A theoretical study of surface lithium effects on the [111] SiC nanowires as anode materials.

CONTEXT: Silicon carbide nanowires (SiCNWs) are considered a promising alternative material for application in lithium-ion batteries, with researchers striving to develop new electrode materials that exhibit high capacity and high charge/discharge rate performance. To gain a deeper understanding of the application of SiCNWs in semiconductor material science and energy supply fields, we investigated the effects of nanoscale and surface lithiation on the electrical and mechanical properties of SiCNWs grown along the [111] direction. First-principles calculation was used to study their geometries, electronic structures, and associated electrochemical properties. Herein, we considered SiCNWs with full hydrogen passivation, full lithium passivation, and mixed passivation at different sizes. The formation energy indicates that the stability of SiCNWs increases with the increasing diameter, and the surface-lithiated SiC nanowires (Li-SiCNWs) are found to be energetically stable. The mixed passivated SiCNWs exhibit the properties of indirect band gap with the increase of lithium atoms on the surface, while the fully lithium passivated nanowires exhibit metallic behavior. Charge analysis shows that a portion of the electrons on the lithium atoms are transferred to the surface atoms of the nanowires and electrons prefer to cluster more near the C atoms. Additionally, Li-SiCNWs still have good mechanical resistance during the lithiation process. The stable open-circuit voltage range and theoretical capacity of these SiCNWs indicate their suitability as anode materials. METHOD: In this study, Materials Studio 8.0 was used to construct the models of the SiCNWs. And all the density functional theory (DFT) calculations were performed by the Vienna ab initio Simulation Package (VASP). The self-consistent field calculations are performed over a Monkhorst-Pack net of 1 × 1 × 6 k-points. The energy convergence criteria for the self-consistent field calculation were set to 10-5 eV/atom with a cutoff energy of 400 eV.

3D-Printed Mullite-Reinforced SiC-Based Aerogel Composites.

There is a growing demand for thermal management materials in electronic fields. Aerogels have attracted interest due to their extremely low density and extraordinary thermal insulation properties. However, the application of aerogels is limited by high production costs and the requirement that aerogel structures not be load-bearing. In this study, mullite-reinforced SiC-based aerogel composite (MR-SiC AC) is prepared through 3D printing combined with in situ growth of SiC nanowires in post processing. The fabricated MR-SiC AC not only has ultra-low thermal conductivity (0.021 W K m-1) and high porosity (90.0%), but also a high Young's modulus (24.4 MPa) and high compressive strength (1.65 MPa), both exceeding the measurements of existing resilient aerogels by an order of magnitude. These properties make MR-SiC AC an ideal solution for the precision thermal management of lightweight structures having complex geometry for functional devices.

Reduced graphene oxide/SiC nanowire composite aerogel prepared by a hydrothermal method with excellent thermal insulation performance and electromagnetic wave absorption performance.

In aerospace and downhole exploration, materials must function reliably in challenging environments characterized by high temperatures and complex electromagnetic (EM) interference. Graphene oxide (GO) aerogels are promising materials for thermal insulation, and the incorporation of silicon carbide nanowires can enhance their mechanical properties, thermal stability and EM absorption efficiency. In this context, citric acid acts as both a cross-linking and reducing agent, facilitating the formation of a composite aerogel comprising GO and SiC nanowires (rGO/m-SiC NWs). Compared with GO aerogels, the representative composite aerogel sample rGS4 demonstrated significantly improved mechanical properties (yield strength increased by 0.031 MPa), outstanding thermal stability (ability to withstand temperatures up to 800 °C) and remarkably low thermal conductivity (measuring just 0.061 W m-1K-1). Importantly, the composite aerogels displayed impressive EM absorption characteristics, including a slim profile (2.5 mm), high absorption capacity (-42.23 dB) and an exceptionally broad effective absorption bandwidth (7.47 GHz). Notably, the specific effective absorption bandwidth of composite aerogels exceeded that of similar composite materials. In conclusion, rGO/m-SiC NWs exhibited exceptional mechanical properties, remarkable thermal stability, efficient thermal insulation and outstanding microwave absorption capabilities. These findings highlight their potential for use in high-temperature and electromagnetically challenging environments.

Preparation and Electromagnetic Wave Absorption Properties of N-Doped SiC Nanowires.

