Effect of halloysite addition on the dynamic mechanical and tribological properties of carbon and glass fiber reinforced hybrid composites.

Composite materials have become prominent in the aerospace, automotive, wind energy, biomedical, and machine tool industries. This has demanded the evaluation of the dynamic mechanical and tribological behaviour of composites to understand their performance and ensure their reliability and safety in varied operating conditions. In this study, the effect of halloysite nano-clay addition on the dynamic mechanical and tribological properties of the carbon/glass hybrid composites was investigated. The composites were produced with the vacuum assisted resin infusion process. by varying the content of halloysite nano-clay (1, 3, and 5 wt%). The dynamic mechanical properties of the manufactured composites were examined at temperatures ranging from 30 °C to 180 °C. The tribological properties of the specimens were assessed by varying the applied load (10, 20, and 30 N), sliding speed (1.5, 3, and 4.5 m/s) and sliding distance (500, 1000, and 1500 m). Box-Behnken design was utilized to optimize the number of experiments. The results showed that the halloysite-added samples had better dynamic mechanical and tribological properties than the carbon/glass hybrid composites. Especially, hybrid composites containing 3 wt% halloysite outperformed the other composites investigated. A scanning electron microscope (SEM) was used to examine the worn surface and wreckage in the investigated composite specimens.

Synovium friction properties are influenced by proteoglycan content.

The synovium plays a crucial role in diarthrodial joint health, and its study has garnered appreciation as synovitis has been linked to osteoarthritis symptoms and progression. Quantitative synovium structure-function data, however, remain sparse. In the present study, we hypothesized that tissue glycosaminoglycan (GAG) content contributes to the low friction properties of the synovium. Bovine and human synovium tribological properties were evaluated using a custom friction testing device in two different cases: (1) proteoglycan depletion to isolate the influence of tissue GAGs in the synovium friction response and (2) interleukin-1 (IL) treatment to observe inflammation-induced structural and functional changes. Following proteoglycan depletion, synovium friction coefficients increased while GAG content decreased. Conversely, synovium explants treated with the proinflammatory cytokine IL exhibited elevated GAG concentrations and decreased friction coefficients. For the first time, a relationship between synovium friction coefficient and GAG concentration is demonstrated. The study of synovium tribology is necessary to fully understand the mechanical environment of the healthy and diseased joint.

Tribological properties of real foods using extended Stribeck curves and their relationship with nutritional and rheological parameters.

The tribological properties of 19 commercial food products, grouped into six categories (yogurt, dressings, spreads, porridges, emulsified sauces, and syrups) were investigated in relation to their rheological (dynamic oscillatory shear test) and nutritional properties (fat, carbohydrate, and protein). A tribological system (a glass ball and three polydimethylsiloxane pins) generated the extended Stribeck curve, monitoring friction factors (f) over an extended range of sliding speed (v) (10-8 to 100 m/s). Tribological parameters (f, v) at four inflection points dividing the frictional regimes (X1, breakaway point between the static and kinetic regimes; X1-X2, boundary; X2-X3, mixed; X3-X4, hydrodynamic regimes) and the slope between X3 and X4 (s) were subjected to principal component analysis and hierarchical clustering on principal components, using rheological and nutritional parameters as quantitative supplementary variables. Tribological patterns were predominantly influenced by viscosity, viscoelasticity, yield stress, fat content, and the presence of particles (e.g., sugar, proteins, and fibers) and pasting materials (e.g., starches and modified starches). The 19 tribological patterns were classified into 3 clusters: low f and s for fat- and/or viscoelastic-dominant foods (Cluster 1), low f and high s for food emulsions and/or those with low extent of shear-thinning (Cluster 2), and high f at the boundary regime either for the most viscous foods or for those in the presence of particulates (Cluster 3). These results suggest that the compositional and rheological properties have a more profound impact on the classification of complex tribological patterns than the categories of food products.

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr.

