Effect of Sextant Fixating Angle of Spiral Clavicle Plate on Biomechanical Stability-A Preliminary Finite Element Study.

INTRODUCTION: A spiral clavicle plate has been accepted for its superior multidirectional compatibility in the treatment of midshaft clavicle fractures from a biomechanical perspective. However, the influence of the sextant angle (spiral level) definition on biomechanical performance has not been clarified. A conceptual finite element analysis was conducted to identify the advantages and drawbacks of spiral clavicle plates with various sextant angle definitions. METHODS: Conventional superior and three different conceptual spiral plates with sextant angle definitions ranging from 45 to 135 degrees were constructed to restore an OTA 15-B1.3 midshaft clavicle fracture model. Three major loading scenarios (cantilever downward bending, axial compression, and axial torsion) were simulated to evaluate the reconstructed structural stiffness and the stress on the clavicle plate and bone screws. RESULTS: The spiral clavicle plate demonstrated greater capability in resisting cantilever downward bending with an increase in sextant angle and showed comparable structural stiffness and implant stress compared to the superior clavicle plate. However, weakened resistance to axial compression load was noted for the spiral clavicle plate, with lowered stiffness and increased stress on the clavicle plate and screws as the spiral level increased. CONCLUSION: The spiral clavicle plate has been reported to offer multidirectional compatibility for the treatment of midshaft clavicle fractures, as well as geometric advantages in anatomical matching and reduced skin prominence after surgery. The current study supports that remarkable cantilever bending strength can be achieved with this plate. However, users must consider the potential drawback of lowered axial compression resistance in safety considerations.

Sex estimation using post-mortem computed tomographic images of the clavicle in a Malaysian population.

Forensic practitioners need contemporary anthropological data for the identification of human remains. The clavicle possesses a high degree of variability in its anatomical, biomechanical, and morphological features that are sex-dependent albeit population specific. The aim of this study was to develop sex estimation models for Malaysian individuals using post-mortem computed tomographic images of the clavicle. Sample comprised scans of 2.0 mm resolution of 405 individuals (209 male; 196 female) aged between 19 to 88 years. These scans were reconstructed and visualized using Infinitt. Six clavicular measurements (i.e. maximum length, C1; midshaft circumference, C2; midshaft maximum diameter, C3; midshaft minimum diameter, C4; maximum breadth of the sternal end, C5; and maximum breadth of the acromial articular surface, C6) were obtained from these images. Data were analyzed using descriptive statistics and discriminant function analysis. Measurements taken from the images were highly precise (ICC = 0.770-0.999). There is a significant difference between all parameters and sex (p < 0.001), however none for age and ethnic group. A multivariate sex estimation model was developed: Sex = (C1*0.86) + (C2*0.236) + (C3*-0.145) + (C5*- 0.074) - 17.618; with an accuracy rate of 89.1 % and sex bias of -3.2 %. Lower accuracy rates were obtained for single variable models (61.5-83.2 %). The resultant sex discriminant models can be used for estimating sex based on the clavicle in our local forensic practice.

Forensic age estimation of adolescents using computed tomography of the clavicles.

In forensic age estimation, CT imaging of the clavicles is used to determine an age over completed 21 years. If ossification of the medial clavicular epiphysis is complete, young men are assumed to be over 21 years of age. The aim of this study is to check the statistical parameters (specificity, predictive probability) for the characteristic "completed ossification of the medial clavicles". 285 male patients who, for various reasons, received a chest CT at the Medical Center of the University of Freiburg between 1st December 2019 and 6th December 2022 were screened for the study, of whom 203 patients were included in the study. The stage of clavicular ossification was classified as stage 1 - 5 according to Schmeling. While 70 out of 71 patients under 21 years of age were correctly estimated to be under 21 years of age, there was one patient whose ossification on one side was classified as stage 4 and who would therefore have been estimated to be over 21 years of age. If only subjects whose ossification stage was the same on both sides are included, the specificity of the test method is 100% and the positive predictive probability is 100%. If patients for whom only one side is stage 4 are also included, the specificity is 98.6%. Thus, only the complete and symmetrical ossification of both clavicles (stage 4 according to the Schmeling classification) in a standardised thin-layer CT can be classified as a reliable indicator of an age over 21 years in young men. In the case of asymmetric ossification of the medial clavicles (stage 4 is not reached on one side), false positive evaluations and the incorrect assumption of an age over 21 years can occur.

