Electrified liquid - liquid interface strategy for sensing lactic acid in buttermilk extract.

Lactic acid (LA) serves as a freshness marker in certain foods. In the present work, electrified interfaces of different nature (i.e., liquid-liquid and liquid-organogel) have been developed for the quantification of LA. Electrochemical sensing of LA at the liquid-organogel interface revealed that adsorptive stripping voltammetry, with a preconcentration time of 500 s offered better sensitivity. Electroanalytical ability of LA under optimized conditions displayed a detection limit of 0.97 µM and 0.71 µM with sensitivity of 2.84 nA µM-1 and 3.59 nA µM-1 for liquid-liquid and liquid-organogel interfaces respectively. Quantification of LA using the developed methodology has been demonstrated in buttermilk as the real matrix. Analysis demonstrate that electrified liquid-liquid and liquid-organogel interfaces are promising approach for sensing LAin buttermilk extract.

Electroanalytical applications of ITIES - A review.

Over the last decades, the interface between two immiscible electrolyte solutions (ITIES) attracted considerable attention of the scientific community due to their vast applications, such as extraction, catalysis, partition studies and sensing. The aim of this Review is to highlight the potential of electrochemistry at the ITIES for analytical purposes, focusing on ITIES-based sensors for detection and quantification of chemically and biologically relevant (bio)molecules. We start by addressing the evolution of ITIES in terms of number of publications over the years along with an overview of their main applications (Chapter 1). Then, we provide a general historical perspective about pioneer voltammetric studies at water/oil systems (Chapter 2). After that, we discuss the most impacting improvements on ITIES sensing systems from both perspectives, set-up design (interface stabilization and miniaturization, selection of the organic solvent, etc.) and optimization of experimental conditions to improve selectivity and sensitivity (Chapter 3). In Chapter 4, we discuss the analytical applications of ITIES for electrochemical sensing of several types of analytes, including drugs, pesticides, proteins, among others. Finally, we highlight the present achievements of ITIES as analytical tool and provide future challenges and perspectives for this technology (Chapter 5).

Phenylethylamine sensing at the electrified liquid-liquid interface. Can electrochemistry be used to follow the UHT milk spoilage process?

This study involved an investigation into the electrochemical characteristic of a few biogenic amines (BAs) occurring at the polarized interface between two immiscible electrolyte solutions (ITIES) with ion transfer voltammetry (ITV). The main focus of this research was the comprehensive electroanalytical and physicochemical analysis of phenylethylamine (PEA), allowing the determined of the formal Galvani potential of the ion transfer reaction (ΔorgaqΦ'), diffusion coefficients (D), formal free Gibbs energy of the ion transfer reaction (ΔG'aq→org) and water-1,2-dichloroethane partition coefficient (logPwater/DCEPEA). Furthermore, the collected data were employed to calculate analytical parameters, including voltametric detection sensitivity, limits of detection and the target analyte quantification. Moreover, the influence of the presence of 7 other BAs (histamine, spermine, spermidine, putrescine, cadaverine, tyramine and tryptamine) on the recorded signals originating from the PEA ion transfer was checked. The feasibility of the developed method was corroborated through experimentation with milk samples. Additionally, utilizing the devised methodology, an electrochemical assessment of the spoilage progression in milk samples was undertaken.

Potential-Modulated Ion Distributions in the Back-to-Back Electrical Double Layers at a Polarised Liquid|Liquid Interface Regulate the Kinetics of Interfacial Electron Transfer.

Biphasic interfacial electron transfer (IET) reactions at polarisable liquid|liquid (L|L) interfaces underpin new approaches to electrosynthesis, redox electrocatalysis, bioelectrochemistry and artificial photosynthesis. Herein, using cyclic and alternating current voltammetry, we demonstrate that under certain experimental conditions, the biphasic 2-electron O2 reduction reaction can proceed by single-step IET between a reductant in the organic phase, decamethylferrocene, and interfacial protons in the presence of O2. Using this biphasic system, we demonstrate that the applied interfacial Galvani potential difference Δ o w φ provides no direct driving force to realise a thermodynamically uphill biphasic IET reaction in the mixed solvent region. We show that the onset potential for a biphasic single-step IET reaction does not correlate with the thermodynamically predicted standard Galvani IET potential and is instead closely correlated with the potential of zero charge at a polarised L|L interface. We outline that the applied Δ o w φ required to modulate the interfacial ion distributions, and thus kinetics of IET, must be optimised to ensure that the aqueous and organic redox species are present in substantial concentrations at the L|L interface simultaneously in order to react.

Nitrazepam and 7-aminonitrazepam studied at the macroscopic and microscopic electrified liquid-liquid interface.

