Horizontal Transport in Ti3C2Tx MXene for Highly Efficient Osmotic Energy Conversion from Saline-Alkali Environments.

Osmotic energy from the ocean has been thoroughly studied, but that from saline-alkali lakes is constrained by the ion-exchange membranes due to the trade-off between permeability and selectivity, stemming from the unfavorable structure of nanoconfined channels, pH tolerance, and chemical stability of the membranes. Inspired by the rapid water transport in xylem conduit structures, we propose a horizontal transport MXene (H-MXene) with ionic sequential transport nanochannels, designed to endure extreme saline-alkali conditions while enhancing ion selectivity and permeability. The H-MXene demonstrates superior ion conductivity of 20.67 S m-1 in 1 M NaCl solution and a diffusion current density of 308 A m-2 at a 10-fold salinity gradient of NaCl solution, significantly outperforming the conventional vertical transport MXene (V-MXene). Both experimental and simulation studies have confirmed that H-MXene represents a novel approach to circumventing the permeability-selectivity trade-off. Moreover, it exhibits efficient ion transport capabilities, addressing the gap in saline-alkali osmotic power generation.

An electrochemical aptamer-sensing strategy based on a Ti3C2Tx MXene synergistic Ti-MOF amplification signal for highly sensitive detection of zearalenone.

A refined electrochemical aptamer sensing technique using PEI@Ti-MOF@Ti3C2Tx-MXene was developed for the sensitive detection of ZEN in food samples. A titanium-based metal-organic skeleton (NH2-MIL-125) was synthesized in situ using 2-aminoterephthalic acid as the organic ligand and tetrabutyl titanate as the metal center, followed by the simultaneous hybridization of Ti3C2Tx-MXene to synthesize a Ti-MOF@Ti3C2Tx-MXene composite material. These composites were subsequently functionalized with PEI and covalently linked to form a sensing platform on gold electrodes. Integrating a metal-organic framework (MOF) with MXene materials not only improved the electrochemical properties compared to those of individual elements but also decreased the stacking effect and increased the number of binding sites for the aptamer. The limit of detection (LOD) of this sensor was 1.64 fg mL-1. Additionally, the sensor could efficaciously detect ZEN in cornmeal and beer samples, exhibiting outstanding stability, reproducibility, and selectivity. This highlighted its effectiveness in applications in quality supervision and food safety.

Cu-Bi Bimetallic Sulfides Loaded on Two-Dimensional Ti3C2Tx MXene for Efficient Electrocatalytic Nitrogen Reduction under Ambient Conditions.

In this paper, Ti3C2Tx MXene/Cu-Bi bimetallic sulfide (Ti3C2Tx/BiCuS2.5) composites were prepared by a simple in situ deposition method for electrocatalytic nitrogen reduction reaction (eNRR). Compared to Ti3C2Tx/Bi2S3 and Ti3C2Tx/CuS, the eNRR performance of Ti3C2Tx/BiCuS2.5 is significantly improved. The results show that Ti3C2Tx/BiCuS2.5 exhibits a NH3 yield of 62.57 µg h-1 mg-1cat. in 0.1 M Na2SO4 at -0.6 V vs reversible hydrogen electrode, and the Faradaic efficiency (FE) reaches 67.69%, which is better than that of Ti3C2Tx/CuS (NH3 yield: 52.26 µg h-1 mg-1cat., FE: 34.15%) and Ti3C2Tx/Bi2S3 (NH3 yield: 54.04 µg h-1 mg-1cat., FE: 37.38%). According to density functional theory calculations, the eNRR at the Ti3C2Tx/BiCuS2.5 surface is the alternating pathway. The 1H NMR experiment of 15N proves that the N of NH3 generated in the experiment originates from N2 passed during the experiment.

Rapid Photothermal-Responsive Soft Hydrogel Actuator Contained Ti3C2Tx MXene and Laponite Clay with Enhanced Mechanical Properties.

