ZnFe(PBA)@Ti3C2Tx nanohybrid-based highly sensitive non-enzymatic electrochemical sensor for the detection of glucose in human sweat.

The ZnFe prussian blue analogue [ZnFe(PBA)] was infused with Ti3C2Tx (MXene) denoted as ZnFe(PBA)@Ti3C2Tx and was prepared by an in-situ sonication method to use as a non-enzymatic screen printed electrode sensor. The advantage of non-enzymatic sensors is their excellent sensitivity, rapid detection, low cost and simple design. The synthesized ZnFe(PBA)@Ti3C2Tx was characterized for its physical and chemical characterization by XRD, Raman, XPS, EDAX, and FESEM analysis. It possessed multiple functionalized layers and a cubic structure in the nanohybrid. Further, the sensor was investigated by using electroanalytical studies such as cyclic voltammetry and chronoamperometry analysis. The enhanced surface area with a cubic structure of ZnFe(PBA) and the excellent electrical response of Ti3C2 nanosheet support the advancement of a non-enzymatic electrochemical glucose sensor with improved sensitivity of 973.42 µA mM-1 cm-2 with the limit of detection (LOD) of 3.036 µM (S/N = 3) and linear detection range (LDR) from 0.01 to 1 mM.

A Self-Powered Enzymatic Glucose Sensor Utilizing Bimetallic Nanoparticle Composites Modified Pencil Graphite Electrodes as Cathode.

Enzymatic biofuel cells (EBFC) are promising sources of green energy owing to the benefits of using renewable biofuels, eco-friendly biocatalysts, and moderate operating conditions. In this study, a simple and effective EBFC was presented using an enzymatic composite material-based anode and a nonenzymatic bimetallic nanoparticle-based cathode respectively. The anode was constructed from a glassy carbon electrode (GCE) modified with a multi-walled carbon nanotube (MWCNT) and ferrocene (Fc) as a conductive layer coupled with the enzyme glucose oxidase (GOx) as a sensitive detection layer for glucose. A chitosan layer was also applied to the electrode as a protective layer to complete the composite anode. Chronoamperometry (CA) results show that the MWCNT-Fc-GOx/GCE electrode has a linear relationship between current and glucose concentration, which varied from 1 to 10 mM. The LOD and LOQ were calculated for anode as 0.26 mM and 0.87 mM glucose, respectively. Also the sensitivity of the proposed sensor was calculated as 25.71 µ A/mM. Moreover, the studies of some potential interferants show that there is no significant interference for anode in the determination of glucose except ascorbic acid (AA), uric acid (UA), and dopamine (DA). On the other hand, the cathode consisted of a disposable pencil graphite electrode (PGE) modified with platinum-palladium bimetallic nanoparticles (Nps) which exhibit excellent conductivity and electron transfer rate for the oxygen reduction reaction (ORR). The constructed EBFC was optimized and characterized using various electroanalytical techniques. The EBFC consisting of MWCNT-Fc-GOx/GCE anode and Pt-PdNps/PGE cathode exhibits an open circuit potential of 285.0 mV and a maximum power density of 32.25 µW cm-2 under optimized conditions. The results show that the proposed EBFC consisting of an enzymatic composite-based anode and bimetallic nanozyme-based cathode is a unique design and a promising candidate for detecting glucose while harvesting power from glucose-containing natural or artificial fluids.

Calibration-Free and Highly Sensitive Potentiometric Enzyme-Based Biosensors.

Enzyme-based amperometric biosensors have become popular for healthcare applications. However, they have been under constant pressure for technological innovation to improve their sensitivity and usability. An ideal biosensor has high sensitivity and calibration-free characteristics. This study aims to report enzyme-based glucose and lactate sensors that utilize a proposed "time-derivative of potential (dOCP/dt)" method, with a further aim being to prove theoretically and experimentally that dOCP/dt values are proportional to substrate concentration. High sensitivity is obtained regardless of the electrode size because the electrode potential is independent of the electrode area in the biosensor. Importantly, because the substrate diffusion determines the enzyme reaction rate on the sensors, the dOCP/dt biosensors can essentially eliminate external influences such as temperature and pH. The result is the successful realization of a biosensor that is calibration-free, making it a much more practical option.

Glucose detection: In-situ colorimetric analysis with double-layer hydrogel microneedle patch based on polyvinyl alcohol and carboxymethyl chitosan.