The Ti-5Al-5V-5Mo-3Cr (Ti-5553) alloy is a relatively novel difficult-to-cut material with limited machinability and tool life analysis available in the literature, and hence requires further investigation. This study focuses on the machining and tribological performance of Ti-5553 under high-speed finish turning (150 m/min, 175 m/min, and 200 m/min) via novel mono/bi-layered PVD-coated WC tools. A base AlTiN coating is used as the reference monolayer coating, with AlCrN, diamond-like ta-C, and TiAlSiN coatings each deposited on top of a base AlTiN coating, totaling four separate coated tools (one monolayer and three bi-layer). Tool life, cutting forces, workpiece surface quality, and tribological chip analysis are among the subjects of investigation in this study. Overall, the AlTiN/AlCrN coated tool outperformed all the other combinations: an improvement of ~19% in terms of tool life in reference to the base AlTiN coating when averaging across the three speeds; lowest surface roughness values: ~0.30, 0.33, and 0.64 µm; as well as the lowest chip back surface roughness values: ~0.80, 0.68, and 0.81 µm at 150, 175, and 200 m/min, respectively. These results indicate that the AlTiN/AlCrN coating is an excellent candidate for industrial applications involving high-speed machining of Ti-5553.

On the Concerning Early Failure of a Short Stem Press-Fit Humeral Component.

INTRODUCTION: Anatomic total shoulder arthroplasty (TSA) is a common surgical intervention for various shoulder pathologies, predominantly glenohumeral osteoarthritis. While generally considered safe and effective, complications remain a challenge. Short stem implants, aim to preserve bone stock and reduce complications. However, concerns about a specific short stem implant (Univers Apex; Arthrex, Naples, FL, USA) have surfaced due to high reported rates relatively early aseptic loosening. METHODS: This retrospective study analyzed 116 consecutive TSA patients with Univers Apex implants from 2004 to 2022. 15 revision cases were assessed for radiographic loosening, and explanted implants were examined for damage using a 0-3 scale. Histopathological analysis evaluated cellular responses to wear debris. RESULTS: Of the patients, 13% (15/116) required revision at 23.2 months on average. A distinct radiographic loosening pattern was identified, with humeral component subsidence and thinning of the proximal humeral cortex. Histopathology revealed a robust inflammatory response to wear debris, with a potential association between macrophage infiltration, hinge damage, and polyethylene wear. CONCLUSION: This study reveals a notable rate of early aseptic humeral loosening with the Univers Apex short stem implant, emphasizing concerns raised in previous reports and providing a potential explanation for the high rate of early failure. Surgeons should exercise caution and closely monitor patients with this implant design.

Effects of dispersing media on the rheological and tribological properties of basil seed mucilage-based thickened liquids.

The development of thickening powders for the management of dysphagia is imperative due to the rapid growth of aging population and prevalence of the dysphagia. One promising thickening agent that can be used to formulate dysphagia diets is basil seed mucilage (BSM). This work investigates the effects of dispersing media, including water, milk, skim milk, and apple juice, on the rheological and tribological properties of the BSM-thickened liquids. Shear rheology results revealed that the thickening ability of BSM in these media in ascending order is milk < skim milk ≈ apple juice < water. On the other hand, extensional rheology demonstrated that the longest filament breakup time was observed when BSM was dissolved in milk, followed by skim milk, water, and apple juice. Furthermore, tribological measurements showed varying lubrication behavior, depending on the BSM concentration and dispersing media. Dissolution of BSM in apple juice resulted in the most superior lubrication property compared with that in other dispersing media. Overall, this study provides insights on BSM's application as a novel gum-based thickening powder in a range of beverages and emphasizes how important it is for consumers to have clear guidance for the use of BSM in dysphagia management.

Correlation of rheology and oral tribology with sensory perception of commercial hazelnut and cocoa-based spreads.

This study examined the effects of spread formulation and the structural/lubricant properties of six different commercial hazelnut and cocoa spreads on sensory perception. Rheology, tribology, and quantitative descriptive analysis (QDA) was assessed by also evaluating the correlation coefficients between the quality descriptor and the rheological and textural parameters. The viscosity was evaluated at different temperatures to better simulate conditions before and after ingestion. Tribological analysis was executed at 37°C to mimic the human oral cavity. The effect of saliva presence and the number of runs on tribological behaviors was investigated. Moreover, textural, calorimetric, and particle size distribution measurements were performed to reinforce the correlation between structural/thermal parameters (e.g., firmness, stickiness, sugar melting point) and sensory aspects. "Visual viscosity," defined as a sensory attribute evaluated prior to consumption, negatively correlated with apparent viscosity measured at 20°C and 10 s-1, whereas "body," defined during oral processing and related to creaminess, positively correlated with apparent viscosity measured at 37°C and 50 s-1. These attributes were mainly influenced by particulate microstructure and solid volume fraction within the formulation. Textural stickiness positively correlated with sensory "adhesiveness" and was related to fat composition and milk powder addition, while "sweetness" was related to sucrose content and sugar melting enthalpy. Tribological data provided meaningful information related to particle-derived attributes, as well as after-coating perception (fattiness/oiliness), thus better predicting food evolution during oral consumption.