Subcostal wire migration from the left clavicle internal fixation: A case report.

BACKGROUND: Kirschner wire is a widely used implant in orthopedics, with migration being a typical problem following internal fixation. Subcostal wire migration might result in catastrophic problems such as penetration of the heart, lungs, trachea, big blood vessels, or abdominal cavity. Every orthopedic surgeon must be vigilant and mindful of the potential hazards of wire migration. CASE REPORT: a 45-year-old Indonesian male was referred from another hospital. 1 year prior, the patient underwent internal fixation of the left clavicle. 2 weeks before admission, the patient complained of stabbing pain in the left shoulder area. An X-ray examination revealed a broken end wire in the left infraclavicular area. Immediate wire-extraction surgery was planned. An X-ray and CT scan showed that the wire had migrated into the left lateral side of the 9th subcostal space and was heading inferiorly. The Thoracic and Cardiovascular Surgery Department carried out the wire evacuation. The wire was successfully removed without any concern. DISCUSSION: Previous studies have suggested that wire migration can occur due to muscular activity, respiratory motion, gravity, and upper-extremity movement. Wire migration is a condition that can occur following shoulder fixation, especially in comminuted fractures that typically use K-wires to stabilize the fragments. Upon the detection of wire migration, prompt evacuation should be conducted to mitigate the severity. CONCLUSION: In cases of wire migration, orthopedic surgeons should pay special attention. Actions that can be taken to prevent wire migration are to: bend the wire, use a threaded wire, and remove it quickly after callus formation.

Satisfactory results in five patients with septic clavicle nonunion using the modified Masquelet technique and structural iliac crest autograft.

Background: Indications for clavicle fracture fixation have increased dramatically over the last 20 years. Chronic surgical site infection is a particularly severe complication arising from this procedure and can induce nonunion and clinical disability. In such cases, the modified Masquelet technique using an iliac crest autograft (cancellous or tricortical) enables treatment of any bone infection as well as reconstruction of the segmental defect. The aim of this study was to analyze the clinical and radiological results of this procedure at mid-term follow-up. Methods: In this monocentric retrospective study, patients suffering from a septic clavicle nonunion were treated with a modified Masquelet technique and reviewed at a minimum follow-up point of two years. They were clinically assessed using active range of motion, pain score (visual analog scale 0 to 10), Constant score, American Shoulder and Elbow Surgeons score, and subjective shoulder value score. Bone healing was measured using standard X-rays and CT scans. Results: Five patients were included (mean age 49 years; range 30 to 62). C. acnes was involved in 80% (n = 4) of these cases. Following the first stage of treatment, the mean bone defect was 3.4 cm (range 2.6 to 6.4 cm). The second stage, performed at a minimum of six weeks (mean 7 ± 1 weeks), used an iliac crest bone autograft in all cases. At a mean follow-up of 5 ± 3 years, the mean pain score was 0.3/10 points (0 to 1), the mean Constant score was 86 points (78 to 96), the mean American Shoulder and Elbow Surgeons score was 98 ± 2%, and the subjective shoulder value score 91 ± 11%, with two "forgotten shoulders" out of five. On CT scan analysis, bone healing was achieved in 100% of cases. One plate (20%) was removed one year following the procedure due to the patient's discomfort; pain and discomfort at the iliac crest site were reported in 5/5 (100%) patients. Conclusion: The modified Masquelet technique using an iliac crest autograft is a reliable and effective technique for treating septic nonunion of the clavicle. It both treats the bony defect and eradicates infection when conducted in association with débridement and antibiotics. In the five cases reported here, this approach had satisfactory results, both subjectively and objectively, with a very low reoperation rate despite persistent pain from iliac bone harvesting.

The Results of Hook Plate Fixation in Acute Acromioclavicular Joint Dislocation and Distal Clavicle Fractures.

