Adsorption dynamics of heavy oil droplets on silica: Effect of asphaltene anionic carboxylic.

Understanding the adsorption behavior of asphaltene molecules on the surfaces of oil reservoir solids is essential for optimizing oil recovery processes. This study employed molecular dynamics simulations to investigate the adsorption behavior of oil droplets composed of charged and neutral asphaltenes on silica surfaces. The results revealed that oil droplet containing anionic asphaltene molecules were more likely to adsorb onto silica surfaces and exhibited greater resistance to detachment compared to oil droplet containing neutral asphaltene molecules. Specifically, anionic asphaltene molecules tended to accumulate at the oil-water-silica interface, whereas neutral asphaltene molecules primarily adsorbed near the oil-water interface. These findings provide valuable insights into the differing adsorption dynamics of charged and neutral asphaltene molecules on silica surfaces.

Enhanced removal of nano-oil droplets utilizing polysilicate aluminum ferric (PSAF): Leveraging bridging and non-polar surface advantages.

Hydraulic oil leaks during mechanical maintenance, resulting in flushing wastewater contaminated with dispersed nano-oil droplets. In this study, 75 mg L-1 of polysilicate aluminum ferric (PSAF) was stirred at 350 rpm and the optimal chemical oxygen demand (COD) removal was 71%. The increase of PSAF led to more hydrolysis of Fe, and 1,175 cm-1 hydroxyl bridged with negative oil droplets. At the same molar concentration, PSAF hydrolyzes cationic metals more rapidly than polymeric aluminum chloride (PAC). PSAF forms flocs of smaller complex structures with greater bridging. The Al-O and Si-O peaks occurred at 611 and 1,138 cm-1, indicating the formation of Si-O-Fe and Si-O-Al bonds on the flocs surface. Higher stirring speeds did not change the free energy of the flocs surface γTot, mainly because the decrease in the van der Waals force (γLW) offset the increase of Lewis acid-base force (γAB). Preserving the non-polar surface, in summary, owing to its bridging abilities and affinity for non-polar surfaces, PSAF demonstrates superior efficiency over PAC in capturing and removing oil droplets.

Water-in-oil droplet-mediated method for detecting and isolating infectious bacteriophage particles via fluorescent staining.

Bacteriophages are the most abundant entities on Earth. In contrast with the number of phages considered to be in existence, current phage isolation and screening methods lack throughput. Droplet microfluidic technology has been established as a platform for high-throughput screening of biological and biochemical components. In this study, we developed a proof-of-concept method for isolating phages using water-in-oil droplets (droplets) as individual chambers for phage propagation and co-cultivating T2 phage and their host cell Escherichia coli within droplets. Liquid cultivation of microbes will facilitate the use of microbes that cannot grow on or degrade agar as host cells, ultimately resulting in the acquisition of phages that infect less known bacterial cells. The compartmentalizing characteristic of droplets and the use of a fluorescent dye to stain phages simultaneously enabled the enumeration and isolation of viable phage particles. We successfully recultivated the phages after simultaneously segregating single phage particles into droplets and inoculating them with their host cells within droplets. By recovering individual droplets into 96-well plates, we were able to isolate phage clones derived from single phage particles. The success rate for phage recovery was 35.7%. This study lays the building foundations for techniques yet to be developed that will involve the isolation and rupturing of droplets and provides a robust method for phage enumeration and isolation.

Simulating dispersion of oils from a subsea release comparing mechanical and chemically enhanced dispersion - An experimental study of the influence of oil properties.

The main objective with subsea mechanical dispersion (SSMD) is to influence the fate of an oil spill in the marine environment by significantly reducing oil droplet sizes from subsea release of oil. Earlier studies have indicated that the capability of SSMD to reduce oil droplet sizes is comparable to subsea dispersant injection (SSDI). Earlier testing of SSMD has mainly used a low viscus paraffinic oil. Focus for this study was to study SSMD and SSDI effectiveness using five oil types spanning out a wide variation of relevant oil properties. Effectiveness was quantified as the reduction in oil droplet sizes measured by a Silhouette camera. Testing of the two technologies were completed in the same experiment on a simulated subsea release. The results show a variation in effectiveness for both technologies as a function of oil properties. SSMD and SSDI showed comparable effectiveness for all oils tested.

