Study on the Technology and Properties of Green Laser Sintering Nano-Copper Paste Ink.

With the rapid development of integrated circuits, glass substrates are frequently utilized for prototyping various functional electronic circuits due to their superior stability, transparency, and signal integrity. In this experiment, copper wire was printed on a glass substrate using inkjet printing, and the electronic circuit was sintered through laser irradiation with a 532 nm continuous green laser. The relationship between resistivity and microstructure was analyzed after laser sintering at different intensities, scanning speeds, and iterations. The experimental results indicate that the conductivity of the sintered lines initially increases and then decreases with an increase in laser power and scanning speed. At the same power level, multiple sintering runs at a lower scanning speed pose a risk of increased porosity leading to reduced conductivity. Conversely, when the scanning speed exceeds the optimal sintering speed, multiple sintering runs have minimal impact on porosity and conductivity without altering the power.

Reaction-Driven Migration Dynamics of Nano-Metal Particles Unraveled by Quantitative Electron Microscopies.

The stability of supported nano-metal catalysts holds significant importance in both scientific and economic practice, beyond the long pursuit of enhanced activity. While previous efforts have concentrated on augmenting the interaction between nano-metals and carriers, in the thermodynamic macro-perspective, to achieve optimized repression upon particle migration coalescence and Ostwald ripening, nevertheless, the microscale kinetics of migrating catalyst particles driven by the reaction remains unknown. In this work, the migration of nano-copper particles is investigated during hydrogen oxidation reaction by utilizing high spatiotemporal resolution of environmental transmission electron microscopy. It is shown that there exists a delicate correlation between the migration dynamics of nano-copper particles and the evolution of asymmetrically distributed Cu and Cu2O phases over the particle surface. It is found that the interplay of reduction and oxidation near the surface areas filled with Cu and Cu2O phases can facilitate the pressure gradient, which drives the migration of nano-particles. A driving force model is therefore established which is capable of qualitatively explaining the influences of reaction conditions such as temperature and hydrogen-to-oxygen ratio on the reaction-driven particle migration. This work adds a potential yet critical perspective to understanding particle migration and thus the nano-metal catalyst particle sintering in heterogeneous catalysis.

Disruption of bacterial biofilms by a green synthesized artemisinin nano-copper nanomaterial.

Bacterial biofilms are associated with antibiotic resistance and account for ∼80% of all bacterial infections. In this study, we explored novel nanomaterials for combating bacteria and their biofilms. Artemisinin nano-copper (ANC) was synthesized using a green synthesis strategy, and its shape, size, structure, elemental composition, chemical valence, zeta potential, and conductivity were characterized using transmission electron microscopy, X-ray diffractometer, X-ray photoelectron spectroscopy, zeta potential, and dynamic light scattering. The results showed that ANC was successfully synthesized utilizing a liquid phase chemical reduction method using chitosan as a modified protectant and l-ascorbic acid as a green reducing agent. The stability of ANC was evaluated using dynamic light scattering. The results showed that the particle size of ANC at different concentrations was comparable to that of the original solution after 7 days of storage, and there was no significant change in the polydispersity index (P > 0.05). The antibacterial effects of ANC on Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) were determined by disc diffusion and broth dilution methods. The results demonstrated that ANC inhibited and killed E. coli and S. aureus. The effect of ANC on bacterial biofilms was investigated using crystal violet staining, scanning electron microscopy, laser confocal microscopy, and quantitative polymerase chain reaction. The results showed that ANC treatment was able to destroy bacterial biofilms and downregulate biofilm- and virulence-related genes in E. coli (HlyA, gyrA, and F17) and S. aureus (cna, PVL, ClfA, and femB). Green-synthesized ANC possesses excellent antibiofilm properties and is expected to exhibit antibacterial and antibiofilm properties.

Molecular characterization and evaluation of novel management options for Burkholderia glumae BG1, the causative agent of panicle blight of rice (Oryza sativa L.).