Photothermal responsive hydrogels are widely used in bionic soft actuators due to their remote-controlled capabilities and flexibility. However, their weak mechanical properties and limited responsiveness hinder their potential applications. To overcome this, we developed an innovative laponite/MXene/PNIPAm (LxMyPN) nanocomposite hydrogel that is mechanically robust and exhibits excellent photothermally responsive properties based on abundant hydrogen bonds. Notably, laponite clay is used as a co-cross-linking agent to improve the mechanical properties of LxMyPN hydrogel, while MXene nanosheets are added to promote the photothermal responsiveness. The resulting L3M0.4PN nanocomposite hydrogel exhibits enhanced mechanical properties, with a compressive strength of 0.201 MPa, a tensile strength of 90 kPa, and a fracture toughness of 27.25 kJ m-2. In addition, the L3M0.4PN hydrogel displays a deswelling ratio of 73.6% within 60 s and experiences an excellent volume shrinkage of 82.4% under light irradiation. Furthermore, hydrogel actuators with fast response behaviors are constructed and employed as grippers capable of grasping and releasing target objects. Overall, this high-strength and fast-responsive hydrogel actuator is beneficial to paving the way for remote controlled soft robots.

Fast Reduction of 4-Nitrophenol and Photoelectrochemical Hydrogen Production by Self-Reduced Bi/Ti3C2Tx/Bi2S3 Nanocomposite: A Combined Experimental and Theoretical Study.

The distinctive properties of 2D MXenes have garnered significant interest across various fields, including wastewater treatment and photo/electro-catalysis. The integration of inexpensive semiconductor nanostructures with 2D MXenes offers a promising strategy for applications such as wastewater treatment and photoelectrochemical hydrogen production. In this study, we employed an in situ hydrothermal method to immobilize 1D Bi2S3 nanorods and self-reduced metallic bismuth nanoparticles (Bi NPs) onto Ti3C2Tx MXene nanosheets, resulting in the formation of a Bi/Bi2S3/Ti3C2Tx (0D/1D/2D) composite catalyst, which demonstrates an outstanding efficacy in both the reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) and photoelectrochemical hydrogen production. Remarkably, a 4-NP reduction efficiency of 100% was achieved only in 4 min with a reduction rate of 1.14 min-1, which is outstanding, and it is ∼3.8 times faster than pristine Bi2S3 nanorods (0.3 min-1). Furthermore, the photoelectrochemical assessment reveals that the Bi/Bi2S3/Ti3C2Tx catalyst displays remarkable hydrogen evolution reaction (HER) efficiency in an alkaline electrolyte. It exhibits a significantly lower overpotential and Tafel slope of 73 mV and 84 mV/dec, respectively, compared to pristine Bi2S3 nanorods, which are found to be 129 mV and 145 mV/dec under light illumination. The superior reduction performance of 4-NP and charge transfer mechanism is further investigated through density functional theory (DFT) calculations, alongside validation using various microscopic and spectroscopic techniques. Interestingly, the DFT analysis revealed modifications in the partial density of states of Bi2S3 within the band gap region due to the successful anchoring of Ti3C2Tx nanosheets and metallic Bi NPs, facilitating efficient charge transport and separation across the local junctions. Ultraviolet photoelectron spectroscopy provided insights into band alignment and interfacial charge transfer across the Bi/Bi2S3/Ti3C2Tx junction on a microscopic scale. This work is significant for the development of MXene-based hybrid catalysts, and it provides a deeper understanding of the reduction mechanism of organic pollutants and superior charge transport in the hybrid system for photoelectrochemical hydrogen production.

Advancements in Ti3C2Tx MXene Stability: Synergistic Antioxidant Strategies and Their Impact on Long-Lasting Flexible Sensors.

Two-dimensional (2D) transition metal carbides (Ti3C2Tx MXene) have demonstrated substantial application potential across various fields, owing to their excellent metallic conductivity and solution processability. However, the rapid oxidation of Ti3C2Tx in aqueous environments, leading to a loss of stability within mere days, poses a significant obstacle for its practical applications. Herein, we introduce an antioxidant strategy that combines free radical scavenging with surface passivation, culminating in the design and synthesis of imidazolium-based ionic liquids (ILs) incorporating siloxane groups. By deploying a straightforward hydrolysis-addition reaction, we successfully fabricated IL-modified Ti3C2Tx materials (Ti3C2Tx-IL). The Ti3C2Tx -IL not only displayed exceptional conductivity exceeding 3.85 × 104 S/m and hydrophilic contact angles below 45° but also showcased its superior chemical stability and antioxidation mechanisms through various analyses, including visual color change experiments, spectroscopic and energy spectrum characterization, free radical scavenging tests, and density-functional-theory-based molecular simulations. Furthermore, when utilized as a conductive filler in the fabrication of a poly(vinyl alcohol)/nanocellulose fiber (PVA/CNF) composite hydrogel (PCMIL), the resultant sensors exhibited remarkable mechanical performance with up to 535% strain, 1.59 MPa strength, 4.35 MJ/m3 toughness, and a conductivity of 3.40 mS/cm, as well as a high sensitivity gauge factor of 3.3. Importantly, even after 45 days of storage, the PCMIL retained most of its functionalities, demonstrating superior performance in human-machine interaction applications compared to hydrogels made from unmodified Ti3C2Tx. This research establishes a robust antioxidant protection strategy for Ti3C2Tx, offering substantial technical reinforcement for its prospective applications in the realm of flexible electronics and sensing technologies.