Skin interstitial fluid (ISF) has emerged as a significant reservoir of biomarkers for disease diagnosis and prevention. Microneedle (MN) patches are regarded as an optimal platform for ISF extraction from the skin due to their non-invasive nature. However, challenges such as prolonged sampling durations and complex detection procedures impede timely metabolic analysis. In this investigation, we amalgamated MN technology with immobilized enzyme technology to fabricate a dual-layer MN patch integrating sampling and detection functionalities, thereby enabling in-situ colorimetric detection of hyperglycemia. The tip layer of the patch, comprising polyvinyl alcohol/carboxymethyl chitosan (PVA/CMCS) MN, was synthesized utilizing a chemical crosslinking approach for the first time, with glucose oxidase (GOx) being incorporated. The hydrophilicity of CMCS expedited the extraction process, facilitating the retrieval of approximately 10 mg of ISF within 10 min. The backing layer consisted of an immobilized polyvinyl alcohol-chitosan-horseradish peroxidase (PVA-CS-HRP) hydrogel film loaded with 3,3', 5,5'-tetramethylbenzidine (TMB). Incorporating macromolecular polymer PVA and CS for HRP immobilization addressed the issue of poor stability associated with traditional natural enzymes, thereby enhancing the sensitivity of the reaction system. The in-situ colorimetric sensor facilitated minimally invasive ISF extraction and swift conversion of glucose levels into detectable color changes.

Chemosensitive Properties of Electrochemically Synthesized Poly-3-Thienylboronic Acid: Conductometric Detection of Glucose and Other Diol-Containing Compounds under Electrical Affinity Control.

Due to the presence of the boronic acid moieties, poly-3-thienylboronic acid has an affinity for saccharides and other diol-containing compounds. Thin films of this novel chemosensitive polymer were synthesized electrochemically on the gold surface. The adhesion of the polymer was enhanced by the deposition of a monomolecular layer of thiophenol. The technology was used to fabricate conductometric sensors for glucose and other diol-containing compounds. Simultaneous two- and four-electrode conductivity measurements were performed. The chemical sensitivity to sorbitol, fructose, glucose, and ethylene glycol was studied at different pH and electrode potentials, and the corresponding binding constants were obtained. Depending on the electrode potential, the reciprocal values of the binding constants of glucose to poly-3-thienylboronic acid at neutral pH are in the range of 0.2 mM-1.0 mM. The affinity for glucose has been studied in buffer solutions and in solutions containing the major components of human blood. It was shown that the presence of human serum albumin increases the affinity of poly-3-thienylboronic acid for diol-containing compounds.

Conformal sulfidation of HKUST-1 for constructing porous Cu2S/CuO octahedrons realizing highly sensitive non-enzymatic glucose detection.

Metal-organic frameworks (MOFs) are believed to be promising precursors for constructing novel and efficient catalysts for glucose sensing. Herein, HKUST-1 precursors are first fabricated using a one-pot hydrothermal approach, and then HKUST-1 is converted into porous Cu2S/CuO octahedrons through conformal sulfidation with the help of OH-ions. The as-obtained Cu2S/CuO composite can provide rich electrochemical active sites and promoted electric transfer kinetics. Benefiting from these combined merits, the as-fabricated Cu2S/CuO composite is confirmed to be a high-performance catalyst, with high sensitivities of 8269.45 and 4140.82µA mM-1cm-2in the corresponding ranges of 0.05 ∼ 0.6 mM and 0.6 ∼ 1.2 mM, respectively. Moreover, the as-prepared electrode materials possess good anti-interference ability, reproducibility and long-term stability. This work opens up new avenues for the design and preparation of transition metal sulfide composites.

CuxO decorated Ti3C2Tx MXene composites for non-enzymatic glucose sensing with large linear ranges.

Ti3C2Tx MXene/CuxO composites were prepared by acid etching combined with electrochemical technique. The abundant active sites on the surface of MXene greatly increase the loading of CuxO nanoparticles, and the synergistic effect between the different components of the composite can accelerate the oxidation reaction of glucose. The results indicate that at the working potential of 0.55 V (vs. Ag/AgCl), the glucose sensor based on Ti3C2Tx MXene/CuxO composite presents large linear concentration ranges from 1 µM to 4.655 mM (sensitivity of 361 µA mM-1 cm-2) and from 5.155 mM to 16.155 mM (sensitivity of 133 µA mM-1 cm-2). The limit of detection is 0.065 µM. In addition, the sensor effectively avoids the oxidative interference of common interfering species such as ascorbic acid, dopamine and uric acid. The sensor has good reproducibility, stability and acceptable recoveries for the detection of glucose in human sweat sample (97.5-103.3%) with RSD values less than 4%. Based on these excellent properties it has great potential for the detection of glucose in real samples.

Nickel foam-loaded Co-MOF@TiO2/MoS2 as electrode materials for dual-function devices for glucose detection and hydrogen evolution.