BACKGROUND: Bacterial panicle blight, incited by Burkholderia glumae, has impacted rice production globally. Despite its significance, knowledge about the disease and the virulence pattern of the causal agent is very limited. Bacterial panicle blight is a major challenge in the rice-growing belts of North-western India, resulting in yield reduction. However, the management of B. glumae has become a challenge due to the lack of proper management strategies. METHODOLOGY AND RESULTS: Twenty-one BG strains have been characterized using the 16S rRNA and the gyrB gene-based sequence approach in the present study. The gyrB gene-based phylogenetic analysis resulted in geographic region-specific clustering of the BG isolates. The virulence screening of twenty-one BG strains by inoculating the pathogenic bacterial suspension of 1 × 10-8 cfu/ml at the booting stage (55 DAT) revealed the variation in the disease severity and the grain yield of rice plants. The most virulent BG1 strain resulted in the highest disease incidence (82.11%) and lowest grain yield (11.12 g/plant), and the least virulent BG10 strain resulted in lowest disease incidence of 18.94% and highest grain yield (24.62 g/plant). In vitro evaluation of various biocontrol agents and nano copper at different concentrations by agar well diffusion method revealed that nano copper at 1000 mg/L inhibited the colony growth of B. glumae. Under net house conditions, nano copper at 1000 mg/L reduced the disease severity to 21.23% and increased the grain yield by 20.91% (31.76 g per plant) compared to the positive control (COC 0.25% + streptomycin 200 ppm). Remarkably, pre-inoculation with nano copper at 1000 mg/L followed by challenge inoculation with B. glumae enhanced the activity of enzymatic antioxidants viz., Phenyl ammonia-lyase (PAL), Polyphenol oxidase (PPO) and Peroxidase (POX) and non-enzymatic antioxidant phenol. Additionally, we observed a substantial transcript level upregulation of six defense-related genes to several folds viz., OsPR2, OsPR5, OsWRKY71, OsPAL1, OsAPX1, and OsPPO1 in comparison to the pathogen control and healthy control. CONCLUSIONS: Overall, our study provides valuable insights into the potential and practical application of nano copper for the mitigation of bacterial panicle blight, offering promising prospects for commercial utilization in disease management.

Manufacturing of Aluminum Nano-Composites Reinforced with Nano-Copper and High Graphene Ratios Using Hot Pressing Technique.

In this study, the nano-aluminum powder was reinforced with a hybrid of copper and graphene nanoplatelets (GNPs). The ratios of GNPs were 0 wt%, 0.4 wt%, 0.6 wt%, 1.2 wt% and 1.8 wt%. To avoid the reaction between aluminum and graphene and, consequently, the formation of aluminum carbide, the GNP was first metalized with 5 wt% Ag and then coated with the predetermined 15 wt% Cu by the electroless coating process. In addition, the coating process was performed to improve the poor wettability between metal and ceramic. The Al/(GNPs-Ag)Cu nanocomposites with a high relative density of 99.9% were successfully prepared by the powder hot-pressing techniques. The effects of (GNPs/Ag) and Cu on the microstructure, density, hardness, and compressive strength of the Al-Cu nanocomposite were studied. As a result of agitating the GNPs during the cleaning and silver and Cu-plating, a homogeneous distribution was achieved. Some layers formed nano-tubes. The Al4C3 phase was not detected due to coating GNPs with Cu. The Cu9Al4 intermetallic was formed during the sintering process. The homogeneous dispersion of Cu and different ratios of GNs, good adhesion, and the formation of the new Cu9Al4 intermetallic improved in hardness. The pure aluminum sample recorded 216.2 HV, whereas Al/Cu reinforced with 1.8 GNs recorded 328.42 HV with a 51.9% increment. The compressive stress of graphene samples was improved upon increasing the GNPs contents. The Al-Cu/1.8 GNs sample recorded 266.99 MPa.

Nano-copper ions assembled cellulose-based composite with antibacterial activity for biodegradable personal protective mask.

The current SARS-CoV-2 pandemic has resulted in the widespread use of personal protective equipment, particularly face masks. However, the use of commercial disposable face masks puts great pressure on the environment. In this study, nano-copper ions assembled cotton fabric used in face masks to impart antibacterial activity has been discussed. To produce the nanocomposite, the cotton fabric was modified by sodium chloroacetate after its mercerization, and assembled with bactericidal nano-copper ions (about 10.61 mg·g-1) through electrostatic adsorption. It demonstrated excellent antibacterial activity against Staphylococcus aureus and Escherichia coli because the gaps between fibers in the cotton fabric allow the nano-copper ions to be fully released. Moreover, the antibacterial efficiency was maintained even after 50 washing cycles. Furthermore, the face mask constructed with this novel nanocomposite upper layer exhibited a high particle filtration efficiency (96.08% ± 0.91%) without compromising the air permeability (28.9 min·L-1). This green, economical, facile, and scalable process of depositing nano-copper ions onto modified cotton fibric has great potential to reduce disease transmission, resource consumption, and environmental impact of waste, while also expanding the range of protective fabrics.