Modification of Ti3C2Tx nanostructure with KH2PO4 and chitosan for effective removal of strontium from nuclear waste.

Nanostructure titanium carbide MXene (Ti3C2Tx) was modified with KH2PO4 and chitosan to effectively remove strontium from nuclear wastewater. Nuclear waste includes radionuclides of uranium, thorium, strontium, and cesium, which are classified depending on the concentration of radionuclides. Nuclear waste with a high strontium concentration is the production waste of radiopharmaceutical production centers. Ti3C2Tx was synthesized from Ti3AlC2 using HF40% and HF in situ (MILD-Ti3C2Tx) in 24 h at 313.15 and 333.15 K. Morphology, structure, and functional groups were investigated using the XRD, SEM, EDS, FTIR, and BET analyses. The Sr(II)'s adsorption capacity on Ti3C2Tx-HF and Ti3C2Tx-HF in situ was obtained as 61.9 and 253.5 mg g-1, respectively (temperature, 298.15 K; pH, 7.00; contact time, 180 min; and Sr(II) concentration, 150 mg l-1). Ti3C2Tx-HF in situ showed fourfold adsorption due to more hydroxyl functional groups and larger interlayer spacing. Ti3C2Tx was modified with KH2PO4 and chitosan to investigate the mechanism of change of Sr(II)'s adsorption capacity, which increased to 370 and 284 mg g-1, respectively. The structural results of modified Ti3C2Tx showed that the surface functional groups increased when modified with chitosan. In addition, modification with KH2PO4, through encapsulating large amounts of KH2PO4 between Ti3C2Tx layers, increased the possibility of Sr(II) diffusion between layers and electrochemical interactions with hydroxyl groups, and thus, increased its adsorption. Some experiments were designed to investigate the effect of parameters like initial concentration of Sr(II), contact time, temperature, and pH solution, as well as modified- and unmodified-Ti3C2Tx on adsorbent. The results revealed that the adsorption process of Sr(II) with pristine and modified-Ti3C2Tx follows pseudo-second-order kinetics and Freundlich heterogeneous isotherm model. Freundlich model isotherm indicates the presence of various functional groups on the surface and between the pristine and modified Ti3C2Tx layers. Electrostatic reactions and intra-sphere complexation were the two dominant mechanisms of the adsorption process.

Research Progress on Ammonia Sensors Based on Ti3C2Tx MXene at Room Temperature: A Review.

Ammonia (NH3) potentially harms human health, the ecosystem, industrial and agricultural production, and other fields. Therefore, the detection of NH3 has broad prospects and important significance. Ti3C2Tx is a common MXene material that is great for detecting NH3 at room temperature because it has a two-dimensional layered structure, a large specific surface area, is easy to functionalize on the surface, is sensitive to gases at room temperature, and is very selective for NH3. This review provides a detailed description of the preparation process as well as recent advances in the development of gas-sensing materials based on Ti3C2Tx MXene for room-temperature NH3 detection. It also analyzes the advantages and disadvantages of various preparation and synthesis methods for Ti3C2Tx MXene's performance. Since the gas-sensitive performance of pure Ti3C2Tx MXene regarding NH3 can be further improved, this review discusses additional composite materials, including metal oxides, conductive polymers, and two-dimensional materials that can be used to improve the sensitivity of pure Ti3C2Tx MXene to NH3. Furthermore, the present state of research on the NH3 sensitivity mechanism of Ti3C2Tx MXene-based sensors is summarized in this study. Finally, this paper analyzes the challenges and future prospects of Ti3C2Tx MXene-based gas-sensitive materials for room-temperature NH3 detection.

