RESUMO
In this paper, the mechanical properties of micropowder cement mortar and engineered cementitious composites (ECC), using different processing municipal solid waste incineration (MSWI) as a mineral admixture, were investigated. Through the direct ball milling method, ball milling heat treatment method, water washing ball milling method and water washing heat treatment ball milling method, the mechanical properties of MSWI bottom slag-regenerated micropowder cement mortar were tested. Compared with other groups, the flexural strength and compressive strength of the specimen prepared by the MSWI after washing and heating (750 °C, 5 h) were the highest, which reached 82.0% and 81.0% of the reference group, respectively. Based on this treatment, a uniaxial tensile test, three-point bending test and single fiber pull-out test were then carried out to explore the relevant ECC properties containing MSWI. The strain-hardening index PSH of ECC was determined by analyzing the fracture toughness and elastic modulus, fiber/matrix interface chemical bond and friction bond strength of ECC containing MSWI. The results showed that the PSH index of ECC was higher when the treated powder content was 2.2, the w/c ratio was 0.25 and the fiber volume content was 2.0%. This led to higher tensile ductility, which made it easier to achieve stable multi-slit cracking and strain-hardening behavior.
RESUMO
In order to achieve an effective balance between plasticity and strength, a group of Ti-26Nb-xZr-yMn (x = 4, 7, 10 wt% and y = 3, 5 wt%) alloys were designed to evaluate the effects of Mn and Zr on the microstructures, mechanical properties and strengthening effects of the TiNb system. All the investigated alloys illustrate a monolithic ß phase in their microstructure and they all possess substantial true plasticity (~160%) and true maximum strength (~ 950 MPa) without fracture during the compression tests within the load capacity of 100 kN. The contribution of solid-solution, grain-boundary and dislocation strengthening mechanisms have been evaluated using the strengthening model for ß Ti alloys for all the investigated alloys. Among the investigated alloys, Ti-26Nb-4Zr-5Mn demonstrates the highest true yield strength (654 MPa), dislocation density (2.45 × 1015 m-2) and hardness (242 HV) along with improved strain hardening ability in terms of strain hardening indices (0.42 and 0.09). Furthermore, based on the superior mechanical properties among the investigated alloys, the electrochemical performance of Ti-26Nb-4Zr-3Mn and Ti-26Nb-4Zr-5Mn have also been analyzed in this work. The electrochemical measurements show that both alloys have almost similar corrosion potential and corrosion current density in simulated body fluid, i.e., -0.45 V and 0.838 nA/cm2 for Ti-26Nb-4Zr-3Mn, -0.48 V and 0.839 nA/cm2 for Ti-26Nb-4Zr-5Mn, respectively.
Assuntos
Ligas/química , Manganês/química , Nióbio/química , Titânio/química , Zircônio/química , CorrosãoRESUMO
This research aims to characterize damage at the sheared edge caused by the blanking operation of magnesium alloy AZ31B sheets. Shearing tests were carried out on an in-house blanking die-set and mechanical press (universal testing machine) by varying punchâ»die clearance and temperature. Edge damage was distinguished by the geometrical features of the sheared edge and by the distribution of the edge strain hardening (ESH) index. In this account, optical microscopy and scanning electron microscopy were applied to examine the characteristic dimensions of the sheared edge, fracture profile, and sheared edge quality, while the Vickers hardness test was applied to observe the surface micro-hardness in the shear zone (SZ) and the shear affected zone (SAZ). It was concluded that the blanking of magnesium alloy sheets at room temperature results in sheared edge defects, due to premature fracture, referred to here as micro-cracks, loose particles, and a jagged-plus-curved fracture profile. However, such deformities were completely suppressed with the rise in temperature. In addition, based on optical morphology, micro-hardness tests, and microstructure evolution, the recommendation regarding blanking temperature for the magnesium alloy AZ31B has was proposed.