Nano-copper Enhances Gene Regulation of Non-specific Immunity and Antioxidative Status of Fish Reared Under Multiple Stresses.

Arsenic pollution, water temperature, and pH are the major concern for aquaculture. Moreover, the aim of the present investigation was to delineate the role of nano-copper (Cu-NPs) in the mitigation of arsenic toxicity, high temperature (34 °C) and low pH (6.5) stress on Pangasianodon hypophthalmus. Four isonitrogenous and isocaloric experimental diets of Cu-NPs at 0, 1.0, 1.5 and 2.0 mg kg-1 were formulated and prepared. Arsenic pollution, low pH and high temperature stress significantly reduced the anti-oxidative status (super oxide dismutase, catalase, glutathione peroxidase and glutathione-s-transferase), lipid peroxidation, total anti-oxidative capacity and lipid profiling (cholesterol, total lipid, phospholipid, very low-density lipoprotein and triglyceride). Further, the supplementation of Cu-NPs at 1.5 and 1.0 mg kg-1 diets noticeably improve the anti-oxidant status and capacity. The stressors groups (As + pH + T, As + T and As) significantly reduced fish immunity viz. albumin, globulin, total protein, albumin globulin ratio (A:G ratio), myeloperoxidase, respiratory burst activities, tumor necrosis factor, total immunoglobulin, and interleukin. Whereas supplementation of Cu-NPs at 1.5 and 1.0 mg kg-1 diets improved the immunity of the fish reared under multiple stresses (As + pH + T). Tail DNA %, DNA damage-inducible protein (DDIP) and inducible nitric oxide (iNOS) synthase gene expression were significantly enhanced with exposure to arsenic, low pH and high temperature but supplementation of Cu-NPs protects the tissues against DNA damage and improved the gene expression of iNOS and DDIP. Cu-NPs at 1.5 and 1.0 mg kg-1 diets significantly enhanced the body weight gain %, protein efficiency ratio, specific growth rate, daily growth index, relative feed intake and reduced the feed conversion ratio. Whereas, the growth-related gene expression such as myostatin (MYST), somatostatin (SMT) was downregulated by Cu supplementation and upregulated the gene expression of growth hormone regulator 1 and ß (GHR1 and GHR ß) and growth hormone (GH) gene in fish. Dietary Cu-NPs supplementation protects the fish against bacterial infection and enhances arsenic detoxification in different tissues. The present investigation revealed that supplementation of Cu-NPs at 1.5 and 1.0 mg kg-1 diet has the potential to mitigate multiple stress (As + pH + T) in fish.

Adsorption of dyestuff by nano copper oxide coated alkali metakaoline geopolymer in monolith and powder forms: Kinetics, isotherms and microstructural analysis.

To remove contaminants and pollutants from wastewater systems, adsorbents are widely used. Geopolymers offer a convenient alternative as adsorbents in the wastewater treatment system as they are low-cost, environmentally friendly, and safer. A new adsorbent material prepared by coating nano copper oxide on the surface of alkali-activated metakaolin showed a higher ability to remove methylene blue (MB) dye from wastewater, thus making them attractive in dye removal applications. First, nano copper oxide was prepared by sol gel method and metakaolin geopolymer was produced using sodium silicate solution having a Ms value of 1.1 (M). Afterwards, nano copper oxide (MC) was coated on the surface of the geopolymer. The ability of MB dye to bind to both pristine (Mp, MCp) and powder forms (Mpr, MCpr) of the geopolymer was evaluated. X-ray diffraction revealed that the halo found at 27.40°-31.077° (2θvalue) in both samples related to amorphous gel's composition and the major peaks of copper oxide in MCpr were sited at a 2θ value of 35.45° and 38.88°.The dye removal efficiency can be inferred from the increased adsorption capacity of 11.9 mg/g (Mp) and 14.4 mg/g (MCp) for the monolith form and 81.43 mg/g (Mpr) and 87.82 mg/g (MCpr) for the powder form. The adsorption of reused active sites was 73% for Mpr and 83% for MCpr up to the fifth cycle after regeneration by heat treatment at 400 °C. The models that best suited the adsorption data were pseudo-second-order and Freundlich isotherms, which indicated possible chemisorption with intra-particle diffusion. Furthermore, the binding energy is shifted to lower value in XPS spectra due to dye adsorption arising from electrostatic attraction. A higher electron density is formed due to interaction with an equal contribution of silanol Si-O-H and Si-O-Na/Cu(O1s). The adsorbents are effective over a wide pH range and their improved recycling capability increases their applications for a wide range of uses.