Addressing astringency of grape seed extract by covalent conjugation with lupin protein.

Astringency of phenolic-rich foods is a key tactile perception responsible for acceptability/rejection of plant extracts as ingredients in formulations. Covalent conjugation of phenolic extracts with plant proteins might be a promising strategy to control astringency, but suffers from a lack of mechanistic understanding from the lubrication point of view. To shed light on this, this ex vivo study evaluated the effect of conjugation of a phenolic grape seed extract (GSE) with legume protein (lupin, LP) on tribological and surface adsorption performance of GSE in the absence and presence of human saliva (ex vivo). Tribological results confirmed GSE had an inferior lubrication capacity as compared to LP. The lubrication performance of LP-GSE dispersions was comparable to their corresponding LP dispersion (p > 0.05) when covalently conjugated with LP (LP-GSE) with increasing LP:GSE ratio up to 1:0.04 w/w and at a specific degree of conjugation (DC: 2%). Tribological and surface adsorption measurements confirmed the tendency of GSE to interact with human saliva (ex vivo, n = 17 subjects), impairing the lubricity of salivary films. The covalent bonding of LP to GSE hindered GSE's interaction with human saliva, implying the potential influence of covalent conjugation on attenuating astringency. LP appeared to compete with human saliva for surface adsorption and governed the lubrication behaviour in LP-GSE dispersions. Findings from this study provide valuable knowledge to guide the rational design of sustainable, functional foods using conjugation of phenolics with plant proteins to incorporate larger proportions of health-promoting phenolics while controlling astringency, which needs validation by sensory trials.

On the Design, Fabrication, and Characterization of a Novel Thin-Film Electrode Array for Use in Cochlear Implants.

Thin-film electrode arrays (TFEAs) have been developed as an alternative to conventional electrode arrays (CEAs) used in cochlear implants. However, TFEAs produced by microfabrication techniques have not yet been used clinically because their structural and mechanical properties are far from those of CEAs. The aim of this study is to design, fabricate, and investigate the mechanical and tribological behavior and evaluate the performance of different TFEA designs. Finite Element Analysis (FEA) is performed to determine the elastic properties of several designs. A custom-build experimental setup is designed to observe the tribological behavior in different speeds and environments where frictional (lateral) and vertical force (normal force) are measured on a flat surface and within artificial cochlea. According to the FEA results, the maximum stiffness of the CEA is 37.93 mN/mm and 0.363 mN/mm and TFEA-4 has a maximum stiffness of 39.08 mN/mm and 0.306 mN/mm in the longitudinal and transverse axes, respectively. It is shown experimentally that adding a dummy wire to the carrier of the EA enhances both its longitudinal and transverse stiffness, thereby postponing the initiation of dynamic sliding due to the elevated buckling limit. It is also revealed that the type of TFEA support structure affects both normal and frictional forces, as well as the coefficient of friction.

Tribological Properties of Composites Based on Single-Component Powdered Epoxy Matrix Filled with Graphite.

Composites based on powdered single-component epoxy matrix are an alternative technological solution for composites produced using liquid epoxy resins. This article describes in detail the process of producing graphite-reinforced composites for tribological applications. The advantages and disadvantages of technological processes where the matrix is a single-component epoxy powder were demonstrated, and the properties of the obtained materials were examined. A series of composite materials with the graphite filler with sizes below 10 µm and below 45 µm and weight additions of 5, 10, 20, 30% were produced. Mechanical tests and tribological tests conducted with the pin-on-block method were performed, and the mechanism of tribological wear was described. The conducted research allowed us to conclude that the incorporation of graphite, regardless of particle size, above 10% by weight results in a significant reduction in the friction coefficient (approximately 40-50% lower than in unfilled epoxy resin), which is beneficial in the production of cheap self-lubricating materials.

