Determination of Luteolin and Apigenin in Herbal Teas by Online In-Tube Solid-Phase Microextraction Coupled with LC-MS/MS.

Herbal teas have attracted attention as functional beverages containing luteolin and apigenin, which exhibit antioxidant and anti-inflammatory effects. The objective of this study was to develop a sensitive online automated method to determine these flavones' contents in herbal teas using in-tube solid-phase microextraction (IT-SPME) coupled with liquid chromatography-tandem mass spectrometry (LC-MS/MS). These compounds were extracted and concentrated by IT-SPME using a Supel Q PLOT capillary column and then separated and detected within 6 min using a CAPCELL PAK C18 MG III analytical column and a negative electrospray ionization-mode multiple-reaction monitoring system by LC-MS/MS. The detection limits (S/N = 3) for luteolin and apigenin were 0.4 and 0.8 pg mL-1, respectively, and the calibration curves were linear in the range of 2-2000 pg mL-1 with correlation coefficients above 0.9995, and intra-day and inter-day precisions with relative standard deviations below 2.9 and 3.6% (n = 6), respectively. The luteolin and apigenin in herbal tea were quantified using IT-SPME/LC-MS/MS following the acid hydrolysis of their glycosides. Among the 10 herbal teas tested, luteolin was detected in peppermint and sage at concentrations of 375 and 99 µg mL-1, respectively, while apigenin was detected in German chamomile at 110 µg mL-1, which were higher than in the other herbal teas. The method is expected to be a useful method for evaluating the efficacy of luteolin and apigenin in herbal teas as functional beverages.

A novel halloysite nanotubes-based hybrid monolith for in-tube solid-phase microextraction of polar cationic pesticides.

The accurate determination of polar cationic pesticides in food poses a challenge due to their high polarity and trace levels in complex matrices. This study hypothesized that the use of halloysite nanotubes (HNTs) can significantly enhance the extraction efficiency and sensitivity of these analytes because of their rich hydroxyl groups and cation exchange sites. Therefore, we chemically incorporated HNTs with organic polymer monoliths for in-tube solid-phase microextraction (SPME). This novel hybrid monolith extended service life, improved adsorption capacity, and exhibited excellent extraction performance for polar cationic pesticides. Based on these advancements, a robust and sensitive in-tube SPME-HILIC-MS/MS method was constructed to determine trace levels of polar cationic pesticides in complex food matrices. The method achieved limits of detection of 1.9, 2.1, and 0.1 µg/kg for maleic hydrazide, amitrole, and cyromazine, respectively. The spiked recoveries in five food samples ranged from 80.2 to 100.8%, with relative standard deviations below 10.7%.

A new approach towards highly sensitive detection of endogenous N-acetylaspartic acid, N-acetylglutamic acid, and N-acetylaspartylglutamic acid in brain tissues based on strong anion exchange monolith microextraction coupled with UHPLC-MS/MS.

A novel in-tube solid-phase microextraction coupled with an ultra-high performance liquid chromatography-mass spectrometry method has been established for simultaneous quantification of three crucial brain biomarkers N-acetylaspartic acid (NAA), N-acetylglutamic acid (NAG), and N-acetylaspartylglutamic acid (NAAG). A polymer monolith with quaternary ammonium as the functional group was designed and exhibited efficient enrichment of target analytes through strong anion exchange interaction. Under the optimized conditions, the proposed method displayed wide linear ranges (0.1-80 nM for NAA and NAG, 0.2-160 nM for NAAG) with good precision (RSDs were lower than 15%) and low limits of detection (0.019-0.052 nM), which is by far the most sensitive approach for NAA, NAG, and NAAG determination. Furthermore, this approach has been applied to measure the target analytes in mouse brain samples, and endogenous NAA, NAG, and NAAG were successfully detected and quantified from only around 5 mg of cerebral cortex, cerebellum, and hippocampus. Compared with existing methods, the newly developed method in the current study provides highest sensitivity and lowest sample consumption for NAA, NAG, and NAAG measurements, which would potentially be utilized in determining and tracking these meaningful brain biomarkers in diseases or treatment processes, benefiting the investigations of pathophysiology and treatment of brain disorders.

High-sensitive determination of tetracycline antibiotics adsorbed on microplastics in mariculture water using pre-COF/monolith composite-based in-tube solid phase microextraction on-line coupled to HPLC-MS/MS.

