Gemini cationic surfactant of 1, 3-bis (dodecyl dimethyl ammonium chloride) propane as a novel excellent inhibitor for the corrosion of cold rolled steel in HCl solution.

Gemini surfactants have become the research focus of novel excellent inhibitors because of their special structure (two amphiphilic moieties covalently connected at head group by a spacer) and excellent surface properties. It is proved by theoretical calculations that 1, 3-bis (dodecyl dimethyl ammonium chloride) propane (BDDACP) molecules can perform electron transfer with Fe (110). And it has a small fraction free volume, thus greatly reducing the diffusion and migration degree of corrosive particles. The potentiodynamic polarization curve showed that coefficients of cathodic and anodic reaction less than 1 and polarization resistance increased to 1602.9 Ω cm-2 after added BDDACP, confirming that BDDACP significantly inhibited the corrosion reaction by occupying the active site. The electrochemical impedance spectrum of imperfect semi-circle shows that the system resistance increases and double layer capacitance after added BDDACP. Weight loss tests also confirmed that BDDACP forms protective film by occupying the active sites on steel surface, and the maximum inhibition efficiency is 92 %. Comparison of the microscopic morphology showed that steel surface roughness was significantly reduced after added BDDACP. The results of time-of-flight secondary ion mass spectrometry show that steel surface contains some elements from BDDACP, which confirms the adsorption of BDDACP on steel surface.

Carbon emissions in China's steel industry from a life cycle perspective: Carbon footprint insights.

China is the most important steel producer in the world, and its steel industry is one of the most carbon-intensive industries in China. Consequently, research on carbon emissions from the steel industry is crucial for China to achieve carbon neutrality and meet its sustainable global development goals. We constructed a carbon dioxide (CO2) emission model for China's iron and steel industry from a life cycle perspective, conducted an empirical analysis based on data from 2019, and calculated the CO2 emissions of the industry throughout its life cycle. Key emission reduction factors were identified using sensitivity analysis. The results demonstrated that the CO2 emission intensity of the steel industry was 2.33 ton CO2/ton, and the production and manufacturing stages were the main sources of CO2 emissions, accounting for 89.84% of the total steel life-cycle emissions. Notably, fossil fuel combustion had the highest sensitivity to steel CO2 emissions, with a sensitivity coefficient of 0.68, reducing the amount of fossil fuel combustion by 20% and carbon emissions by 13.60%. The sensitivities of power structure optimization and scrap consumption were similar, while that of the transportation structure adjustment was the lowest, with a sensitivity coefficient of less than 0.1. Given the current strategic goals of peak carbon and carbon neutrality, it is in the best interest of the Chinese government to actively promote energy-saving and low-carbon technologies, increase the ratio of scrap steel to steelmaking, and build a new power system.

Ultrasonic Evaluation of Laser Scanning Speed Effect on the Spectral Properties of Three-Dimensional-Printed Metal Phononic Crystal Artifacts.

Additive manufacturing/three-dimensional printing (AM/3DP) processes promise a flexible production modality to fabricate a complex build directly from its digital design file with minimal postprocessing. However, some critical shortcomings of AM/3DP processes related to the build quality and process repeatability are frequently experienced and reported in the literature. In this study, an in situ real-time nondestructive monitoring framework based on the dispersive properties of phononic crystal artifacts (PCAs) to address such quality challenges is described. Similar to a witness coupon, a PCA is printed alongside a build while it is interrogated and monitored with ultrasound. A PCA is substantially smaller than the actual build. Due to its periodic internal structures, a PCA creates pass and stop bands in its spectral response, which are sensitive to the variations in its process and material parameters. These periodic structures, representing the geometric complexities of an actual build, are designed for a specific monitoring objective(s) in AM/3DP. As a model application, in this demonstration study, the effect of the laser scanning speed of a slective laser melting (SLM) printer on the spectral properties of metal PCAs (mPCAs) is ultrasonically evaluated offline. The dependency of the pressure and shear wave speeds, the apparent Young's and shear moduli, and Poisson's ratio on the scanning speed are quantified, and it is found that they are highly sensitive to the laser scanning speed of an SLM printer. The sensitivity of the peaks of the pressure and shear spectral waveforms acquired for the identical mPCA designs printed on the same build plate with the same process parameters is also quantified. For powder-based AM/3DP technologies, where scanning speed is among the crucial process parameters such as laser power and bed temperature, the reported correlations between scanning speeds and the mechanical and spectral features of the mPCAs are expected to be instrumental in developing in situ real-time monitoring systems.

