RESUMO
This study focused on synthesizing a cellulose-based hydrogel nanocomposite as a green hydrogel by adding a microcrystalline cellulose (MC) solution to carboxymethyl cellulose sodium (CMC-Na) with citric acid as a cross-linker. Y2O3 nanoparticles were incorporated during hydrogel preparation in different ratios (0.00% (0 mmol), 0.03% (0.017 mmol), 0.07% (0.04 mmol) and 0.10% (0.44 mmol)). FTIR analysis confirmed the cross-linking reaction, while XRD analysis revealed the hydrogels' amorphous nature and identified sodium citrate crystals formed from the reaction between citric acid and CMC-Na. The swelling test in deionized water (pH 6.5) at 25 °C showed a maximum swelling percentage of 150% after 24 h in the highest nanoparticle ratio. The resulting cellulose hydrogels were flexible and exhibited significant antibacterial activity against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli). The synthesized cellulose-based hydrogel nanocomposites are eco-friendly and suitable for medical applications.
RESUMO
Zinc metal batteries have recently emerged as a promising stable and reversible anode aqueous battery. However, due to the serious dendrite problem and hydrogen evolution problem of the zinc metal anode, the practical application of the zinc metal battery is limited. Here, we propose Y2O3 as an effective coating, which inhibits hydrogen evolution and side reactions by physical isolation and simultaneously prevents dendrite growth by ensuring a uniform Zn-ion flux and fast transport channels generated by Maxwell-Wagner polarization, thus improving the stability of batteries. Meanwhile, in situ/ex situ characterizations and different simulations are conducted to investigate in detail the effect of Maxwell-Wagner polarization on the performance of Zn metal batteries. The symmetric Y2O3@Zn anode system exhibits a stable electroplating/stripping performance over 780 h and enables the Zn battery to achieve a Coulombic efficiency of up to 99.81% over 1000 cycles by reducing side reactions. The Y2O3@Zn||MnO2 full cell delivers a high energy density of 301.42 Wh kg-1 at a power density of 205.04 W kg-1. The work provides insights into the reversibility and stability of zinc anodes and provides a promising way to promote the practical application of Zn metal batteries.
RESUMO
The structural, surface, and upconversion (UC) luminescence properties of Y2O3:Ho3+,Yb3+ films grown by pulsed laser deposition, for different numbers of laser pulses, were studied. The crystallinity, surface, and UC luminescence properties of the thin films were found to be highly dependent on the number of laser pulses. The X-ray powder diffraction analysis revealed that Y2O3:Ho3+,Yb3+ films were formed in a cubic structure phase with an Ia 3 ¯ space group. The thicknesses of the films were estimated by using cross-sectional scanning electron microscopy, depth profiles using X-ray photoelectron spectroscopy (XPS), and the Swanepoel method. The high-resolution XPS was used to determine the chemical composition and oxidation states of the prepared films. The UC emissions were observed at 538, 550, 666, and 756 nm, assigned to the 5F4 â 5I8, 5S2 â 5I8, 5F5 â 5I8, and 5S2 â 5I7 transitions of the Ho3+ ions. The power dependence measurements confirmed the involvement of a two-photon process in the UC process. The color purity estimated from the Commission International de I'Eclairage coordinates confirmed strong green UC emission. The results suggested that the Y2O3:Ho3+,Yb3+ UC transparent films are good candidates for various applications, including solar cell applications.