Microplastics (MPs) act as carriers for organic pollutants (e.g. antibiotics) and microorganisms (e.g. bacteria) in waters, leading to the proliferation of antibiotic resistance genes. Moreover, the antibiotics adsorbed on MPs may exacerbate this process. For further research, it is necessary to understand the types and amounts of antibiotics adsorbed on MPs. However, due to the heavy work of MPs collection and sample pretreatment, there is a lack of analytical methods and relevant data. In this study, an in-tube solid phase microextraction (IT-SPME) on-line coupled to HPLC-MS/MS method based on amorphous precursor polymer of three-dimensional covalent organic frameworks/monolith-based composite adsorbent was developed, which could efficiently capture, enrich and analyze tetracycline (TCs) antibiotics. Under the optimal extraction parameters, the developed method was capable of detecting TCs at levels as low as 0.48-1.76 pg. This method was applied to analyze the TCs adsorbed on MPs of different particle sizes in mariculture water for the first time, requiring a minimum amount of MPs of only 1 mg. Furthermore, it was observed that there could be an antagonistic relationship between algal biofilm and TCs loaded on MPs. This approach could open up new possibilities for analyzing pollutants on MPs and support deeper research on MPs.

Multivariate surface self-assembly strategy to fabricate ionic covalent organic framework surface grafting monolithic sorbent for enrichment of aristolochic acids prior to high performance liquid chromatography analysis.

Herein, an ionic covalent organic framework (iCOF) surface grafting monolithic sorbent was prepared by the multivariate surface self-assembly strategy for in-tube solid-phase microextraction (SPME) of trace aristolochic acids (AAs) in serum, traditional Chinese medicines (TCMs) and Chinese patent drug. Via adjusting the proportion of ionic COF building block during the self-assembly, the density of quaternary ammonium ions in the iCOF was modulated for the enhanced adsorption of AAs. The successful preparation of iCOF surface grafting monolithic sorbent was confirmed by different means. A multiple mode mechanism involving π-π stacking, hydrophobic, electrostatic and hydrogen-bonding interactions was primarily attributed to the adsorption. Several in-tube SPME operating conditions, such as the dosage of ionic COF building block, ACN percentage and TFA percentage in the sampling solution, ACN percentage and TFA percentage in eluent and the collection time span, were optimized to develop the online in-tube SPME-HPLC method for analysis of AAs. Under the optimized conditions, a good linearity was obtained in the concentration range of 20-1000 ng/mL for target AAs in serum samples, the limits of detection (LODs) were less than 10 ng/mL, while the recoveries ranged from 90.3 % to 98.7 % with RSDs (n = 5) below 7.9 %. This study developed a feasible approach to iCOF functionalized monolithic sorbent for SPME and further exhibited the vast potential for the application of COF based monolithic sorbent in sample preparation.

Task specific microextraction column based on monolith for magnetic field-assisted in-tube solid phase microextraction of vanadium species in complex samples prior to online chromatographic analysis.

The dominant species of vanadium (V) are V(IV) and V(V) which exhibit different toxicity and biological effects. Thus, speciation of V(IV) and V(V) is highly essential. Efficient sample preparation is the core step in the quantification of V(IV) and V(V). In the present study, a new task specific microextraction column based on monolith mingled with Fe3O4 nanoparticles (MBMC) was in situ synthesized in capillary and utilized as the extraction phase of magnetic field-assisted in-tube solid phase microextraction (MA-IT-SPME) of V(IV) and V(V) species which were coordinated with ethylene diamine tetraacetic acid (EDTA). The prepared MBMC presented porous and superparamagnetic properties, and possessed abundant functional groups. Results revealed that the exertion of magnetic field during adsorption and eluting steps boosted the extraction efficiency of V(IV)-EDTA and V(V)-EDTA chelates from 65.1 % to 55.7 %-90.0 % and 80.1 %, respectively. Under the beneficial extraction parameters, the established MA-IT-SPME was online hyphenated with HPLC/DAD to perform speciation of trace vanadium in water and vegetable samples, the achieved limits of detection were 0.054-0.060 µg/L and 1.4-1.5 µg/kg in water and vegetable samples, respectively, and the spiked recoveries varied from 82.5 to 118 %. In addition, relevant extraction mechanism under magnetic field was explored. In comparison with existing methods, the developed MA-IT-SPME technique displays some attractive merits such as automation, good anti-interference ability, high extraction efficiency, low cost and less use of organic solvent, in the capture of V species. The established online MBMC@MA-IT-SPME-HPLC/DAD system can become a competitive approach for sensitive speciation of V(IV) and V(V) at trace levels in complex samples.

[Application progress of on-line sample preparation techniques coupled with liquid chromatography-mass spectrometry system in the detection of food hazards].

