Precise control of photogenerated carrier behavior of zinc oxide through band reconstruction to enhance photocatalytic treatment of dye wastewater.

In the field of photocatalytic treatment of dye wastewater, zinc oxide (ZnO) is a typical semiconductor photocatalyst, but it has some disadvantages such as wide band gap, low carrier yield and easy recombination. In this study, Cr-ZnO/N-CQDs catalyst was synthesised using the strategy of p-type doping and construction of Z-scheme heterojunction. The results showed that the removal rate of Cr-ZnO/N-CQDs for MB dye was 97.42 %, which was 70.56 % higher than that of ZnO, and was still 92.16 % after 5 cycles, and the TOC removal rate of methylene blue wastewater was 88.60 %. The reason for the enhanced photocatalytic activity of Cr-ZnO/N-CQDs is that the π* electron (e-) in the N-CQDs interact with the 3d orbitals of Cr-ZnO, so that e- is more easily transferred from the valence band of Cr-ZnO to the conduction band of N-CQDs. The band gap of p-type Cr-ZnO is narrowed, which makes its photogenerated carrier yield increase, hole concentration raise, and the adsorption capacity of H2O molecules reduce by 1.04 eV. The density functional theory calculation shows that the maximum Gibbs free energy of Cr-ZnO for the production of hydroxyl radical is 0.05 eV lower than that of ZnO. This study lays theoretical and practical foundation for the photocatalytic treatment of dye wastewater with ZnO.

Photothermal degradation of triphenylmethane dye wastewater by Fe3O4@C-laccase.

The degradation of synthetic dye wastewater is important for green chemistry and cost-effectiveness. In this study, we developed Fe3O4@C-laccase (laccase immobilized on Fe3O4@C nanoparticles) for photothermal degradation of high concentration of triphenylmethane dye wastewater. The Fe3O4@C-laccase possessed superior pH and thermal stabilities, as well as excellent tolerance to organic solvents, inhibitors, and metal ions. Laccase activity assays revealed that the activity recovery was approximately 118.2 %. Furthermore, the Fe3O4@C-laccase presented rapid and sustainable photothermal degradation capabilities to triphenylmethane dye wastewater. The initial removal efficiencies of 400 mg/L malachite green (MG), 400 mg/L brilliant green (BG), 100 mg/L crystal violet (CV), and 600 mg/L mixed dye (MG:BG:CV = 1:1:1) wastewater were approximately 99.8 %, 99.9 %, 96.4 % and 99.2 % by 60 min treatment, respectively. After undergoing 10 batches of reuse, the photothermal degradation efficiencies of the triphenylmethane dye wastewater remained consistently high, at about 99.3 %, 97.4 %, 94.0 %, and 95.1 %, respectively. The excellent photothermal degradation properties indicate that the Fe3O4@C-laccase holds promise for addressing high concentration of textile wastewater in various applications.

Application of Anionic Hydrogels from Date Palm Waste for Dye Adsorption in Wastewater Treatment.

This work aimed to develop an anionic cellulose nanofiber (CNF) bio-adsorbent from date palm tree waste and to investigate its removal efficiency compared to cationic methylene blue dye from contaminated water. Date palm pulp was first prepared from date palm leaves through acid hydrolysis using H2SO4, followed by hydrolysis in a basic medium using KOH, in which the process completely removed the components of hemicellulose, lignin, and silica. To obtain anionic CNF, the resulting pulp was further treated with H2SO4, followed by centrifugation. Biogel formation of the CNF suspension was promoted by sonication, where its removal efficiency of methylene blue dye was studied as a function of dye concentration, temperature, contact time, and pH value. In this work, we investigated two isotherms, i.e., Langmuir and Freundlich. The Langmuir model's consistency with the experimental data suggests that the adsorption of methylene blue dye onto CNF is monolayer and surface-limited. The reported maximum removal efficiency of 5 mg/g at 60 °C indicates the optimal temperature for adsorption in this specific case. Additionally, a pseudo-second-order model and Elovich model were also utilized to obtain a better understanding of the adsorption mechanism, in which we found not just physical adsorption but also an indication of a chemical reaction occurring between methylene blue dye and CNF. According to the results, that pseudo-second-order model's consistency with the experimental data suggests that the adsorption of methylene blue (MB) onto CNF is rate-limiting step involving chemisorption between the two. The study reveals that CNF adsorbents derived from renewable natural waste sources such as date palm leaves can be effective in removing cationic contaminants such as methylene blue dye.

