RESUMO
The recent oscillation events in offshore wind farms (OWFs) connected via a modular multilevel-converter-based HVDC (MMC-HVDC) system are developing towards a wider frequency band, which causes complex a small-signal interaction phenomenon and difficulties in the stability analysis and control. In this paper, the wideband dynamic interaction mechanism is investigated based on the impedance analysis method and an improved control strategy using an optimization algorithm is proposed to improve the small-signal stability and reduce the oscillation risks. First, the detailed impedance models of the grid-connected system are established considering the distribution characteristics of the submarine cable, control delay and frequency coupling effect. Then, combined with the active damping control method, the wideband resonance mechanism is analyzed, and the stability constraints of controller parameters are obtained using the impedance stability criterion. Finally, an improved multi-objective slime mold algorithm (MOSMA)-based coordinated optimization control strategy is proposed to enhance the adaptability of the controller parameters and the wideband damping ability of a grid-connected system, which can improve the wideband stability of the system. The simulation and experimental results verify the proposed control strategy.
RESUMO
Open circuit failure mode in insulated-gate bipolar transistors (IGBT) is one of the most common faults in modular multilevel converters (MMCs). Several techniques for MMC fault diagnosis based on threshold parameters have been proposed, but very few studies have considered artificial intelligence (AI) techniques. Using thresholds has the difficulty of selecting suitable threshold values for different operating conditions. In addition, very little attention has been paid to the importance of developing fast and accurate techniques for the real-life application of open-circuit failures of IGBT fault diagnosis. To achieve high classification accuracy and reduced computation time, a fault diagnosis framework with a combination of the AC-side three-phase current, and the upper and lower bridges' currents of the MMCs to automatically classify health conditions of MMCs is proposed. In this framework, the principal component analysis (PCA) is used for feature extraction. Then, two classification algorithms-multiclass support vector machine (SVM) based on error-correcting output codes (ECOC) and multinomial logistic regression (MLR)-are used for classification. The effectiveness of the proposed framework is validated by a two-terminal simulation model of the MMC-high-voltage direct current (HVDC) transmission power system using PSCAD/EMTDC software. The simulation results demonstrate that the proposed framework is highly effective in diagnosing the health conditions of MMCs compared to recently published results.
Assuntos
Inteligência Artificial , Máquina de Vetores de Suporte , Algoritmos , Simulação por Computador , Análise de Componente PrincipalRESUMO
In order to make the grid-connected composite device (GCCD) controller meet the requirements of different operating modes and complex working conditions of power grid, this paper proposes to introduce sliding mode control (SMC) into GCCD controller. Firstly, the mathematical model of MMC converter is established, and the sliding mode controller is designed based on the SMC principle. Then, aiming at the problems of complex controller structure and difficult parameter tuning in multiple modes of the GCCD, this paper proposes a controller parameter optimization method based on improved Month Flame optimization (IMFO) algorithm. This method improves the MFO algorithm by introducing good point set (GPS) initialization and Levy flight strategy, which accelerates the convergence speed of the algorithm while avoiding falling into local optimization, and realizes the optimization of converter controller parameters. Under a variety of standard test functions, the advantages of the proposed IMFO algorithm are verified by comparing it with the traditional algorithm. Finally, in order to realize the automatic tuning of control parameters, the Python-PSCAD joint simulation method is studied and implemented. Taking the comprehensive integral of time and absolute error (CITAE) index as the objective function, the parameters of the sliding mode controller are optimized. The simulation results show that the controller parameters optimized by the IMFO algorithm can make the GCCD have better dynamic performance.
RESUMO
Fault detection and classification are two of the challenging tasks in Modular Multilevel Converters in High Voltage Direct Current (MMC-HVDC) systems. To directly classify the raw sensor data without certain feature extraction and classifier design, a long short-term memory (LSTM) neural network is proposed and used for seven states of the MMC-HVDC transmission power system simulated by Power Systems Computer Aided Design/Electromagnetic Transients including DC (PSCAD/EMTDC). It is observed that the LSTM method can detect faults with 100% accuracy and classify different faults as well as provide promising fault classification performance. Compared with a bidirectional LSTM (BiLSTM), the LSTM can get similar classification accuracy, requiring less training time and testing time. Compared with Convolutional Neural Networks (CNN) and AutoEncoder-based deep neural networks (AE-based DNN), the LSTM method can get better classification accuracy around the middle of the testing data proportion, but it needs more training time.
Assuntos
Memória de Curto Prazo , Redes Neurais de Computação , Eletricidade , Memória de Longo PrazoRESUMO
In this paper, we explore learning methods to improve the performance of the open-circuit fault diagnosis of modular multilevel converters (MMCs). Two deep learning methods, namely, convolutional neural networks (CNN) and auto encoder based deep neural networks (AE-based DNN), as well as stand-alone SoftMax classifier are explored for the detection and classification of faults of MMC-based high voltage direct current converter (MMC-HVDC). Only AC-side three-phase current and the upper and lower bridges' currents of the MMCs are used directly in our proposed approaches without any explicit feature extraction or feature subset selection. The two-terminal MMC-HVDC system is implemented in Power Systems Computer-Aided Design/Electromagnetic Transients including DC (PSCAD/EMTDC) to verify and compare our methods. The simulation results indicate CNN, AE-based DNN, and SoftMax classifier can detect and classify faults with high detection accuracy and classification accuracy. Compared with CNN and AE-based DNN, the SoftMax classifier performed better in detection and classification accuracy as well as testing speed. The detection accuracy of AE-based DNN is a little better than CNN, while CNN needs less training time than the AE-based DNN and SoftMax classifier.