Food safety has received increased attention, and food detection is of great significance. The food matrix is complex, and diverse food hazards have been identified. Thus, the detection methods and sample preparation techniques for food matrices must be continuously optimized and updated. Several steps are usually required when a chromatographic system is used to determine food hazards: sample preparation, that is, the separation of targets from different substrates using a suitable preprocessing method and target-substance separation and purification, which is usually achieved using chromatographic separation. The selection of an appropriate detector for qualitative and quantitative analyses is usually based on the properties of the target compound. The sample preparation procedure is considered the most time-consuming aspect of the entire food-analysis process. It is also prone to analytical errors. Therefore, optimization of the sample preparation process is a key issue in the field of chemical analysis. Researchers have developed a series of new, efficient, and accurate sample preprocessing methods, and an on-line sample-preparation system has been found to be a feasible approach. On-line sample preparation coupled with liquid chromatography-mass spectrometry (LC-MS) presents many advantages. First, manual operation could reduce analytical errors to ensure good accuracy and repeatability. It could also reduce the consumption of chemical reagents and avoid cross-contamination between samples. Furthermore, an on-line sample-preparation system could shorten the sample-preparation time and improve the detection efficiency. On-line sample preparation coupled with LC-MS has been widely applied in the fields of environment, biology, and food. On-line sample preparation systems coupled with LC-MS are divided into two modules: the first modules involves sample preparation and the second module involves the LC system. The first module remove impurities and isolates the target compounds in preparation for their qualitative and quantitative detection. The coupling of these two modules depends mainly on valve switching. In this paper, we introduce the most frequently used on-line sample-preparation techniques, including on-line solid phase extraction (on-line SPE), in-tube solid phase microextraction (in-tube SPME), and turbulent chromatography (TFC). We then describe the basic principles and coupling equipment of these three on-line analytical technologies in detail. The coupling equipment establishes a physical connection between the two modules. Next, we discuss the properties of different purification fillers in an on-line sample-preparation column. The applications and research progress of on-line systems for pesticide residues, veterinary drug residues, and biotoxins are also discussed. Compared with offline sample preparation, on-line analytical systems present several advantages. On-line analytical systems can not only greatly reduce the analysis time and solvent consumption but also improve the detection sensitivity and accuracy. Such systems can be used to determine food hazards to ensure food safety. Finally, the existing problems and development trends of on-line analytical systems are discussed and prospected. To promote the applications of on-line analytical technology in food-safety detection, we suggest that the following three aspects be considered. First, more on-line purification columns with novel fillers, in addition to C18 or polymer fillers, should be developed. Second, compared with ordinary detectors, high-resolution MS detectors have better precision and accuracy. Coupling on-line analytical technologies with a high-resolution mass spectrometer may be beneficial for the further development of on-line analyses. Third, different food matrices should be compared and evaluated to continuously optimize the detection process and improve the efficiency of on-line analytical systems. As concerns regarding food safety issues have increased, the applications of on-line analytical technologies for food detection can be expected to become increasingly important.

Simultaneous analysis of carcinogenic N-nitrosamine impurities in metformin tablets using on-line in-tube solid-phase microextraction coupled with liquid chromatography-tandem mass spectrometry.

Contamination of active pharmaceutical ingredients (APIs) and pharmaceutical preparations with carcinogenic N-nitrosamines has led to recalls of these products and supply shortages to patients. The present study describes the development of a highly sensitive method for simultaneous analysis of seven N-nitrosamines using on-line in-tube solid-phase microextraction (IT-SPME) coupled with liquid chromatography-tandem mass spectrometry (LC-MS/MS) to determine their actual contamination in metformin tablets. Using a Carboxen 1006 PLOT capillary as the extraction device for IT-SPME, these compounds were efficiently extracted and concentrated 6‒24-fold by subjecting 40 µL of sample to 25 repeated draw/eject cycles at a rate of 0.2 mL/min. The seven N-nitrosamines were separated within 11 min by gradient elution with 0.1 % formic acid solution and acetonitrile as the mobile phase using a CAPCELL PAK C18 MGII column and detected by multiple reaction monitoring in positive ion mode. The calibration curve showed linearity in the range 0.2‒50 ng/mL and detection limits (S/N = 3) in the range 3‒112 pg/mL. The intra-day and inter-day precisions were less than 5.5 % and 7.0 % (n = 6), respectively, with accuracies ranging from 93‒117 %. Following ultrasonic extraction with water, centrifugation and filtration of the supernatant liquid through a membrane filter, the N-nitrosamine impurities in metformin tablets could be analyzed by IT-SPME/LC‒MS/MS. Their limits of quantification (S/N = 10) were 0.1‒5.1 pg/mg API and recoveries ranged from 87‒102 %. Analysis of eight metformin tablets from eight manufacturers showed that 5.8‒7.5 pg/mg N-nitrosodimethylamine were present in three tablets, with no other N-nitrosamines detected in any of the eight tablets. This method may be useful in testing for N-nitrosamine impurities in pharmaceutical preparations.