Insights into the azo dye decolourisation and denitrogenation in micro-electrolysis enhanced counter-diffusion biofilm system.

In this study, electron transport pathways were activated and diversified by coupling counter-diffusion biofilms with micro-electrolysis for Alizarin yellow R (AYR) denitrogenation. Due to the binding of AYR to two residues of EC 4.1.3.36 with higher binding energy, the expression of EC 4.1.3.36 was down-regulated, causing the EC 3.1.2.28 and EC 2.5.1.74 for menaquinone synthesis (redox mediator) undetectable in Membrane aerated biofilm reactors (MABR). Spontaneous electron generation in the micro electrolysis-coupled MABR (ME-MABR) significantly activated two enzymes. Activated menaquinone up-regulated decolourisation related genes expression in ME-MABR, including azoR (2.12 log2), NQO1 (2.97 log2), wrbA (0.45 log2), and ndh (0.47 log2). The diversified electron flow pathways also promoted the nitrogen metabolism coding genes up-regulation, accelerating further inorganic nitrogen denitrogenation after AYR mineralisation. Compared to MABR, the decolourisation, mineralisation, and denitrogenation in ME-MABR increased by 25.80 %, 16.53 %, and 13.32 %, respectively. This study provides new insights into micro-electrolysis enhanced removal of AYR.

Efficient removal of direct dyes by SA-Er biopolymer gel spheres: Equilibrium isotherms, kinetics and regeneration performance study.

Biomass-based adsorbent materials are characterized by their low cost, environmental friendliness, and ease of design and operation. In this study, biomass-based hydrogel microspheres erbium alginate (SA/Er) with high stability and adsorption properties were prepared by a one-step synthesis method. The prepared materials were characterized and analyzed by SEM-EDS, XRD, TGA, FT-IR, UV-Vis, BET-BJH and XPS, and the adsorption performance of SA/Er was investigated for high concentrations of azo dyes in water. The results showed that the adsorption performance of SA/Er on the azo dyes of direct violet N (DV 1) and direct dark green NB (DG 6) with concentrations of 850 mg/L and 1100 mg/L under the optimal conditions was very high, and the adsorption amount could be up to 692 mg/g and 864 mg/g, respectively. The adsorption process was in accordance with the quasi-secondary kinetic model, which was accomplished by physical and chemical adsorption; the Langmuir isothermal model was able to better respond to the adsorption equilibrium, and the adsorption was dominated by the adsorption of surface monolayers; after seven desorption cycles, the removal of both azo dyes by the adsorbent material could reach >79.7 %. Combined with the results of FT-IR, UV-vis and XPS analysis before and after the adsorption, it was revealed that the adsorption of SA/Er with the dye molecules mainly consisted of hydrogen bonding, electrostatic adsorption and surface complexation, which resulted in the significant adsorption effect on the two azo dyes, and the above results can provide a reference for the treatment of dye wastewater.

Hydrothermal chemical modification of red mud for efficient adsorption of methylene blue.

Red mud (RM) is the industrial solid waste produced after alumina extraction from bauxite, and most RM is directly discharged to the landfill yards without any treatment. In this study, modified red mud (MRM) was synthesized by a hydrothermal chemical modification method as an efficient adsorbent for methylene blue (MB) removal. The prepared MRM was characterized by X-ray fluorescence spectroscopy, X-ray diffraction, scanning electron microscope, transmission electron microscope, and Fourier transform infrared spectrometer. The effects of reaction time, initial MB concentrations, MRM dosage, temperature, and system pH were investigated in the MB batch adsorption experiments. The results showed that the modification method increased the specific surface area of RM material from 16.72 to 414.47 m2/g. The maximum adsorption capacity of MRM for MB was 280.18 mg/g under the conditions of initial MB concentration of 1000 mg/L, reaction time of 300 min, temperature of 25 ℃, and natural pH of 6.06. Meanwhile, the adsorption kinetics and equilibrium isotherms were demonstrated to fit well with the pseudo-second-order kinetic model and Temkin isotherm, respectively. This study provides a new method for the valorization of RM and demonstrates that MRM can be used as a low cost and environmentally friendly potential adsorbent for the removal of MB from wastewater.