Desulfurization of Cu-Fe Alloy Obtained from Copper Slag and the Effect on Form of Copper in Alloy.

In order to realize the high-value utilization of copper slag, a process for preparing Cu-Fe alloy through the reduction of copper slag is proposed. The sulfur in the alloy exists in the form of matte inclusions, which is different from sulfur in molten iron. The reaction of CaO with Cu2S is difficult. It is necessary to add a reducing agent to promote desulfurization. To avoid the introduction of other elements, Fe-Mn and CaC2 additions were used as desulfurizers for the desulfurization of Cu-Fe alloy. The thermodynamics of the desulfurization reaction were calculated and the experimental process was studied. It was found that the Gibbs free energy of desulfurization reactions was negative for Fe-Mn and that CaC2 can reduce the sulfur in the alloy to 0.0013% and 0.0079%, respectively. The desulfurization process affected the shape of copper in the alloy. Part of copper in this alloy exists in the form of nano-copper spheres, and the size of the spheres is found to increase after desulfurization. Reducing agents can facilitate the desulfurization process of stable sulfides.

Bacterial Biofilm Formation on Nano-Copper Added PLA Suited for 3D Printed Face Masks.

The COVID-19 Pandemic leads to an increased worldwide demand for personal protection equipment in the medical field, such as face masks. New approaches to satisfy this demand have been developed, and one example is the use of 3D printing face masks. The reusable 3D printed mask may also have a positive effect on the environment due to decreased littering. However, the microbial load on the 3D printed objects is often disregarded. Here we analyze the biofilm formation of Pseudomonas aeruginosa, Staphylococcus aureus, and Escherichia coli on suspected antimicrobial Plactive™ PLA 3D printing filaments and non-antimicrobial Giantarm™ PLA. To characterize the biofilm-forming potential scanning electron microscopy (SEM), Confocal scanning electron microscopy (CLSM) and colony-forming unit assays (CFU) were performed. Attached cells could be observed on all tested 3D printing materials. Gram-negative strains P. aeruginosa and E. coli reveal a strong uniform growth independent of the tested 3D filament (for P. aeruginosa even with stressed induced growth reaction by Plactive™). Only Gram-positive S. aureus shows strong growth reduction on Plactive™. These results suggest that the postulated antimicrobial Plactive™ PLA does not affect Gram-negative bacteria species. These results indicate that reusable masks, while better for our environment, may pose another health risk.

Autophagy and apoptosis mediated nano-copper-induced testicular damage.

Nano-copper has been increasingly employed in various products. In previous studies, we showed that nano-copper caused damage in the rat testis, but it remains unclear whether the toxic reaction can affect the reproductive function. In this study, following 28 d of exposure to nano-copper at a dose of 44, 88, and 175 mg/kg/day, there was a decrease in sperm quality, fructose content, and the secretion of sex hormones. Nano-copper also increased the level of oxidative stress, sperm malformation rate, and induced abnormal structural changes in testicular tissue. Moreover, Nano-copper upregulated the expression of apoptosis-related protein Bax and autophagy-related protein Beclin, and downregulated the expression of Bcl2 and p62. Furthermore, nano-copper (175 mg/kg) downregulated the protein expression of AMPK, p-AKT, mTOR, p-mTOR, p-4E-BP1, p70S6K, and p-p70S6K, and upregulated the protein expression of p-AMPK. Therefore, nano-copper induced damage in testicular tissues and spermatogenesis is highly related to cell apoptosis and autophagy by regulating the Akt/mTOR signaling pathway. In summary, excess exposure to nano-copper may induce testicular apoptosis and autophagy through AKT/mTOR signaling pathways, and damage the reproductive system in adult males, which is associated with oxidative stress in the testes.

Hot-melt extruded copper sulfate affects the growth performance, meat quality, and copper bioavailability of broiler chickens.