MXene nanosheets woven in polyacrylonitrile nanofiber yarns aligned spider web as a highly efficient sorbent for in-tube solid phase microextraction of beta-blockers from biofluids.

The use of electrospinning has received much attention in the production of nanofiber webs due to its advantages such as flexibility and simplicity. The direct electrospinning of nanofibers in an aligned or twisted form and the production of nanofiber yarns can turn nanofibers into woven fabrics, which leads to an increase in the diversity of nanofiber applications and improves their end-use possibilities. In this work, a victorious nanofiber yarn spinning system was used with the help of a rotating funnel. Yarn formation was studied using a composited polyacrylonitrile (PAN)/MXene polymer solution ejected from two oppositely charged nozzles. Finaly their application for packed-in-tube solid-phase microextraction of ß-blocker drugs from biofluids was demonstrated. The separation and quantification of analytes were performed by HPLC-UV instrument. The 3D-yarn PAN/MXene sorbent exhibited high flexibility, porosity, sorbent loading, mechanical stability, and a long lifetime. The characterization of the final nanofiber was carried out utilizing Fourier-transform infrared spectroscopy, field emission scanning electron microscope, energy-dispersive X-ray mapping, transmission electron microscope and X-ray diffraction analysis. Various parameters that affect the extraction efficiency, such as extraction time, pH, ionic strength and flow rate of sample solution, and type, volume and flow rate of eluent, were investigated and optimized. Under optimized conditions, the limits of detection were obtained in the range of 1.5-3.0 µg L-1. This method demonstrated appropriate linearity for ß-blockers in the range of 5.0-1000.0 µg L-1, with coefficients of determination greater than 0.990. The inter- and intra-assay precisions (RSDs, for n = 3) are in the range of 2.5-3.5%, and 4.5-5.2%, respectively. Finally, the validated method was put in an application for the analysis of atenolol, propranolol and betaxolol in human urine and saliva samples at different hours and acceptable relative recoveries were obtained in the range of 89.5% to 110.4%.

Study of the degradation of diphenyl-ether herbicides aclonifen and bifenox in different environmental waters.

The degradation of the diphenyl-ether herbicides aclonifen (ACL) and bifenox (BF) in water samples has been studied under different laboratory conditions, using in-tube solid-phase microextraction (IT-SPME) coupled to capillary liquid chromatography (capLC). The working conditions were selected in order to detect also bifenox acid (BFA), a compound formed as a result of the hydroxylation of BF. Samples (4 mL) were processed without any previous treatment, which allowed the detection of the herbicides at low ppt levels. The effects of temperature, light and pH on the degradation of ACL and BF have been tested using standard solutions prepared in nanopure water. The effect of the sample matrix has been evaluated by analysing different environmental waters spiked with the herbicides, namely ditch water, river water and seawater. The kinetics of the degradation have been studied and the half-life times (t1/2) have been calculated. The results obtained have demonstrated that the sample matrix is the most important parameter affecting the degradation of the tested herbicides. The degradation of both ACL and BF was much faster in ditch and river water samples, where t1/2 values of only a few days were observed. However, both compounds showed a better stability in seawater samples, where they can persist for several months. In all matrices ACL was found to be more stable than BF. In samples where BF had been substantially degraded, BFA was also detected, although the stability of this compound was also limited. Other degradation products have been detected along the study.

Online measurement of tetraethyllead in aqueous samples utilizing monolith-based magnetism-enhanced in-tube solid phase microextraction coupled with chromatographic analysis.

A new procedure that utilizing a preconcentration system based on magnetism-enhanced in-tube solid phase microextraction (ME/IT-SPME) and detection by HPLC with diode array detector (DAD) after liquid desorption from the microextraction column has been developed for the online measurement of tetraethyllead (TEL) in various aqueous samples. In this connection, according to the chemical features of TEL, porous monolith mingled with Fe3O4 nanoparticles were designed and synthesized in a silica capillary, and used as the microextraction column of ME/IT-SPME. To favor the implement of variable magnetic fields during extraction procedure, the as-prepared microextraction column was twined a magnetic coil. Results revealed that the exertion of magnetic field during the adsorption and eluting procedures assisted the extraction of TEL with an enhancement by 52% in extraction efficiency. Under the most beneficial conditions, the developed ME/IT-SPME was online hyphenated with HPLC/DAD to measure trace TEL in various aqueous samples. The limit of detection was 0.082 µg/L and the RSDs for precision were in the range of 6.3-8.5%. The recoveries with low, medium and high fortified levels varied from 80.6% to 95.0% with good repeatability. To the best of knowledge, this is the first study that using IT-SPME to extract TEL and then online quantification with HPLC/DAD.