A Comparable Study on Laser Welding Behaviors of Selective Laser Melted 304 Stainless Steel, Inconel 718 Superalloy and Ti-6Al-4V Alloy.

The hybrid selective laser melting (SLM) technology by laser welding can capture the superiorities of both processes to produce large-scale, high-quality, high-resolution, and complicated-shaped metallic parts. In this work, the SLMed 304 stainless steel, Inconel 718 superalloy, and Ti-6Al-4V alloy sheets were joined by laser welding under various building directions. And then, the microstructure, microhardness, tensile properties, and corrosion resistance of the laser-welded SLMed 304 stainless steel, Inconel 718 superalloy, and Ti-6Al-4V alloy were compared to explore the effect of SLMed microstructural anisotropy and crystal structure. The results showed that phase constitutions were the same between the SLMed and laser-welded joints for the three alloys. But the grain size and dendrite arm spacings in the joints were coarser than those in the SLMed samples. The SLMed microstructural anisotropy resulted in differences in the thermal gradient, grain size, dendrite arm spacing, and tensile properties in the joints under various welding types. Compared with the SLMed counterparts, the laser-welded 304 stainless steel and Inconel 718 joints showed lower microhardness and tensile properties but better corrosion resistance. In contrast, the laser-welded Ti-6Al-4V joints possess a higher microhardness, tensile properties, and corrosion resistance. Therefore, it is feasible to join SLMed parts to manufacture large-scale parts by laser welding.

On the Development of Smart Framework for Printability Maps in Additive Manufacturing of AISI 316L Stainless Steel.

In this work, we propose a methodology to develop printability maps for the laser powder bed fusion of AISI 316L stainless steel. Regions in the process space associated with different defect types, including lack of fusion, balling, and keyhole formation, have been considered as a melt pool geometry function, determined using a finite element method model containing temperature-dependent thermophysical properties. Experiments were performed to validate the printability maps, showing a reliable correlation between experiments and simulations. The validated simulation model was then applied to collect the data by varying laser scanning speed, laser power, powder layer thickness, and powder bed preheating temperature. Following this, the collected data were used to train and test the adaptive neuro-fuzzy interference system (ANFIS)-based machine learning model. The validated ANFIS model was used to develop printability maps by correlating the melt pool characteristics to the defect types. The smart printability maps produced by the proposed methodology can be used to identify the processing window to attain defects-free components, thus attaining dense parts.

The corrosion inhibition performance of a diissocyanate-imidazole based organic compound during acid cleaning of MSF desalination plant.

Inorganic scale formation is a common issue in multi-stage flash (MSF) desalination plants, significantly impacting operational efficiency. To address this, acid cleaning is frequently employed, but it can lead to severe corrosion of alloy components if not properly controlled with corrosion inhibitors. This study investigates the effectiveness of toluene-2,4-diisocyanate-4-(1H-imidazole-ly) aniline (TDIA) as a corrosion inhibitor for 304L stainless steel in a simulated acid cleaning solution (1M HCl and 3.5 % NaCl). A range of tests, including electrochemical analysis, weight loss measurements, and surface characterization techniques such as AFM, EDS, and SEM, were used to assess the inhibitor's performance at temperatures of 25, 45, 65, and 90 °C. At a concentration of 50 ppm, TDIA achieved inhibition efficiencies of around 90% at 25 °C and above 80% at 90 °C, demonstrating effective protection across all temperatures studied. The adsorption behavior of TDIA followed the Langmuir adsorption model, and it acted as a mixed-type inhibitor by forming a protective layer on the metal surface, which prevents corrosive agents from accessing the steel. The dual-environment testing method, simulating conditions in desalination plants, offers valuable insights into the inhibitor's practical performance, enhancing the applicability of these findings to real-world industrial scenarios.