Hydrodynamic Treadmill Reveals Reduced Rising Speeds of Oil Droplets Deformed by Marine Bacteria.

In marine environments, microscopic droplets of oil can be transported over large distances in the water column. Bacterial growth on the droplets' surface can deform the oil-water interface to generate complex shapes and significantly enlarge droplets. Understanding the fate of spilled oil droplets requires bridging these length scales and determining how microscale processes affect the large-scale transport of oil. Here, we describe an experimental setup, the hydrodynamic treadmill, developed to keep rising oil droplets stationary in the lab frame for continuous and direct observation. Oil droplets with radii 10 < R < 100 µm were colonized and deformed by bacteria over several days before their effective rising speeds were measured. The rising speeds of deformed droplets were significantly slower than those of droplets without bacteria. This decrease in rising speed is understood by an increase in drag force and a decrease in buoyancy as a result of bio-aggregate formation at the droplet surface. Additionally, we found sinking bio-aggregate particles of oil and bacterial biofilms and quantified their composition using fluorescence microscopy. Our experiments can be adapted to further study the interactions between oil droplets and marine organisms and could significantly improve our understanding of the transport of hydrocarbons and complex aggregates.

Emission and purification of evaporated-condensed oil droplets affected by condensation nuclei during machining.

Fine oil droplets emitted by evaporation-condensation during machining are typical indoor air contaminants. Airborne particles can act as condensation nuclei, facilitating the condensation of oil vapor. The physical properties of these resultant droplets significantly affect their purification efficiency. Herein, this study aimed to elucidate the emission characteristics of oil droplets formed by evaporation-condensation affected by condensation nuclei and the purification efficiency of intense field dielectric (IFD) technology for the droplets under varying airflow velocities. Results show that the removal of condensation nuclei can effectively reduce the mass of evaporated-condensed oil droplets, and the increment in the mass of oil droplets reached 1.7 times the increment in the mass of condensation nuclei. It was more effective to reduce the mass of oil droplets by removing large condensation nuclei and decreasing the amount of evaporated soluble oil, as compared to removing smaller condensation nuclei or using straight oil. Condensation nuclei mainly contributed to the generation of oil droplets below 5 µm. For droplet diameters of 0.3-5.0 µm and airflow velocities of 0.5-2.0 m/s, the purification efficiency was within the 84-96% range. The purification efficiency of the IFD purifier for oil droplets could be improved either by increasing the size of the oil droplets or by reducing the airflow velocity.

Reducing oil droplet sizes from a subsea oil and gas release by water jetting a laboratory study performed at different scales.

The main objective of subsea mechanical dispersion (SSMD) is to reduce the oil droplet sizes from a subsea oil release, thereby influencing the fate and behaviour of the released oil in the marine environment. Subsea water jetting was identified as a promising method for SSMD and imply that a water jet is used to reduce the particle size of the oil droplets initially formed from the subsea release. This paper presents the main findings from a study including small-scale testing in a pressurised tank, via laboratory basin testing, to large-scale outdoor basin testing. The effectiveness of SSMD increases with the scale of the experiments. From a five-fold reduction in droplet sizes for small-scale experiments to more than ten-fold for large-scale experiments. The technology is ready for full-scale prototyping and field testing. Large-scale experiments performed at Ohmsett indicate that SSMD could be comparable to subsea dispersant injection (SSDI) in reducing oil droplet sizes.

Combined effects of chemical dispersant and suspended minerals on the dispersion process of spilled oil.

The dispersion process of spilled oil is an important concern for the effective disposal of oil spills. The dispersed oil concentration and oil droplets size distribution were studied through a wave tank test under the application of chemical dispersant and suspended minerals. The results indicated that dispersant and minerals increased the dispersed oil concentration and the effect of dispersant was more significant, and they had a synergistic effect on oil dispersion. When dispersant and minerals were applied together, the volume mean diameter of oil droplets decreased in the first 30 min, then increased and reached a maximum value at 90-120 min, and decreased again. Moreover, suspended minerals could inhibit the coalescence of oil droplets. This study can afford data support for oil spill emergency response that occurs in inshore or estuaries.