Two benzodiazepine type drugs, that is, nitrazepam and 7-aminonitrazepam, were studied at the electrified liquid-liquid interface (eLLI). Both drugs are illicit and act sedative in the human body and moreover are used as date rape drugs. Existence of the diazepine ring in the concerned chemicals structure and one additional amine group (for 7-aminonitrazepam) allows for the molecular charging below their pKa values, and hence, both drugs can cross the eLLI interface upon application of the appropriate value of the Galvani potential difference. Chosen molecules were studied at the macroscopic eLLI formed in the four electrode cell and microscopic eLLI formed within a microtip defined as the single pore having 25 µm in diameter. Microscopic eLLI was formed using only a few µL of the organic and the aqueous phase with the help of a 3D printed cell. Parameters such as limit of detection and voltammetric detection sensitivity are derived from the experimental data. Developed methodology was used to detect nitrazepam in pharmaceutical formulation and both drugs (nitrazepam and 7-aminonitrazepam) in spiked biological fluids (urine and blood).

Quantized Collision/Fusion Events of Anionic Ionosomes at a Polarized Soft Micro-Interface.

Single-entity collisional electrochemistry (SECE) can capture physicochemical information at the single entity level. In the present work, we systematically studied in-situ generation and detection of single anionic ionosomes via SECE combined with a miniaturized interface between two immiscible electrolyte solutions (ITIES). Ionosome is an ionic-bilayer encapsulated nanoscopic water cluster/droplet that carries a net charge. Discrete spiky ionic currents were observed upon collisions/fusions of individual F- or Cl- -ionosomes with a positively polarized micro-ITIES. This fusion process was proved to follow the bulk electrolysis model. With this method, some essential factors such as concentration and charge density of the hydrated anions, and the interfacial area, were revealed. It demonstrates that anionic ionosomes share a common theoretical framework with their counterparts (i. e., cationic ionosomes, like Li+ -ionosomes). This work will spur the advancements in a myriad of fields, including such as the colloid and interface science, micro- and/or nanoscale electrochemistry, and electrophysiology and brain sciences.

Voltammetric studies of glutathione transfer across arrays of liquid-liquid microinterfaces for sensing applications.

The simple and facilitated transfer of tripeptide glutathione across the water/2-nitrophenyl octhyl ether interface was studied via cyclic voltammetry at interface between two immiscible electrolyte solutions (ITIES). The micro-perforated membrane prepared with a laser with a femtosecond pulse was used for mechanical stabilization of the interface. The method of cyclic voltammetry was used to study the passive and facilitated interfacial transfer of glutathione and its complex with the crown ether dibenzo-18-crown-6 (DB18C6).The glutathione mass transfer mechanism was established and substantiated, the diffusion coefficients, thermodynamic characteristics of interphase transfer and the constant of complexation of the glutathione by DB18C6 were determined. Square wave voltammetry based on facilitated transfer was used for more accurate and sensitive determination of glutathione low detection limit (0.8 µM) with wide linear dynamic range (from 3.0 to 80 µM) was reached. The influence of various potentially interfering ions on the voltammetric determination of glutathione has also been investigated. The method developed was applied to determine glutathione in aqueous solutions and malt extract.

Interfacial Deposition of Titanium Dioxide at the Polarized Liquid-Liquid Interface.

The interfacial polycondensation of titanium dioxide was studied at the bare and fiberglass membrane supported polarized liquid-liquid interface (LLI). Titanium dioxide synthesis was derived from the titanium (IV) tetrabutoxide (initially dissolved in the 1,2-dichloroethane) interfacial hydrolysis followed by its condensation. Experimental parameters, such as the pH of the aqueous phase and the influence of titanium alkoxide concentration in the organic phase on the electrochemical signal and material morphology, were investigated. The latter was achieved with fiberglass membranes used as the LLI support during TiO2 interfacial deposition. Cyclic voltammetry was used for the in situ studies, whereas scanning electron microscopy, energy-dispersive X-ray spectroscopy, and infrared spectroscopy were used during ex situ examination. The interfacial polycondensation reaction could be studied using electrified LLI and resulted in the material being a TiO2 film alone or film decorated with particles.

Voltammetric study of cefotaxime at the macroscopic and miniaturized interface between two immiscible electrolyte solutions.

