Green ternary composite of graphitic carbon nitride/TiO2/ polyorthoanisidine for the enhanced photocatalytic treatment of Direct Red 28 for industrial water treatment solutions.

Industrial dye effluent causes significant risks to the environment. The present study was focused on photocatalytic degradation of the dye Direct Red 28 using a ternary composite of graphitic carbon nitride, TiO2, and polyorthoanisidine (g-C3N4/TiO2/POA), prepared by in-situ oxidative polymerization o-anisidine. The synthesized composite g-C3N4/TiO2/POA properties were characterized using different analytical techniques. X-ray diffraction (XRD) results revealed the prominent pattern of TiO2 and g-C3N4 in the composite peak at 2θ° while Fourier transform infrared (FTIR) results provided the confirmation peaks for g-C3N4/TiO2/POA and POA at 1,110 cm-1 and 1,084 cm-1 for C-O-C ether. Scanning electron microscopy (SEM) demonstrated an increase in the average size of the composite up to 428 nm. The energy-dispersive X-ray spectroscopy (EDX) spectrum provided the weight percentages of the C, O, and Ti in the composite were 8.5%, 45.69%, and 45.81%, respectively. The photocatalytic degradation of Direct Red 28 dye under UV irradiation using a composite showed that 86% Direct Red 28 dye was degraded by a 30 mg/L dose of g-C3N4/TiO2/POA in 240 min at pH 2. After four consecutive cycles, the utilized composite showed 79% degradation of Direct Red 28, demonstrating the stability and effectiveness of the g-C3N4/TiO2/POA photocatalyst. The high reusability and efficiency of the g-C3N4/TiO2/POA composite are due to increased light absorption range and reduced e-/h+ recombination rate in the presence of g-C3N4 and POA.

Leveraging Bayesian Optimization Software for Atomic Layer Deposition: Single-Objective Optimization of TiO2 Layers.

We demonstrate the application of free-to-use and easy-to-implement Bayesian optimization (BO) software to streamline atomic layer deposition (ALD) process optimization. By employing machine learning-based Bayesian optimization algorithms, we enhanced the silicon surface passivation quality of titanium dioxide layers deposited using titanium tetraisopropoxide (TTIP). Unlike classical designs of experimental methods, such as Box-Behnken or Plackett-Burman designs, which require a predefined set of experiments and can become resource intensive, BO offers several advantages. It dynamically updates the search strategy based on previous outcomes, allowing for efficient exploration of parameter spaces with fewer experimental runs. This adaptive approach is particularly advantageous in small-scale experiments or laboratories where time, resources, and materials are limited. In a single-objective optimization experiment, we identified constrained search spaces that limited further optimization, underscoring the importance of properly defined parameter bounds prior to the optimization process. Our findings highlight that Bayesian optimization can not only reduce time and resource costs associated with ALD process optimization but also support faster discovery of more optimal ALD process parameters, even with minimal prior knowledge of the deposition process or precursor chemistry.

Enhancing Laser-Induced Graphene via Integration of Gold Nanoparticles and Titanium Dioxide for Sensing and Robotics Applications.

Laser-induced graphene (LIG) is a promising material for various applications due to its unique properties and facile fabrication. However, the electrochemical performance of LIG is significantly lower than that of pure graphene, limiting its practical use. Theoretically, integrating other conductive materials with LIG can enhance its performance. In this study, we investigated the effects of incorporating gold nanoparticles (AuNPs) and titanium dioxide (TiO2) into LIG on its electrochemical properties using ReaxFF molecular dynamics (MD) simulations and experimental validation. We found that both AuNPs and TiO2 improved the work function and surface potential of LIG, resulting in a remarkable increase in output voltage by up to 970.5% and output power density by 630% compared to that of pristine LIG. We demonstrated the practical utility of these performance-enhanced LIG by developing motion monitoring devices, self-powered sensing systems, and robotic hand platforms. Our work provides new insights into the design and optimization of LIG-based devices for wearable electronics and smart robotics, contributing to the advancement of sustainable technologies.