Study on the Tribological Properties of DIN 16MnCr5 Steel after Duplex Gas-Nitriding and Pack Boriding.

DIN 16MnCr5 is commonly used in mechanical engineering contact applications such as gears, joint parts, shafts, gear wheels, camshafts, bolts, pins, and cardan joints, among others. This study examined the microstructural and mechanical properties and tribological behavior of different surface treatments applied to DIN 16MnCr5 steel. The samples were hardened at 870 °C for 15 min and then quenched in water. The surface conditions evaluated were as follows: quenched and tempered DIN 16MnCr5 steel samples without surface treatments (control group), quenched and tempered DIN 16MnCr5 steel samples with gas-nitriding at 560 °C for 6 h, quenched and tempered DIN 16MnCr5 steel samples with pack boriding at 950 °C for 4 h, and quenched and tempered DIN 16MnCr5 steel samples with duplex gas-nitriding and pack boriding. Microstructure characterization was carried out using metallographic techniques, optical microscopy, scanning electron microscopy with energy-dispersive spectroscopy, and X-ray diffraction. The mechanical properties were assessed through microhardness and elastic modulus tests using nanoindentation. The tribological behavior was evaluated using pin-on-disc tests following the ASTM G99-17 standard procedure under dry sliding conditions. The results indicated that the surface treated with duplex gas-nitriding and pack boriding exhibited the highest wear resistance and a reduced coefficient of friction due to improved mechanical properties, leading to increased hardness and elastic modulus.

Use of Heat-Applied Coatings to Reduce Wear on Agricultural Machinery Components.

This article presents the effect of the conditions of abrasive compounds on the wear of samples made by different methods. The 28MnB5 steel was used, which is intended for agricultural components, to which two arc and laser coatings were applied. The study included the analysis of microstructure, microhardness, roughness, and tribological experiments on a dedicated stand. The arc coating was found to significantly improve the tribological properties compared to the samples without the coating. Varied wear results were obtained for the laser coating depending on the parameters of the abrasive compound. Studies of the surface roughness of the samples showed that the concentration and pH of the abrasives have a significant effect on the changes in the surface parameters after the tribological tests. The results of the tribological experiments indicated that wear resistance for some of the abrasive mass conditions was improved by the application of heat-applied coatings. In addition, it was found that the power consumption on the stand was the highest for abrasive mass conditions of a 10% moisture content and a pH of 10. For these test conditions, the mass loss was four times higher than for the parameter with W0% and pH7. The energy consumption of the stand was 60 kWh lower for this variant than for the parameter with W10% and pH10. The results of the study have important practical applications that can help in the selection of materials for agricultural machinery components, depending on the abrasive mass conditions.

Laboratory Tests on the Possibility of Using Flax Fibers as a Plant-Origin Reinforcement Component in Composite Friction Materials for Vehicle Braking Systems.

Braking systems are extremely important in any vehicle. They convert the kinetic energy of motion into thermal energy that is dissipated into the atmosphere. Different vehicle groups have different nominal and maximum speeds and masses, so the amount of thermal energy that needs to be absorbed by the friction pads and then dissipated can vary significantly. Conventional friction materials are composite materials capable of withstanding high temperatures (in the order of 500-600 °C) and high mechanical loads resulting from braking intensity and vehicle weight. In small vehicles traveling at low speeds, where both the amount of thermal energy and its density are limited, the use of slightly weaker friction materials with better ecological properties can be considered. This work proposes a prototype composite friction material using flax fibers as reinforcement instead of the commonly used aramid. A number of samples were prepared and subjected to laboratory tests. The samples were prepared using components of plant origin, specifically flax fibers. This component acted as reinforcement in the composite friction material, replacing aramid commonly used for this purpose. The main tribological characteristics were determined, such as the values of the coefficients of friction and the coefficients of abrasive wear rate. For this purpose, an authorial method using ball-cratering contact was used. The results were analyzed using statistical methods. It was found that the composite material using flax fibers does not differ significantly in its tribological properties from conventional solutions; so, it can be assumed that it can be used in the vehicle's braking system.

Heterogeneous distribution of viscosupplements in vivo is correlated to ex vivo frictional properties of equine cartilage.