Stretchable Piezoresistive Pressure Sensor Array with Sophisticated Sensitivity, Strain-Insensitivity, and Reproducibility.

This study delves into the development of a novel 10 by 10 sensor array featuring 100 pressure sensor pixels, achieving remarkable sensitivity up to 888.79 kPa-1, through the innovative design of sensor structure. The critical challenge of strain sensitivity inherent is addressed in stretchable piezoresistive pressure sensors, a domain that has seen significant interest due to their potential for practical applications. This approach involves synthesizing and electrospinning polybutadiene-urethane (PBU), a reversible cross-linking polymer, subsequently coated with MXene nanosheets to create a conductive fabric. This fabrication technique strategically enhances sensor sensitivity by minimizing initial current values and incorporating semi-cylindrical electrodes with Ag nanowires (AgNWs) selectively coated for optimal conductivity. The application of a pre-strain method to electrode construction ensures strain immunity, preserving the sensor's electrical properties under expansion. The sensor array demonstrated remarkable sensitivity by consistently detecting even subtle airflow from an air gun in a wind sensing test, while a novel deep learning methodology significantly enhanced the long-term sensing accuracy of polymer-based stretchable mechanical sensors, marking a major advancement in sensor technology. This research presents a significant step forward in enhancing the reliability and performance of stretchable piezoresistive pressure sensors, offering a comprehensive solution to their current limitations.

Harnessing Holey MXene/Graphene Oxide Heterostructure to Maximize Ion Channels in Lamellar Film for High-Performance Capacitive Deionization.

2D Ti3C2Tx MXene-based film electrodes with metallic conductivity and high pseudo-capacitance are of considerable interest in cutting-edge research of capacitive deionization (CDI). Further advancement in practical use is however impeded by their intrinsic limitations, e.g., tortuous ion diffusion pathway of layered stacking, vulnerable chemical stability, and swelling-prone nature of hydrophilic MXene nanosheet in aqueous environment. Herein, a nanoporous 2D/2D heterostructure strategy is established to leverage both merits of holey MXene (HMX) and holey graphene oxide (HGO) nanosheets, which optimize ion transport shortcuts, alleviate common restacking issues, and improve film's mechanical and chemical stability. In this design, the nanosized in-plane holes in both handpicked building blocks build up ion diffusion shortcuts in the composite laminates to accelerate the transport and storage of ions. As a direct outcome, the HMX/rHGO films exhibit remarkable desalination capacity of 57.91 mg g-1 and long-term stability in 500 mg L-1 NaCl solution at 1.2 V. Moreover, molecular dynamics simulations and ex situ wide angle X-ray scattering jointly demonstrate that the conductive 2D/2D networks and ultra-short ion diffusion channels play critical roles in the ion intercalation/deintercalation process of HMX/rHGO films. The study paves an alternative design concept of freestanding CDI electrodes with superior ion transport efficiency.

Ultralight Hierarchical Fe3O4/MoS2/rGO/Ti3C2Tx MXene Composite Aerogels for High-Efficiency Electromagnetic Wave Absorption.

Aerogel-based composites, renowned for their three-dimensional (3D) network architecture, are gaining increasing attention as lightweight electromagnetic (EM) wave absorbers. However, attaining high reflection loss, broad effective absorption bandwidth (EAB), and ultrathin thickness concurrently presents a formidable challenge, owing to the stringent demands for precise structural regulation and incorporation of magnetic/dielectric multicomponents with synergistic loss mechanisms within the 3D networks. In this study, we successfully synthesized a 3D hierarchical porous Fe3O4/MoS2/rGO/Ti3C2Tx MXene (FMGM) composite aerogel via directional freezing and subsequent heat treatment processes. Owing to their ingenious structure and multicomponent design, the FMGM aerogels, featured with abundant heterogeneous interface structure and magnetic/dielectric synergism, show exceptional impedance matching characteristics and diverse EM wave absorption mechanisms. After optimization, the prepared ultralight (6.4 mg cm-3) FMGM-2 aerogel exhibits outstanding EM wave absorption performance, achieving a minimal reflection loss of -66.92 dB at a thickness of 3.61 mm and an EAB of 6.08 GHz corresponding to the thickness of 2.3 mm, outperforming most of the previously reported aerogel-based absorbing materials. This research presents an effective strategy for fabricating lightweight, ultrathin, highly efficient, and broad band EM wave absorption materials.