Graphene oxide doping in tropical almond (terminalia catappa L.) fruits extract mediated green synthesis of TiO2 nanoparticles for improved DSSC power conversion efficiency.

The power conversion efficiency (PCE) of a dye-sensitized solar cell (DSSC) device depends on its semiconductor characteristics. Titanium dioxide (TiO2) nanoparticles are a semiconductor material commonly used in the DSSC device whose characteristics depend on the synthesis process. There are many routes to synthesize TiO2, however, they typically involve hazardous approaches, which may cause risk to the environment. Green synthesis is an environmentally friendly alternative method using ecological solvents that eliminates toxic waste and reduces energy consumption. In this work, tropical almond (Terminalia catappa L.) was used as a natural capping agent in the green synthesis to control the growth of TiO2. In addition, graphene oxide (GO) was used as a dopant to increase the performance of DSSC device. The results are convincing, in which the addition of 0.0017 % GO doping in tropical almond extract mediated green synthesis of TiO2 improved the PCE from 0.85 % to 1.72 %. These results suggest that GO-modified TiO2 nanoparticles green synthesized using tropical almond extract have great potential in the fabrication of DSSC devices with good PCE, low cost, and low environmental impact.

Brookite TiO2 as an active photocatalyst for photoconversion of plastic wastes to acetic acid and simultaneous hydrogen production: Comparison with anatase and rutile.

Photoreforming is a clean photocatalytic technology for simultaneous plastic waste degradation and hydrogen fuel production, but there are still limited active and stable catalysts for this process. This work introduces the brookite polymorph of TiO2 as an active photocatalyst for photoreforming with an activity higher than anatase and rutile polymorphs for both hydrogen production and plastic degradation. Commercial brookite successfully converts polyethylene terephthalate (PET) plastic to acetic acid under light. The high activity of brookite is attributed to good charge separation, slow decay and moderate electron trap energy, which lead to a higher generation of hydrogen and hydroxyl radicals and accordingly enhanced photo-oxidation of PET plastic. These results introduce brookite as a stable and active catalyst for the photoconversion of water contaminated with microplastics to value-added organic compounds and hydrogen.

The Influence of Titanium Dioxide (TiO2) Particle Size and Crystalline Form on the Microstructure and UV Protection Factor of Polyester Substrates.

The inclusion of particles in a polymeric substrate to achieve certain properties is a well-known practice. In the case of textile substrates, this practice may deeply affect the structure of the produced yarns, as even a filament with no textile applications can be obtained. In this manuscript, titanium dioxide (TiO2) particles were incorporated into polyester (PET) chips and the influence of these fillers on the properties of yarn and fabric, and the ultraviolet protection factor (UPF) was assessed. For this purpose, rutile and anatase crystalline forms of TiO2, as well as the size of the particles, were evaluated. Moreover, parameters such as mechanical properties, orientation of the macromolecules and thermal behavior were analyzed to ensure that the textile grade is maintained throughout the production process. The results showed that the inclusion of micro- and nanoparticles of TiO2 decreases the molecular weight and tenacity of PET. Also, although orientation and crystallinity varied during the textile process, the resulting heatset fabrics did not present important differences in those parameters. Finally, the attainment of textile-grade PET-TiO2 fabrics with UPF indexes of 50+ with both rutile and anatase and micro- and nano-sized TiO2 forms was demonstrated.

Anchoring Carbon Spheres on Titanium Dioxide Modified Commercial Polyethylene (PE) Separator to Suppress Lithium Dendrites for Lithium Metal Batteries.