Intra-articular injections of hyaluronic acid (HA) are the cornerstone of osteoarthritis (OA) treatments. However, the mechanism of action and efficacy of HA viscosupplementation are debated. As such, there has been recent interest in developing synthetic viscosupplements. Recently, a synthetic 4 wt% polyacrylamide (pAAm) hydrogel was shown to effectively lubricate and bind to the surface of cartilage in vitro. However, its ability to localize to cartilage and alter the tribological properties of the tissue in a live articulating large animal joint is not known. The goal of this study was to quantify the distribution and extent of localization of pAAm in the equine metacarpophalangeal or metatarsophalangeal joint (fetlock joint), and determine whether preferential localization of pAAm influences the tribological properties of the tissue. An established planar fluorescence imaging technique was used to visualize and quantify the distribution of fluorescently labeled pAAm within the joint. While the pAAm hydrogel was present on all surfaces, it was not uniformly distributed, with more material present near the site of the injection. The lubricating ability of the cartilage in the joint was then assessed using a custom tribometer across two orders of magnitude of sliding speed in healthy synovial fluid. Cartilage regions with a greater coverage of pAAm, that is, higher fluorescent intensities, exhibited friction coefficients nearly 2-fold lower than regions with lesser pAAm (Rrm = -0.59, p < 0.001). Collectively, the findings from this study indicate that intra-articular viscosupplement injections are not evenly distributed inside a joint, and the tribological outcomes of these materials is strongly determined by the ability of the material to localize to the articulating surfaces in the joint.

Novel Pickering bigels stabilized by whey protein microgels: Interfacial properties, oral sensation and gastrointestinal digestive profiles.

In the ongoing quest to formulate sensory-rich, low-fat products that maintain structural integrity, this work investigated the potential of bigels, especially those created using innovative Pickering techniques. By harnessing the unique properties of whey protein isolate (WPI) and whey protein microgel (WPM) as interfacial stabilizers, WPM-based Pickering bigels exhibited a remarkable particle localization at the interface due to specific intermolecular interactions. The rise in protein concentration not only intensified particle coverage and interface stabilization but also amplified attributes like storage modulus, yield stress, and adhesiveness, owing to enhanced intermolecular forces and a compact gel matrix. Impressively, WPM-based Pickering bigels outshone in practical applications, showcasing exceptional oil retention during freeze-thaw cycles and extended flavor release-a promising indication for frozen food product applications. Furthermore, these bigels underwent a sensory evolution from a lubricious texture at lower concentrations to a stable plateau at higher ones, offering an enriched consumer experience. In a comparative digestibility assessment, WPM-based Pickering bigels demonstrated superior prowess in decelerating the release of free fatty acids, indicating slowed lipid digestion. This study demonstrates the potential to fine-tune oral sensations and digestive profiles in bigels by modulating Pickering particle concentrations.

Covalent organic frameworks in tribology - A perspective.

Two-dimensional covalent organic frameworks (2D COFs) are an emerging class of crystalline porous materials formed through covalent bonds between organic building blocks. COFs uniquely combine a large surface area, an excellent stability, numerous abundant active sites, and tunable functionalities, thus making them highly attractive for numerous applications. Especially, their abundant active sites and weak interlayer interaction make these materials promising candidates for tribological research. Recently, notable attention has been paid to COFs as lubricant additives due to their excellent tribological performance. Our review aims at critically summarizing the state-of-art developments of 2D COFs in tribology. We discuss their structural and functional design principles, as well as synthetic strategies with a special focus on tribology. The generation of COF thin films is also assessed in detail, which can alleviate their most challenging drawbacks for this application. Subsequently, we analyze the existing state-of-the-art regarding the usage of COFs as lubricant additives, self-lubrication composite coatings, and solid lubricants at the nanoscale. Finally, critical challenges and future trends of 2D COFs in tribology are outlined to initiate and boost new research activities in this exciting field.

2D materials for Tribo-corrosion and -oxidation protection: A review.