Background: Acromioclavicular joint (ACJ) dislocation and distal clavicle fractures are common shoulder injuries. Different methods of fixation are used to treat such injuries, each has its advantages and disadvantages. In this study, we tested fixation using the hook plate. We think that it is technically simple, reliable and more effective in certain surgical situations. However, it is not gaining adequate popularity due to the potential complications of the plate placement including subacromial osteolysis, impingement, rotator cuff injury and others. A second surgery for plate removal is classically indicated to cope with such complications. Objective: The aim of this study included evaluating the clinical and radiological healing after hook plate fixation in ACJ dislocation and distal clavicle fractures and assessing the incidence and clinical significance of subacromial osteolysis. Methods: It is a prospective observational study with a total of 96 cases including 64 ACJ dislocations and 32 distal clavicle fractures. Constant-Murley score was used for clinical evaluation. The patients were evaluated regularly with a minimum follow up of 12 months after plate removal. Results: At the end of the study we found that the results of the hook plate fixation for both groups were good clinically and radiologically. The clinical result score was found to be initially higher among the patients of the ACJ dislocation mainly due to the earlier plate removal in these patients. However, the final score was found to be comparable in both groups. The incidence of the subacromial osteolysis was found to be higher among the patients with clavicle fractures as the plate was retained for a longer time. However we found that subacromial osteolysis did not imply any increased rate of symptoms over the patients who did not show this complication on the X-ray. Conclusion: Based on these observations, we recommend the hook plate fixation to be added to the armamentarium of the orthopaedic surgeon treating such injuries as it is simple to implement, durable and capable of dealing with difficult situations. The main disadvantage of this method is the need for a second surgery for plate removal.

Bone Density Changes at the Origin of the Deltoid Muscle following Reverse Shoulder Arthroplasty.

Background: Reverse total shoulder arthroplasty (RSA) significantly impacts deltoid length, tension, and structure. Studies have extensively investigated various modifications in deltoid characteristics, such as perfusion, elasticity, caliber, histological changes, and strength post-RSA. However, to date, there is a notable absence of research evaluating changes in bone mineral density (BMD) at the deltoid muscle origin after the RSA procedure. Methods: A retrospective analysis of a consecutive series of RSAs performed between May 2011 and May 2022 was conducted. Inclusion criteria comprised primary RSAs with both preoperative and last follow-up shoulder CT scans and a minimum follow-up of 12 months. Trabecular attenuation measured in Hounsfield units (HU) was calculated using a rapid region-of-interest (ROI) method. BMD analysis involved segmenting three ROIs in both pre- and postoperative CT scans of each patient: the acromion, clavicle, and spine of the scapula. Results: A total of 44 RSAs in 43 patients, comprising 29 women and 14 men, were included in this study. The mean follow-up duration was 49 ± 22.64 months. Significant differences were observed between preoperative and postoperative HU values in all analyzed regions. Specifically, BMD increased in the acromion and spine, while it decreased in the clavicle (p-values 0.0019, <0.0001, and 0.0088, respectively). Conclusions: The modifications in shoulder biomechanics and, consequently, deltoid tension post-implantation result in discernible variations in bone quality within the analyzed regions. This study underscores the importance of thorough preoperative patient planning. By utilizing CT images routinely obtained before reverse shoulder replacement surgery, patients at high risk for fractures of the acromion, clavicle, and scapular spine can be identified.

Clavipectoral fascial plane block for clavicle fracture surgery: a case report.

BACKGROUND: Regional anaesthesia can be an attractive alternative anaesthetic approach in clavicle surgery, but it requires the peripheral block of multiple cervical and brachial nerves that transmit nociceptive information. Deep cervical plexus blocks, as paravertebral nerve block, can lead to severe side effects, such as unilateral diaphragmatic paralysis. CASE REPORT: A 66-year-old male patient, American Society of Anesthesiologists physical status III, was scheduled for open reduction and internal fixation of the right clavicle with plates and screws after a high-energy trauma. Pre-anaesthetic evaluation revealed right hemopneumothorax and bilateral rib fractures. We decided to perform regional anaesthesia (superficial cervical plexus block and clavipectoral fascial plane block), combined with dexmedetomidine perfusion to avoid invasive mechanical ventilation and prevent additional pulmonary complications. The surgical procedure was successfully completed without any further anaesthesia requirements. The patient remained comfortable during the postoperative period. CONCLUSION: Regional anaesthesia for clavicle surgeries has the advantage of promoting non-opioid free anaesthesia. Effective pain control enhances patient satisfaction and reduces the length of stay in hospital. In our case report, a combined superficial cervical plexus block and clavipectoral fascial plane block was a safe and effective regional anaesthetic approach.