Enhancing the conductivity loss of SiC nanowires through doping is beneficial for improving their electromagnetic wave absorption performance. In this work, N-doped SiC nanowires were synthesized using three different methods. The results indicate that a large amount of Si2ON will be generated during the microwave synthesis of SiC nanowires in a nitrogen atmosphere. In addition, the secondary heat-treatment of the as-synthesized SiC nanowires under nitrogen atmosphere will significantly reduce their stacking fault density. When ammonium chloride is introduced as a doped nitrogen source in the reaction raw material, the N-doped SiC nanowires with high-density stacking faults can be synthesized by microwave heating. Therefore, the polarization loss induced by faults and the conductivity loss caused by doping will synergistically enhance the dielectric and EMW absorption properties of SiC nanowires in the range of 2-18 GHz. When the filling ratio of N-doped SiC nanowires is 20 wt.%, the composite shows a minimum reflection loss of -22.2 dB@17.92 GHz, and an effective absorption (RL ≤ -10 dB) bandwidth of 4.24 GHz at the absorber layer thickness of 2.2 mm. Further, the N-doped SiC nanowires also exhibit enhanced high-temperature EMW absorption properties with increasing temperature.

ZnO-decorated SiC@C hybrids with strong electromagnetic absorption.

A novel strategy is provided to improve the absorption of SiC nanomaterials through surface carbonization of SiC nanowires and hydrolysis. SiC@C-ZnO composites were synthesized with different dosages of ZnNO3·6H2O. Composition, microstructure, and electromagnetic properties of the composites were characterized and analyzed. Results from TEM and XRD show that crystalline ZnO particles adhere to the surface of amorphous carbon, and the ZnO content increases as a function of a dosage of ZnNO3·6H2O. The as-prepared SiC@C-ZnO hybrids exhibit effective electromagnetic absorption, which is related to a synergy effect of different dielectric loss processes. The minimum reflection loss reached -65.4 dB at 11 GHz at a sample thickness of 3.1 mm, while the effective absorption bandwidth (EAB) reached 7 GHz at a sample thickness of 2.56 mm. Furthermore, the EAB of the samples can also cover the whole X band and Ku band at small sample thicknesses (2.09-3.47 mm). The excellent properties of the materials suggest great prospect as electromagnetic absorbers.

Hierarchical SiC-Graphene Composite Aerogel-Supported Ni-Mo-S Nanosheets for Efficient pH-Universal Electrocatalytic Hydrogen Evolution.

MoS2 exhibits good prospects in electrocatalytic hydrogen evolution. Whereas, the electrocatalytic property of MoS2 is restrained by its insufficient active sites, low electrical conductivity, and slow water dissociation processes. Herein, an aerogel composed of silicon carbide (SiC) and graphene (SiCnw-RGO) was constructed by growing SiC nanowires (SiCnw) in the graphene aerogel (RGO) via the CVD method, and then Ni-Mo-S nanosheets were hydrothermally synthesized on the SiCnw-RGO composite aerogel to develop an efficient pH-universal electrocatalyst. Ni-Mo-S nanosheets supported on SiCnw-RGO (Ni-Mo-S@SiCnw-RGO) exhibit an interesting hierarchical three-dimensional interconnected structure of composite aerogel. The optimal Ni-Mo-S@SiCnw-RGO electrocatalyst exhibits excellent catalytic performance with low Tafel slopes of 60 mV/dec under acidic conditions and 90 mV/dec under alkaline conditions. Density functional theory calculations demonstrate a composite catalyst exhibits advantageous hydrogen adsorption free energy and water dissociation energy barrier. This study provides a reference to design an efficient hierarchical aerogel electrocatalyst.

Bird-Nest-Like Multi-Interfacial MXene@SiCNWs@Co/C Hybrids with Enhanced Electromagnetic Wave Absorption.

Newly emerged two-dimensional transition metal carbides and/or nitrides (MXenes) have attracted considerable interest in the field of electromagnetic wave absorption, but their excessive conductivity and single loss mechanism limit their applicability. Herein, an MXene decorated with SiCNWs@Co/C was prepared by in situ growth and carbonization processes, followed by electrostatic self-assembly. The electromagnetic wave absorption performance of MXene@SiCNWs@Co/C with a bird-nest-like structure could be effectively regulated and optimized by changing the proportion of MXene and SiCNWs@Co/C. The prepared MXene@SiCNWs@Co/C hybrid absorbers reveal superior impedance matching, complementary dissipation mechanism, and plentiful heterointerfaces. Profiting from the synergy of abovementioned factors, the resultant MXene@SiCNWs@Co/C absorber exhibits an optimum reflection loss (RL) value of -76.5 dB at 6.36 GHz under a thickness of 3.9 mm and broad effective absorption bandwidth (EAB, RL ≤ -10 dB) of 6.2 GHz (11.8-18.0 GHz) with a thickness of only 2.0 mm, covering the entire Ku band. This work offers new insights into designing and fabricating highly efficient MXene-based electromagnetic absorbers.