Direct coupling in-tube solid-phase microextraction with mass spectrometry using polymer coated open-tubular column for rapid analysis of antiepileptic drugs in biofluids.

Development of high-throughput and rapid screening analytical method is in high demand for anti-doping and clinical point-of-care (POC) analysis. Solid-phase microextraction and mass spectrometry direct coupling (SPME-MS) has been proved as a rapid and effective way for target analysis in complex sample matrixes. An online direct coupling of in-tube SPME (IT-SPME) with MS using polymer coated open-tubular column has been developed in this work. A sharp stainless-steel needle was attached at the end of the SPME column, which enables the direct ionization of the analytes after elution from the IT-SPME column. Itaconic acid-benzene co-polymer was in-situ grown on the inner surface of the fused silica capillary and used as extraction phase. This column has low backpressure and provides both hydrophobic and weak cationic exchange interaction with the target analytes due to the chemical properties. The developed online IT-SPME-MS method showed good extraction performance towards various target analytes and good reusability at least for 60 times. As a proof-of-concept application, the above method was applied for the analysis of antiepileptic drugs (AEDs) in both plasma and urine samples with linear range (1 ng/mL-200 ng/mL), good linearity (R2 ≥ 0.99), and good reproducibility (intra-day RSDs less than 4.36%, inter-day RSDs less than 6.55%). The method exhibited high enrichment factors between 187 and 204 for the two AEDs and high sensitivity for the analysis of human plasma samples and urine samples.

[Preparation and application of graphene oxide functionalized melamine-formaldehyde aerogel coated solid-phase microextraction tube].