Study of surgical performance during clavicle plate placements using 2 learning methods: naive practice versus deliberate practice.

BACKGROUND: Companionship and simple experience or naive practice (NP) rarely lead to expert level surgery, in contrast to deliberate practice (DP) where an expert analyzes the learner's errors and sets goals to improve performance. The main hypothesis was that using DP for learning would result in faster and/or greater progress than using NP. OBJECTIVES: The objective of this work was to compare the evolution of the learning curve for clavicle locking plate placement on a sawbone model of a clavicle fracture, by surgical trainees learning via two different methods; NP and DP. PATIENTS AND METHODS: Ten surgical residents, divided into 2 groups of 5, each placed 6 plates. The 6 trials were filmed. The NP group saw an expert video before each placement. The DP group saw this video once and then received personalized advice from the expert for improvement, by analyzing their own video after each subsequent trial. Objective performance (OP) was measured by a standardized evaluation grid (OSATS, with a score ranging from 10 to 50 points per trial), self-evaluation of performance by a numerical scale (from 0 to 10) and stress by an analgesia-nociception index (ANI, calculated by heart rate recording, from 0 to 100). RESULTS: The mean OP at the last trial of clavicle plate placement was 41.8 (NP group) and 48.2 (DP group), with a mean progression from the first to last trials of 0.8 in the NP group, and 5.1 in the DP group. The mean progression in self-evaluation between the first and last trials was 3.4 (NP group) and 4.6 (DP group). The mean progression of the ANI between the first and last trials was -4.5 (NP group) and +5 (DP group). DISCUSSION: The results of learning a clavicle plate osteosynthesis technique measured by OSATS were better with deliberate practice than with naive practice. The progression in self-evaluated performance was better with deliberate practice, but with a higher stress level. CONCLUSION: Deliberate practice is a technique for learning the surgical procedure which complements companionship and experience. It shortens the learning curve and improves the level of performance of surgical trainees. LEVEL OF EVIDENCE: IV; non-interventional research.

Posterior sternoclavicular joint dislocation in a young male: a case report.

The traumatic dislocation of the posterior sternoclavicular joint is a serious injury with possibly severe complications and therefore has to be managed with the greatest caution. We report the case of a young male with a posterior dislocation of the medial clavicle with compression of the brachiocephalic artery as well as the esophagus. Open reduction and placement of a wire cerclage were performed with a good postoperative outcome.

Vascularized Reconstruction of Recalcitrant Clavicular Nonunion with the Medial Femoral Condyle Free Flap: A Systematic Review of the Literature.

Recalcitrant clavicular nonunion is an uncommon but challenging problem. Vascularized bone reconstruction is not first-line therapy due to complexity and donor morbidity, though it has utility in select cases. A systematic review of Embase and Medline databases was undertaken for cases of medial femoral condyle reconstruction for clavicle nonunion. Ten studies met inclusion, encompassing 26 patients. Mean age was 38.9 years. Ten patients were male and 16 female. Mean time of nonunion was 37.79 months prior to intervention; mean time to union following medial femoral condyle flap was 7.60 months. Two patients did not achieve union. Of the 11 patients who previously had at least one failed fixation with bone graft, considered the current "gold standard", 9 patients (81.81%) went on to achieve union, while 2 patients (18.19%) did not. There were six reported complications in five patients. Medial femoral condyle flap is a valuable option in recalcitrant clavicle nonunion.

SHORTENING OF CLAVICLE FRACTURES: PHYSICAL VERSUS IMAGE EXAMINATIONS.