Surface interaction mechanisms of air bubbles, asphaltenes and oil drops in aqueous solutions with implications for interfacial engineering processes.

HYPOTHESIS: Surface interactions of bubbles and oil with interface-active species like asphaltenes influence many interfacial phenomena in various engineering processes. It holds both fundamental and practical significance to quantitatively characterize these interactions. EXPERIMENTS: The surface forces of air bubbles, asphaltenes and asphaltenes-toluene droplets in various aqueous solutions have been quantified using an integrated thin film drainage apparatus and an atomic force microscope coupled with bubble probe. The effects of asphaltenes concentration, pH, salinity, Ca2+ ions and surfactants have been examined. FINDINGS: Hydrophobic interaction drives attachment of bubbles and asphaltenes surfaces or oil droplets under high salinity condition. Increasing asphaltenes concentration in oil droplets enhances their hydrophobic attraction with bubbles due to strengthened asphaltenes adsorption and aggregation at oil-water interface. Increasing pH weakens the hydrophobic interaction as oil surfaces become more negatively charged and less hydrophobic. Under low salinity condition, strong electrical double layer and van der Waals repulsion inhibits the bubble-oil droplet contact. Introducing Ca2+ ions and surfactants leads to strong steric repulsion, preventing bubble-oil contact. This research has advanced our mechanistic understanding of how bubbles and oil droplets interact in aqueous systems and offers useful insights to modulate such interactions in oil production, water treatment and other interfacial processes.

Investigation on the emulsification mechanism in aqueous enzymatic extraction of edible oil from Schizochytrium sp.

BACKGROUND: The interaction between emulsified substances and lipids generates an emulsification system during the extraction of microalgae edible oil by aqueous enzymatic method. This study aimed to resolve the dynamics of interfacial protein adsorption during the extraction of microalgae oil at different enzymatic times and the effect on the stability of the interfacial membrane formed by the proteins based on interfacial effects. RESULTS: At 1.5 h of enzymatic hydrolysis, the molecular weights of the proteins/peptides were all below 35 kD. In addition, the protein-peptide structure was loose, with the lowest number of disulfide bonds, peak surface hydrophobicity, the highest number of residues, and disordered lipid acyl arrangement. At the same time, the physical stability of the emulsion was the lowest, and the interfacial membrane rupture was distinct. On excessive enzymatic hydrolysis (at 3.0 h), a more uniform interfacial membrane was re-formed on the lipid surface. CONCLUSION: Protein is the main emulsifying substance in the emulsification system. The addition of protease affects the stability of the interfacial membrane formed by proteins. In addition, sufficient enzymatic hydrolysis (1.5 h) inhibited emulsification, while excessive enzymatic hydrolysis (3.0 h) promoted emulsification. © 2023 Society of Chemical Industry.

Magnetoreceptory Function of European Robin Retina: Electrophysiological and Morphological Non-Homogeneity.

The avian magnetic compass allows orientation during migration and is shown to function properly under short-wavelength but not long-wavelength visible light. Therefore, the magnetoreceptive system is assumed to be light- and wavelength-dependent and localized in the retina of the eye. Putative candidates for the role of primary magnetosensory molecules are the cryptochromes that are known to be expressed in the avian retina and must be able to interact with phototransduction proteins. Previously, we reported that in migratory birds change in magnetic field direction induces significant effects on electroretinogram amplitude in response to blue flashes, and such an effect was observed only in the nasal quadrant of the retina. Here, we report new electroretinographic, microscopic and microspectrophotometric data on European robins, confirming the magnetosensitivity of the retinal nasal quadrant after applying the background illumination. We hypothesized that magnetoreceptive distinction of this region may be related to its morphology and analyzed the retinal distribution and optical properties of oil droplets, the filtering structures within cones. We found that the nasal quadrant contains double cones with the most intensely colorized oil droplets compared to the rest of the retina, which may be related to its magnetosensory function.

Comparative Study on the Spreading Behavior of Oil Droplets over Teflon Substrates in Different Media Environments.

