into formerly water-covered areas within the reed belt, especially in 2021, leading to higher photosynthesis through 2021. This development stopped and even reversed in 2022 as a consequence of the sharp decrease in sediment water content from about 65 to 32 Vol-% in mid-2022. Overall, drought led to a decoupling of the reed ecosystem from the open lake area and developed the wetland into a strong C source.

Eddy Current-Based Delamination Imaging in CFRP Using Erosion and Thresholding Approaches.

Carbon fiber reinforced plastic (CFRP) is a composite material known for its high strength-to-weight ratio, stiffness, and corrosion and fatigue resistance, making it suitable for its use in structural components. However, CFRP can be subject to various types of damage, such as delamination, matrix cracking, or fiber breakage, requiring nondestructive evaluation to ensure structural integrity. In this context, damage imaging algorithms are important for assessing the condition of this material. This paper presents signal and image processing methods for delamination characterization of thin CFRP plates using eddy current testing (ECT). The measurement system included an inductive ECT probe with three coil elements, which has the characteristic of allowing eddy currents to be induced in the specimen with two different configurations. In this study, the peak amplitude of the induced voltage in the receiver element and the phase shift between the excitation and receiver signals were considered as damage-sensitive features. Using the ECT probe, C-scans were performed in the vicinity of delamination defects of different sizes. The dimensions and shape of the ECT probe were considered by applying the erosion method in the damage imaging process. Different thresholding approaches were also investigated to extract the size of the defective areas. To evaluate the impact of this application, a comparison is made between the results obtained before and after thresholding using histogram analysis. The evaluation of damage imaging for three different delamination sizes is presented for quantitative analysis.

Numerical Investigation on the Influence of Turbine Rotor Parameters on the Eddy Current Sensor for the Dynamic Blade Tip Clearance Measurement.

Eddy current sensors are increasingly being used to measure the dynamic blade tip clearance in turbines due to their robust anti-interference capabilities and non-contact measurement advantages. However, the current research primarily focuses on enhancing the performance of eddy current sensors themselves, with few studies investigating the influence of turbine rotor parameters on the measurements taken by these sensors for dynamic blade tip clearance. Hence, this paper addresses this gap by using COMSOL Multiphysics 6.2 software to establish a finite model with circuit interfaces. Additionally, the model's validity was verified through experiments. This model is used to simulate the voltage output of the sensor and the measurement of dynamic blade tip clearance under various rotor parameters. The results indicate that the length and number of blades, as well as the hub radius, significantly affect the sensor voltage output in comparison to rotation speed. Furthermore, we show that traditional static calibration methods are inadequate for measuring dynamic blade tip clearance using eddy current sensors. Instead, it is demonstrated that incorporating rotor parameters into the calibration of eddy current sensors can enhance the accuracy of dynamic blade tip clearance measurements.

Eddy Current Array for Defect Detection in Finely Grooved Structure Using MSTSA Network.

In this paper, we focus on eddy current array (ECA) technology for defect detection in finely grooved structures of spinning cylinders, which are significantly affected by surface texture interference, lift-off distance, and mechanical dither. Unlike a single eddy current coil, an ECA, which arranges multiple eddy current coils in a specific configuration, offers not only higher accuracy and efficiency for defect detection but also the inherent properties of space and time for signal acquisition. To efficiently detect defects in finely grooved structures, we introduce a spatiotemporal self-attention mechanism to ECA testing, enabling the detection of defects of various sizes. We propose a Multi-scale SpatioTemporal Self-Attention Network for defect detection, called MSTSA-Net. In our framework, Temporal Attention (TA) and Spatial Attention (SA) blocks are incorporated to capture the spatiotemporal features of defects. Depth-wise and point-wise convolutions are utilized to compute channel weights and spatial weights for self-attention, respectively. Multi-scale features of space and time are extracted separately in a pyramid manner and then fused to regress the bounding boxes and confidence levels of defects. Experimental results show that the proposed method significantly outperforms not only traditional image processing methods but also state-of-the-art models, such as YOLOv3-SPP and Faster R-CNN, with fewer parameters and lower FLOPs in terms of Recall and F1 score.

Experimental Investigation on the Effect of Coil Shape on Planar Eddy Current Sensor Characteristic for Blade Tip Clearance.