Objective: Determine the reliability of three different methods of evaluating bone shortening in displaced midshaft clavicle fractures (DCMF). Method: A cross-sectional analytical study evaluated bone shortening by metric tape (MT), radiography (X-ray), and computed tomography (CT). Twenty-six men had been evaluated and used clavícula not broken as control. The collection of data was of the blind type for three specialists. Differences and reliability were analyzed with the Friedman and Kappa tests and validated with the T-test (CI: 95%; significance index p<0.05; Software "R" version 3.2.2). Results: The MT measurements (control) showed abnormal distribution and significant statistical difference concerning the imaging tests (p=0.000008). There was a similarity between X-ray and CT and Kappa agreement of 0.65. The fractured clavicles presented similar measurements between the three methods (p=0.059), and the T-tests proved that the similarity was caused by chance or possible measurement errors. Conclusion: Measurement by metric tape showed a tendency to overestimate bone shortening. The CT showed more reliable results for the diagnosis; however, the X-ray was sufficient for decision-making by surgeons, and therefore, it is not possible to rule out the importance of this resource for DCMF. Level of Evidence IV; Case-Control Study.

Objetivo: Determinar a confiabilidade de três diferentes métodos de avaliação do encurtamento ósseo em fraturas deslocadas do eixo médio da clavícula (FDEMC). Método: Estudo analítico transversal que avaliou o encurtamento ósseo por fita métrica (FM), radiografia (X-Ray) e tomografia computadorizada (TC). Foram avaliados 26 homens utilizando a clavícula não fraturada como controle. A coleta de dados foi do tipo cega por três especialistas. As diferenças e a confiabilidade foram analisadas com os testes de Friedman e Kappa e validados com o teste T (IC:95%; índice de significância p<0,05; Software "R" versão 3.2.2). Resultados: As medidas de FM (controle), apresentaram distribuição anormal e diferença estatísfica significativa em relação aos exames de imagem (p=0,000008). Houve semelhança entre radiografia e TC, concordância Kappa 0,65. As clavículas fraturadas apresentaram medidas semelhantes entre os três métodos (p=0,059) e os testes-T comprovaram que a semelhança foi provocada casualmente ou possíveis erros de medição. Conclusão: A medição por fita métrica apresentou tendência em superestimação do encurtamento ósseo. A TC apresentou resultados mais confiáveis para o diagnóstico, contudo, a radiografia foi suficiente para tomada de decisão dos cirurgiões e por isso, não é possível descartar a importância deste recurso para FDEMC. Nível de Evidência IV; Estudo Caso Controle.

No code machine learning: validating the approach on use-case for classifying clavicle fractures.

PURPOSE: We created an infrastructure for no code machine learning (NML) platform for non-programming physicians to create NML model. We tested the platform by creating an NML model for classifying radiographs for the presence and absence of clavicle fractures. METHODS: Our IRB-approved retrospective study included 4135 clavicle radiographs from 2039 patients (mean age 52 ± 20 years, F:M 1022:1017) from 13 hospitals. Each patient had two-view clavicle radiographs with axial and anterior-posterior projections. The positive radiographs had either displaced or non-displaced clavicle fractures. We configured the NML platform to automatically retrieve the eligible exams using the series' unique identification from the hospital virtual network archive via web access to DICOM Objects. The platform trained a model until the validation loss plateaus. Once the testing was complete, the platform provided the receiver operating characteristics curve and confusion matrix for estimating sensitivity, specificity, and accuracy. RESULTS: The NML platform successfully retrieved 3917 radiographs (3917/4135, 94.7 %) and parsed them for creating a ML classifier with 2151 radiographs in the training, 100 radiographs for validation, and 1666 radiographs in testing datasets (772 radiographs with clavicle fracture, 894 without clavicle fracture). The network identified clavicle fracture with 90 % sensitivity, 87 % specificity, and 88 % accuracy with AUC of 0.95 (confidence interval 0.94-0.96). CONCLUSION: A NML platform can help physicians create and test machine learning models from multicenter imaging datasets such as the one in our study for classifying radiographs based on the presence of clavicle fracture.

Efficacy of intramedullary bridge fixation for midshaft clavicle fractures: a retrospective analysis of a novel technique.