A Comparative Study on Characteristics and Antibacterial Capacity of Cotton Fabrics Dyed with Reactive Dye and Diospyros Mollis Extract.

This article focuses on comparing the characteristics of cotton fabric dyed with Diospyros mollis extract (DME) solution and that of cotton fabric dyed with the reactive dye. The parameters of the cotton fabric after dyeing with both types of dyes were assessed, including color strength (K/S), structural morphology, infrared spectrum, antibacterial properties, UV resistance, color fastness to washing, rubbing, light, moisture absorption, breathability, and wastewater indices. The obtained results show that the K/S value of cotton fabric dyed with DME solution is slightly lower than that of cotton fabric dyed with the reactive dye, 18.52 and 19.36, respectively. The cotton fabric dyed with the reactive dye does not exhibit antibacterial activity against Escherichia coli and Staphylococcus aureus, whereas the antibacterial effectiveness against these bacteria for cotton fabric dyed with DME solution is 99.99 %. The UV protection capability of cotton fabric dyed with DME solution is superior to cotton fabric dyed with the reactive dye. The BOD/COD ratio of wastewater from the dyeing process with DME is higher than that of the reactive dye, with values of 0.70 and 0.32, respectively. The findings of this study indicate the superior ability of using DME solution as compared to the reactive dye, which is promising as a natural dye for fabric in medical applications.

Peroxydisulfate-based Non-radical Oxidation of Rhodamine B by Fe-Mn Doped Granular Activated Carbon: Kinetics and Mechanism Study.

While numerous persulfate-based advanced oxidation processes (AOPs) have been studied based on fancy catalysts, the practical combination of Fe or Mn modified granular activated carbon (GAC) has seldom been investigated. The present study focused on a green and readily synthesized Fe-Mn bimetallic oxide doped GAC (Fe-Mn@GAC), to uncover its catalytic kinetics and mechanism when used in the peroxydisulfate (PDS)-based oxidation process for degrading Rhodamine B (RhB), a representative xenobiotic dye. The synthesized Fe-Mn@GAC was characterized by SEM-EDS, XRD, ICP-OES and XPS analyses to confirm its physicochemical properties. The catalytic kinetics of Fe-Mn@GAC+PDS system were evaluated under varying conditions, including PDS and catalyst dosages, solution pH, and the presence of anions. It was found Fe-Mn@GAC exhibited robust catalytic performance, being insensitive to a wide pH range from 3 to 11, and the presence of anions such as Cl-, SO4 2-, NO3 - and CO3 2-. The catalytic mechanism was investigated by EPR and quenching experiments. The results indicated the catalytic system processed a non-radical oxidation pathway, dominated by direct electron transfer between RhB and Fe-Mn@GAC, with singlet oxygen (1O2) playing a secondary role. The catalytic system also managed to maintain a RhB removal above 81 % in successive 10 cycles, and recover to 89.5 % after simple DI water rinse, showing great reusability. The catalytic system was further challenged by real dye-containing wastewater, achieving a decolorization rate of 84.5 %. This work not only provides fresh insight into the kinetics and mechanism of the Fe-Mn@GAC+PDS catalytic system, but also demonstrates its potential in the practical application in real dye-containing wastewater treatment.

Harnessing iron materials for enhanced decolorization of azo dye wastewater: A comprehensive review.

Highly colored azo dye-contaminated wastewater poses significant environmental threats and requires effective treatment before discharge. The anaerobic azo dye treatment method is a cost-effective and environmentally friendly solution, while its time-consuming and inefficient processes present substantial challenges for industrial scaling. Thus, the use of iron materials presents a promising alternative. Laboratory studies have demonstrated that systems coupled with iron materials enhance the decolorization efficiency and reduce the processing time. To fully realize the potential of iron materials for anaerobic azo dye treatment, a comprehensive synthesis and evaluation based on individual-related research studies, which have not been conducted to date, are necessary. This review provides, for the first time, an extensive and detailed overview of the utilization of iron materials for azo dye treatment, with a focus on decolorization. It assesses the treatment potential, analyzes the influencing factors and their impacts, and proposes metabolic pathways to enhance anaerobic dye treatment using iron materials. The physicochemical characteristics of iron materials are also discussed to elucidate the mechanisms behind the enhanced bioreduction of azo dyes. This study further addresses the current obstacles and outlines future prospects for industrial-scale application of iron-coupled treatment systems.