Facile fabrication of ZnO nanoparticles via non-thermal plasma technique and their anti-corrosive effects on X60 API 5L steel in 1M HCl solution.

This work aims to explore the efficiency of ZnO nanoparticles synthesized via the non-thermal gliding arc discharge-assisted plasma (NT-GAD) technique for inhibiting the corrosion of X60 API 5L steel in a 1M HCl environment. The XRD pattern revealed that the ZnO nanoparticles exhibit hexagonal wurtzite structure with average particle size of ∼24 nm. UV-visible spectroscopy analysis revealed an absorption peak centering at 365 nm, corresponding to an energy band gap of 3.29 eV. SEM and TEM analysis revealed that the nanoparticles exhibit an agglomerated and irregular morphology. The corrosion inhibition of ZnO NPs was investigated via the electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization tests (PDP), while varying both concentration and temperature. The results revealed that the increase in inhibitor concentration resulted in a higher activity at ambient temperature, with an optimal efficiency of 93 % at a concentration of 100 mg/L. However, the increase in temperature remarkably reduced the inhibition efficiency, suggesting a physisorption behavior of ZnO NPs onto the steel surface. AFM and FE-SEM analysis confirmed the formation of a protective layer on the X60 API 5L steel surface. This study emphasizes the significant potential of ZnO NPs synthesized via the NT-GAD assisted plasma technique as corrosion inhibitor for X60 API 5L carbon steel in 1M HCl corrosive media.

Mitigation of biocorrosion of X80 carbon steel by a shale microbiome biofilm using a green biocide enhanced by d-amino acids.

Microbiologically influenced corrosion (MIC) in shale gas field is a major threat with the hydraulic fracturing fluid injected into the subsurface. In this study, the microbiome collected from a shale gas produced water sample was extracted and cultivated in ATCC 1249 medium modified with 10 g/L NaCl anaerobically at 30 °C. d-amino acids, which were reported as biocide enhancers, were found to enhance 2,2-dibromo-3-nitrilopropionamide (DBNPA) biocide on the mitigation of shale microbiome MIC on X80 carbon steel. The combination of 50 ppm (w/w) d-leucine + 50 ppm d-alanine + 1 ppm d-tyrosine had the best enhancement effect on 50 ppm DBNPA with 84 % less weight loss, and 67 % lower corrosion current density (icorr) compared to 50 ppm DBNPA alone. The corrosion data were consistent with the enhanced biofilm inhibition observation. The experimental data also indicated that d-tyrosine used alone at a low dosage of 1 ppm enhanced DBNPA considerably, with 44 % less weight loss and 47 % less icorr. The electrochemical results showed the positive response of shale gas microbiome biofilm to the injected magnetite nanoparticles indicating the extracellular electron transfer might be a main mechanism for its corrosion.

Recycling steel slag as fertiliser proxy in agriculture is good circular economy but disrupts plant microbial symbioses in the soil.

Modern agriculture depends on synthetic fertilisers to ensure food security but their manufacture and use accounts for ~5 % of the global greenhouse gas emissions. Achieving climate change targets therefore requires alternatives, that while maintaining crop productivity, reduce emissions across the lifecycle of fertiliser utilisation. Steel slag, a nutrient-rich by-product of steel manufacture, offers a viable alternative. Being substantially cheaper than fertilisers, it is economically attractive for farmers, particularly in low-middle income countries of the Global South. However, slag application in agriculture poses risk of pollutant transfer to the human food chain and disruption of key plant-microbe symbioses like the arbuscular mycorrhizal fungi (AMF). Here, using barley as a model crop, we tested the suitability of slag as a fertiliser proxy. Mycorrhizal and non-mycorrhizal barley were grown in soils ameliorated with slag in concentrations of 0, 2, 5 and 10 t ha-1. We analysed slag-mycorrhiza interaction and their combined effects on crop yield and risks to human nourishment. Slag increased grain yield by respective 32 and 21 % in mycorrhizal and non-mycorrhizal barley. Grain concentration of metal pollutants in mycorrhizal and non-mycorrhizal barley fertilised with slag were within the WHO recommended limits. But slag reduced mycorrhizal colonisation in barley roots and extraradical hyphal spread in the soil. The consequent decline in symbiont function lowered AMF-mediated plant nutrient uptake and increased mineral losses in leachates. AMF are keystone species of the soil microbiome. Loss of AMF function presents long-term ecological consequences for agriculture and necessitates a careful evaluation of slag application to soil.