BACKGROUND: The aim of this study was to explore the efficacy of a novel intramedullary fixation technique using the ortho-bridge system (OBS) for midshaft clavicle fractures. METHODS: A total of 63 patients were included in this study: 35 underwent plate internal fixation (LP group) and 28 underwent OBS intramedullary fixation (OBS group). Surgical time, intraoperative blood loss, incision length, fracture healing time, removal of the internal fixation agent, visual analog scale (VAS) score for shoulder pain, Constant-Murley shoulder score and complication occurrence were compared between the two groups. RESULTS: Preoperative general data, such as sex, age and fracture type, were not significantly different between the two groups (P > 0.05). However, the OBS group exhibited better outcomes than the LP group exhibited in terms of surgical time, intraoperative blood loss and total incision length (P < 0.05). Additionally, the OBS group exhibited a significantly shorter fracture healing time and internal-fixation removal time than the LP group exhibited (P < 0.05). The VAS scores on postoperative day 1, week 1, month 1 and month 3 were lower in the OBS group than in the LP group (P < 0.05). Furthermore, the Constant-Murley shoulder scores at 1, 3, and 6 months postoperatively were higher in the OBS group than in the LP group (P < 0.05), with no significant difference at 1 year after surgery (P > 0.05). None of the patients in the OBS group experienced scarring of the surgical incision, and 6 patients in the LP group experienced scarring of the surgical incision. Finally, the complication incidence in the OBS group was lower than that in the LP group. CONCLUSION: For midshaft clavicle fractures, OBS intramedullary fixation is better than locking-plate internal fixation because it led to less trauma, a faster recovery, better efficacy, and better esthetic outcomes and comfort. Therefore, this technique may have potential as a novel treatment for midshaft clavicle fractures. LEVEL OF EVIDENCE: III, retrospective observational study.

Using a Nice knot to simplify and strengthen closed reduction in displaced distal clavicle fracture: a technical note.

A displaced distal clavicle fracture often necessitates surgical intervention, with various open and closed reduction options. Open reduction is easier but raises blood supply concerns, while closed reduction can involve complex deforming forces with differing displacement vectors. Herein, we demonstrate how a Nice knot with its sliding and self-locking qualities can be used to make closed reduction easier and the alignment more secure. A case report illustrates this Nice knot application in a 61-year-old male with a distal clavicle fracture. The Nice knot's ability to be loosened and retightened ensured more precise alignment in this case. The Nice knot technique is a versatile option for easier and more secure distal clavicle fracture management.

Can we screen opportunistically for low bone mineral density using CT scans of the shoulder and artificial intelligence?

OBJECTIVE: To evaluate whether the CT attenuation of bones seen on shoulder CT scans could be used to predict low bone mineral density (BMD) (osteopenia/osteoporosis), and to compare the performance of two machine learning models to predict low BMD. METHODS: In this study, we evaluated 194 patients aged 50 years or greater (69.2 ± 9.1 years; 170 females) who underwent unenhanced shoulder CT scans and dual-energy X-ray absorptiometry within 1 year of each other between January 1, 2010, and December 31, 2021. The CT attenuation of the humerus, glenoid, coracoid, acromion, clavicle, first, second, and third ribs was obtained using 3D-Slicer. Support vector machines (SVMs) and k-nearest neighbours (kNN) were used to predict low BMD. DeLong test was used to compare the areas under the curve (AUCs). RESULTS: A CT attenuation of 195.4 Hounsfield Units of the clavicle had a sensitivity of 0.577, specificity of 0.781, and AUC of 0.701 to predict low BMD. In the test dataset, the SVM had sensitivity of 0.686, specificity of 1.00, and AUC of 0.857, while the kNN model had sensitivity of 0.966, specificity of 0.200, and AUC of 0.583. The SVM was superior to the CT attenuation of the clavicle (P = .003) but not better than the kNN model (P = .098). CONCLUSION: The CT attenuation of the clavicle was best for predicting low BMD; however, a multivariable SVM was superior for predicting low BMD. ADVANCES IN KNOWLEDGE: SVM utilizing the CT attenuations at many sites was best for predicting low BMD.

Ultrasound-Guided Clavipectoral Fascial Plane Block as a Stand-Alone Anesthetic Technique for Clavicle Fracture Management: A Case Report.