This paper comparatively investigated the spreading process of an oil droplet on the surface of highly hydrophobic solid (Teflon) in air and water media using a high-speed imaging technology, and analyzed their differences in spreading behavior from the perspective of empirical relations and energy conservation. Furthermore, the classical HD and MKT wetting models were applied to describe the oil droplet spreading dynamics to reveal the spreading mechanism of oil droplets on the Teflon in different media environments. Results showed that the entire spreading process of oil droplets on Teflon in air could be separated into three stages: the early linear fast spreading stage following θ(t)=θ0+kt , the intermediate exponential slow spreading stage obeying θ(t)=bt-3α, and the late spreading stage described by θ(t)=θeq+a×exp(-t/T). However, the dynamics behavior of dynamic contact angle during the oil droplet spreading on Teflon in water could be well described by these expressions, θ(t)=θ0+kt and θ(t)=θeq+a×exp(-t/T). Clearly, a significant difference in the oil droplet spreading behavior in air and water media was found, and the absence of the intermediate exponential spreading stage in the oil-water-Teflon system could be attributed to the difference in the dissipated energy of the system because the dissipation energy in the oil-water-solid system included not only the viscous dissipation energy of the boundary layer of oil droplet, but also that of the surrounding water which was not included in the dissipation energy of the oil-air-solid system. Moreover, the quantitative analysis of wetting models suggested that the MKT model could reasonably describe the late spreading dynamics of oil droplets (low TPCL velocities), while the HD model may be more suitable for describing the oil droplet spreading dynamics at the early and intermediate spreading stages (high TPCL velocities).

Effects of chemical dispersant on the surface properties of kaolin and aggregation with spilled oil.

After oil spills occur, dispersed oil droplets can collide with suspended particles in the water column to form the oil-mineral aggregate (OMA) and settle to the seafloor. However, only a few studies have concerned the effect of chemical dispersant on this process. In this paper, the mechanism by which dispersant affects the surface properties of kaolin and the viscosity and oil-seawater interfacial tension (IFTow) of Roncador crude oil were separately investigated by small-scale tests. The results indicated that the presence of dispersant impairs the zeta potential and enhances the hydrophobicity of kaolin. The viscosity of Roncador crude oil rose slightly as the dosage of dispersant increased, while IFTow decreased significantly. Furthermore, the oil dispersion and OMA formation at different dispersant-to-oil ratio (DOR) were evaluated in a wave tank. When DOR was less than 1:40, the effect of dispersant on the dispersion of spilled oil was not obvious. With the increasing DOR, the effect became more pronounced, and the adhesion between oil droplets and kaolin was inhibited. The size ratio between oil droplets and particles is the significant factor for OMA formation. The closer the oil-mineral size ratio is to 1, the more difficultly the OMA forms.

Cone distribution and visual resolution of the yellow-legged gull, Larus michahellis (Naumann, 1840).

The morphological characteristics of the yellow-legged gull's photoreceptors and cone distribution were studied using light and electron microscopy. In wholemount fresh retinas, five different coloured oil droplets located in the cone inner segments could be seen and characterized by colour, diameter and stratification. The photoreceptors were classified by comparing the fresh and fixed vertical sections under a light and electron microscope. Rods were easily distinguished from cones based on the outer segment morphology and the absence of oil droplets in their inner segments. Four types of single cones were associated with red, yellow, colourless and transparent oil droplets. Unequal double cones comprised a long principal member with a green oil droplet and an accessory short member containing a green microdroplet which was highly electron-dense under electron microscopy. The different types of oil droplets were counted from microphotographs of fresh retinal samples in 20 regions. The density, percentage and diameter of the oil droplets were determined. The results showed that central regions had the highest oil droplet density which decreased towards the retinal periphery in all quadrants. Moreover, the oil droplet density was higher in the dorsotemporal quadrant than in other retinal regions. The average density of the red oil droplets was highest in the central areas, whereas colourless oil droplets had the highest density throughout the retina. In contrast, transparent oil droplets had the lowest density across all the regions of the retina. Finally, the retinal resolution was 52.61 cycles/degree. It was calculated using the posterior nodal distance and the oil droplet diameter. The work concludes by discussing the significance of the relative proportion of different cone types across the retina.

The impact of exposure timing on embryo mortality and the partitioning of PAHs when cod eggs are exposed to dispersed and dissolved crude oil.