Many solid-phase microextraction (SPME) sorbents have been developed from aerogels because of their low densities, large surface areas, and high porosities. Melamine-formaldehyde (MF) aerogel, made from melamine and formaldehyde by a sol-gel reaction, is one of the typical organic aerogels. MF aerogel has better mechanical strength, chemical stability and extraction performance than inorganic aerogels. The performance of the aerogel is limited in some fields, while composite aerogels can meet different requirements such as good mechanical strength and strong adsorption performance. Graphene oxide (GO) is a two-dimensional nanomaterial composed of a single layer of carbon atoms and provides π-π interaction by a large π-electron. In addition, the oxygen-containing groups at the edge of the lamellar structure improve the hydrophilicity of the material and can interact with various compounds. To improve the extraction performance of MF aerogel for polycyclic aromatic hydrocarbons (PAHs), GO/MF aerogels were prepared by functionalizing MF aerogel with GO. In this study, 1.2612 g of melamine and 80 mg of sodium carbonate were dissolved in 30 mL of water, and the mixture was heated to 80 ℃ under stirring. Then, 2.8 mL formaldehyde solution (37%) was slowly added, and a clear solution was obtained gradually. Next, 50 mg of GO powder was ultrasonically dispersed in 10.0 mL of water and evenly mixed with the above solution. After adjusting the pH to 1.5, the sol-gel process was performed for 48 h, then the gel was aged at room temperature for 24 h. The gel was then soaked in ethanol, acetone, and cyclohexane in turn to replace the solvent. Finally, the GO/MF aerogel was obtained by freeze-drying for 24 h. The GO/MF aerogel was characterized by scanning electron microscopy (SEM) and X-ray photoelectric spectroscopy (XPS), confirming that GO was successfully introduced into MF aerogel, while retaining its three-dimensional network and porous structure. GO/MF aerogel was coated onto the surface of a stainless steel wire to be used as sorbent. Four such wires were placed into a polyetheretherketone (PEEK) tube (0.75 mm i. d., 30 cm length) for in-tube (IT) SPME. The tube was combined with a high-performance liquid chromatography (HPLC) unit to construct an IT-SPME-HPLC online system. When the six-way valve was in the Load state, sample solution achieved online enrichment with analytes while it flowed through the extraction tube. After extraction, the valve was turned to the Inject state, and the analytes were eluted into the chromatographic column by the mobile phase at a flow rate of 1.0 mL/min for separation and detection with the detector. Under the same extraction conditions (sampling volume=30 mL, sampling rate=1.00 mL/min, and concentration of polycyclic aromatic hydrocarbons (PAHs, viz. naphthalene (Nap), acenaphthylene (Acy), acenaphthene (Ace), fluorine (Flu), phenanthrene (Phe), anthracene (Ant), fluoranthene (Fla) and pyrene (Pyr))=5.00 µg/L), GO/MF aerogel-based tube was compared with that of MF aerogel-based tube. GO enhanced the enrichment efficiency of MF aerogel towards PAHs from 1.1 to 2.5 times, due to the increased number of adsorption sites and enhanced π-π interaction with PAHs. IT-SPME was affected by the sampling volume, sampling rate, concentration of organic solvent in sample, desorption solvent, desorption rate, and desorption time. To obtain accurate results, the main extraction and desorption conditions (sampling volume, sampling rate, organic solvent concentration, desorption time) were investigated carefully. As the sampling volume in the extraction tube was increased, the extraction efficiency was found to increase gradually until saturation. In this study, the extraction efficiency was investigated for sampling volumes ranging from 30 to 80 mL, and 70 mL was selected as a suitable sampling volume to achieve satisfactory extraction efficiency. The sampling rate affects not only the extraction efficiency, but also the extraction time. When the sample flows through the extraction tube at a low rate, it requires a long test time. Although the increase in sampling rate reduces the extraction time, it often decreases extraction efficiency. In addition, large sampling rate leads to high pressure in the tube, which in turn reduces the service life of the tube. Therefore, the effect of sampling rate (1.25-2.50 mL/min) on extraction efficiency was investigated, and good extraction efficiency and short test time were achieved when the sampling rate was 2 mL/min. High hydrophobic PAHs have poor solubility in water. An appropriate amount of organic solvent in the sample solution can improve the solubility of PAHs to obtain accurate analytical results. However, the extraction efficiency was affected by the added organic solvent. Thus, the effect of volume fraction of methanol (0, 0.5%, 1%, 2%, 3%, and 5%, v/v) on the extraction efficiency was investigated. The sample solution without methanol afforded better extraction efficiency and satisfactory repeatability. After online extraction, the desorption directly affects the desorption efficiency. The peak areas of the eight PAHs were investigated with different desorption times (0.2, 0.4, 0.6, 0.8, 1.0, and 2.0 min), and a desorption time of 2.0 min was required to fully desorb all analytes and reduce their residuals. The IT-SPME-HPLC-DAD method was established under the optimized conditions, and the limits of detection (LODs), linear equations, linear ranges, and correlation coefficients were obtained. The LODs of the eight PAHs were in the range of 0.001-0.005 µg/L, the quantitative ranges of the analytes were 0.003-15.0 µg/L for Fla and Pyr, 0.010-20.0 µg/L for Phe and Ant, and 0.017-20.0 µg/L for Nap, Acy, Ace and Flu, the enrichment factors were in the range of 2029-2875, and the analytical precision was satisfactory (intra-day RSD%≤4.8%, and inter-day RSD≤8.6%). Compared with some reported methods, the method reported herein provided higher sensitivity, wider linear range, and shorter test time. This method was applied to the detection of PAHs in common drinking water, including bottled mineral water and water from drinking fountain. The satisfactory recovery (76.3%-132.8%) obtained proves that the method is suitable for the determination of trace PAHs in real water samples, with high sensitivity, rapid testing, online detection, and good accuracy. The extraction tube also exhibited satisfactory durability and chemical stability.

Porous capillary monolithic column coupled with ultrahigh performance liquid chromatography-tandem mass spectrometry for fast and effective separation and determination of estrogens.

In this work, a porous capillary monolithic column was simply prepared by in situ thiol-alkyne click polymerization of dipentaerythritol hexakis (3-mercaptopropionate) and dimethyl dipropargylmalonate in fused-silica capillary. The capillary monolithic column shows excellent permeability, high porosity, and thoiether-rich groups, thereby, a high-efficient capacity for trace estrogens from complex samples are obtained via electron-donor-acceptor π-π interaction and hydrophobic interaction. The highest adsorption efficiency for estrogens is achieved at pH = 7.0 with a flow rate of 0.200 mL min-1. The superior adsorption capacities of the as-prepared capillary column for eight estrogens range from 0.092 mg m-1 to 0.31 mg m-1. A simple, reliable, and sensitive method for the determination of eight estrogens in biological and environmental samples is developed using the monolithic polymer as in-tube solid-phase microextraction coupled with ultrahigh performance liquid chromatography-tandem mass spectrometry (SPME-UPLC-MS/MS), and the total instrumental analysis time for the SPME-UPLC-MS/MS procedures was about 60 min per sample. The developed method shows a wide linear range (0.0500-5.00 µg L-1), and low limits of detection (5.34-9.63 ng L-1) for estrogens. The concentrations of estrogens in serum, urine, and pond water samples are found to be no more than 3.69, 0.741, and 1.04 µg L-1, respectively, and the satisfying recoveries for the eight estrogens range from 80.3% to 113% with relative standard deviations (n = 5) of 1.5-9.4%. The established method is highly potential for extraction and analysis of ultratrace target estrogens in complex matrices, such as biological and environmental samples.