Lithium dendrites are easily generated for excessively-solved lithium ions (Li+) inside the lithium metal batteries, which will lead serious safety issues. In this experiment, carbon spheres (CS) are successfully anchored on TiO2 (CS@TiO2) in the hydrothermal polymerization, which is filtrated on the commercial PE separator (CS@TiO2@PE). The negative charge in CS can suppress random diffusion of anions through electrostatic interactions. Density functional theory (DFT) calculations show that CS contributes to the desolvation of Li+, thereby increasing the migration rate of Li+. Furthermore, TiO2 exhibits high affinity to liquid electrolytes and acts as a physical barrier to lithium dendrite formation. CS@TiO2 is a combination of the advantages of CS and TiO2. As results, the Li+ transference number of the CS@TiO2@PE separator can be promoted to 0.63. The Li||Li cell with the CS@TiO2@PE separator exhibits a stable cycle performance for more than 600 h and lower polarization voltage (17 mV) at 1 mA cm-2. The coulombic efficiency (CE) of the Li||Cu cells employe the CS@TiO2@PE separator is 81.63% over 130 cycles. The discharge capacity of LiFePO4||Li cells based on the CS@TiO2@PE separator is 1.73 mAh (capacity retention = 91.53% after 260 cycles). Thus, the CS@TiO2 layer inhibits lithium dendrite formation.

Enhancing Visible-Light Photocatalysis with Pd(II) Porphyrin-Based TiO2 Hybrid Nanomaterials: Preparation, Characterization, ROS Generation, and Photocatalytic Activity.

Novel hybrid TiO2-based materials were obtained by adsorption of two different porphyrins on the surface of nanoparticles-commercially available 5,10,15,20-tetrakis(4-sulfonatophenyl)porphyrin (TPPS) and properly modified metalloporphyrin-5,10,15,20-tetrakis(2,6-difluoro-3-sulfophenyl)porphyrin palladium(II) (PdF2POH). The immobilization of porphyrins on the surface of TiO2 was possible due to the presence of sulfonyl groups. To further elevate the adsorption of porphyrin, an anchoring linker-4-hydroxybenzoic acid (PHBA)-was used. The synthesis of hybrid materials was proven by electronic absorption spectroscopy, dynamic light scattering (DLS), and photoelectrochemistry. Results prove the successful photosensitization of TiO2 to visible light by both porphyrins. However, the presence of the palladium ion in the modifier structure played a key role in strong adsorption, enhanced charge separation, and thus effective photosensitization. The incorporation of halogenated metalloporphyrins into TiO2 facilitates the enhancement of the comprehensive characteristics of the investigated materials and enables the evaluation of their performance under visible light. The effectiveness of reactive oxygen species (ROS) generation was also determined. Porphyrin-based materials with the addition of PHBA seemed to generate ROS more effectively than other composites. Interestingly, modifications influenced the generation of singlet oxygen for TPPS but not hydroxyl radical, in contrast to PdF2POH, where singlet oxygen generation was not influenced but hydroxyl radical generation was increased. Palladium (II) porphyrin-modified materials were characterized by higher photostability than TPPS-based nanostructures, as TPPS@PHBA-P25 materials showed the highest singlet oxygen generation and may be oxidized during light exposure. Photocatalytic activity tests with two model pollutants-methylene blue (MB) and the opioid drug tramadol (TRML)-confirmed the light dose-dependent degradation of those two compounds, especially PdF2POH@P25, which led to the virtually complete degradation of MB.

Exploration of Methodologies for Developing Antimicrobial Fused Filament Fabrication Parts.

Composite 3D printing filaments integrating antimicrobial nanoparticles offer inherent microbial resistance, mitigating contamination and infections. Developing antimicrobial 3D-printed plastics is crucial for tailoring medical solutions, such as implants, and cutting costs when compared with metal options. Furthermore, hospital sustainability can be enhanced via on-demand 3D printing of medical tools. A PLA-based filament incorporating 5% TiO2 nanoparticles and 2% Joncryl as a chain extender was formulated to offer antimicrobial properties. Comparative analysis encompassed PLA 2% Joncryl filament and a TiO2 coating for 3D-printed specimens, evaluating mechanical and thermal properties, as well as wettability and antimicrobial characteristics. The antibacterial capability of the filaments was explored after 3D printing against Gram-positive Staphylococcus aureus (S. aureus, ATCC 25923), as well as Gram-negative Escherichia coli (E. coli, ATCC 25922), and the filaments with 5 wt.% embedded TiO2 were found to reduce the viability of both bacteria. This research aims to provide the optimal approach for antimicrobial and medical 3D printing outcomes.