Evaluation of Nickel and Titanium Releasing from Titanium-coated Stainless Steel Crowns Regarding Trimming: An In Vitro Study.

Introduction: Stainless steel crowns (SSCs) are the most durable and effective restorations for primary teeth. Titanium-coated SSCs are newer on the market, and this study was conducted to assess the amount of nickel (Ni) and titanium ions released from titanium-coated SSCs, with and without trim, in artificial saliva. Materials and methods: A total of 60 titanium-coated SSCs were divided into two groups-group I (n = 30, without trim) and group II (n = 30, with trim) and were immersed in 5 mL artificial saliva. The amount of Ni and titanium released in each group was measured by inductively coupled plasma-mass spectrometry on days 1, 7, and 21. Results: The amount of Ni ion released in group I on day 1 was 0.0096 ppm and reduced on day 7 (0.0091 ppm) and day 21 (0.0088 ppm). Whereas the amount of Ni ion released in group II was the same for all 3 days (0.0096 ppm). The amount of titanium ion released in both groups was the same on all 3 days (0.00108 ppm). Conclusion: There was no significant difference seen in the mean Ni and titanium ion release between the two groups on all 3 days. The cumulative release of metals from titanium-coated SSCs in each of the groups was significantly lower than the level required to produce any harmful effects. Any of the groups of commercially available SSCs can be used in pediatric dentistry. How to cite this article: Biradar R, Siaddaiah SB, Bhat PK. Evaluation of Nickel and Titanium Releasing from Titanium-coated Stainless Steel Crowns Regarding Trimming: An In Vitro Study. Int J Clin Pediatr Dent 2024;17(5):524-527.

Electrochemical, gravimetric and surface studies of Phalaris canariensis oil extract as corrosion inhibitor for 316 L type stainless steel in H2O-LiCl mixtures.

The corrosion inhibition action of Phalaris canariensis extract on 316 L stainless steel in the H2O-35 (wt%) LiCl mixture at different temperatures has been evaluated with the aid of weight loss, potentiodynamic polarization curves, linear polarization resistance and electrochemical impedance spectroscopy tests. These studies were complemented by Fourier Transformed Infrared spectroscopy, FTIR, gas/mass chromatography analytical techniques and detailed scanning electronic microscopy studies. Results have indicated that Phalaris canariensis extract is an efficient inhibitor, with an efficiency that increases with its concentration, but it decreases as the temperature increases. Phalaris canariensis extract is physically adsorbed onto stainless steel according to a Temkin type of adsorption isotherm. Phalaris canariensis extract affected both anodic and cathodic electrochemical reactions with a stronger effect on the anodic ones, acting, thus, as a mixed type of inhibitor. Main compounds contained in the Phalaris canariensis extract were palmitic and oleic acids, responsible for its inhibitory properties.

Influence of the elevation effect of slope blasting on the vibration velocity of existing buried steel pipes.