OBJECTIVE: This study was conducted to evaluate the effects of the supplementation of diets of broiler chickens with hot-melt extruded CuSO4 (HME-Cu) on their growth performance, nutrient digestibility, gut microbiota, small intestinal morphology, meat quality, and copper (Cu) bioavailability. METHODS: A total of 225 broilers (Ross 308), one-day old and initial weight 39.14 g, were weighed and distributed between 15 cages (15 birds per cage) in a completely randomized experimental design with 3 treatments (diets) and 5 replicates per treatment. Cages were allotted to three treatments including control (without supplemental Cu), IN-Cu (16 mg/kg of CuSO4), and HME-Cu (16 mg/kg of HME processed CuSO4). RESULTS: The HME-Cu treatment tended to increase the overall body weight gain (p<0.10). The apparent digestibility of Cu was increased by supplementation of HME-Cu at phase 2 (p<0.05). The Escherichia coli count in cecum tended to decrease with the supplementation with Cu (p<0.10). In addition, the HME-Cu treatment had a higher pH of breast meat than the control and IN-Cu treatments (p<0.05). Significant increases in the cooking loss, water-holding capacity, and lightness in the breast were observed in the HME-Cu treatment compared to the control (p<0.05). The Cu content of excreta increased with the Cu supplementation (p<0.05). The concentration of excreta Cu in broilers was decreased in the HME-Cu compared to the IN-Cu in phase 2 (p<0.05). The Cu concentration in the liver was increased with the HME-Cu supplementation, compared with the control diets (p<0.05). CONCLUSION: This study showed that HME-Cu supplementation at the requirement level (16 mg/kg diets) in broiler diets did not affect the growth performance and the physiological function of Cu in broilers. However, supplementation of Cu in HME form improved the meat quality and the bioavailability of Cu.

Effects of Nano-copper Oxide on Antioxidant Function of Copper-Deficient Kazakh Sheep.

Kazakh sheep are vital to the production system of the Barkol prairie. The purpose of this study was to determine the effect of nano-copper oxide (Nano-Cu2O) on the antioxidant system of Cu-deficient Kazakh sheep in the Barkol prairie in Xinjiang, China. We analyzed mineral contents in soil, forage, and animal tissues. Blood parameters were also measured at the same time. The results showed that compared with healthy grassland, the Cu content in the soil and forage in Cu-deficient pastures was significantly lower than that in healthy grassland (P < 0.01). The Cu content in the blood, wool, and liver of Cu-deficient Kazakh sheep was significantly lower than that of healthy animals (P < 0.01). After Kazakh sheep were supplemented with Nano-Cu2O or CuSO4, the blood Cu concentration increased significantly (P < 0.01). From the 5th day, the Cu content of the Nano-Cu2O group was significantly higher than that of the CuSO4 group. The levels of hemoglobin (Hb), erythrocyte count (RBC), and packed cell volume (PCV) in the two experimental groups were significantly higher than those in Cu-deficient Kazakh sheep (P < 0.01). Compared with Cu-deficient Kazakh sheep, the serum ceruloplasmin (Cp) level of the two experimental groups increased significantly (P < 0.01), while the serum lactate dehydrogenase (LDH), alkaline phosphatase (AKP), aspartate aminotransferase (AST), and alanine aminotransferase (ALT) decreased significantly (P < 0.01). Compared with Cu-deficient Kazakh sheep, the activities of serum superoxide dismutase (SOD), glutathione peroxidase (GSH-Px), catalase (CAT), and total antioxidant capacity (T-AOC) in Nano-Cu2O and CuSO4 groups increased significantly (P < 0.01), while the level of serum malondialdehyde (MDA) decreased significantly (P < 0.01). Therefore, Nano-Cu2O could not only significantly increase the Cu content in the blood of Cu-deficient Kazakh sheep, but also greatly improve the antioxidant capacity.

The effects of copper ions and copper nanomaterials on the output of amino acids from marine microalgae.

In this study, the marine microalgae Skeletonema costatum and Nitzschia closterium were exposed to different forms of copper, such as a metal salt (Cu2+), a nano-metal (nano-Cu), and nano-metal oxide (nano-CuO). During a 96-h exposure to nanoparticles (NPs) and salt, the cell number, Cu2+ concentration in the culture medium, morphology, and intracellular amino acids were measured to assess the toxicity of the copper materials and the toxicity mechanism of the NPs. As results, the toxicity of Cu2+, nano-Cu, and nano-CuO to marine phytoplankton decreased in order. The EC50 values of Cu2+ and nano-Cu for S. costatum and N. closterium ranged from 0.356 to 0.991 mg/L and 0.663 to 2.455 mg/L, respectively. Nano-Cu inhibits the growth of marine phytoplankton by releasing Cu2+; however, nano-CuO is harmful to microalgae because of the effect of NPs. The secretion of extracellular polymeric substances by microalgae could also affect the toxicity of nano-Cu and nano-CuO to microalgae. S. costatum was more sensitive to copper than N. closterium. Cu2+, nano-Cu, and nano-CuO all reduced per-cell amino acids and the total output of algae-derived amino acids by affecting the growth of the phytoplankton. This study helps to understand the risk assessment of nano-Cu and nano-CuO to marine microalgae.