During sub-sea oil spills to the marine environment, oil droplets will rise towards the sea surface at a rate determined by their density and diameter as well as the vertical turbulence in the water. Micro-droplets (< 50 µm) are expected to have prolonged residence times in the water column. If present, pelagic fish eggs may thus be exposed to dispersed oil from subsurface oil spills for days, and the contribution of these micro-droplets to toxicity is not well known. The purpose of this work was to investigate to what extent timing of exposure and the presence of oil micro droplets affects PAH uptake and survival of pelagic Atlantic cod eggs. A single batch of eggs was separated in two groups and exposed to dispersions and corresponding water-soluble fraction at 3-7 days (Early exposure) and 9-13 days (Late exposure) post fertilization. Partitioning of PAHs between crude oil microdroplets, water and eggs was estimated as well as the contribution of oil droplets to PAH body residue and acute and delayed mortality. Timing of oil exposure clearly affects both the mortality rate and the timing of mortality. Even though the body residue of PAHs were lower when embryos were exposed in the later embryonic stage, mortality rate increased relative to the early exposure indicating that critical body residue threshold is stage specific. Although our results suggest that the dissolved fraction is the dominating driver for toxicity in cod embryos exposed to oil dispersions, crude oil micro droplets contribute to increased mortality as well.

Self-preserving mechanisms in motile oil droplets: a computational model of abiological self-preservation.

Recent empirical work has characterized motile oil droplets-small, self-propelled oil droplets whose active surface chemistry moves them through their aqueous environment. Previous work has evaluated in detail the fluid dynamics underlying the motility of these droplets. This paper introduces a new computational model that is used to evaluate the behaviour of these droplets as a form of viability-based adaptive self-preservation, whereby (i) the mechanism of motility causes motion towards the conditions beneficial to that mechanism's persistence; and (ii) the behaviour automatically adapts to compensate when the motility mechanism's ideal operating conditions change. The model simulates a motile oil droplet as a disc that moves through a two-dimensional spatial environment containing diffusing chemicals. The concentration of reactants on its surface change by way of chemical reactions, diffusion, Marangoni flow (the equilibriation of surface tension) and exchange with the droplet's local environment. Droplet motility is a by-product of Marangoni flow, similar to the motion-producing mechanism observed in the lab. We use the model to examine how the droplet's behaviour changes when its ideal operating conditions vary.

Formation by high power ultrasound of aggregated emulsions stabilised with milk protein concentrate (MPC70).

In this work, oil-in-water emulsions stabilised by milk protein concentrate (MPC70) were investigated. The MPC70 concentration was kept constant at 5% (close to the protein content found in skim milk) and the oil volume fraction was varied from 20 to 65%. Sonication was performed at 20 kHz and at a constant power of 14.4 W for a total emulsion volume of 10 mL. Under certain oil concentration (≥35%) and sonication times (≥3s) the emulsion aggregated and formed high-viscosity pseudo plastic materials. However, the viscosity behaviour of the emulsion made with 35% oil reverted to that of a liquid if sonicated for longer times (≥15 s). Confocal laser scanning microscopy showed clearly that the oil droplets are aggregated under the sonication conditions and oil concentrations indicated above. An attempt to explain this behaviour through a simple model based on the bridging of oil droplets by the MPC70 particles and, taking into account the oil droplet and MPC70 particle sizes as well as the oil volume fraction, was made. The model fails to describe in details the aggregation behaviour of these emulsions, likely due to the inhomogeneous protein layer, where both free caseins and casein micelles are adsorbed, and to the packing of the oil droplets at concentrations ≤55%. Nonetheless, this work demonstrates the potential of ultrasound processing for the formation of dairy emulsions with tailored textures.

Silicone Oil Droplets in the Schlemm's Canal: A Surprise during Prolene Hemi-gonioscopy-assisted Transluminal Trabeculotomy (Hemi-GATT).