Effect of Reinforcement Size on Mechanical Behavior of SiC-Nanowires-Reinforced 6061Al Composites.

In the present study, the effects of SiC nanowires (SiCnws) with diameters of 100 nm, 250 nm and 450 nm on the microstructure and mechanical behavior of 20 vol.% SiCnws/6061Al composites prepared by pressure infiltration were studied. It was found that the interface between SiCnws and Al matrix was well bonded, and no interface product was found. The thicker SiCnws are beneficial to improve the density. In addition, the bamboo-like and bone-like morphologies of SiCnws produce a strong interlocking effect between SiCnws and Al, which helps to improve the strength and plasticity of the material. The tensile strength of the composite prepared by SiCnws with a diameter of 450 nm reached 544 MPa. With a decrease in the diameter of SiCnws, the strengthening effect of SiCnws increases. The yield strength of SiCnws/6061Al composites prepared by 100 nm is 13.4% and 28.5% higher than that of 250 nm and 450 nm, respectively. This shows that, in nano-reinforced composites, the small-size reinforcement has an excellent improvement effect on the properties of the composites. This result has a guiding effect on the subsequent composite structure design.

Surface-potential-modulated piezoresistive effect of core-shell 3C-SiC nanowires.

The effect of surface potential on the carrier mobility and piezoresistance of core-shell silicon carbide nanowires (SiC NWs) was investigated to realize small and sensitive SiC-microelectromechanical systems sensors. The p-type cubic crystalline SiC (3C-SiC) NWs were synthesized via the vapor-liquid-solid method and coated with silicon dioxide (SiO2) or aluminum oxide (Al2O3) dielectric shells to form core-shell structured NWs with different surface potentials. Four-point bending devices (FBDs) with a field-effect transistor (FET) configuration integrating a single core-shell 3C-SiC NW as the FET channel were fabricated to apply an additional electric field and strain to the core-shell 3C-SiC NWs. The fixed oxide charge densities of the SiO2and Al2O3shells showed positive and negative values, respectively, which were equivalent to electric fields of the order of several hundred thousand volt per centimeter in absolute values. In the core-shell 3C-SiC NWs with originally low impurity concentrations, the electric field induced by the fixed oxide charge of the shells can determine not only the electrical conduction but also the charge carriers in the NWs. Bending tests using the FBDs showed that the piezoresistive effect of the SiO2-coated NW was almost the same as that of the as-grown 3C-SiC NW reported previously, regardless of the gate voltage, whereas that of the Al2O3-coated NW was considerably enhanced at negative gate voltages. The enhancement of the piezoresistive effect was attributed to the piezo-pinch effect, which was more pronounced in the NW, where the carrier density at the core-shell interface is enhanced by the electric field of the dielectric.

Thermal Radiation Shielding and Mechanical Strengthening of Mullite Fiber/SiC Nanowire Aerogels Using In Situ Synthesized SiC Nanowires.

Traditional solid nanoparticle aerogels have been unable to meet the requirements of practical application due to their inherent brittleness and poor infrared shielding performance. Herein, combining vacuum impregnation and high-temperature pyrolysis, a novel micro/nano-composite fibrous aerogel was prepared via in situ synthesis of silicon carbide nanowires (SiC NWS) in mullite fiber (MF) preform. During this process, uniformly distributed SiC NWS in the MF preform serve as an enhancement phase and also act as an infrared shielding agent to reduce radiation heat transfer, which can significantly improve the mechanical properties of the mullite fiber/silicon carbide nanowire composite aerogels (MF/SiC NWS). The fabricated MF/SiC NWS exhibited excellent thermal stability (1400 °C), high compressive strength (~0.47 MPa), and outstanding infrared shielding performance (infrared transmittance reduced by ~70%). These superior properties make them appealing for their potential in practical application as high-temperature thermal insulators.