RESUMO
We study concentration quenching and energy transfer mechanisms of yttrium oxide (Y2O3) nanomaterials doped with different concentrations (0-5 mol%) of cerium (Ce). Photoluminescence (PL) spectra recorded under an excitation wavelength of 350 nm show a broad emission band at â¼ 406 nm and a feeble emission band at â¼ 463 nm in the undoped Y2O3 sample. The doping of Ce in Y2O3 induced multiple PL peaks within the blue-green region of the spectrum in all the doped samples with the peak at â¼ 466 nm being notably the prominent one. This prominent emission band exhibits a decrease in intensity with increasing Ce concentration due to concentration quenching. Analysis of Time-resolved photoluminescence (TRPL) spectra reveal that the average emission lifetime of Ce-doped Y2O3 is shorter than that of the undoped Y2O3 sample. The concentration quenching effect and the decrease of average emission lifetime of the dominant emission band are explained on the basis of energy transfer from the host Y2O3 to the Ce3+ ion centres. The critical quenching concentration of Ce3+ ion in Y2O3:Ce phosphor was identified to be 1 mol% and the critical transfer distance was estimated to be 23.74 Å. Analysis reveal that the concentration quenching mechanism involves nearest-neighbour interaction.
RESUMO
Self-made agglomerated nanometer CeO2-Y2O3-ZrO2 (CYSZ) powders for plasma spray-physical vapor deposition (PS-PVD) were prepared by spray-drying, followed by calcination treatment at four different temperatures (600 °C, 700 °C, 800 °C, 900 °C). The physical properties, microstructure, and phase composition of the calcined powders were investigated using a laser particle size analyzer, scanning electron microscopy (SEM), and X-ray diffraction (XRD). The results showed that compared to the agglomerated powders obtained through spray-drying, the particle size of the agglomerated powders changed with increasing calcination temperature, accompanied by an increase in the self-bonding force of the agglomerated powder particles. The proper calcination temperature improved the sprayability of the powders. Additionally, with the increase in the calcination temperature, a transformation from the m-phase to the t-phase occurred in the powder, with Ce4+ partially entering the Zr lattice to form the t-Zr0.84Ce0.16O2 phase, which facilitated the suppression of the m-phase and improved the high-temperature phase stability. It was also found that the PS-PVD coatings prepared using the aforementioned powders exhibited coarser columnar structures with increasing powder calcination temperature.
RESUMO
In this study, a Y2O3 insulator was fabricated via the sol-gel process and the effect of precursors and annealing processes on its electrical performance was studied. Yttrium(III) acetate hydrate, yttrium(III) nitrate tetrahydrate, yttrium isopropoxide oxide, and yttrium(III) tris (isopropoxide) were used as precursors, and UV/ozone treatment and high-temperature annealing were performed to obtain Y2O3 films from the precursors. The structure and surface morphologies of the films were characterized via grazing-incidence X-ray diffraction and scanning probe microscopy. Chemical component analysis was performed via X-ray spectroscopy. Electrical insulator characteristics were analyzed based on current density versus electrical field data and frequency-dependent dielectric constants. The Y2O3 films fabricated using the acetate precursor and subjected to the UV/ozone treatment showed a uniform and flat surface morphology with the lowest number of oxygen vacancy defects and unwanted byproducts. The corresponding fabricated capacitors showed the lowest current density (Jg) value of 10-8 A/cm2 at 1 MV/cm and a stable dielectric constant in a frequency range of 20 Hz-100 KHz. At 20 Hz, the dielectric constant was 12.28, which decreased to 10.5 at 105 Hz. The results indicate that high-quality, high-k insulators can be fabricated for flexible electronics using suitable precursors and the suggested low-temperature fabrication methods.
RESUMO
The in situ measurement technique for a metal/metal-oxide mixture at extra-high temperature above 2000â K has been desired in the field of nuclear safety engineering. In the present study, we succeeded in simultaneous XAFS-XRD measurements of the Zr oxidation [Zr + O â Zr(O) + ZrO2] up to 1952â K and ZrO2-Y2O3 reaction from 1952 to 2519â K. The chemical shift during Zr oxidation was observed in the absorption spectra around the Zr K-edge, and the interatomic cation-cation and cation-oxygen distances obtained by the fitting analysis of EXAFS during the Y2O3-ZrO2 reaction are explained. Also, the temperature dependency of the anharmonic effect was investigated by comparing the fitted second- and third-order cumulants with the theoretical ones in which the Morse potential was applied as an interatomic potential, giving a good explanation about the local structure dynamics. Finally, the applicability of the developed system to investigation of nuclear fuel materials, such as UO2-Zr, is discussed.