Enhanced photocatalytic performance of visible-light-driven CuOx/TiO2-x for degradation of gaseous formaldehyde: Roles of oxygen vacancies and nano copper oxides.

Photocatalysis is an effective method for the removal of formaldehyde (HCHO), and high-efficiency visible-light-driven photocatalysts were urgently required. Herein, oxygen vacancies (OVs) and nano copper oxides (CuOx) synergistically modified TiO2 (CuOx/TiO2-x) photocatalysts were synthesized by one-step hydrothermal followed by impregnation method. The photocatalytic decomposition of HCHO reached 100% at initial concentration of 180 ppm under relative humidity (RH) = 60% by 0.1g CuOx/TiO2-x in 150 min visible light irradiation. Characterization results explored the complementary effect of OVs and CuOx systematically. The OVs increased the separation efficiency of photogenerated charge carriers and act as adsorption/active sites in HCHO photocatalytic oxidation. The moisture and O2 were adsorbed and actived by OVs to generate reactive oxygen species (ROS). After doped CuOx on the surface of TiO2-x, the photoexcited electrons in Cu2O could transfer to the conduction band (CB) of TiO2-x and the photoexcited electrons of TiO2-x could be captured by Cu nanoparticles. Therefore, more ROS were generated due to the synergistic effect of OVs and CuOx. The In-situ Fourier transform infrared (in-situ FTIR) measurements show the hydroxyl radical (•OH) was the dominant radical in HCHO photocatalytic oxidation, while •O2- could also upgrade the photodegradation efficiency of HCHO. Furthermore, the stability tests showed the degradation efficiency of HCHO still reached 90% after five recycles, indicating that CuOx/TiO2-x nanocomposites displayed a stable and high photoactivity in volatile organic compounds (VOCs) decomposition.

Bactericidal and Fungistatic Properties of LDPE Modified with a Biocide Containing Metal Nanoparticles.

The aim of this study was to ascertain whether the combined action of metal nanoparticles (silver, copper, zinc oxide, iron oxide) would ensure the appropriate biocidal properties oflow-density polyethylene (LDPE) against pathogenic microorganisms. According to the research hypothesis, appropriately selected concentrations of the applied metal nanoparticles allow for a high level of biocidal activity of polymeric materials against both model and pathogenic bacterial strains (Escherichia coli, Staphylococcus aureus, Pseudomonas aeruginosa, Legionella pneumophila, Salmonella enterica subsp. enterica) and fungi (Aspergillus brasiliensis, Saccharomyces cerevisiae, Candida albicans, Penicilium expansum), whilst ensuring the safety of use due to the lack of migration of particles to the surrounding environment. Studies have shown that adding 4% of a biocide containing Ag, Cu, ZnO, and Fe2O3 nanoparticles is the most optimal solution to reduce the number of S. aureus, S. enterica and P. aeruginosa by over 99%. The lowest effectiveness was observed against L. pneumophila bacteria. As for E. coli, a higher biocide content did not significantly increase the antibacterial activity. The results showed a high efficiency of the applied biocide at a concentration of 2% against fungal strains. The high efficiency of the obtained biocidal results was influenced by the uniform dispersion of nanoparticles in the material and their low degree of agglomeration. Furthermore, a slight migration of components to the environment is the basis for further research in the field of the application of the developed materials in industry.

Autophagy was activated against the damages of placentas caused by nano-copper oral exposure.