The electrochemical behavior of cefotaxime (CTX+) was investigated at the polarized macro- and micro-interface between two immiscible electrolyte solutions (ITIES) by cyclic voltammetry and alternating current voltammetry. Miniaturization was achieved with fused silica microcapillary tubing entrapped in a polymeric casing. Scanning electron microscopy (SEM) was employed for the fabricated LLI support characterization. Voltammetric investigation of CTX+ at macro- and µ-ITIES allowed the determination of many physicochemical parameters, such as formal Galvani potential of the ion transfer reaction ([Formula: see text]), diffusion coefficients (D), formal free Gibbs energy of the ion transfer reaction (∆G'aq → org), and water-1,2-dichloroethane partition coefficient ([Formula: see text]). Additionally, based on the results obtained the analytical parameters including voltammetric sensitivity, limits of detection and the limits of quantification (in micromolar range) were calculated. The applicability of the developed procedures was verified in spiked still mineral and tap water samples.

Determination of quinine in tonic water at the miniaturized and polarized liquid-liquid interface.

In this work we report an electrochemical approach to quantitative and qualitative analysis of quinine (QN) at the interface between two immiscible electrolyte solutions (ITIES). This was done at the macroscopic (macroITIES) and microscopic (µITIES) systems using ion transfer voltammetry (ITV). The linear response of the peak current vs. increasing concentrations of QN at the µITIES was from 2.50 µM to 29.13 µM and the corresponding calculated limit of detection (LOD) for the current signals originating from QN transfer from the aqueous to the organic phase was equal to 0.49 µM. Additionally, the influence of pH (2-12) of the aqueous phase on the recorded QN signals was investigated. We have found that our method is fully applicable for QN direct determination in non-treated tonic water, as confirmed on three different real samples from three different manufacturers. Finally, a number of validation parameters for the developed method are provided and discussed.

Electrochemical study of ephedrine at the polarized liquid-liquid interface supported with a 3D printed cell.

In this work, we have examined an electrochemical behavior of the ephedrine at the polarized liquid-liquid interface (water/1,2-dichloroethane). In this respect, we first designed and then 3D printed polyamide-based electrochemical cell that was used as the liquid-liquid interface support during electroanalytical measurements. The protonated ephedrine undergoes a reversible ion transfer reaction with the standard Galvani potential difference equal to +0.269 V. This value was used to calculate the water - 1,2-dichloroethane logP equal to -4.6. Ion transfer voltammetry was used to build the calibration curve and allowed for the ephedrine detection from concentration equal to 20 µM. By varying the pH of the aqueous phase from 2 up to 12 we were able to plot the ion partition diagram that was further analyzed and provided several pharmacochemical information. To further push this work towards practical utility, we have formulated the artificial urine and studied the interfacial behavior of all its components at the polarized liquid-liquid interface. Ephedrine detection from real spiked urine samples was also performed.

Electrochemistry of catalase at a liquid|liquid micro-interface array.

The electrochemistry of catalase (CAT) was investigated at the interface between two immiscible electrolyte solutions (ITIES) as a step towards its detection. Electrochemistry at the ITIES offers advantages such as the non-redox detection of biomolecules. The electrochemical behaviour of CAT at the ITIES, in a micro-interface array format, displayed a distinct cyclic voltammogram when the aqueous phase pH was lower than the isoelectric point (pI) of CAT. No voltammetric response was observed when the aqueous phase pH > pI of CAT, indicating that neutral or negatively charged CAT has no capability to facilitate anion transfer from the organic phase. Adsorptive stripping voltammetry (AdSV) was assessed for detection of low concentrations at the µITIES array. Application of a positive preconcentration potential for a fixed time enabled interfacial accumulation of CAT as a complex; subsequently, a voltammetric scan to lower potentials desorbed the complex, providing the electroanalytical signal. Assessment of sample matrix effects by examining the electrochemistry of CAT in artificial serum indicated that detection in pH-adjusted samples is feasible. Together, these results demonstrate that CAT is electroactive at the liquid-liquid interface and this may be useful as a strategy to detect and characterize the enzyme in a label-free manner.

Ion transfer voltammetry for analytical screening of fluoroquinolone antibiotics at the water - 1.2-dichloroethane interface.

In this paper, the electrochemical behavior of four fluoroquinolone antibiotics (FAs) [Ciprofloxacin (Cip), Enrofloxacin (Enr), Marbofloxacin (Mar) and Ofloxacin (Ofl)] at a polarized interface between two immiscible electrolyte solutions (ITIES) has been studied using ion-transfer voltammetry (ITV). The measurements were conducted in the traditional macroscopic (macro-ITIES) and a recently developed miniaturized (micro-ITIES) platform. The latter was obtained from fused silica micro-capillaries having an internal diameter of 25 µm. We used macroITIES to obtain a number of analytical parameters such as: standard Galvani potential of ion transfer (ΔΦ0), diffusion coefficients (D), free Gibbs energy of ion transfer (ΔG0) and partition coefficients (logPDCE). The latter were compared with the available literature values of logPoctanol. The effect of concentration of the studied antibiotics on the electrochemical response was investigated with the microITIES platform, setting statistical parameters such as: linear dynamic ranges (LDRs - studied from 1 µM up to 50 µM), lower limit of detections (LODs - around 1 µM) and sensitivity (found in the range from 2.6·10-2 to 6.8·10-2 nA·µM-). MicroITIES were further used to study the effect of pH on the analytical signal and the results are plotted in a form of ion partition diagrams. Working with microITIES supported with the fused silica capillaries significantly reduced the volumes of consumed chemicals and expedite all analytical experiments. The provided results can be successfully applied in pharmacology and electroanalysis for testing and determination of the chosen fluoroquinolone antibiotics.