Black titania by sonochemistry: A critical evaluation of existing methods.

In the field of photocatalysis, the fabrication of black titania is a booming topic, as it offers a system with improved solar light harvesting properties and increased overall efficiency. The darkening of white TiO2 powders can be ascribed to surface hydroxylation, oxygen vacancies, Ti3+ centres, or a combination thereof. A handful of studies suggests these defects can be conveniently introduced by acoustic cavitation, generated during sonochemical treatment of pristine TiO2 powders. In reproducing these studies, P25 TiO2 samples were ultrasonicated for various hours with a power density of 8000 W/L, resulting in powders that indeed became gradually darker with increasing sonication time. However, HAADF-STEM revealed that extensive erosion of the sonotrode tip took place and contaminated the samples, which appeared to be the primary reason for the observed colour change. This was confirmed by UV-Vis DRS and DRIFTS, that showed no significant alteration of the catalyst surface after sonication. EPR measurements showed that only an insignificant fraction of Ti3+ centres were produced, far less than in a TiO2 sample that was chemically reduced with NaBH4. No evidence of the presence oxygen vacancies could be found. The enhanced photocatalytic activities of ultrasonicated materials reported in literature can therefore not be ascribed to the synthesis of actual black (defected) TiO2, but rather to specific changes in morphology as a result of acoustic cavitation. Also, this study underlines the importance of considering probe erosion in sonochemical catalyst synthesis, which is an unavoidable side effect that can have an important impact on the catalyst appearance, properties and performance.

Development of cellulose/hydroxyapatite/TiO2 scaffolds for efficient removal of lead (II) ions pollution: Characterization, kinetic analysis, and artificial neural network modeling.

The utilization of nano-biodegradable composites for removing pollutants and heavy metals in aquatic environments has been widespread. This study focuses on synthesizing cellulose/hydroxyapatite nanocomposites with titanium dioxide (TiO2) via the freeze-drying method for the adsorption of lead ions in aquatic environments. The physical and chemical properties of the nanocomposites, including structure, morphology, and mechanical properties, were analyzed through FTIR, XRD, SEM, and EDS. In addition, parameters affecting the adsorption capacity, such as time, temperature, pH, and initial concentration, were determined. The nanocomposite exhibited a maximum adsorption capacity of 1012 mg⸱g-1, and the second-order kinetic model was found to govern the adsorption process. Additionally, an artificial neural network (ANN) was created using weight percentages (wt%) of nanoparticles included in the scaffold to predict the mechanical behavior, porosity, and desorption of the scaffolds at various weight percentages of hydroxyapatite (nHAP) and TiO2. The results of the ANN indicated that the incorporation of both single and hybrid nanoparticles into the scaffolds improved their mechanical behavior and desorption, as well as increased their porosity.

Titanium dioxide nanoparticles enhance photocurrent generation of cyanobacteria.

Photosynthetic microorganisms such as cyanobacteria can convert photons into electrons, providing ideal eco-friendly materials for converting solar energy into electricity. However, the electrons are hardly transported outside the cyanobacterial cells due to the insulation feature of the cell wall/membrane. Various nanomaterials have been reported to enhance extracellular electron transfer of heterotrophic electroactive microorganisms, but its effect on intact photosynthetic microorganisms remains unclear. In this study, we investigated the effect of six different nanomaterials on the photocurrent generation of cyanobacterium Synechocystis sp. PCC 6803. Among the nanomaterials tested, titanium dioxide (TiO2) nanoparticles increased the photocurrent generation of Synechocystis sp. PCC 6803 up to four-fold at the optimum concentration of 2 mg/mL. Transmission electron microscopy and scanning electron microscopy showed that TiO2 bound to cyanobacterial cells and likely penetrated inside of cell membrane. Photochemical analyses for photosystems showed that TiO2 blocked the electrons transfer downstream in PS I, implying a possible extracellular electron pathway mediated by TiO2. This study provides an alternative approach for enhancing the photocurrent generation of cyanobacteria, showing the potential of photosynthetic-nanomaterial hybrids.