Given the increasing application of eddy current sensors for measuring turbine tip clearance in aero engines, enhancing the performance of these sensors is essential for improving measurement accuracy. This study investigates the influence of coil shape on the measurement performance of planar eddy current sensors and identifies an optimal coil shape to enhance sensing capabilities. To achieve this, various coil shapes-specifically circular, square, rectangular wave, and triangular wave-were designed and fabricated, featuring different numbers of turns for the experiment at room temperature. By employing a method for calculating coil inductance, the performance of each sensor was evaluated based on key metrics: measurement range, sensitivity, and linearity. Experimental results reveal that the square coil configuration outperforms other shapes in overall measurement performance. Notably, the square coil demonstrated a measurement range of 0 mm to 8 mm, a sensitivity of 0.115685 µH/mm, and an impressive linearity of 98.41% within the range of 0 mm to 2 mm. These findings indicate that the square coil configuration enhances measurement capabilities. The conclusions drawn from this study provide valuable insights for selecting coil shapes and optimizing the performance of planar eddy current sensors, thereby contributing to the advancement of turbine tip clearance measurement techniques in aero engines.

Study on the formation and characteristics of unstable sheet cavitation on hydrofoils.

Hydrofoils, as fundamental components of hydraulic machinery, directly influence the performance of such machinery. This study conducted an analysis of the cavitation characteristics of hydrofoils at a + 4° angle of attack under various cavitation numbers using numerical simulation and experimental research methods. The focus of the research was to explore the phenomenon of unstable sheet cavitation and its causes, as well as to reveal the characteristics of the re-entrant jet. The large eddy simulation method was employed to calculate the cavitation morphology under three different cavitation numbers. The method is highly consistent with the experimental results in simulating the small-scale detachment at the tail of unstable sheet cavitation and the large-scale shedding of cloud cavitation. The study found that the detachment of unstable sheet cavitation is closely related to the re-entrant jet, which exhibits transient and abrupt characteristics during the unstable sheet cavitation phase. Furthermore, by applying FFT processing to the distribution of maximum reverse velocity and the spatiotemporal changes of Ux on characteristic lines, eigenfrequency of the detachment of unstable sheet cavitation were identified. The research results indicate that cavitation mainly show as sheet cavitation when the cavitation closure point does not exceed the zero-slope point. Beyond this point, it transitions to cloud cavitation. This study provides new insights into the cavitation phenomenon of hydrofoils and offers quantitative research on the phenomenon of unstable sheet cavitation.

Magnetic Induction Heating in a Conducting Polymer for Biomedical Applications.

In this study, we investigate the magnetic induction heating induced in a conducting polymer (CP) under alternative magnetic fields (AMFs). Experimental results and numerical simulations have proved that the magneto-thermal conversion of the CP is caused by the induced eddy current, which is related to the shape and intensity of the applied external AMF, and the intrinsic electrical conductivity, macrostructure and microstructure of the CP. By employing various fabrication methods, specific temperature distribution and control of thermal field within conducting polymer films and aerogels could be achieved. To exploit the potential of magnetic induction heating in CP for biomedical applications, we designed a conducting polymer aerogel-based self-adaptive heat patch and demonstrated its AMF-enabled localized heating of skin. In addition to the thermal ablation of tumor cells via magneto-thermal conversion of the CP, the promotion of neuronal differentiation at mild temperature by noninvasive magneto-electrical stimulation has also been demonstrated to be an effective strategy for tissue engineering.

Eddy covariance measurements reveal a decreased carbon sequestration strength 2010-2022 in an African semiarid savanna.

Monitoring the changes of ecosystem functioning is pivotal for understanding the global carbon cycle. Despite its size and contribution to the global carbon cycle, Africa is largely understudied in regard to ongoing changes of its ecosystem functioning and their responses to climate change. One of the reasons is the lack of long-term in situ data. Here, we use eddy covariance to quantify the net ecosystem exchange (NEE) and its components-gross primary production (GPP) and ecosystem respiration (Reco) for years 2010-2022 for a Sahelian semiarid savanna to study trends in the fluxes. Significant negative trends were found for NEE (12.7 ± 2.8 g C m2 year-1), GPP (39.6 ± 7.9 g C m2 year-1), and Reco (32.2 ± 8.9 g C m2 year-1). We found that NEE decreased by 60% over the study period, and this decrease was mainly caused by stronger negative trends in rainy season GPP than in Reco. Additionally, we observed strong increasing trends in vapor pressure deficit, but no trends in rainfall or soil water content. Thus, a proposed explanation for the decrease in carbon sink strength is increasing atmospheric dryness. The warming climate in the Sahel, coupled with increasing evaporative demand, may thus lead to decreased GPP levels across this biome, and lowering its CO2 sequestration.

Spherical echo-planar time-resolved imaging (sEPTI) for rapid 3D quantitative T 2 * and susceptibility imaging.