Template-Free and Spontaneous Formation of Vertically Aligned Pd Nanofiber Arrays at the Liquid-Liquid Interface between Redox-Active Ionic Liquid and Water.

Vertically aligned Pd nanofiber arrays (NFAs) have been prepared at the liquid-liquid interface between redox-active ionic liquid (RAIL) and water (W) via a template-free manner. The RAIL with high hydrophobicity, (ferrocenylmethyl)dodecyldimethylammonium bis(nonafluorobutanesulfonyl)amide, plays dual roles of reducing agent for Pd precursor ions and the hydrophobic liquid phase simultaneously, and the RAIL|W interface has been utilized as the formation site for the spontaneous growth of Pd NFAs. The Pd NFAs consist of three parts: layers formed by partly connected particles on the top, NFAs in the middle, and firm sheetlike layers on the bottom. Because of the top and bottom supporting layers, the antideformation ability and durability of the Pd NFAs with a length reaching several micrometers are enhanced. A possible mechanism for the formation of the Pd NFAs has been discussed. The Pd NFAs show a good stability and a higher electrocatalytic activity toward the ethanol oxidation reaction than a commercial Pd/C catalyst. The present study provides a new strategy for the template-free and spontaneous formation of Pd NFAs.

Investigation of a solvent-cast organogel to form a liquid-gel microinterface array for electrochemical detection of lysozyme.

Ion transfer at aqueous-organogel interfaces enables the non-redox detection of ions and ionisable species by voltammetry. In this study, a non-thermal method for preparation of an organogel was employed and used for the detection of hen-egg-white-lysozyme (HEWL) via adsorptive stripping voltammetry at an array of aqueous-organogel microinterfaces. Tetrahydrofuran solvent casting was employed to prepare the organogel mixture, hence removing the need for heating of the solution to be gelled, as used in previous studies. Cyclic voltammetry of HEWL at the microinterface array revealed a broad adsorption process on the forward scan, at positive applied potentials, followed by a desorption peak at ca. 0.68 V, indicating the detection of HEWL in this region. Application of an adsorption step, where a constant optimized potential of 0.95 V was applied, followed by voltammetric detection provided for a linear response range of 0.02-0.84 µM and a detection limit of 0.030 µM for 300 s adsorption. The detection limit was further improved by utilizing differential pulse stripping voltammetry, resulting in detection limits of 0.017 µM, 0.014 µM, and 0.010 µM for adsorptive pre-concentration times of 60, 120 and 300 s, respectively, in unstirred solutions. These results are an improvement over other methods for the detection of HEWL at aqueous-organic interfaces and offers a basis for the label-free detection of protein.

Electrochemical detection of ractopamine at arrays of micro-liquid | liquid interfaces.

The behaviour of protonated ractopamine (RacH(+)) at an array of micro-interfaces between two immiscible electrolyte solutions (micro-ITIES) was investigated via cyclic voltammetry (CV) and linear sweep stripping voltammetry (LSSV). The micro-ITIES array was formed at silicon membranes containing 30 pores of radius 11.09±0.12 µm and pore centre-to-centre separation of 18.4±2.1 times the pore radius. CV shows that RacH(+) transferred across the water |1,6-dichlorohexane µITIES array at a very positive applied potential, close to the upper limit of the potential window. Nevertheless, CV was used in the estimation of some of the drug's thermodynamic parameters, such as the formal transfer potential and the Gibbs transfer energy. LSSV was implemented by pre-concentration of the drug, into the organic phase, followed by voltammetric detection, based on the back-transfer of RacH(+) from the organic to aqueous phase. Under optimised pre-concentration and detection conditions, a limit of detection of 0.1 µM was achieved. In addition, the impact of substances such as sugar, ascorbic acid, metal ions, amino acid and urea on RacH(+) detection was assessed. The detection of RacH(+) in artificial serum indicated that the presence of serum protein interferes in the detection signal, so that sample deproteinisation is required for feasible bioanalytical applications.