Blasting vibration(BV) may cause the instability and damage to the surrounding structures and infrastructures, even leading to serious accident. As far as slope blasting is concerned, more and more attention has been paid to the elevation effect of BV of rock mass. However, scarce information is available on the influence of the elevation effect of slope blasting on the BV of surrounding structures, especially the existing buried pipes. As a consequence, the influence of the elevation effect of slope blasting on the BV of steel pipes was numerically investigated according to finite element model, which was verified against the experimental result. Moreover, the formula is presented to predict the peak vibration velocity (PVV) of steel pipes under slope blasting. It is found that PVV of the steel pipes has the elevation amplification effect in the terrain with positive or negative elevation difference. PVV of the pipes in the terrain with positive elevation difference is greater than that in the terrain with the same negative elevation difference. The elevation effect is more obvious under the condition of the positive elevation difference (2.1-5.1 m). The modified Sadovsky's empirical formula is more suitable to predict PVV of the buried steel pipes during the slope blasting process.

Round robin experiment to detect, size, and characterize flaws in the welds of existing hydraulic steel structures using phased array ultrasonic testing.

Limited information exists on the ability of nondestructive testing techniques to detect, size, and characterize flaws in existing hydraulic steel structures (HSS). Round robin experiments were conducted using phased array ultrasonics to inspect welded steel specimens representing joints in existing HSS. Technicians detected 83% of the flaws scanned, but detection rates varied widely by flaw and technician. Uncertainty in flaw size estimates, represented by 90% confidence bounds on the ratio of estimated to actual length or height, ranged from 0.52 to 2.10 for length and 0.32 to 3.59 for height. Planar, volumetric and laminar flaws were accurately characterized 80% of the time.

Electrochemical, surface, and theoretical investigations of palm kernel shell extract as an effective inhibitor for carbon-steel corrosion in 1 M HCl solution.

Herein, we employed palm kernel shell extract (PKSE) as an eco-friendly inhibitor for carbon steel in acidic-induced corrosion. The corrosion inhibition of PKSE on carbon steel in 1 M HCI solution was investigated by electrochemical impedance spectroscopy, weight loss, and potentiodynamic polarization measurements. The surface was characterized by scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy. Moreover, the elastic modulus and hardness tests were conducted. Weight loss measurements revealed that the optimum concentration of inhibitors is 500 ppm with 95.3% inhibition efficiency in 1 M HCl solution. Electrochemical results showed that the inhibitor could exhibit excellent corrosion inhibition performance and displayed mixed-type inhibition. The electrochemical impedance spectroscopy analysis shows that the inhibition performance increases by increasing the concentration of PKSE. The surface studies ensure the PKSE effectiveness in carbon steel surface damage reduction. Also, the adsorption of PKSE molecules on the carbon steel surface occurs according to the Langmuir isotherm model. The primary goal of this investigation was the utilization of palm kernel shell extract as corrosion inhibitor for 1018 low carbon steel in 1 M HCl solution, which highlights its novelty. The present results will be helpful to uncover the versatile importance of palm kernel shell compounds in the corrosion inhibition process.

Stability analysis of deep foundation pit with a double-row cast-in-place piles and diagonal steel lattice braces under sloped excavation conditions.

Existing deep foundation pit support structures are commonly composed of external earth-retaining structures, internal horizontal bracings, and vertical columns. A closed bracing system, often formed by a horizontal support through a bracket board, frequently impedes vertical excavation and soil removal operations in the foundation pit, and the processes of assembly and dismantling are complex and time-consuming. This study presents a combined support system and construction method consisting of cast-in-place piles and diagonal steel lattice braces. For sloped excavation, diagonal braces were constructed by slotting through the reserved soil, allowing the use of a single layer of support within the excavation depth. This approach significantly optimizes the construction process, reducing both project duration and overall cost. The field monitoring results indicated that the support method effectively controlled the lateral displacement of the pile bodies. Field monitoring results demonstrated that the proposed support system effectively controlled the lateral displacement of the pile bodies. The adoption of a support-first, excavation-second approach significantly controlled the settlement of the ground surface around the foundation pit, thereby preventing excessive increments in the axial force of the supports due to the large longitudinal depth excavation. The calculation results of the three-dimensional finite element model for foundation pit excavation and support indicate that the proposed support method results in a decreasing ratio of the maximum lateral deformation depth of the pile body, denoted as δh-m, to the excavation depth He as the excavation depth increases. This implied that the displacement of the pile body was strictly controlled. When the depth of the foundation pit excavation exceeded 10 m, the maximum lateral deformation occurred below 10 m along the pile shaft. The diagonal steel lattice braces transferred the load to the top of the cast-in-place piles at the bottom of the pit, where the stress concentration occurred. During construction, special attention must be paid to the strength of the connection between the pile top and the connecting beams.