Speciation of organotin compounds in water and seafood samples by online hyphenation of porous polymer-based magnetism-enhanced in-tube solid phase microextraction and HPLC.

A new strategy based on online hyphenation of magnetism-enhanced in-tube solid phase microextraction (ME-SPME) and HPLC was developed for speciation of organotin compounds (OTCs) in water and seafood samples. Task specific porous polymer embedded magnetic nanoparticles (TPM) was fabricated in capillary and utilized as the microextraction column (MEC) of ME-SPME. The implement of magnetic field during extraction duration obviously improved extraction efficiencies of prepared TPM/MEC towards studied TOCs from 48.0-77.0% to 84.2-99.7%. Under the optimized extraction parameters, sensitive and automatic approach for the quantification of TOCs was developed by online hyphenation of ME-SPME and HPLC with fluorescence detection. The limits of detection for water and seafood samples were in the ranges of 0.0030-1.5 µg/L and 0.71-14 µg/kg, respectively. The established method was employed to measure low contents of studied OTCs in actual samples, and the recoveries at different fortified contents varied from 80.2% to 116% with satisfactory reproducibility (RSDs below 10%). In addition, confirmation experiments were adopted to inspect the accuracy of introduced method.

Online In-Tube Solid-Phase Microextraction Coupled with Liquid Chromatography-Tandem Mass Spectrometry for Automated Analysis of Four Sulfated Steroid Metabolites in Saliva Samples.

Accurate measurement of sulfated steroid metabolite concentrations can not only enable the elucidation of the mechanisms regulating steroid metabolism, but also lead to the diagnosis of various related diseases. The present study describes a simple and sensitive method for the simultaneous determination of four sulfated steroid metabolites in saliva, pregnenolone sulfate (PREGS), dehydroepiandrosterone sulfate (DHEAS), cortisol sulfate (CRTS), and 17ß-estradiol-3-sulfate (E2S), by online coupling of in-tube solid-phase microextraction (IT-SPME) and stable isotope dilution liquid chromatography-tandem mass spectrometry (LC-MS/MS). These compounds were extracted and concentrated on Supel-Q PLOT capillary tubes by IT-SPME and separated and detected within 6 min by LC-MS/MS using an InertSustain swift C18 column and negative ion mode multiple reaction monitoring systems. These operations were fully automated by an online program. Calibration curves using their stable isotope-labeled internal standards showed good linearity in the range of 0.01-2 ng mL-1 for PREGS, DHEAS, and CRTS and of 0.05-10 ng mL-1 for E2S. The limits of detection (S/N = 3) of PREGS, DHEAS, CRTS, and E2S were 0.59, 0.30, 0.80, and 3.20 pg mL-1, respectively. Moreover, intraday and interday variations were lower than 11.1% (n = 5). The recoveries of these compounds from saliva samples were in the range of 86.6-112.9%. The developed method is highly sensitive and specific and can easily measure sulfated steroid metabolite concentrations in 50 µL saliva samples.

Smart Titanium Wire Used for the Evaluation of Hydrophobic/Hydrophilic Interaction by In-Tube Solid Phase Microextraction.

Evaluation of the hydrophobic/hydrophilic interaction individually between the sorbent and target compounds in sample pretreatment is a big challenge. Herein, a smart titanium substrate with switchable surface wettability was fabricated and selected as the sorbent for the solution. The titanium wires and meshes were fabricated by simple hydrothermal etching and chemical modification so as to construct the superhydrophilic and superhydrophobic surfaces. The micro/nano hierarchical structures of the formed TiO2 nanoparticles in situ on the surface of Ti substrates exhibited the switchable surface wettability. After UV irradiation for about 15.5 h, the superhydrophobic substrates became superhydrophilic. The morphologies and element composition of the wires were observed by SEM, EDS, and XRD, and their surface wettabilities were measured using the Ti mesh by contact angle goniometer. The pristine hydrophilic wire, the resulting superhydrophilic wire, superhydrophobic wire, and the UV-irradiated superhydrophilic wire were filled into a stainless tube as the sorbent instead of the sample loop of a six-port valve for on-line in-tube solid-phase microextraction. When employed in conjunction with HPLC, four kinds of wires were comparatively applied to extract six estrogens in water samples. The optimal conditions for the preconcentration and separation of target compounds were obtained with a sample volume of 60 mL, an injection rate of 2 mL/min, a desorption time of 2 min, and a mobile phase of acetonile/water (47/53, v/v). The results showed that both the superhydrophilic wire and UV-irradiated wire had the highest extraction efficiency for the polar compounds of estrogens with the enrichment factors in the range of 20-177, while the superhydrophobic wire exhibited the highest extraction efficiency for the non-polar compounds of five polycyclic aromatic hydrocarbons (PAHs). They demonstrated that extraction efficiency was mainly dependent on the surface wettability of the sorbent and the polarity of the target compounds, which was in accordance with the molecular theory of like dissolves like.