Rational Design of Flexible, Self-Supporting, and Binder-Free Prussian White/KetjenBlack/MXene Composite Electrode for Sodium-Ion Batteries with Boosted Electrochemical Performance.

Due to their cost-effectiveness, abundant resources, and suitable working potential, sodium-ion batteries are anticipated to establish themselves as a leading technology in the realm of grid energy storage. However, sodium-ion batteries still encounter challenges, including issues related to low energy density and constrained cycling performance. In this study, a self-supported electrode composed of Prussian white/KetjenBlack/MXene (TK-PW) is proposed. In the TK-PW electrode, the MXene layer is coated with Prussian white nanoparticles and KetjenBlack with high conductivity, which is conducive to rapid Na+ dynamics and effectively alleviates the expansion of the electrode. Notably, the electrode preparation method is uncomplicated and economically efficient, enabling large-scale production. Electrochemical testing demonstrates that the TK-PW electrode retains 74.9% of capacity after 200 cycles, with a discharge capacity of 69.7 mAh·g-1 at 1000 mA·g-1. Furthermore, a full cell is constructed, employing a hard carbon anode and TK-PW cathode to validate the practical application potential of the TK-PW electrode.

CuxO decorated Ti3C2Tx MXene composites for non-enzymatic glucose sensing with large linear ranges.

Ti3C2Tx MXene/CuxO composites were prepared by acid etching combined with electrochemical technique. The abundant active sites on the surface of MXene greatly increase the loading of CuxO nanoparticles, and the synergistic effect between the different components of the composite can accelerate the oxidation reaction of glucose. The results indicate that at the working potential of 0.55 V (vs. Ag/AgCl), the glucose sensor based on Ti3C2Tx MXene/CuxO composite presents large linear concentration ranges from 1 µM to 4.655 mM (sensitivity of 361 µA mM-1 cm-2) and from 5.155 mM to 16.155 mM (sensitivity of 133 µA mM-1 cm-2). The limit of detection is 0.065 µM. In addition, the sensor effectively avoids the oxidative interference of common interfering species such as ascorbic acid, dopamine and uric acid. The sensor has good reproducibility, stability and acceptable recoveries for the detection of glucose in human sweat sample (97.5-103.3%) with RSD values less than 4%. Based on these excellent properties it has great potential for the detection of glucose in real samples.

Maintaining the 2D Structure of MXene via Self-Assembled Monolayers for Efficient Lubrication in High Humidity.

MXene is considered as a promising solid lubricant due to facile shearing ability and tuneable surface chemistry. However, it faces challenges in high-humidity environments where excessive water molecules can significantly impact its 2D structure, thus deteriorating its lubricating properties. In this work, the self-assembled monolayers are formed on MXene by surface chlorination (MXene-Cl) and fluorination (MXene-F), and their friction behaviors in high/low humidity are investigated. The results indicate that MXene-F and MXene-Cl can maintain a relatively constant friction coefficient (CoF) (MXene-F ∼0.76, MXene-Cl ∼0.48) under both high (75%) and low (25%)-relative humidity (RH) environments. Meanwhile, the MXene-F and MXene-Cl display a lower CoF than the pristine MXene (MXene CoF∼1.18) in high humidity. The above phenomena are mainly attributed to the preservation of its 2D layered structure, the increased layer spacing, and superficial partial oxidation for SAMs-functionalized MXene under high humidity during friction. Interestingly, MXene-Cl with moderate water resistance has a lower CoF than that of MXene-F with complete water resistance. The nanostructured water adsorption capacity and larger interlayer spacing of MXene-Cl make it exhibit a lower CoF compared to MXene-F. The findings of this study offer valuable guidance for tailoring MXene by surface chemical functionalization as an efficient solid lubricant in high humidity.

Room temperature NH3 gas sensor based on In(OH)3/Ti3C2Tx nanocomposites.