Dual-functional nanomaterial electrodes have the capability to satisfy the requirements for both sweat analysis and the hydrogen evolution reaction (HER), thereby enabling the integration of electrochemical sensing and hydrogen production. In this study, ZIF-67 cubes are synthesized on nickel foam (NF), while TiO2 is obtained through an annealing process. Subsequently, the ZIF-67@TiO2/MoS2 nanocomposite is fabricated on nickel foam via a hydrothermal method. This composite material exhibits exceptional photocatalytic properties and is also suitable for the detection of glucose in sweat. The glucose detection range spans from 10 nM to 10 mM with a sensitivity of 7.24 µA mM-1 cm-2 for a signal-to-noise ratio of 3 and a detection limit of 0.43 µM. Moreover, when utilized as a hydrogen evolution electrode, this material demonstrates a current density of 10 mA cm-2 at an overpotential of 118 mV, with a Tafel slope of 73 mV/dec. The synthesis process is both straightforward and economical. This research introduces a novel concept for the design of multifunctional chemical sensors.

Embroidered Interdigitated Electrodes (IDTs) with Wireless Readout for Continuous Biomarker Monitoring.

Non-invasive continuous health monitoring has become feasible with the advancement of biosensors. While monitoring certain biomarkers such as heart rate or skin temperature are now at a certain maturity, monitoring molecular biomarkers is still challenging. Progress has been shown in sampling, measurement, and interpretation of data toward non-invasive molecular sensors that can be integrated into daily wearable items. Toward this goal, this paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. In controlled experiments, we have shown the variation of glucose concentration in water can be wirelessly detected by tracking the resonant frequency of the embroidered sensors. The current sensors operate at 1.8 GHz to 2 GHz and respond to the change in glucose concentration with a sensitivity of 0.17 MHz/(mg/dL). The embroidered IDT-based sensors with wireless sensing will be a new measurement modality for molecular wearable sensors. The establishment of a wireless sensing mechanism for embroidered IDT-based sensors will be followed by an investigation of sweat for molecular detection. This will require adding functionalities for sampling and interpretation of acquired data. We envisage the embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Technology in the management of diabetes in hospitalised adults.

Suboptimal glycaemic management in hospitals has been associated with adverse clinical outcomes and increased financial costs to healthcare systems. Despite the availability of guidelines for inpatient glycaemic management, implementation remains challenging because of the increasing workload of clinical staff and rising prevalence of diabetes. The development of novel and innovative technologies that support the clinical workflow and address the unmet need for effective and safe inpatient diabetes care delivery is still needed. There is robust evidence that the use of diabetes technology such as continuous glucose monitoring and closed-loop insulin delivery can improve glycaemic management in outpatient settings; however, relatively little is known of its potential benefits and application in inpatient diabetes management. Emerging data from clinical studies show that diabetes technologies such as integrated clinical decision support systems can potentially mediate safer and more efficient inpatient diabetes care, while continuous glucose sensors and closed-loop systems show early promise in improving inpatient glycaemic management. This review aims to provide an overview of current evidence related to diabetes technology use in non-critical care adult inpatient settings. We highlight existing barriers that may hinder or delay implementation, as well as strategies and opportunities to facilitate the clinical readiness of inpatient diabetes technology in the future.

Controlled synthesized of ternary Cu-Co-Ni-S sulfides nanoporous network structure on carbon fiber paper: a superior catalytic electrode for highly-sensitive glucose sensing.

BACKGROUND: Efficient monitoring of glucose concentration in the human body necessitates the utilization of electrochemically active sensing materials in nonenzymatic glucose sensors. However, prevailing limitations such as intricate fabrication processes, lower sensitivity, and instability impede their practical application. Herein, ternary Cu-Co-Ni-S sulfides nanoporous network structure was synthesized on carbon fiber paper (CP) by an ultrafast, facile, and controllable technique through on-step cyclic voltammetry, serving as a superior self-supporting catalytic electrode for the high-performance glucose sensor. RESULTS: The direct growth of free-standing Cu-Co-Ni-S on the interconnected three-dimensional (3D) network of CP boosted the active site of the composites, improved ion diffusion kinetics, and significantly promoted the electron transfer rate. The multiple oxidation states and synergistic effects among Co, Ni, Cu, and S further promoted glucose electrooxidation. The well-architected Cu-Co-Ni-S/CP presented exceptional electrocatalytic properties for glucose with satisfied linearity of a broad range from 0.3 to 16,000 µM and high sensitivity of 6829 µA mM- 1 cm- 2. Furthermore, the novel sensor demonstrated excellent selectivity and storage stability, which could successfully evaluate the glucose levels in human serum. Notably, the novel Cu-Co-Ni-S/CP showed favorable biocompatibility, proving its potential for in vivo glucose monitoring. CONCLUSION: The proposed 3D hierarchical morphology self-supported electrode sensor, which demonstrates appealing analysis behavior for glucose electrooxidation, holds great promise for the next generation of high-performance glucose sensors.