PURPOSE: To develop a 3D spherical EPTI (sEPTI) acquisition and a comprehensive reconstruction pipeline for rapid high-quality whole-brain submillimeter T 2 * $$ {\mathrm{T}}_2^{\ast } $$ and QSM quantification. METHODS: For the sEPTI acquisition, spherical k-space coverage is utilized with variable echo-spacing and maximum kx ramp-sampling to improve efficiency and signal incoherency compared to existing EPTI approaches. For reconstruction, an iterative rank-shrinking B0 estimation and odd-even high-order phase correction algorithms were incorporated into the reconstruction to better mitigate artifacts from field imperfections. A physics-informed unrolled network was utilized to boost the SNR, where 1-mm and 0.75-mm isotropic whole-brain imaging were performed in 45 and 90 s at 3 T, respectively. These protocols were validated through simulations, phantom, and in vivo experiments. Ten healthy subjects were recruited to provide sufficient data for the unrolled network. The entire pipeline was validated on additional five healthy subjects where different EPTI sampling approaches were compared. Two additional pediatric patients with epilepsy were recruited to demonstrate the generalizability of the unrolled reconstruction. RESULTS: sEPTI achieved 1.4 × $$ \times $$ faster imaging with improved image quality and quantitative map precision compared to existing EPTI approaches. The B0 update and the phase correction provide improved reconstruction performance with lower artifacts. The unrolled network boosted the SNR, achieving high-quality T 2 * $$ {\mathrm{T}}_2^{\ast } $$ and QSM quantification with single average data. High-quality reconstruction was also obtained in the pediatric patients using this network. CONCLUSION: sEPTI achieved whole-brain distortion-free multi-echo imaging and T 2 * $$ {\mathrm{T}}_2^{\ast } $$ and QSM quantification at 0.75 mm in 90 s which has the potential to be useful for wide clinical applications.

Analytical and computational studies predict negligible risk of cell death from eddy generation off flat surfaces in cell culture flow systems.

Cell-based therapies represent the current frontier of biomedical innovations, with the technologies required underpinning treatments as broad as CAR-T cell therapies, stem cell treatments, genetic therapies and mRNA manufacture. A key bottleneck in the manufacturing process for each of these lies in the expansion of cells within a bioreactor vessel, requiring by far the greatest share of time for what are often time-critical therapies. While various designs, culture feeding and mixing methods are employed in these bioreactors, a common concern among manufacturers and researchers lies in whether shear stresses generated by culture media flow will damage cells and inhibit expansion. This study develops an analytical tool to link macro-scale measures of flow to risk of cell death using relationships with eddy size and dissipation rates, from eddies generated off flat surfaces. This analytical tool was then employed using computational fluid dynamics (CFD) to replicate a range of generic bioreactor geometries and flow conditions. We found that no combination of flow condition or design parameter was predicted by the tool to cause cell death within eddies, indicating negligible risk of cell death due to eddy formation within cell culture systems. While this requires experimental validation, and does not apply when cells are expanded using microcarriers, this tool nonetheless provides reassurance and accessible prediction of bioreactor design parameters that could result in cell death. Finally, our findings show that bioreactor design can be tailored such that the shear stress stimulation of cells can be selectively altered through small changes in flow rate.

Alternating magnetic field guiding system for MNP hyperthermia treatment of deep-seated cancers.

OBJECTIVES: Demonstrate the potential application of a novel, endoscope-like device to guide and focus an alternating magnetic field (AMF) for treating deep-seated cancers via magnetic nanoparticle hyperthermia (MNPH). METHODS: AMF delivery, MNP activation, and eddy current distribution characteristics are investigated through experimental studies in phantoms and computational simulations using a full 3-dimensional human model. The 3D simulations compare the novel device to traditional AMF designs, including a MagForce-like, two-coil system (used clinically) and a single surface-coil system. RESULTS: The results demonstrate that this approach can deliver the same magnetic field strength at the prostate's centroid as traditional AMF designs, while reducing eddy current heating by 2 to 6 times. At the same level of normal tissue heating, this method provides 5.0 times, 1.5 times, and 0.92 times the magnetic field strength to the nearest, centroid, and farthest regions of the prostate, respectively. CONCLUSIONS: These results demonstrate proof-of-concept for an endoscopic magnetic field guiding and focusing system capable of delivering clinically relevant AMF from a distance. This innovative approach offers a promising alternative to conventional field delivery methods by directing AMF through the body, concentrating it in the tumor region, reducing eddy currents in surrounding healthy tissue, and avoiding exposure of nearby metallic implants.