RESUMO
Solar cells have been developed as a highly efficient source of alternative energy, collecting photons from sunlight and turning them into electricity. On the other hand, ultraviolet (UV) radiation has a substantial impact on solar cells by damaging their active layers and, as a result, lowering their efficiency. Potential solutions include the blocking of UV light (which can reduce the power output of solar cells) or converting UV photons into visible light using down-conversion optical materials. In this work, we propose a novel hydrophobic coating based on a polydimethylsiloxane (PDMS) layer with embedded red emitting Y2O3:Eu3+ (quantum yield = 78.3%) particles for UV radiation screening and conversion purposes. The favorable features of the PDMS-Y2O3:Eu3+ coating were examined using commercially available polycrystalline silicon solar cells, resulting in a notable increase in the power conversion efficiency (PCE) by ~9.23%. The chemical and UV stability of the developed coatings were assessed by exposing them to various chemical conditions and UV irradiation. It was found that the developed coating can endure tough environmental conditions, making it potentially useful as a UV-protective, water-repellent, and efficiency-enhancing coating for solar cells.
RESUMO
Microspheres composed of Y-containing materials are effective agents for cancer radioembolization therapy using ß-rays. The distribution and dynamics of these microspheres in tissues can be easily determined by providing the microspheres with an imaging function. In addition, the use of quantum dots will enable the detection of microspheres at the individual particle level with high sensitivity. In this study, core - shell quantum dots were bound to chemically modified yttria microspheres under various conditions, and the effect of reaction conditions on the photoluminescence properties of the microspheres was investigated. The quantum dots were immobilized on the surfaces of the microspheres through dehydration - condensation reactions between the carboxy groups of quantum dots and the amino groups of silane-treated microspheres. As the reaction time increased, the photoluminescence peak blue shifted, and the photoluminescence intensity and lifetime decreased. Therefore, a moderate period of the immobilization process was optimal for imparting effective photoluminescence properties. This study is expected to facilitate particle-level tracking of microsphere dynamics in biological tissues for the development of minimally invasive cancer radiotherapy of deep-seated tumors.
We have established a method to immobilize quantum dots on yttria microspheres for cancer radiotherapy and revealed that photoluminescence intensity can be optimized by controlling the immobilization treatment time.
RESUMO
Herein, sol-gel-processed Y2O3 resistive random-access memory (RRAM) devices were fabricated. The top electrodes (TEs), such as Ag or Cu, affect the electrical characteristics of the Y2O3 RRAM devices. The oxidation process, mobile ion migration speed, and reduction process all impact the conductive filament formation of the indium-tin-oxide (ITO)/Y2O3/Ag and ITO/Y2O3/Cu RRAM devices. Between Ag and Cu, Cu can easily be oxidized due to its standard redox potential values. However, the conductive filament is easily formed using Ag TEs. After triggering the oxidation process, the formed Ag mobile metal ions can migrate faster inside Y2O3 active channel materials when compared to the formed Cu mobile metal ions. The fast migration inside the Y2O3 active channel materials successfully reduces the SET voltage and improves the number of programming-erasing cycles, i.e., endurance, which is one of the nonvolatile memory parameters. These results elucidate the importance of the electrochemical properties of TEs, providing a deeper understanding of how these factors influence the resistive switching characteristics of metal oxide-based atomic switches and conductive-metal-bridge-filament-based cells.
