Effects of testing speed on the tensile and mode I fracture behavior of specimens printed through the Fused Deposition Modeling technique.

Additive Manufacturing (AM) processes are known as revolutionary manufacturing processes that fabricate a part using a 3D model layer upon layer. These techniques gained more attention from various industries due to their advantages like low waste material. Also, these processes can produce any part with high degrees of complexity in a short period of time. The Fused Deposition Modeling (FDM) process is a material extrusion-based technique which works by extruding a fine molten polymeric filament through a heated nozzle on the heated platform named printer bed. In this method, some important manufacturing parameters play a crucial role in controlling the mechanical properties and quality of the final fabricated part. However, all printed specimens through the FDM process should be tested based on the standards under some critical circumstances. Thus, in the current research paper, five and three test speeds are considered in tensile and fracture testing procedures, respectively to evaluate how these speeds can affect the mechanical and mode I fracture properties. Also, as the FDM specimens present elastic-plastic behavior, the critical value of J-integral is assumed as a fracture assessment and calculated from the finite element analysis. Among the mechanical properties, ultimate tensile strength is affected significantly by the test speed. For instance, the ultimate tensile strength of FDM specimens is 39.02, 38.58, 42.33, 48.09, and 52.11 for test speeds of 2, 4, 6, 8, and 10 mm/min, respectively. But vice-versa results are detected for the mode I fracture behavior and corresponding values of J for the FDM-PLA specimens. Finally, experimental and numerical results together with comprehensive discussions about the considered speeds and obtained results are reported.

On the influence of test speed and environment in the fatigue life of small diameter nitinol and stainless steel wire.

To better understand the complex interplay of speed and environment on metals commonly used in implants, rotary bend fatigue tests were conducted on stainless steel and nitinol wires. A range of alternating strains was tested to create ε-N curves at two speeds (physiologic and accelerated) and in three environments (deionized water at body temperature, phosphate buffered saline at body temperature, and laboratory air at ambient room temperature). Results indicate that speed and environment can affect the observed fatigue life in nuanced ways. An electropotential monitoring technique was demonstrated to characterize fatigue crack growth which may be useful in future investigations.

Autoalgometry: An Important Tool for Pressure Pain Threshold Evaluation.

The term "pain threshold" refers to the measurement of the intensity of a physical stimulus that evokes pain. To estimate the pain threshold, a mechanical or electrical stimulus with increasing intensity is usually applied until the subject under evaluation refers to a pain sensation. This study aims to evaluate the autoalgometric pain threshold as a perfect technique to determine the effects of stimulation rate in relation to both gender and the site of stimulation. In this experimental model, pressure algometry was applied: the subject under evaluation pushed a finger against a small round metal tip, producing and at the same time controlling the intensity of the noxious stimulus. Through autoalgometry, the stimulus intensity was recorded over time, measuring the force change rate applied and studying the subject's behavior on approaching pain. This test was performed with 50 healthy volunteers on two days, applying a fast or slow rate of stimulation. The results described demonstrate that there is a positive correlation between the pressure increase rate and the pressure threshold evaluation. In light of these findings, autoalgometry can be proposed as an objective measure of pressure pain threshold for clinical and research use.

Comparing Rotary Bend Wire Fatigue Test Methods at Different Test Speeds.

Given its relatively simple setup and ability to produce results quickly, rotary bend fatigue testing is becoming commonplace in the medical device industry and is the subject of a new standard test method ASTM E2948-14. Although some research has been conducted to determine if results differ for different rotary bend fatigue test setups or test speeds, these parameters have not been extensively studied together. In this work, we investigate the effects of these two parameters on the fatigue life of three commonly used medical device alloys (ASTM F2063 nitinol, ASTM F138 stainless steel, and ASTM F1058 cobalt chromium). Results with three different rotary bend fatigue test setups revealed no difference in fatigue life among those setups. Increasing test speed, however, between 100 and 35,000 RPM led to an increased fatigue life for all three alloys studied (average number of cycles to fracture increased between 2.0 and 5.1 times between slowest and fastest test speed). Supplemental uniaxial tension tests of stainless steel wire at varying strain rates showed a strain rate dependence in the mechanical response which could in part explain the increased fatigue life at faster test speeds. How exactly strain rate dependence might affect the fatigue properties of different alloys at different alternating strain values requires further study. Given the difference in loading rates between benchtop fatigue tests and in vivo deformations, the potential for strain rate dependence should be considered when designing durability tests for medical devices and in extrapolating results of those tests to in vivo performance.