Significant Improvement of Mechanical Properties of SiC-Nanowire-Reinforced SiCf/SiC Composites via Atomic Deposition of Ni Catalysts.

This study aimed to study the effects of different catalyst introduction methods on the distribution of SiC nanowires (SiCNWs) and the mechanical properties of SiCf/SiC composites. Two different catalyst-introduction methods (electroplating (EP) vs. atomic deposition (AD)) have been used to catalyze the growth of SiC nanowires in SiCf preforms. The morphology, structure and phase composition were systematically investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The SiCNWs-reinforced SiCf/SiC composited was densified by CVI. The compressive strength of the SiCNWs-reinforced SiCf/SiC composites was evaluated by radial crushing test. Compared with EP, atomic Ni catalysts fabricated by AD have higher diffusivity for better diffusion into the SiCf preform. The yield of SiCNWs is effectively increased in the internal pores of the SiCf preform, and a denser network forms. Therefore, the mechanical properties of SiCNW-containing SiCf/SiC composites are significantly improved. Compared with the EP-composites and SiCf/SiC composites, the compressive strength of AD-composites is increased by 51.1% and 56.0%, respectively. The results demonstrate that the use of AD method to grow SiCNWs is promising for enhancing the mechanical properties of SiCf/SiC composites.

The Formation Process and Strengthening Mechanism of SiC Nanowires in a Carbon-Coated Porous BN/Si3N4 Ceramic Joint.

Porous BN/Si3N4 ceramics carbon-coated by carbon coating were joined with SiCo38 (wt. %) filler. The formation process and strengthening mechanism of silicon carbide nanowires to the joint were analyzed in detail. The outcome manifests that there is no distinct phase change in the porous BN/Si3N4 ceramic without carbon-coated joint. The highest joint strength was obtained at 1320 °C (~38 MPa). However, a larger number of silicon carbide nanowires were generated in the carbon-coated joints. The highest joint strength of the carbon-coated joint was ~89 MPa at 1340 °C. Specifically, silicon carbide nanowires were formed by the reaction of the carbon coated on the porous BN/Si3N4 ceramic with the SiCo38 filler via the Vapor-Liquid-Solid (VLS) method and established a bridge in the joint. It grows on the ß-SiC (111) crystal plane and the interplanar spacing is 0.254 nm. It has a bamboo-like shape with a resemblance to alloy balls on the ends, and its surface is coated with SiO2. The improved carbon-coated porous BN/Si3N4 joint strength is possibly ascribed to the bridging of nanowires in the joint.

Layered Foam/Film Polymer Nanocomposites with Highly Efficient EMI Shielding Properties and Ultralow Reflection.

Lightweight, high-efficiency and low reflection electromagnetic interference (EMI) shielding polymer composites are greatly desired for addressing the challenge of ever-increasing electromagnetic pollution. Lightweight layered foam/film PVDF nanocomposites with efficient EMI shielding effectiveness and ultralow reflection power were fabricated by physical foaming. The unique layered foam/film structure was composed of PVDF/SiCnw/MXene (Ti3C2Tx) composite foam as absorption layer and highly conductive PVDF/MWCNT/GnPs composite film as a reflection layer. The foam layer with numerous heterogeneous interfaces developed between the SiC nanowires (SiCnw) and 2D MXene nanosheets imparted superior EM wave attenuation capability. Furthermore, the microcellular structure effectively tuned the impedance matching and prolonged the wave propagating path by internal scattering and multiple reflections. Meanwhile, the highly conductive PVDF/MWCNT/GnPs composite (~ 220 S m-1) exhibited superior reflectivity (R) of 0.95. The tailored structure in the layered foam/film PVDF nanocomposite exhibited an EMI SE of 32.6 dB and a low reflection bandwidth of 4 GHz (R < 0.1) over the Ku-band (12.4 - 18.0 GHz) at a thickness of 1.95 mm. A peak SER of 3.1 × 10-4 dB was obtained which corresponds to only 0.0022% reflection efficiency. In consequence, this study introduces a feasible approach to develop lightweight, high-efficiency EMI shielding materials with ultralow reflection for emerging applications.

Controllable Fabrication of SiC@C-Fe3O4 Hybrids and Their Excellent Electromagnetic Absorption Properties.