RESUMO
In the semiconductor manufacturing process, when conducting inductively coupled plasma-reactive ion etching in challenging environments, both wafers and the ceramic components comprising the chamber's interior can be influenced by plasma attack. When ceramic components are exposed to long-term plasma environments, the eroded components must be replaced. Furthermore, non-volatile reactants can form and settle on semiconductor chips, acting as contaminants and reducing semiconductor production yield. Therefore, for semiconductor processing equipment parts to be utilized, it is necessary that they exhibit minimized generation of contaminant particles and not deviate significantly from the composition of conventionally used Al2O3 and Y2O3; part must also last long in various physicochemical etching environment. Herein, we investigate the plasma etching behavior of Y2O3-Y4Al2O9 (YAM) composites with a variety of mixing ratios under different gas fraction conditions. The investigation revealed that the etching rates and changes in surface roughness for these materials were significantly less than those of Y2O3 materials subjected to both chemical and physical etching. Microstructure analysis was conducted to demonstrate the minimization of crater formation. Mechanical properties of the composite were also analyzed. The results show that the composite can be commercialized as next-generation ceramic component in semiconductor processing equipment applications.
RESUMO
The structural, surface morphological, optical absorption and emission features of Y2 O3 :Ce (0%-5%) were studied. The samples had a body-centred cubic crystal structure. The undoped sample had a crystallite size of 29.03 nm, and it varied after doping with Ce. The grain size of the samples varied from 23.00 to 50.78 nm. All the samples exhibited a strong absorption band at 206 nm due to F-centre absorption and absorption involving the delocalised bands. In addition, the doped samples exhibited a secondary band at ~250 nm due to 4f â 5d transitions of Ce3+ ions. The optical bandgap of the undoped sample was found to be ~5.37 eV, and it decreased to 5.20 eV with an increase in Ce concentration to 5%. The undoped sample under 350-nm excitation exhibited a broad photoluminescence (PL) emission band with the maxima at 406 nm and a secondary band at 463 nm. In contrast, multiple PL peaks were centred at ~397, 436, 466, 488 and 563 nm in all the doped samples. The average lifetime of the emission band at 406 nm was 1.05 ns and that of the emission band at ~466 nm was 1.63 ns. The material has potential for solid-state lighting applications.
Assuntos
Azocinas , Compostos Benzidrílicos , Iluminação , Substâncias LuminescentesRESUMO
Highly transparent Ho:Y2O3 ceramics for laser diode lighting were prepared using the vacuum sintering method with 0.3 at.% Nb2O5 as a sintering additive. The microstructures, transmittance, and luminescence properties of the Ho:Y2O3 ceramic samples were investigated in detail. The transmittance levels of all samples with various Ho3+ concentrations reached ~81.5% (2 mm thick) at 1100 nm. Under the excitation of 363 nm (ultraviolet) or 448 nm (blue) light, Ho:Y2O3 transparent ceramic samples showed that green emission peaked at 550 nm. The emission intensity was strongly affected by the concentration of Ho3+ ions, reaching its highest level in the sample doped with 1 at.% Ho3+. The CIE coordinates of the luminescence were in the green region (i.e., the CIE coordinates of the sample doped with 1 at.% Ho3+ were [0.27, 0.53] and [0.30, 0.69], under the excitation of 363 nm and 448 nm light, respectively). The possibility of its application as laser diode lighting was reported. Under the excitation of 450 nm blue laser, the sample doped with 0.5 at.% Ho3+ had the best performance: the saturated luminous flux, lumen efficiency, and the luminescence saturation power densities were 800 lm, 57.7 lm/W, and 17.6 W/mm2, respectively. Furthermore, the materials have high thermal conductivity and mechanical strength due to their host of rare-earth sesquioxide. Thus, Ho:Y2O3 transparent ceramics are expected to be a promising candidate for green-light-emitting devices for solid-state lighting, such as laser diode lighting.
RESUMO
Glycerol is a main by-product of biodiesel production, and its further processing is essential for the biorefinery. In this paper, a highly active and stable catalyst for the catalytic dehydration of glycerol to acetol is obtained by modifying a Cu-Zr (ZrO2 supported Cu) catalyst with Y2O3 using a co-precipitation method. It is found that the addition of Y2O3 effectively enhances the catalytic performance of Cu-Zr. Cu-Zr reaches the highest selectivity (82.4%) to acetol at 24 h. However, the selectivity decreases to 70.1% at 36 h. The conversion also decreases from 99.2 to 91.1%. Cu-Zr-Y exhibits very high activity and very good stability. During a 250 h reaction, no deactivation is observed, and the conversion and selectivity remains ~100% and ~85%, respectively. The catalysts are characterized by XRD, TEM, H2-TPR, and NH3-TPD. The results reveal that Y2O3 not only improves the dispersion of Cu and the acidity of the catalyst but also restrains the agglomeration of Cu particles and assists retaining the main structure of support under reaction conditions. The high dispersion, high acidity content, and stable structure contributes to the excellent catalytic performance of Cu-Zr-Y.