Long-Lasting Electret Melt-Blown Nonwoven Functional Filters Made of Organic/Inorganixc Macromolecular Micron Materials: Manufacturing Techniques and Property Evaluations.

Melt-blown nonwoven fabrics for filtration are usually manufactured using polypropylene, but after a certain time period the middle layer of the mask may have a reduced effect on adsorbing particles and may not be easily stored. Adding electret materials not only increases storage time, but also shows in this study that the addition of electret can improve filtration efficiency. Therefore, this experiment uses a melt-blown method to prepare a nonwoven layer, and adds MMT, CNT, and TiO2 electret materials to it for experiments. Polypropylene (PP) chip, montmorillonite (MMT) and titanium dioxide (TiO2) powders, and carbon nanotube (CNT) are blended and made into compound masterbatch pellets using a single-screw extruder. The resulting compound pellets thus contain different combinations of PP, MMT, TiO2, and CNT. Next, a hot pressor is used to make the compound chips into a high-poly film, which is then measured with differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The optimal parameters are yielded and employed to form the PP/MMT/TiO2 nonwoven fabrics and PP/MMT/CNT nonwoven fabrics. The basis weight, thickness, diameter, pore size, fiber covering ratio, air permeability, and tensile property of different nonwoven fabrics are evaluated in order to have the optimal group of PP-based melt-blown nonwoven fabrics. According to the results of DSC and FTIR measurements, PP and MMT, CNT, and TiO2 are completely mixed, and the melting temperature (Tm), crystallization temperature (Tc) and endotherm area are changed accordingly. The difference in enthalpy of melting changes the crystallization of PP pellets, which in turn changes the fibers. Moreover, the Fourier transform infrared (FTIR) spectroscopy results substantiate that PP pellets are well blended with CNT and MMT, according to the comparisons of characteristic peaks. Finally, the scanning electron microscopy (SEM) observation suggests that with a spinning die temperature of 240 °C and a spinning die pressure lower than 0.01 MPa, the compound pellets can be successfully formed into melt-blown nonwoven fabrics with a 10-micrometer diameter. The proposed melt-blown nonwoven fabrics can be processed with electret to form long-lasting electret melt-blown nonwoven filters.

The Effect of Accelerated Aging on the Molecular Weight and Thermal and Mechanical Properties of Polyester Yarns Containing Ceramic Particles.

The accelerated aging of polyethylene terephthalate (PET) multifilament yarns containing nano or microparticles of titanium dioxide (TiO2), silicon carbide (SiC), or fluorite (CaF2) at a maximum percentage of 2% has been studied. For this, the yarn samples were introduced into a climatic chamber at 50 °C, 50% relative humidity, and an ultraviolet A (UVA) irradiance of 1.4 W/m2. They were then removed from the chamber after periods of between 21 and 170 days of exposure. Subsequently, the variation in weight average molecular weight, number molecular weight, and polydispersity was evaluated by gel permeation chromatography (GPC), the surface appearance was evaluated using scanning electron microscopy (SEM), the thermal properties were evaluated using differential scanning calorimetry (DSC), and the mechanical properties were evaluated using dynamometry. The results showed that, at the test conditions, there was degradation in all of the exposed substrates, possibly due to the excision of the chains that make up the polymeric matrix, which resulted in the variation in the mechanical and thermal properties depending on the type and size of the particle used. This study provides insight into the evolution of the properties of PET-based nano- and microcomposites and might be helpful when selecting materials for specific applications, which is of great interest from an industrial point of view.