The clavipectoral fascial plane block (CFPB) that has been utilized for clavicle fracture surgeries and pain management is an emerging anesthetic technique. It has been previously used for postoperative pain management, but it can also be used as a stand-alone anesthetic technique for clavicle fracture management. Here we describe a case of a 20-year-old male who underwent open reduction and internal fixation (ORIF) with plating for a mid-shaft clavicular fracture under a CFPB as a sole anesthetic.

Comparative clinical outcomes and radiological images of clavicle hook plate versus Scorpion Plate® for unstable distal clavicle fractures.

BACKGROUND: Although various surgical methods are available for unstable distal clavicle fractures, consensus remains lacking on the optimal technique. Therefore, the present retrospective study aimed to compare the clavicle hook plate and Scorpion Plate® in terms of clinical outcomes and radiological findings for unstable distal clavicle fractures. METHODS: Fifty-seven patients with unstable distal clavicle fractures who underwent treatment using a clavicle hook plate (Group H; 28 patients) or Scorpion Plate® (Group S; 29 patients) were included in the present study. No patients received additional augmentation and all were followed-up for >1 year (mean follow-up, 28 months). Clinical outcomes were operation time, bleeding volume, complications, range of motion (ROM) at 6 months after surgery and final follow-up, and clinical scores (Constant-Murley score and University of California, Los Angeles (UCLA) shoulder score). Radiological outcomes assessed were coracoclavicular distance (CCD), difference in CCD between affected and non-affected sides (ΔCCD), and acromioclavicular subluxation ratio (%ACS) from plain X-rays. The χ2 test and Mann-Whitney U test were used to compare each outcome. RESULTS: Complications were seen in 3 shoulders (10.7%) in Group H. ROM was significantly worse in Group H at 6 months postoperatively, but no significant differences between groups were evident at final follow-up. Moreover, no significant differences in clinical outcomes were seen between groups. In terms of radiological results, Group H showed greater improvement in CCD and ΔCCD than Group S. Further, %ACS was significantly worse in Group S. CONCLUSIONS: The clavicle hook plate allows reconstruction of a more anatomical position than the Scorpion Plate®, but carries a greater risk of complications. Conversely, the Scorpion Plate® has a low risk of complications, but acromioclavicular subluxation remains. However, no significant differences in ROM or clinical outcomes were apparent at final follow-up.

Early to Mid-term Results of Coracoclavicular Ligament Reconstruction Using the Infinity-Lock Button System in the Management of Traumatic Acromioclavicular Joint Dislocations and Lateral End of Clavicle Fractures.

Background The management of distal clavicle injuries with disruption of the coracoclavicular ligaments (CCLs) is challenging. The aim of this study was to assess the functional results of reconstructing the CCLs with the Infinity-Lock Button System using validated outcome measures, patient satisfaction scores, return to pre-injury activity, and complications. Methods A total of 28 cases of CCL disruption were assessed over a seven-year period, which included 14 lateral end-of-clavicle fractures and 14 acromioclavicular joint (ACJ) dislocations. All patients underwent stabilisation of the CCLs using the Infinity-Lock Button System. Patients were assessed preoperatively and postoperatively using validated outcome measures such as visual analogue scale (VAS), Oxford Shoulder Score (OSS), Quick Disabilities of Arm, Shoulder & Hand (Q-DASH) scores, return to pre-injury level of activities, patient satisfaction scores, and complications were reviewed. Results The mean age of patients was 36.7 years (18-74 years). The mean follow-up was 38.6 months (8-68 months). The mean time to surgery was 75.8 days (3-619 days). There was a statistically significant improvement in postoperative VAS, OSS, and Q-DASH scores compared to the preoperative (p-value <0.001). Out of the 28 participants, 23 (82.1%) returned to pre-injury level of activities, 25 (89.7%) reported 'good' or 'excellent' outcomes following the intervention, and none of the patients reported functional instability postoperatively. None of the patients required revision surgery or implant removal. Conclusion CCL reconstruction is vital in the management of clavicular injuries. This study demonstrates the safe use of the Infinity-Lock Button System in these injuries with statistically significant improvement in early patient-reported outcome measures, return to pre-injury level of activities, and subjective patient satisfaction.