Industrialization and agricultural demand have both improved human life and led to environmental contamination. Especially the discharge of a lot of poisonous and harmful gases, including ammonia, ammonia pollution has become a pressing problem. High concentrations of ammonia can pose significant threats to both the environment and human health. Therefore, accurate monitoring and detection of ammonia gas are crucial. To address this challenge, we have developed an ammonia gas sensor using In(OH)3/Ti3C2Tx nanocomposites through an in-situ electrostatic self-assembly process. This sensor was thoroughly characterized using advanced techniques like XRD, XPS, BET, and TEM. In our tests, the I/M-2 sensor exhibited remarkable performance, achieving a 16.8% response to 100 ppm NH3 at room temperature, which is a 3.5-fold improvement over the pure Ti3C2Tx MXene sensor. Moreover, it provides swift response time (20 s), high response to low NH3 concentrations (≤ 10 ppm), and excellent long-term stability (30 days). These exceptional characteristics indicate the immense potential of our In(OH)3/Ti3C2Tx gas sensor in ammonia detection.

Interface Engineering via Ti3C2Tx MXene Enabled Highly Efficient Bifunctional NiCoP Array Catalysts for Alkaline Water Splitting.

Developing a non-noble metal-based bifunctional electrocatalyst with high efficiency and stability for overall water splitting is desirable for renewable energy systems. We developed a novel method to fabricate a heterostructured electrocatalyst, comprising a NiCoP nanoneedle array grown on Ti3C2Tx MXene-coated Ni foam (NCP-MX/NF) using a dip-coating hydrothermal method, followed by phosphorization. Due to the abundance of active sites, enhanced electronic kinetics, and sufficient electrolyte accessibility resulting from the synergistic effects of NCP and MXene, NCP-MX/NF bifunctional alkaline catalysts afford superb electrocatalytic performance, with a low overpotential (72 mV at 10 mA cm-2 for HER and 303 mV at 50 mA cm-2 for OER), a low Tafel slope (49.2 mV dec-1 for HER and 69.5 mV dec-1 for OER), and long-term stability. Moreover, the overall water splitting performance of NCP-MX/NF, which requires potentials as low as 1.54 and 1.76 V at a current density of 10 and 50 mA cm-2, respectively, exceeded the performance of the Pt/C∥IrO2 couple in terms of overall water splitting. Density functional theory (DFT) calculations for the NCP/Ti3C2O2 interface model predicted the catalytic contribution to interfacial formation by analyzing the electronic redistribution at the interface. This contribution was also evaluated by calculating the adsorption energetics of the descriptor molecules (H2O and the H and OER intermediates).

Ultrastrong Graphene Sheets Assembled with Nanoconfined Water.

Highly ordered assembly of two-dimensional (2D) nanoplatelets plays a key role in enhancing the mechanical properties of layered nanocomposites. Layer-by-layer (LbL) assembly, vacuum-assisted filtration, and blade coating have been used to fabricate layered nanocomposites. However, the intrinsic wrinkles of 2D nanoplatelets and defects derived from assembling approaches make it difficult to align 2D nanoplatelets. Recently, the team of Prof. Qunfeng Cheng at Beihang University and their collaborator, Prof. Ray H. Baughman at the University of Texas at Dallas developed a novel approach for aligning graphene and Ti3C2Tx MXene nanoplatelets by nanoconfined assembly through continuous vacuum-assisted filtration. The resultant MXene-bridged sheet has ultrastrong mechanical properties and low porosity, providing a new concept for assembling 2D nanoplatelets into aligned and compact high-performance layered nanocomposites.

Ultrasonication-assisted synthesis of transition metal carbide of MXene: an efficient and promising material for photocatalytic organic dyes degradation of rhodamine B and methylene blue in wastewater.