Simulation study of turning-ultrasonic rolling compound processing for 42CrMo steel.

The ultrasonic rolling processing technology has been shown to significantly reduce surface roughness and enhance the residual stress of parts, thereby improving their surface properties and extending their service life. This technology is particularly effective for the precision machining and surface strengthening of ultra-high-strength steel 42CrMo. This study aims to investigate the impact of turning pre-processing on the distribution of residual stress during ultrasonic rolling, a simulation model incorporating turning pre-processing was developed and used to conduct ultrasonic rolling simulation experiments, enabling the analysis of residual stress distribution patterns. Concurrently, ultrasonic rolling strengthening experiments were performed to validate the accuracy of the simulation model. The results confirm that with increasing rotational speed and feed rate, residual stress decreases, whereas with increasing static pressure and amplitude, residual stress increases. The residual stress variation obtained from the simulation of combined turning and ultrasonic rolling closely matched the results of experimental ultrasonic rolling tests. This consistency validates the accuracy of the simulation model. This study offers a novel approach for simulating and experimentally validating ultrasonic rolling processes, particularly for shaft-like parts that undergo turning as a pre-processing step.

Experimental and theoretical simulations to examine the influence of nonionic surfactant on the corrosion control of mild steel in hydrochloric acid.

The increasing demand for corrosion prevention strategies that are both effective and sustainable is part of the research the background. Nonionic surfactants offer a potential replacement for traditional corrosion inhibitors. These surfactants are well-known for their low toxicity and biodegradability. The research involved conducting experimental tests (such as weight loss, polarization and impedance spectroscopy) and theoretical computations to investigate the role of nonionic surfactant (polyoxyethylene (7) tribenzyl phenyl ether) (PETPE) in controlling the corrosion of mild steel in hydrochloric acid (1.0 M HCl) environment. The results of the study demonstrated that PETPE exhibited significant corrosion inhibition properties for mild steel in HCl solution. The inhibition efficiency of PETPE was found to increase with increasing PETPE concentration. PETPE is an excellent corrosion inhibitor because it significantly reduces the rate of corrosion, as seen by the notable inhibition efficiency result (95.4%) at a relatively low dose of PETPE (100 ppm). Thermodynamic studies were used to discuss the fundamental mechanisms that control PETPE-acid interactions. The adsorption process followed Langmuir adsorption isotherm, indicating a monolayer adsorption of the PETPE on the mild surface. Theoretical computations confirm the strong inhibition behavior of PETPE. The innovative feature of this research is its comprehensive strategy, which integrates experimental studies and theoretical simulations to evaluate the impact of PETPE on the corrosion control of mild steel in hydrochloric acid. The combined effort has the ability to supply valuable knowledge into the mechanisms of corrosion that will lead to the establishment of powerful corrosion control strategies.

Of the article: evaluation of the masticatory efficiency of children with stainless steel crowns: a pilot cross-sectional split-mouth study.