The self-boosting ultrafast removal of Cr(VI) and organic dye in textile wastewater through sulfite-induced redox processes.

The treatment of textile wastewater containing harmful metal ions poses a significant challenge in industrial applications due to its environmental impact. In this study, the use of sulfite for treating simulated dye wastewater containing New Coccine (NC) and Cr(VI) was investigated. The removal of NC was influenced by the redox reaction between Cr(VI) and sulfite, demonstrating a strong self-boosting effect of Cr(VI) on NC removal. Remarkable NC decoloration (95%) and Cr(VI) reduction (90%) were achieved within 1 min, highlighting the effectiveness of the treatment. Quenching experiments and electron paramagnetic resonance (EPR) technology confirmed that singlet oxygen (1O2) was the main oxidative agent for organic dye removal and SO4•-, •OH and Cr(V) were also identified as key contributors to NC degradation. The Cr(VI)/sulfite system exhibited higher efficiency in degrading azo dyes, such as NC and Congo Red (CR), compared to non-azo dyes like Methylene Blue (MB). This superiority may be attributed to the action of Cr(V) on azo groups. Additionally, the COD removal experiments were conducted on the actual dye wastewater, showing the excellent performance of the Cr(VI)/Sulfite system in treating industrial textile wastewater. This approach presents a promising strategy for effective "waste control by waste", offering great potential for addressing challenges related to dye wastewater treatment and environmental pollution control in practical industrial scenarios.

Synthesis, magnetic properties, biotoxicity and potential mechanism of modified nano zero-valent iron for decolorization of dye wastewater.

SiO2-coated nano zero-valent iron (nZVI) has emerged as a fine material for the treatment of dye wastewater due to its large specific surface area, high surface activity, and strong reducibility. However, the magnetic properties based on which SiO2-coated nZVI (SiO2-nZVI) could effectively separate and recover from treated wastewater, and the biotoxicity analysis of degradation products of the dye wastewater treated by SiO2-nZVI remain unclear. In this study, SiO2-nZVI was synthesized using a modified one-step synthesis method. The SiO2-nZVI nanoparticles were characterized using Transmission electron microscopy, X-ray diffraction, Fourier-transform infrared spectroscopy, Fully automatic specific surface and porosity analyzer, Vibrating sample magnetometer, and Zeta potential analyzer. The removal rate of methyl orange (MO) by SiO2-nZVI composite reached 98.35% when the degradation performance of SiO2-nZVI treating MO was optimized. Since SiO2-nZVI analysed by magnetic hysteresis loops had large saturation magnetization and strong magnetic properties, SiO2-nZVI exhibited excellent ferromagnetic behaviour. The analysis of the degradation products showed that the MO treated by SiO2-nZVI was converted into a series of intermediates, resulting in reducing the toxicity of MO. The potential mechanism of MO degradated by SiO2-nZVI was speculated through degradation process and degradation kinetics analysis. Overall, the SiO2-nZVI composite may be regarded as a promising catalyst for decolorization of dye wastewater.

Degradation of reactive red (B-3BF) dye wastewater using UV irradiation (254/185 nm) with sodium persulfate in a pilot UV device.

Two low-pressure ultraviolet (UV) lamps at 185/254 nm with sodium persulfate in a pilot UV device were utilized for the degradation of reactive red (B-3BF) dye wastewater compared with two UV lamps at 185/185 nm and two UV lamps at 254/254 nm. The degradation performances of UV irradiation (254/185 nm) with sodium persulfate under different degradation times, flow rates, initial pH, initial Na2S2O8 concentrations and initial dye concentrations were investigated. The experimental results illustrated that the degradation percentage of B-3BF dye could reduce to 90.42% with the energy consumption of 85.1 kWh/kg and the residual dye concentration of 1.92 mg/L by UV irradiation (254/185 nm) with initial Na2S2O8 concentration of 1.5 mmol/L and initial dye concentration of 20 mg/L. In addition, degradation performance of B-3BF dye wastewater by UV irradiation (254/185 nm) with sodium persulfate was more effective than those of UV irradiation (254/254 nm) and UV irradiation (185/185 nm). Therefore UV irradiation (254/185 nm) with sodium persulfate was promising for the degradation of B-3BF dye wastewater.

Preparation of CS-LS/AgNPs Composites and Photocatalytic Degradation of Dyes.