RESUMO
Lanthanide-doped core-shell nanomaterials have illustrated budding potential as luminescent materials, but their biological applications have still been very limited due to their aqueous solubility and biocompatibility. Here, we report a simple and cost-effective approach to construct a water-stable chitosan-functionalized lanthanoid-based core shell (Ca-Eu:Y2O3@SiO2) nanophosphor. The as-synthesized Ca-Eu:Y2O3@SiO2-chitosan (CEY@SiO2-CH) nanophosphor has been characterized for its structural, morphological, and optical properties, by employing different analytical tools. This sensing platform is suitable for dsDNA probing by tracing the "turn on" fluorescence signal generated by CEY@SiO2-CH nanophosphor with the addition of dsDNA. The ratio of fluorescence intensity enhancement is proportional to the concentration of dsDNA in the range 0.1-90 nM, with the limit of detection at â16.1 pM under optimal experimental conditions. The enhancement in fluorescence response of functionalized core-shell phosphor with dsDNA is due to the antenna effect. Additionally, response of probe has been studied for the real samples displaying percent recovery in between 101 and 105, maximum RSD% upto 5.23 (n = 3). This outcome can be applied to the selective sensing of dsDNA through optical response. These findings establish the CEY@SiO2-CH a simple, portable, and potential candidate as a sensor for rapid and analytical detection of dsDNA.
Assuntos
Técnicas Biossensoriais , Quitosana , Európio/química , Dióxido de Silício/química , Corantes , Água , DNARESUMO
Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol-gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics without requiring a high-voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated, and the results revealed that the resistance values gradually decreased with increasing set current compliance values. By regulating these values, the formation of pure Ag conductive filament could be restricted. The dominant oxygen ion diffusion and migration within Y2O3 leads to the formation of oxygen vacancies and Ag metal-mixed conductive filaments between the two electrodes. The filament composition changes from pure Ag metal to Ag metal mixed with oxygen vacancies, which is crucial for realizing multilevel cell (MLC) switching. Consequently, intermediate resistance values were obtained, which were suitable for MLC switching. The fabricated Y2O3 RRAM devices could function as a MLC with a capacity of two bits in one cell, utilizing three low-resistance states and one common high-resistance state. The potential of the Y2O3 RRAM devices for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM devices demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This indicates that the proposed RRAM can be utilized as a memory component in practical neuromorphic systems.
RESUMO
Herein, sol-gel-processed Y2O3-Al2O3 mixed oxide-based resistive random-access-memory (RRAM) devices with different proportions of the involved Y2O3 and Al2O3 precursors were fabricated on indium tin oxide/glass substrates. The corresponding structural, chemical, and electrical properties were investigated. The fabricated devices exhibited conventional bipolar RRAM characteristics without requiring a high-voltage forming process. With an increase in the percentage of Al2O3 precursor above 50 mol%, the crystallinity reduced, with the amorphous phase increasing owing to internal stress. Moreover, with increasing Al2O3 percentage, the lattice oxygen percentage increased and the oxygen vacancy percentage decreased. A 50% Y2O3-50% Al2O3 mixed oxide-based RRAM device exhibited the maximum high-resistance-state/low-resistance-state (HRS/LRS) ratio, as required for a large readout margin and array size. Additionally, this device demonstrated good endurance characteristics, maintaining stability for approximately 100 cycles with a high HRS/LRS ratio (>104). The HRS and LRS resistances were also retained up to 104 s without considerable degradation.