BACKGROUND: Stainless steel crowns (SSCs) are commonly employed to restore the posterior teeth of children and over the years, they are available with improved anatomical shapes. This study was conducted to evaluate and assess the effect of the placement of SSCs on the masticatory efficiency of children. METHODS: This pilot cross-sectional split-mouth study assessed masticatory efficiency in children aged 6-11 years. Fifteen participants, each with stainless-steel crowns placed unilaterally at least one month prior, were included. This study utilized two flavours of trident chewing gum (red and green) to measure masticatory efficiency. The child was asked to chew half a strip of red and green chewing gum placed one on top of the other using either the noncrown or crown side 15 times. Another set of chewing gum was given to the child to chew 20 times on the same side. The chewing exercise was repeated using teeth on the other side. Chewed gum samples were collected, photographed, and analysed via ImageJ software to determine the red and green areas. Masticatory efficiency was subsequently calculated with the help of a formula in which the red areas and green areas were calculated via ImageJ software. The data were analysed with paired t tests via SPSS (version 20.0). RESULTS: When the mean values of the crown side were compared with those of the noncrown side following 15 chewing cycles, the chewing efficiency on the noncrown side was greater, with a difference of 0.303, whereas the chewing efficiency following 20 chewing cycles was greater on the crown side, with a difference of 0.814. However, both differences were statistically nonsignificant, with t values of -0.07 and 0.26, respectively, and p values of 0.94 and 0.8, respectively. CONCLUSION: The presence of SSCs on the molars of children did not affect masticatory efficiency.

Concurrent removal of Fe(II), Cu(II), and Zn(II) cations from acid mine drainage by an industrial solid waste - steel slag: Behaviors and mechanisms.

Acid mine drainage (AMD) contamination poses a severe environmental threat and is a significant risk to human health. There is an urgent need to develop environmentally sustainable and technically viable solutions for water contamination caused by heavy metals. In this study, steel slag (SS) was used as a secondary resource to concurrently remove Fe(II), Cu(II), and Zn(II) from AMD. Because of the loose and porous structure, abundant functional groups, fast sedimentation velocity, and excellent solid-liquid separation, SS showed exceptional removal performance for heavy metal ions. The adsorption kinetic data of Fe(II), Cu(II), and Zn(II) showed good regression with the pseudo-second-order model. Besides, the adsorption of Fe(II) by SS conformed to the Freundlich model, whereas the adsorption of Cu(II) and Zn(II) followed the Langmuir model, with the maximum adsorption amounts of Cu(II) and Zn(II) being 170.69 and 155.98 mg/g. Furthermore, competitive adsorption was observed among Fe (II), Cu (II), and Zn (II) in a multi-component system, with the adsorption priority being Fe (II) > Cu (II) > Zn (II). The removal mechanism of Fe(II), Cu(II), and Zn(II) in AMD by SS mainly includes electrostatic attraction, chemical precipitation, and surface complexation. Interestingly, the leached concentrations of Fe(II), Cu(II), and Zn(II) from the spent slag after calcination were all within the detection limit of the Chinese emission standard, demonstrating excellent environmental stability. Theoretically, this renders it a viable candidate for use as an additive in construction materials. Meaningfully, the work offers a practical approach for energy-efficient and eco-friendly heavy metal ions adsorption, and the secondary utilization of SS also contributes to the sustainable development of the steel industry. It is beneficial to implement the development concepts of clean production and efficient utilization of industrial solid waste.

Characterization of Carbide Precipitation in Low-Carbon Martensitic Steels Using an Ultrawide Field-of-View 3D Atom Probe.

It is important to understand the carbide distribution around high-energy sites such as dislocations and grain boundaries in martensitic steels as they have a major influence on the alloy performance. The aim of this study is to characterize fine ε carbides precipitated in low-carbon lath martensitic steel using the ultrawide field-of-view (FoV) CAMECA Invizo 6000 atom probe. We demonstrate the advantages of the wide FoV and determine the optimum conditions for analysis, by comparing the results such as the background noise and the C++/C+ charge state ratio (CSR) between voltage-pulsed and laser-pulsed modes. Increasing the laser pulse energy decreased the background noise and the CSR, where 70 pJ laser pulse energy produced a comparable mass-to-charge ratio spectrum to that recorded in voltage-pulsed mode, with the bulk compositions of C, Si, and Mn closest to that measured using voltage-pulsed mode. Increasing laser pulse energies to above 300 pJ decreased the bulk carbon content, with a more diffuse distribution of carbon around the carbides. This paper outlines some of the important experimental considerations when performing quantitative study of carbide precipitation in low-carbon martensitic steels using the Invizo 6000, considerations that can also be applied to other ferrous and non-ferrous alloy systems.