Synthetic dyes are prone to water pollution during use, jeopardizing biodiversity and human health. This study aimed to investigate the adsorption and photocatalytic assist potential of sodium lignosulfonate (LS) in in situ reduced silver nanoparticles (AgNPs) and chitosan (CS)-loaded silver nanoparticles (CS-LS/AgNPs) as adsorbents for Rhodamine B (RhB). The AgNPs were synthesized by doping LS on the surface of chitosan for modification. Fourier transform infrared (FT-IR) spectrometry, energy-dispersive spectroscopy (EDS), scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) were used to confirm the synthesis of nanomaterials. The adsorption and photocatalytic removal experiments of RhB were carried out under optimal conditions (initial dye concentration of 20 mg/L, adsorbent dosage of 0.02 g, time of 60 min, and UV power of 250 W), and the kinetics of dye degradation was also investigated, which showed that the removal rate of RhB by AgNPs photocatalysis can reach 55%. The results indicated that LS was highly effective as a reducing agent for the large-scale production of metal nanoparticles and can be used for dye decolorization. This work provides a new catalyst for the effective removal of dye from wastewater, and can achieve high-value applications of chitosan and lignin.

Comparison of treatment performance and microbial community evolution of typical dye wastewater by different combined processes.

The degradation of typical dye wastewater is a focus of research in the printing and dyeing industry. In this study, a combined micro-electrolysis and microbial treatment method was established to treat refractory dye wastewater, and the pivotal factors in the microbial treatment were optimized. In the series and coupled modes, the removal rates of chroma reached 98.75% and 92.50%, and the removal rates of chemical oxygen demand (COD) reached 96.17% and 82.29%, respectively. The high-throughput sequencing results showed that the microbial communities in the microbial system varied at different treatment stages. From the culture stage to the domestication stage, the dominant phylum was Proteobacteria; however, the community abundance of microorganisms decreased. A combination of micro-electrolysis and biological methods can alter the characteristics of the microbial community, increase the number of dominant phyla, and increase the abundance of microorganisms. The degradation effect of the series mode and the overall strengthening effect of micro-electrolysis on the microorganisms were better than those of the coupled mode. In actual wastewater, the maximum removal rates of chroma, COD, total nitrogen (TN), ammonia nitrogen (NH3-N), and total phosphorus (TP) are 97.50%, 98.90%, 94.35%, 93.95%, and 91.17%, respectively. Three-dimensional fluorescence spectrum analysis showed that microbial processes could significantly degrade fluorescent components in wastewater, and methanogenic active enzymes in anaerobic processes could continue to react. The combined process can realize the efficient treatment of toxic dye wastewater by reducing the toxicity of wastewater and efficiently degrading organic matter, which has important guiding significance for the treatment of refractory dye wastewater.

Study on regeneration characteristics of granular activated carbon using ultrasonic and thermal methods.

Dye wastewater is a type of high-concentration, high chromaticity, and high salinity organic wastewater, which is generally treated with activated carbon adsorbent. The effective regeneration of granular activated carbon (GAC) is the key to reducing the operating cost of GAC in the wastewater treatment process. The regeneration characteristics of saturated GAC adsorbed on 288 orange dye wastewater were studied by using the ultrasonic coupled thermal regeneration method. The results showed that the regeneration efficiency of GAC adsorbed on 288 orange dye wastewater increased with the increase of ultrasound power. The optimal ultrasound frequency and regeneration temperature were determined to be 45 kHz and 60 ℃, and the relationship between regeneration times and carbon loss rate was explored. The combination of ultrasound and high-temperature heating methods has successfully improved the regeneration efficiency of GAC and significantly reduced the high-temperature thermal regeneration time of GAC, thereby reducing the mass loss rate of GAC. The performance changes of fresh activated carbon (FAC), saturated activated carbon (SAC), ultrasonic regeneration of activated carbon (UAC), and thermal regeneration of activated carbon (TAC) during the combined regeneration process were explored by characterizing the regenerated GAC. Infrared characterization showed that the C-O group of GAC was significantly weakened after coupling treatment, indicating that ultrasonic treatment can significantly enhance the desorption effect of thermal regeneration. The microjet, shock wave, and cavitation effects generated by ultrasonic treatment restore the specific surface area of GAC, mainly increasing the micropore volume and pore size of GAC, and enhancing the treatment effect of thermal regeneration.