RESUMO
The successful application of glass-based materials in a wide range of scientific fields depends on the associated physical, optical, thermal, and mechanical properties. This article investigate the structural, Physical, thermal, optical, and mechanical properties of Dy2O3, Y2O3 co-activated telluro-borate glass developed using the melt-quenching method. The glassy quality and the elements component of the specimens were observed using XRD and EDX analyses. The addition of Y2O3 rise the glass density from 2.956 to 3.303 g/cm3 the refractive index from 2.5 to 2.7. These changes are due to the increase in polarizability and non-bridging oxygen (NBO). The photoluminescence (PL) spectra revealed a broad peak at 550 nm and additional weak emission peaks at 573 and 664 nm, respectively. While the observed broader peak can be linked to the convolution of Bi3+ ions transitions corresponding to the non-centrosymmetric site respectively, the weak emission bands are due to 4F9/2 â 6H13/2 and 4F9/2 â 6H11/2 Dy3+ transitions. Hence, the low symmetrical features of both Bi3+ and Dy3+ ions were confirmed. The increase in the Vickers hardness of the glass from 536.7 to 1366.9 indicates the influence of Y2O3 addition on the mechanical properties of the glasses. The findings help to improve our understanding of the behaviour of the glass composition and its prospective applications in disciplines such as photonic, and laser optics.
RESUMO
Luminescent materials used in flat panel displays, compact fluorescent lamps, and light-emitting diodes require high purity, uniform particle size, clean surfaces, spherical shape, and dense morphology to ensure long-term stability. Y2 O3 :Eu3+ is a widely studied red phosphor known for its characteristic photoluminescence (PL) emission at 613 nm with near-UV excitation at 392 nm. Many methods have been explored to synthesize Y2 O3 :Eu3+ nanoparticles with exceptional purity, consistent phases, and uniform particle sizes. The aim is to synthesize particles with pristine surfaces, spherical shape, and compact morphology. This study focuses on the low-temperature synthesis and PL investigation of Y2-x O3 :Eux 3+ nanophosphors using combustion with thioglycerol as fuel. The results are compared with Y2-x O3 :Eux 3+ red nanophosphors synthesized using wet chemical and nitrate combustion methods. The PL characteristics of the Y2-x O3 :Eux 3+ nanophosphors were analyzed using PL emission spectroscopy, X-ray diffraction, and scanning electron microscopy. These findings highlight the advantageous properties of the synthesized nanophosphors, such as their suitability for solid-state lighting applications in the lamp industry as highly efficient red phosphors. The combination of high purity, uniform particle size, clean surfaces, spherical shape, and dense morphology contributes to their potential for long-term stability and reliable performance in lighting devices.
Assuntos
Európio , Raios Ultravioleta , Európio/química , Temperatura , LuminescênciaRESUMO
This study demonstrates the successful synthesis of Ni/Y2O3 nanocomposite particles through the application of ultrasound-assisted precipitation using the ultrasonic spray pyrolysis technique. They were collected in a water suspension with polyvinylpyrrolidone (PVP) as the stabiliser. The presence of the Y2O3 core and Ni shell was confirmed with transmission electron microscopy (TEM) and with electron diffraction. The TEM observations revealed the formation of round particles with an average diameter of 466 nm, while the lattice parameter on the Ni particle's surface was measured to be 0.343 nm. The Ni/Y2O3 nanocomposite particle suspensions were lyophilized, to obtain a dried material that was suitable for embedding into a polylactic acid (PLA) matrix. The resulting PLA/Ni/Y2O3 composite material was extruded, and the injection was moulded successfully. Flexural testing of PLA/Ni/Y2O3 showed a slight average decrease (8.55%) in flexural strength and a small decrease from 3.7 to 3.3% strain at the break, when compared to the base PLA. These findings demonstrate the potential for utilising Ni/Y2O3 nanocomposite particles in injection moulding applications and warrant further exploration of their properties and new applications in various fields.