The recent rise of 2D materials has extended the opportunities of tuning a variety of properties. Tribo-corrosion, the complex synergy between mechanical wear and chemical corrosion, poses significant challenges across numerous industries where materials are subjected to both tribological stressing and corrosive environments. This intricate interplay often leads to accelerated material degradation and failure. This review critically assesses the current state of utilizing 2D nanomaterials to enhance tribo-corrosion and -oxidation behavior. The paper summarizes the fundamental knowledge about tribo-corrosion and -oxidation mechanisms before assessing the key contributions of 2D materials, including graphene, transition metal chalcogenides, hexagonal boron nitride, MXenes, and black phosphorous, regarding the resulting friction and wear behavior. The protective roles of these nanomaterials against corrosion and oxidation are investigated, highlighting their potential in mitigating material degradation. Furthermore, we delve into the nuanced interplay between mechanical and corrosive factors in the specific application of 2D materials for tribo-corrosion and -oxidation protection. The synthesis of key findings underscores the advancements achieved through integrating 2D nanomaterials. An outlook for future research directions is provided, identifying unexplored avenues, and proposing strategies to propel the field forward. This analysis aims at guiding future investigations and developments at the dynamic intersection of 2D nanomaterials, tribo-corrosion, and -oxidation protection.

Assessing friction and damage of cell monolayers on soft substrates in vitro.

In the area of surgical applications, understanding the interaction between medical device materials and tissue is important since this interaction may cause complications. The interaction often consists of a cell monolayer touching the medical device that can be mimicked in vitro. Prominent examples of this are contact lenses, where epithelial cells interact with the contact lens, or stents and catheters, which are in contact with endothelial cells. To investigate those interactions, in previous studies, expensive microtribometers were used to avoid pressures in the contact area far beyond physiologically relevant levels. Here, we aim to present a new methodology that is cost- and time-efficient, more accessible than those used previously and allows for the application of more realistic pressures, while permitting a quantification of the damage caused to the monolayer. For this, a soft polydimethylsiloxane is employed that better mimics the mechanical properties of blood vessels than materials used in other studies. Furthermore, a technique to account for misalignments within the experiment set-up is presented. This is carried out using the raw spatial and force data recorded by the tribometer and adjusting for misalignments. The methodology is demonstrated using an endothelial cell (human umbilical vein endothelial cells) monolayer.

Deep Learning Model for Cosmetic Gel Classification Based on a Short-Time Fourier Transform and Spectrogram.

Cosmetics and topical medications, such as gels, foams, creams, and lotions, are viscoelastic substances that are applied to the skin or mucous membranes. The human perception of these materials is complex and involves multiple sensory modalities. Traditional panel-based sensory evaluations have limitations due to individual differences in sensory receptors and factors such as age, race, and gender. Therefore, this study proposes a deep-learning-based method for systematically analyzing and effectively identifying the physical properties of cosmetic gels. Time-series friction signals generated by rubbing the gels were measured. These signals were preprocessed through short-time Fourier transform (STFT) and continuous wavelet transform (CWT), respectively, and the frequency factors that change over time were distinguished and analyzed. The deep learning model employed a ResNet-based convolution neural network (CNN) structure with optimization achieved through a learning rate scheduler. The optimized STFT-based 2D CNN model outperforms the CWT-based 2D and 1D CNN models. The optimized STFT-based 2D CNN model also demonstrated robustness and reliability through k-fold cross-validation. This study suggests the potential for an innovative approach to replace traditional expert panel evaluations and objectively assess the user experience of cosmetics.

Tribocorrosion of 3D printed dental implants: An overview.

With the advancements in dental science and the growing need for improved dental health, it has become imperative to develop new implant materials which possess better geometrical, mechanical, and physical properties. The oral environment is a corrosive environment and the relative motion between the teeth also makes the environment more hostile. Therefore, the combined corrosion and tribology commonly known as tribocorrosion of implants needs to be studied. The complex shapes of the dental implants and the high-performance requirements of these implants make manufacturing difficult by conventional manufacturing processes. With the advent of additive manufacturing or 3D-printing, the development of implants has become easy. However, the various requirements such as surface roughness, mechanical strength, and corrosion resistance further make the manufacturing of implants difficult. The current paper reviews the various studies related to3D-printed implants. Also, the paper tries to highlight the role of 3D-Printing can play in the area of dental implants. Further studies both experimental and numerical are needed to devise optimized conditions for 3D-printing implants to develop implants with improved mechanical, corrosion, and biological properties.