In this work, a batch of novel ternary hybrids (SiC@C-Fe3O4), characterized by SiC nanowires core, carbon shell, and adhered Fe3O4 nanoparticles were controllably synthesized via surface carbonization of SiCnw followed by hydrothermal reaction. Carbon, which was derived from SiC with nanometer thickness, possesses an amorphous structure, while Fe3O4 nanoparticles are in a crystalline state. Simultaneously, the inducement of Fe3O4 nanoparticles can provide significant magnetic loss, which is well-tuned by changing the molar content of iron precursors (FeCl3·6H2O and FeCl2·4H2O). SiC@C-Fe3O4 hybrids show great electromagnetic absorption performance owing to the synergy effect of dielectric and magnetic losses. The minimum refection loss can reach to -63.71 dB at 11.20 GHz with a thickness of 3.10 mm, while the broad effective absorption bandwidth (EAB) can reach to 7.48 GHz in range of 10.52-18.00 GHz with a thickness of 2.63 mm. Moreover, the EAB can also cover the whole X band and Ku band. The outstanding performance of the obtained material implys that it is a promising candidate as an electromagnetic absorber.

SiC Nanowire-Si3N4 Nanobelt Interlocking Interfacial Enhancement of Carbon Fiber Composites with Boosting Mechanical and Frictional Properties.

Carbon fiber composites composed of carbon fiber and pyrolytic carbon (PyC) matrix have great potential application in the brakes of aircrafts, where the combination of high mechanical strength and excellent frictional properties are required. In this work, two-component silicon-based interlocking enhancements were designed and constructed into carbon fiber composites for boosting the mechanical and frictional properties. Specially, silicon carbide nanowires (SiCnws) and silicon nitride nanobelts (Si3N4nbs) could form interlocking architectures, where SiCnws are rooted firmly on the carbon fiber surface in the radial direction and Si3N4nbs integrate the PyC matrix with carbon fibers together via a networked shape. SiCnws-Si3N4nbs not only refine the PyC matrix but also promote the bonding of the fiber/matrix interface and the cohesion strength of the PyC matrix, thus enhancing the mechanical and frictional properties. Benefiting from the SiCnws-Si3N4nbs synergistic effect and interlocking enhancement mechanism, the interlaminar shear strength and compressive strength of carbon fiber composites increased by 88.41% and 73.40%, respectively. In addition, the friction coefficient and wear rate of carbon fiber composites decreased by 39.50% and 69.88%, respectively. This work could open up an interlocking enhancement strategy for efficiently fabricating carbon fiber composites and promoting mechanical and frictional properties that could be used in the brakes of aircrafts.

Ultralight and High-Strength SiCnw@SiC Foam with Highly Efficient Microwave Absorption and Heat Insulation Properties.

An ultralight and high-strength SiCnw@SiC foam with highly efficient microwave absorption and heat insulation properties was successfully synthesized using the template sacrifice method and chemical vapor deposition process. The microstructure is a novel double network structure, which is formed by the coupling of the morphology-controlled SiCnw and the SiC skeleton. The introduction of SiCnw can not only provide more interface polarization and dielectric loss to the SiC foam, which greatly enhances the microwave absorption capacity of the composite foam, but also can enable it to act as an excellent radiation absorbent, which can effectively reduce the thermal conductivity of the foam, especially at high temperatures. In this study, a minimum reflection loss (RLmin) of -52.49 dB was achieved at 2.82 mm thickness with an effective absorption bandwidth of 5.6 GHz. As the length/diameter ratio of SiCnw decreases, the composite foam exhibits excellent high-temperature thermal insulation and mechanical properties. For the SiCnw@SiC foam, the thermal conductivity is only 0.304 W/mK at 1200 °C and the compressive strength reaches 1.53 MPa. This multifunctional SiCnw@SiC foam is an outstanding material, which has potential applications in microwave absorption and high-temperature heat insulation in harsh environments.

Hierarchical self-supporting sugar gourd-shape MOF-derived NiCo2O4 hollow nanocages@SiC nanowires for high-performance flexible hybrid supercapacitors.