Facile synthesis of lignin-based Fe-MOF for fast adsorption of methyl orange.

To rapidly remove dyes from wastewater, iron-based metal-organic frameworks modified with phenolated lignin (NH2-MIL@L) were prepared by a one-step hydrothermal method. Analyses of the chemical structure and adsorption mechanism of the NH2-MIL@L proved the successful introduction of lignin and the enhancement of its adsorption sites. Compared with NH2-MIL-101-Fe without phenolated lignin, the modification with lignin increased the methyl orange (MO) adsorption rate of NH2-MIL@L. For the best adsorbent, NH2-MIL@L4, the MO adsorption efficiency in MO solution reached 95.09% within 5 min. NH2-MIL@L4 reached adsorption equilibrium within 90 min, exhibiting an MO adsorption capacity of 195.31 mg/g. The process followed pseudo-second-order kinetics and the Dubinin-Radushkevich model. MO adsorption efficiency of NH2-MIL@L4 was maintained at 89.87% after six adsorption-desorption cycles. In mixed solutions of MO and methylene blue (MB), NH2-MIL@L4 achieved an MO adsorption of 94.02% at 5 min and reached MO adsorption equilibrium within 15 min with an MO adsorption capacity of 438.6 mg/g, while the MB adsorption equilibrium was established at 90 min with an MB adsorption rate and capacity of 95.60% and 481.34 mg/g, respectively. NH2-MIL@L4 sustained its excellent adsorption efficiency after six adsorption-desorption cycles (91.2% for MO and 93.4% for MB). The process of MO adsorption by NH2-MIL@L4 followed the Temkin model and pseudo-second-order kinetics, while MB adsorption followed the Dubinin-Radushkevich model and pseudo-second-order kinetics. Electrostatic interactions, π-π interactions, hydrogen bonding, and synergistic interactions affected the MO adsorption process of NH2-MIL@L4.

Preparation of La-doped Ti/SnO2-Sb2O4 anode and its electrochemical oxidation performance of rhodamine B.

In this paper, La-doped Ti/SnO2-Sb2O4 electrode was prepared by electrodeposition and used for electrochemical degradation of rhodamine B. The optimum preparation conditions of the electrode were optimized as deposition time of 15 min and calcination at 500 ℃ for 2 h. The water treatment conditions were selected as initial pH 3.0, electrolyte Na2SO4 concentration 0.1 M, current density 30 mA cm-2, and initial rhodamine B concentration 20 mg L-1; the color and TOC removal of RhB reached 99.78% and 82.41% within 30 min. The FESEM, XRD, XPS, CV, LSV, and EIS characterization studies demonstrated that Ti/SnO2-Sb2O4-1%La electrode had a dense structure and the highest oxygen evolution potential (2.14 V) and lowest charge transfer resistance (0.198 Ω cm-2), indicating that doped La has lower energy consumption. Moreover, La doping can expand the specific surface area, active site, performance of pollutant degradation, and service life of the electrode. Especially, the service life of Ti/SnO2-Sb2O4-1%La is increased by three times, and the maximum life span reaches 90 min (1000 mA cm-2, 1 M H2SO4). Free radical quenching experiments show that ·OH plays a major role in the degradation of RhB. The Ti/SnO2-Sb2O4-1%La electrode prepared in this paper and its results will provide data support and reference for the design of efficient electrocatalytic electrode.

Discerning the catalytic treatment of cationic dye wastewater in photoreactor comprising ternary (Co3+/Co2+)-embedded SnO2/ZnFe2O4 composite sensitive toward ultra-violet illumination.

Herein, magnetic (Co3+/Co2+)-integrated SnO2, SnO2/ZnFe2O4, and ZnFe2O4 composites have been prepared from triply distilled water and 30% of isopropanol in the water medium. The phase evolution, microstructure, and magnetism were investigated successfully and tested for cationic dye wastewater degradation containing Rhodamine 6G and Methylene Blue under ultra-violet irradiation. Composite spheres are attributed to efficient heterojunction interfaces between ZnFe2O4 and SnO2 semiconductors with the support of (Co3+/Co2+) nanoparticles. The results provide a simple, low-cost, environmentally friendly, and scalable method of ternary composites to degrade mixed dyes. Co3+/Co2+-implanted SnO2/ZnFe2O4 offered narrowed bandgap energy, more light absorption, diminishing electron-hole recombination, and more charge carriers toward cationic dye wastewater than the binary components. The rate constant of Rhodamine 6G degradation was observed at 0.0237 min-1, and Methylene Blue degradation was observed at 0.0187 min-1 at 90 min under UV (λ = 365 nm) irradiation. Capturing studies of various organic reactive species and mechanisms of composites was also proposed in detail.