AIM AND OBJECTIVE: To report a case with emulsified silicone oil (SO) droplets in the Schlemm's canal (SC), encountered during prolene hemi-gonioscopy-assisted transluminal trabeculotomy (hemi-GATT). BACKGROUND: In cases with a history of previous pars plana vitrectomy (PPV) with SO tamponade and then SO removal; glaucoma might occur secondary to the presence of emulsified SO droplets. Minimal invasive glaucoma surgeries targeting trabecular meshwork such as GATT surgery might be an ideal treatment option in these cases. CASE DESCRIPTION: A 57-year-old man presented with uncontrolled intraocular pressure (IOP) and topical anti-glaucoma drug intolerance in his left eye. The patient had a history of PPV with SO tamponade and then intravitreal SO removal 5 years ago. He had a history of Ahmed glaucoma valve (AGV) implantation 2 years ago for the treatment of secondary glaucoma but he was still using topical anti-glaucoma medication. However, IOP was measured as 17 in the left eye. Hemi-gonioscopy-assisted transluminal trabeculotomy was performed successfully to get the patient off medication. During the surgery, SC was full of SO droplets. CONCLUSION: The presence of SO droplets in the SC might contribute to the development of secondary glaucoma after PPV and SO removal. This might be another surgical indication for GATT surgery in these risky eyes. HOW TO CITE THIS ARTICLE: Aktas Z, Bölük CE, Gurelik G. Silicone Oil Droplets in the Schlemm's Canal: A Surprise during Prolene Hemi-gonioscopy-assisted Transluminal Trabeculotomy (Hemi-GATT). J Curr Glaucoma Pract 2021;15(1):40-43.

Negative Pressure Provides Simple and Stable Droplet Generation in a Flow-Focusing Microfluidic Device.

Droplet microfluidics is an extremely useful and powerful tool for industrial, environmental, and biotechnological applications, due to advantages such as the small volume of reagents required, ultrahigh-throughput, precise control, and independent manipulations of each droplet. For the generation of monodisperse water-in-oil droplets, usually T-junction and flow-focusing microfluidic devices connected to syringe pumps or pressure controllers are used. Here, we investigated droplet-generation regimes in a flow-focusing microfluidic device induced by the negative pressure in the outlet reservoir, generated by a low-cost mini diaphragm vacuum pump. During the study, we compared two ways of adjusting the negative pressure using a compact electro-pneumatic regulator and a manual airflow control valve. The results showed that both types of regulators are suitable for the stable generation of monodisperse droplets for at least 4 h, with variations in diameter less than 1 µm. Droplet diameters at high levels of negative pressure were mainly determined by the hydrodynamic resistances of the inlet microchannels, although the absolute pressure value defined the generation frequency; however, the electro-pneumatic regulator is preferable and convenient for the accurate control of the pressure by an external electric signal, providing more stable pressure, and a wide range of droplet diameters and generation frequencies. The method of droplet generation suggested here is a simple, stable, reliable, and portable way of high-throughput production of relatively large volumes of monodisperse emulsions for biomedical applications.

Avian color expression and perception: is there a carotenoid link?

Carotenoids color many of the red, orange and yellow ornaments of birds and also shape avian vision. The carotenoid-pigmented oil droplets in cone photoreceptors filter incoming light and are predicted to aid in color discrimination. Carotenoid use in both avian coloration and color vision raises an intriguing question: is the evolution of visual signals and signal perception linked through these pigments? Here, we explore the genetic, physiological and functional connections between these traits. Carotenoid color and droplet pigmentation share common mechanisms of metabolic conversion and are both affected by diet and immune system challenges. Yet, the time scale and magnitude of these effects differ greatly between plumage and the visual system. Recent observations suggest a link between retinal carotenoid levels and color discrimination performance, but the mechanisms underlying these associations remain unclear. Therefore, we performed a modeling exercise to ask whether and how changes in droplet carotenoid content could alter the perception of carotenoid-based plumage. This exercise revealed that changing oil droplet carotenoid concentration does not substantially affect the discrimination of carotenoid-based colors, but might change how reliably a receiver can predict the carotenoid content of an ornament. These findings suggest that, if present, a carotenoid link between signal and perception is subtle. Deconstructing this relationship will require a deeper understanding of avian visual perception and the mechanisms of color production. We highlight several areas where we see opportunities to gain new insights, including comparative genomic studies of shared mechanisms of carotenoid processing and alternative approaches to investigating color vision.