The aomogeneous and heterogeneous oxidation of organophosphate esters (OPEs) in the atmosphere: Take diphenyl phosphate (DPhP) as an example.

Organophosphate esters (OPEs) are widely detected in the atmosphere. However, the atmospheric oxidative degradation mechanism of OPEs has not been closely examined. This work took density functional theory (DFT) to investigate the tropospheric ozonolysis of organophosphates, represented by diphenyl phosphate (DPhP), including adsorption mechanisms on the surface of titanium dioxide (TiO2) mineral aerosols and oxidation reaction of hydroxyl groups (·OH) after photolysis. Besides, the reaction mechanism, reaction kinetics, adsorption mechanism, and ecotoxicity evaluation of the transformation products were also studied. At 298 K, the total reaction rate constants kO3, kOH, kTiO2-O3, and kTiO2-OH are 5.72 × 10-15 cm3 molecule-1 s-1, 1.68 × 10-13 cm3 molecule-1 s-1, 1.91 × 10-23 cm3 molecule-1 s-1, and 2.30 × 10-10 cm3 molecule-1 s-1. The atmospheric lifetime of DPhP ozonolysis in the near-surface troposphere is 4 min, much lower than that of hydroxyl radicals (·OH). Besides, the lower the altitude is, the stronger the oxidation is. The TiO2 clusters carry DPhP promoting ·OH oxidation but inhibiting ozonolysis of DPhP. Finally, the main transformation products of this process are glyoxal, malealdehyde, aromatic aldehydes, etc., which are still ecotoxic. The findings shed new light on the atmospheric governance of OPEs.

Creation of a Composite Bioactive Coating with Antibacterial Effect Promising for Bone Implantation.

When creating titanium-containing bone implants, the bioactive coatings that promote their rapid engraftment are important. The engraftment rate of titanium implants with bone tissue depends significantly on the modification of the implant surface. It is achieved by changing either the relief or the chemical composition of the surface layer, as well as a combination of these two factors. In this work, we studied the creation of composite coatings with a two-level (the micro- and nanolevel) hierarchy of the surface relief, which have bioactive and bactericidal properties, which are promising for bone implantation. Using the developed non-lithographic template electrochemical synthesis, a composite coating on titanium with a controlled surface structure was created based on an island-type TiO2 film, silver and hydroxyapatite (HAp). This TiO2/Ag/HAp composite coating has a developed surface relief at the micro- and nanolevels and has a significant cytological response and the ability to accelerate osteosynthesis, and also has an antibacterial effect. Thus, the developed biomaterial is suitable for production of dental and orthopedic implants with improved biomedical properties.

Comparative studies of RSM Box-Behnken and ANN-Anfis fuzzy statistical analysis for seawater biodegradability using TiO2 photocatalyst.

In this approach, a batch reactor was employed to study the degradation of pollutants under natural sunlight using TiO2 as a photocatalyst. The effects of photocatalyst dosage, reaction time and pH were investigated by evaluating the percentage removal efficiencies of total organic carbon (TOC), chemical oxygen demand (COD), biological oxygen demand (BOD) and biodegradability (BOD/COD). Design Expert-Response Surface Methodology Box Behnken Design (BBD) and MATLAB Artificial Neural Network - Adaptive Neuro Fuzzy Inference system (ANN-ANFIS) methods were employed to perform the statistical modelling. The experimental values of maximum percentage removal efficiencies were found to be TOC = 82.4, COD = 85.9, BOD = 30.9% and biodegradability was 0.070. According to RSM-BBD and ANFIS analysis, the maximum percentage removal efficiencies were found to be TOC = 90.3, 82.4; COD = 85.4, 85.9; BOD = 28.9, 30.9% and the biodegradability = 0.074, 0.080 respectively at the pH 7.5, reaction time 300 min and photocatalyst dosage of 4 g L-1. The study reveals both models found to be well predicted as compared with experimental values. The values of R2 for RSM-BBD (0.920) and for ANFIS (0.990) models were almost close to 1. The ANFIS model was found to be marginally better than that of RSM-BBD.