Synergistic molecular mechanism of degradation in dye wastewater by Rhodopseudomonas palustris intimately coupled carbon nanotube - Silver modified titanium dioxide photocatalytic composite with sodium alginate.

The intimately coupled photocatalysis and biodegradation (ICPB), which combined the advantages of high oxidation capacity of photocatalysis and high mineralization rate of biodegradation, has demonstrated excellent removal performance in the degradation of azo dyes with highly toxic, refractory, mutagenic and carcinogenic. In order to explore the metagenomics mechanism of the ICPB system, a novel ICPB was prepared by coupling Rhodopseudomonas palustris (R. Palustris), carbon nanotube - silver modified titanium dioxide photocatalytic composite (CNT-Ag -TiO2, CAT) and sodium alginate (SA) (R. palustris/CAT@SA, R-CAT). Metagenomics sequencing was used to investigate the molecular mechanism of adaptation and degradation of dyes by photosynthetic microorganisms and the adaptive and synergistic interaction between photosynthetic microorganisms and photocatalyst. Experiments on the adaptability and degradability of photosynthetic microorganisms have proved that low concentration azo dyes could be utilized as carbon sources for growth of photosynthetic microorganisms. Metagenomics sequencing revealed that R. palustris was the main degrading bacterium in photosynthetic microorganisms and the functional genes related to carbohydrate metabolism, biological regulation and catalytic activity were abundant. It was found that the addition of photocatalyst significantly up-regulated the functional genes related to the catabolic process, electron transport, oxidoreductase activity and superoxide metabolism of organic matter in the photosynthetic microorganisms. Moreover, many key gene such as alpha-amylase, 1-acyl-sn-glycerol-3-phosphate acyltransferase, aldehyde dehydrogenase enrichment in microbial basal metabolism, such as enoyl-CoA hydratase, malate dehydrogenase, glutathione S-transferase enrichment in degrading azo dyes and electron transport, and many key gene such as undecaprenyl-diphosphatase, carbon storage regulator, DNA ligase enrichment in response to dyes and photocatalysts were discovered. These findings would contribute to a comprehensive understanding of the mechanism of degradation of dye wastewater by ICPB system, a series of genes was produced to adapt to environmental changes, and played synergistic role in terms of intermediate product degradation and electron transfer for degrading azo dyes. The photosynthetic microorganisms might be a promising microorganism for constructing ICPB system.

Clay-moringa seedcake composite for removal of cationic and anionic dyes.

The present study investigated the potential of a composite prepared from kaolinite clay and moringa seedcake in removing methylene blue (MB) and acid orange-7 (AO-7) dyes from aqueous solutions using batch and column tests. The composite was modified using different chemicals during the synthesis process, and the composites were characterised using different techniques such as FTIR, SEM-EDS and XRD. Characterisation showed the presence of actively charged functional groups and porous structure on the composites prepared. Batch tests were performed to assess the effect of operating conditions such as adsorbent dosage, pH, initial dye concentration and contact time. NaOH-modified and H2SO4/NaOH-modified composites demonstrated the highest adsorption capacities for AO-7 and MB, respectively, and were selected for subsequent studies. The adsorption process of dye was best fitted by the Freundlich isotherm and pseudo-second-order kinetic models suggesting that the sorption of MB and AO-7 onto the composites is a heterogeneous, multilayer chemical adsorption process. Long-term fixed-column tests were conducted with the composites to assess the impact of flow rate, bed depth and initial dye concentration on the dye removal efficiency. Optimum removals of 86 and 94%, respectively at pH 2 and pH 10 were obtained for AO-7 and MB in batch tests, along with adsorption capacities of 205.65 and 230.49 mg/g for AO-7 and MB. Results from the column tests were best explained by the Clark model and the Bed Depth-Service Time model. Competing ions impacted the removal of AO-7, while no significant effect was found for MB. The composites could be reused up to four cycles without significantly affecting the adsorption capacity. The present study thus shows the potential of the composite for removal of both the dyes.