Cu/Cu2O/C nanoparticles and MXene based composite for non-enzymatic glucose sensors.

Copper/Cuprous oxide/Carbon nanoparticles decorated MXene composite was prepared and subsequently examined for its potential application as a non-enzymatic glucose sensor. To carry out this, initially the Cu MOF/MXene composite was synthesised by the hydrothermal method and was annealed in an unreacted environment at different time intervals. During this process, petal like Cu MOF on MXene loses the organic ligands to form a Cu/Cu2O/C based nanoparticles on MXene. Further, an electrode was fabricated with the developed material for understanding the sensing performance by cyclic voltammetry and chronoamperometry in 0.1 M NaOH solution. Results reveal that the highest weight percentage of copper oxide in the composite (15 min of annealed material) shows a higher electro catalytic activity for sensing glucose molecules due to more active sites with good electron transfer ability in the composite. The formed composite exhibits a wide linear range of 0.001-26.5 mM, with a sensitivity of 762.53µAmM-1cm-2(0.001-10.1 mM), and 397.18µAmM-1cm-2(11.2-26.9 mM) and the limit of detection was 0.103µM. In addition to this, the prepared electrode shows a good reusability, repeatability, selectivity with other interferences, stability (93.65% after 30 days of storage), and feasibility of measuring glucose in real samples. This finding reveals that the metal oxide derived from MOF based nanoparticle on the MXene surface will promote the use of non-enzymatic glucose sensors.

Smartphone based wearable sweat glucose sensing device correlated with machine learning for real-time diabetes screening.

BACKGROUND: Diabetes is a significant health threat, with its prevalence and burden increasing worldwide indicating its challenge for global healthcare management. To decrease the disease severity, the diabetic patients are recommended to regularly check their blood glucose levels. The conventional finger-pricking test possesses some drawbacks, including painfulness and infection risk. Nowadays, smartphone has become a part of our lives offering an important benefit in self-health monitoring. Thus, non-invasive wearable sweat glucose sensor connected with a smartphone readout is of interest for real-time glucose detection. RESULTS: Wearable sweat glucose sensing device is fabricated for self-monitoring of diabetes. This device is designed as a body strap consisting of a sensing strip and a portable potentiostat connected with a smartphone readout via Bluetooth. The sensing strip is modified by carbon nanotubes (CNTs)-cellulose nanofibers (CNFs), followed by electrodeposition of Prussian blue. To preserve the activity of glucose oxidase (GOx) immobilized on the modified sensing strip, chitosan is coated on the top layer of the electrode strip. Herein, machine learning is implemented to correlate between the electrochemical results and the nanomaterial content along with deposition cycle of prussian blue, which provide the highest current response signal. The optimized regression models provide an insight, establishing a robust framework for design of high-performance glucose sensor. SIGNIFICANCE: This wearable glucose sensing device connected with a smartphone readout offers a user-friendly platform for real-time sweat glucose monitoring. This device provides a linear range of 0.1-1.5 mM with a detection limit of 0.1 mM that is sufficient enough for distinguishing between normal and diabetes patient with a cut-off level of 0.3 mM. This platform might be an alternative tool for improving health management for diabetes patients.

All-printed wearable biosensor based on MWCNT-iron oxide nanocomposite ink for physiological level detection of glucose in human sweat.

Wearable sensors for sweat glucose monitoring are gaining massive interest as a patient-friendly and non-invasive way to manage diabetes. The present work offers an alternative on-body method employing an all-printed flexible electrochemical sensor to quantify the amount of glucose in human sweat. The working electrode of the glucose sensor was printed using a custom-formulated ink containing multi-walled carbon nanotube (MWCNT), poly (3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOPT: PSS), and iron (II, III) oxide (Fe3O4) nanoparticles. This novel ink composition has good conductivity, enhanced catalytic activity, and excellent selectivity. The working electrode was modified using Prussian blue (PB) nanoparticles and glucose oxidase enzyme (GOx). The sensor displayed a linear chronoamperometric response to glucose from 1 µM to 400 µM, with a precise detection limit of ∼0.38 µM and an impressive sensitivity of ∼4.495 µAµM-1cm-2. The sensor stored at 4 °C exhibited excellent stability over 60 days, high selectivity, and greater reproducibility. The glucose detection via the standard addition method in human sweat samples acquired a high recovery rate of 96.0-98.6%. Examining human sweat during physical activity also attested to the biosensor's real-time viability. The results also show an impressive correlation between glucose levels obtained from a commercial blood glucose meter and sweat glucose concentrations. Remarkably, the present results outperform previously published printed glucose sensors in terms of detection range, low cost, ease of manufacturing, stability, selectivity, and wearability.