Synthesis and Characterization of TiO2 Thick Films for Glucose Sensing.

In this paper, we present the results of a non-enzymatic electrochemical glucose biosensor based on TiO2. An anatase working electrode was synthesized using the spin coating technique with the polymeric precursor method and dispersed TiO2 nanoparticles. Through scanning electron microscopy, it was observed that the electrode presented an irregular surface with clusters of nanoparticles. Electrochemical characterization indicated that the response was directly related to the morphology of the electrode. In the presence of glucose, the electrode exhibited adsorption behavior toward the molecules, enabling their recognition. The electrode was tested by employing PBS (phosphate buffer solutions) with varying pH values (from 4 to 9), demonstrating its electrochemical stability, even in the presence of glucose. Amperometric characterization was used to determine that the working region appeared from 0.2 mM to 2 mM, with a sensitivity of 4.46 µAcm-2mM-1 in PBS pH 7. The obtained results suggest that TiO2-based electrodes could be used for the detection of glucose concentration in sweat (0.277-1 mM) and saliva (0.23-1.77 mM).

Multi-Functional Materials Based on Cu-Doped TiO2 Ceramic Fibers with Enhanced Pseudocapacitive Performances and Their Dielectric Characteristics.

In this work, pure TiO2 and Cu (0.5, 1, 2%)-doped TiO2 composites prepared by electrospinning technique followed by calcination at 900 °C, and having high pseudocapacitive and dielectric characteristics were reported. These nanocomposites were characterized by scanning electron microscopy, X-ray diffraction, and dynamic water sorption vapor measurements. The structural characterization of these nanostructures highlighted good crystallinity including only the rutile phase. The electrochemical characteristics were investigated by cyclic voltammetry and galvanostatic charge-discharge measurements, which were performed in a KOH electrolyte solution. Among the Cu-doped TiO2 nanostructures that were prepared, the one containing 0.5% Cu exhibited superior electrochemical properties, including high specific gravimetric capacitance of 1183 F·g-1, specific capacitance of 664 F·g-1, energy density of 45.20 Wh·kg-1, high power density of 723.14 W·kg-1, and capacitance retention of about 94% after 100 cycles. The dielectric investigation shows good dielectric properties for all materials, where the dielectric constant and the dielectric loss decreased with the frequency increase. Thus, all the interconnected studies proved that these new materials show manifold ability and real applicative potential as pseudocapacitors and high-performance dielectrics. Future work and perspectives are anticipated for characterizing electrochemical and dielectric properties for materials including larger amounts of Cu dopant.

Photoreactive Coating Material as an Effective and Durable Antimicrobial Composite in Reducing Bacterial Load on Surfaces in Livestock.

Titanium dioxide (TiO2) is a well-known photocatalytic compound that can be used to effectively reduce the presence of pathogens in human and animal hospitals via ROS release. The aim of this study was to investigate the efficacy of a polymer-based composite layer containing TiO2 and zinc oxide (ZnO) against Escherichia coli (E. coli) of animal origin. We showed that the photocatalyst coating caused a significant (p < 0.001) reduction in pathogen numbers compared to the control with an average reduction of 94% over 30 min. We used six light sources of different wattages (4 W, 7 W, 9 W, 12 W, 18 W, 36 W) at six distances (35 cm, 100 cm, 150 cm, 200 cm, 250 cm, 300 cm). Samples (n = 2160) were taken in the 36 settings and showed no significant difference in efficacy between light intensity and distance. We also investigated the influence of organic contaminant that resulted in lower activity as well as the effect of a water jet and a high-pressure device on the antibacterial activity. We found that the latter completely removed the coating from the surface, which significantly (p < 0.0001) reduced its antibacterial potential. As a conclusion, light intensity and distance does not reduce the efficacy of the polymer, but the presence of organic contaminants does.