Nano-copper (nano-Cu) is widely used in the pharmaceutical field as well as a feed additive for animals owing to its unique physicochemical characteristics and bioactivities. In our previous study, nano-Cu was found to hamper fetal development; however, the toxicity of nano-Cu and its effects in placental function have not been elucidated. Therefore, we investigated the toxic effects of nano-Cu using rat placenta. Pregnant Sprague-Dawley rats were orally exposed to different copper sources from the third day of gestation (GD 3) to GD 18. We found that nano-Cu (180 mg/kg) and CuCl2.2 H2O increased the accumulation of copper. Besides, nano-Cu and CuCl2.2 H2O disrupted the placental morphology and induced oxidative stress. Micro-copper (micro-Cu) caused similar toxicity in the placenta, but its effects were weaker than that of nano-Cu and CuCl2.2 H2O. In addition, exposure to nano-Cu (180 mg/kg) and CuCl2.2 H2O induced inflammation in the rat placenta. Furthermore, nano-Cu, micro-Cu, and CuCl2.2 H2O upregulated the expression of the autophagy-related proteins, Beclin-1 and LC3 II/ LC3 I, and downregulated that of p62. Moreover, nano-Cu, micro-Cu, and CuCl2.2 H2O downregulated the protein expression of PI3K, p-AKT/AKT, and p-mTOR/mTOR in rat placentas, whereas the protein expression of p-AMPK/AMPK was upregulated. Taken together, our data indicated that prenatal exposure to nano-Cu induced autophagy via the PI3K/AKT/mTOR and AMPK/mTOR pathways, which associated with oxidative stress and inflammation in rat placenta.

Effects of hot-melt extruded nano-copper on the Cu bioavailability and growth of broiler chickens.

This study was aimed to investigate the Cu bioavailability, growth response, digestibility of nutrients, and blood metabolites of broiler chicks fed CuSO4 in nano or common forms. A total of 720 broiler chickens were distributed between eight treatments according to a completely randomized design. There were 8 treatments and 6 replicates in each treatment with 15 birds/replicate. The treatments were divided into common copper sulfate at the doses of 16 ppm, 40 ppm, 80 ppm, and 120 ppm (INO) and hot-melt extruded copper sulfate at the doses of 16 ppm, 40 ppm, 80 ppm, and 120 ppm (HME-Cu). The experiment was operated for 35 days in 2 phases (phase 1, d 0 to 14; and phase 2, d 15 to 35). No significant differences were shown in growth performance, feed intake, FCR, and nutrient digestibility among the treatments. The concentration of Cu in the serum was increased in the HME-Cu broilers compared with the INO broilers at phase 2. A linear increase was observed in the concentration of Cu in the liver in broilers fed INO diets, however, no significant differences were observed by the supplementation of HME-Cu levels. The linear increase was detected in the content of Cu in excreta in the INO and HME-Cu treatments by increasing the dietary Cu content. The HME-Cu treatments showed a lower Cu concentration in the excreta compared with the INO treatments. The higher bioavailability of Cu in HME form can decrease the recommended dose of Cu in broiler diets.

Recent Advancement of Emerging Nano Copper-Based Printable Flexible Hybrid Electronics.

Printed copper materials have been attracting significant attention prominently due to their electric, mechanical, and thermal properties. The emerging copper-based flexible electronics and energy-critical applications rely on the control of electric conductivity, current-carrying capacity, and reliability of copper nanostructures and their printable ink materials. In this review, we describe the growth of copper nanostructures as the building blocks for printable ink materials on which a variety of conductive features can be additively manufactured to achieve high electric conductivity and stability. Accordingly, the copper-based flexible hybrid electronics and energy-critical devices printed by different printing techniques are reviewed for emerging applications.

Thermal interface material with graphene enhanced sintered copper for high temperature power electronics.

Sintered nano-copper is becoming a promising candidate as thermal interface material (TIM) for die attaching in high power electronics. It exhibits much higher thermal conductivity and operating temperature than conventional TIMs based on polymer and solder joints, and higher electromigration resistance and lower cost than sintered nano-silver TIM. However, the performance of existing sintered nano-copper is lower than expected because of high porosity resulted from poor sintering of copper particles with oxide shell. Here we demonstrate a method of improving the thermal conductivity of sintered copper by addition of graphene/Cu-CuxO with controllable diameter of ∼163 nm. The measured thermal conductivity of the sintered composite TIM is enhanced by up to 123.5% compared with that of sintered pure copper. It can be understood as a result of the formation of graphene heat transfer network in sintered TIM. In addition, the C-O-Cu bonds formed at the interface between graphene and copper nanoparticles are critical for improving thermal performance as well as electrical and mechanical performance of the TIM. The developed TIM can be widely used in high power electronic packaging especially for high temperature applications, including IGBT, SiC and GaN power devices.