Water pollutants of non-biodegradable toxic aromatic dye including Methylene blue (MB) and Rhodamine (RhB) are extremely carcinogenic thiazines used in various industries such as leather industry, paper industry, and the dyeing industry. The presence of dyes in wastewater causes severe threats to human health that are responsible for various harmful chronic or acute diseases and also shows an adverse impact on the environment as it reduces transparency and is harmful to water microorganisms. To overcome severe issues, many traditional techniques have been used to remove toxic pollutants, but these methods are insufficient to remove chemically stable dyes that remain in the treated wastewater. However, the photocatalytic degradation process is an efficient approach to degrade the dye up to the maximum extent with improved efficiency. Therefore, in this work, a new class of two-dimensional (2D) transition metal carbide of Titanium Carbide (Ti3C2Tx) MXene material was used for the organic dyes degradation such as MB and RhB using a photocatalytic process. A layered structure of hexagonal lattice symmetry of Ti3C2Tx MXene was successfully synthesized from the Titanium Aluminum Carbide of Ti3AlC2 bulk phase using an exfoliation process. Further, the XRD spectrum confirms the transformation of bulk MAX phase having (002) plane at 9.2° to Ti3C2Tx MXene of (002) plane at 8.88° confirms the successful removal of Al layer from MAX phase. A smooth, transparent, thin sheet-like morphology of Ti3C2Tx nanosheet size were found to be in the range of 70 to 150 nm evaluated from TEM images. Also, no holes or damages in the thin sheets were found after the treatment with strong hydrofluoric acid confirms the formation Ti3C2Tx layered sheets. The synthesized Ti3C2Tx MXene possesses excellent photocatalytic activity for the degradation of dyes MB, RhB, and mixtures of MB and RhB dyes. MB dye degraded with a degradation percentage efficiency of 99.32% in 30 min, while RhB dye was degraded upto 98.9% in 30 min. Also, experiments were conducted for degradation of mixture of MB and RhB dyes by UV light, and the degradation percentage efficiency were found to be 98.9% and 99.75% for mixture of MB and RhB dye in 45 min, respectively. Moreover, reaction rate constant (k) was determined for each dye of MB, RhB, and mixtures of MB and RhB and was found to be 0.0215 min-1 and 0.0058 min-1, and for mixtures, it was 0.0020 min-1 and 0.009 min-1, respectively.

Titanium Carbide (Ti3C2Tx) MXene for Sequestration of Aquatic Pollutants.

The rapid expansion of industrialization has resulted in the release of multiple ecological contaminants in gaseous, liquid, and solid forms, which pose significant environmental risks to many different ecosystems. The efficient and cost-effective removal of these environmental pollutants has attracted global attention. This growing concern has prompted the synthesis and optimization of nanomaterials and their application as potential pollutant removal. In this context, MXene is considered an outstanding photocatalytic candidate due to its unique physicochemical and mechanical properties, which include high specific surface area, physiological compatibility, and robust electrodynamics. This review highlights recent advances in shaping titanium carbide (Ti3C2Tx) MXenes, emphasizing the importance of termination groups to boost photoactivity and product selectivity, with a primary focus on engineering aspects. First, a broad overview of Ti3C2Tx MXene is provided, delving into its catalytic properties and the formation of surface termination groups to establish a comprehensive understanding of its fundamental catalytic structure. Subsequently, the effects of engineering the morphology of Ti3C2Tx MXene into different structures, such as two-dimensional (2D) accordion-like forms, monolayers, hierarchies, quantum dots, and nanotubes. Finally, a concise overview of the removal of different environmental pollutants is presented, and the forthcoming challenges, along with their prospective outlooks, are delineated.

Ti3C2 (MXene), an advanced carrier system: role in photothermal, photoacoustic, enhanced drugs delivery and biological activity in cancer therapy.

In the realm of healthcare and the advancing field of medical sciences, the development of efficient drug delivery systems become an immense promise to cure several diseases. Despite considerable advancements in drug delivery systems, numerous challenges persist, necessitating further enhancements to optimize patient outcomes. Smart nano-carriers, for instance, 2D sheets nano-carriers are the recently emerging nanosheets that may garner attention for targeted delivery of bioactive compounds, drugs, and genes to kill cancer cells. Within these advancements, Ti3C2TX-MXene, characterized as a two-dimensional transition metal carbide, has surfaced as a prominent intelligent nanocarrier within nanomedicine. Its noteworthy characteristics facilitated it as an ideal nanocarrier for cancer therapy. In recent advancements in drug delivery research, Ti3C2TX-MXene 2D nanocarriers have been designed to release drugs in response to specific stimuli, guided by distinct physicochemical  parameters. This review emphasized the multifaceted role of Ti3C2TX-MXene as a potential carrier for delivering poorly hydrophilic drugs to cancer cells, facilitated by various polymer coatings. Furthermore, beyond drug delivery, this smart nanocarrier demonstrates utility in photoacoustic imaging and photothermal therapy, further highlighting its significant role in cellular mechanisms.