Rational construction of hierarchical electrode materials has been a research hotspot in the field of energy storage. In this work, metal-organic framework (MOF) derived hollow NiCo2O4 nanocages (NCs) were strung by interwoven SiC nanowires (NWs) network on carbon cloth (CC), forming a unique sugar gourd-like core-shell architecture, which were fabricated via a multi-step process containing of chemical vapor deposition, solution reaction of MOF templates, ion exchanging/etching and subsequent heat treatment. Benefiting from the unique structural advantages, such as hierarchical porous structure with abundant active sites for electrochemical reactions and interwoven conductive networks for electron transport, the formed core-shelled CC/SiCNWs@NiCo2O4NCs as a binder supercapacitor electrode exhibits excellent electrochemical performance with a large specific capacitance (1377.6F g-1 at a current density of 1 A g-1), good rate capability (68.8% capacitance retention at 20 A g-1) and excellent cycling stability (88.3% capacitance retention after 6000 cycles). Furthermore, the hybrid supercapacitor based on CC/SiCNWs@NiCo2O4NCs and activated carbon, not only delivers a high energy density of 46.58 Wh kg-1 at the power density of 800 W kg-1, but also possesses good flexibility with high capacitance retention, exhibiting the application potential in the field of flexible energy storage. More importantly, our work gives a new thinking for structural design of SiCNWs-based and MOF-based electrode materials for high-performance flexible energy storage.

NiCo2O4 nanosheets sheathed SiC@CNTs core-shell nanowires for high-performance flexible hybrid supercapacitors.

Electrode materials with hierarchical self-supporting core-shell structures, with the metric of structural advantages and synergetic effect for different components, have been widely applied in supercapacitor. Besides, interface designing would improve the bonding of different components and further enhance the stability of electrochemical performance. In this work, by the introduction of CNTs layer to construct the conductive and rugged interface on SiC nanowires (NWs), the formed core-shell SiCNWs@CNTs network were served as conductive skeleton for supporting NiCo2O4 nanosheets (NSs). Benefiting from the unique hierarchical structure with designed interface, the formed SiCNWs@CNTs@NiCo2O4NSs electrode exhibits exceptional electrochemical performance with high specific capacitance of 2302F g-1 (319.7 mAh g-1) at 1 A g-1, excellent rate capability (86.3% capacitance retention at 20 A g-1) and outstanding cycling stability (95% capacitance retention after 5000 cycles). Furthermore, the hybrid supercapacitor assembled SiCNWs@CNTs@NiCo2O4NSs and activated carbon (AC), exhibits a high energy density of 64.2 Wh kg-1 at a power density of 0.79 kW kg-1, long cycle life and good flexibility. More impressively, this work provides a facile method for rationally constructing electrode materials with hierarchical structures for high-performance flexible energy storage devices.

Emerging One-/Two-Dimensional Heteronanostructure Integrating SiC Nanowires with MoS2 Nanosheets for Efficient Electrocatalytic Hydrogen Evolution.

MoS2 has emerged as a good application prospect in the electrocatalytic hydrogen evolution reaction (HER). Nevertheless, the catalytic activity of MoS2 is greatly restricted by its inferior electrical conductivity, inadequate exposure of active edge sites, and sluggish water dissociation dynamics. Herein, a 1D/2D heteronanostructure composed of SiC nanowires wrapped with MoS2 nanosheets was prepared via the hydrothermal synthesis of MoS2 on highly connected SiC nanowires (SiCnw). The nanocomposites exhibit an emerging tectorum-like morphology with interface connections of C-Mo bonds, which benefit the efficient interfacial transmission of electrons. Due to the synergetic catalytic effects of MoS2 nanosheets and SiC nanowires, the MoS2/SiCnw nanocomposites possess efficient catalytic performance with a low Tafel slope (55 mV/dec). SiC nanocrystals could reduce the activated water dissociation energy barrier, and the morphologies of connected nanowires could improve the active site exposure and charge transport. The nanocomposites possess favorable hydrogen adsorption free energy from density functional theory (DFT) calculations. The electrocatalytic performance of MoS2/SiCnw nanocomposites could be further improved by assembling the nanocomposites on a carbon fiber paper to enhance the electronic transmission efficiency.

Effect of Extrusion Temperature on the Microstructure and Mechanical Properties of SiCnw/2024Al Composite.

In the present research work, the effect of extrusion temperature from 480 to 560 °C on the microstructure and mechanical behavior of the SiCnw/2024Al composite (15 vol.%) has been explored. It has been found that extrusion at higher temperature (above 520 °C) was beneficial for the densification of the composite, while the residual average length and alignment of the SiC nanowires were also increased with the extrusion temperature. Moreover, higher extrusion temperature was helpful for the mechanical strength of the SiCnw/2024Al composite, and the peak-aged SiCnw/2024Al composite extruded at 560 °C revealed the highest strength (709.4 MPa) and elastic modulus (109.8 GPa).