Packed in-tube SPME-LC-MS/MS for fast and straightforward analysis of cannabinoids and metabolites in human urine.

Cannabinoids are pharmacologically active compounds present in cannabis plants, which have become important research topics in the modern toxicological and medical research fields. Not only is cannabis the most used drug globally, but also cannabinoids have a growing use to treat a series of diseases. Therefore, new, fast, and efficient analytical methods for analyzing these substances in different matrices are demanded. This study developed a new packed-in-tube solid-phase microextraction (IT-SPME) method coupled to liquid chromatography with tandem mass spectrometry (LC-MS/MS), for the automated microextraction of seven cannabinoids from human urine. Packed IT-SPME microcolumns were prepared in (508 µm i.d. × 50 mm) stainless-steel hardware; each one required only 12 mg of sorbent phase. Different sorbents were evaluated; fractional factorial design 24-1 and a central composite design were employed for microextraction optimization. Under optimized conditions, the developed method was a fast and straightforward approach. Only 250 µl of urine sample was needed, and no hydrolysis was required. The sample pretreatment included only dilution and centrifugation steps (8 min), whereas the complete IT-SPME-LC-MS/MS method took another 12 min, with a sample throughput of 3 samples h-1 . The developed method presented adequate precision, accuracy and linearity; R2 values ranged from 0.990 to 0.997, in the range of 10-1000 ng ml-1 . The lower limits of quantification varied from 10 to 25 ng ml-1 . Finally, the method was successfully applied to analyze 20 actual urine samples, and the IT-SPME microcolumn was reused over 150 times.

Conductive polymer sorbent for extraction and determination of resveratrol and polydatin in Polygonum cuspidatum root samples.

INTRODUCTION: The quantitative analysis of trace resveratrol and polydatin in plant tissues is suitable for elucidation of the compounds' mechanisms of action. OBJECTIVES: The main objective of this work was to develop a feasible and effective sample pretreatment method to measure the concentrations of resveratrol and polydatin in complex samples. METHODOLOGY: A polymer sorbent, poly(2-mercaptobenzimidazole), was electrochemically prepared and utilized for selective extraction, while resveratrol and polydatin were used as target analytes. The sorbent was characterized by cyclic voltammetry, scanning electron microscopy and Fourier transform infrared spectroscopy. After extraction and elution, the analytes were analyzed by a Thermo U3000 HPLC system. Several affecting parameters, including the volume of elution solution, sample pH value, sample flow rate and sample volume, were evaluated and optimized. RESULTS: The proposed method showed good linearity with low limits of detection (from 0.5 to 0.8 ng·mL-1 ) and ideal accuracy with spiked recoveries from 81.30% to 99.16%. A good enrichment factor (more than 200-fold) together with good sensitivity was obtained with this method. Analysis of resveratrol and polydatin in Polygonum cuspidatum samples by this method is efficient. CONCLUSION: The method developed in this work exhibits several significant merits, including easy operation and high extraction efficiency, indicating that electrochemically prepared polymer sorbent is useful for sample pretreatment and analysis of traditional Chinese medicine samples.

A novel polyhedral oligomeric silsesquioxane-based hybrid monolith as a sorbent for on-line in-tube solid phase microextraction of bisphenols in milk prior to high performance liquid chromatography-ultraviolet detection analysis.

An on-line in-tube solid-phase microextraction (in-tube SPME) coupled with high-performance liquid chromatography (HPLC) method was proposed based on a novel polyhedral oligomeric silsesquioxane (POSS)-hybrid monolith for the determination of four bisphenols (BPs) in milk. The monolith was synthesized using acrylamide (AM) and monomethacrylate-functionalized POSS (mono-MA-POSS) as functional monomers to copolymerize with ethylene dimethacrylate (EDMA). Due to the abundant hydrogen bonding, π-π and hydrophobic interaction sites, the synthetic monolith displayed satisfying extraction performance for target BPs. Under the optimized conditions, the developed on-line in-tube SPME-HPLC method exhibited low limits of detection (LODs) (0.030-0.055 ng mL-1). The spiked recoveries were between 85.4 % and 111.8 %, and the relative standard deviations (RSDs) were less than 3.5 % for all the analytes. The results showed that the proposed method provided alternative for the analysis of BPs in complex samples.