Iridium oxide-based non-enzymatic glucose sensor: Superior electro-catalytic performance in biological environmental media.

Nanostructured inorganic materials have potential advantages as glucose-sensing elements in diabetes care, thereby circumventing the need for expensive enzymatic agents. However, many nonenzymatic sensors face challenges related to selectivity and reliability, reducing their efficacy in body fluids. In this study, we introduce an Iridium oxide (IrO2)-based non-enzymatic glucose sensor. This sensor demonstrates exceptional electro-catalytic properties in human serum, characterized by high sensitivity (638 µA µM-1cm2) and a consistent recovery rate (∼104%) across 15 cycles in saline. Furthermore, its impressive performance in human serum, as evidenced by a low relative standard deviation (RSD <1.57%), underscores its applicability in biological matrices such as interstitial fluids. Overall, the IrO2 sensor is a promising, highly reversible, economical, and simple method for detecting glucose in continuous monitoring systems.

In situ anchored ternary hierarchical hybrid nickel@cobaltous sulfide on poly(3,4-ethylenedioxythiophene)-reduced graphene oxide for highly efficient non-enzymatic glucose sensing.

A ternary hierarchical hybrid Ni@CoxSy/poly(3,4-ethylenedioxythiophene)-reduced graphene oxide (Ni@CoxSy/PEDOT-rGO) is rationally designed and in situ facilely synthesized as electrocatalyst to construct a binder-free sensing platform for non-enzymatic glucose monitoring through traditional electrodeposition procedure. The as-prepared Ni@CoxSy/PEDOT-rGO presents unique hierarchical structure and multiple valence states as well as strong and robust adhesion between Ni@CoxSy/PEDOT-rGO and GCE. Profiting from the aforementioned merits, the sensing platform constructed under optimal conditions achieved a wide detection range (0.2 µM ~ 2.0 mM) with high sensitivity (1546.32 µA cm-2 mM-1), a rapid response time (5 s), an ultralow detection limit (0.094 µM), superior anti-interference performance, excellent reproducibility and considerable stability. Furthermore, the sensor demonstrates an acceptable accuracy and appreciable recoveries ranging from 90.0 to 102.0% with less than 3.98% RSD in human blood serum samples, indicating the prospect of the sensor for the real samples analysis. It will provide a strategy to rationally design and fabricate ternary hierarchical hybrid as nanozyme for glucose assay.

Tailoring the d-band center on Ru1Cu single-atom alloy nanotubes for boosting electrochemical non-enzymatic glucose sensing.

The development of cost-effective and highly efficient electrocatalysts is critical to help electrochemical non-enzymatic sensors achieve high performance. Here, a new class of catalyst, Ru single atoms confined on Cu nanotubes as a single-atom alloy (Ru1Cu NTs), with a unique electronic structure and property, was developed to construct a novel electrochemical non-enzymatic glucose sensor for the first time. The Ru1Cu NTs with a diameter of about 24.0 nm showed a much lower oxidation potential (0.38 V) and 9.0-fold higher response (66.5 µA) current than Cu nanowires (Cu NWs, oxidation potential 0.47 V and current 7.4 µA) for glucose electrocatalysis. Moreover, as an electrochemical non-enzymatic glucose sensor, Ru1Cu NTs not only exhibited twofold higher sensitivity (54.9 µA mM-1 cm-2) and wider linear range (0.5-8 mM) than Cu NWs, but also showed a low detection limit (5.0 µM), excellent selectivity, and great stability. According to theoretical calculation results, the outstanding catalytic and sensing performance of Ru1Cu NTs could be ascribed to the upshift of the d-band center that helped promote glucose adsorption. This work presents a new avenue for developing highly active catalysts for electrochemical non-enzymatic sensors.

Design and Synthesis of Transferrable Macro-Sized Continuous Free-Standing Metal-Organic Framework Films for Biosensor Device.

Metal organic framework (MOF) films have attracted abundant attention due to their unique characters compared with MOF particles. But the high-temperature reaction and solvent corrosion limit the preparation of MOF films on fragile substrates, hindering further applications. Fabricating macro-sized continuous free-standing MOF films and transferring them onto fragile substrates are a promising alternative but still challenging. Here, a universal strategy to prepare transferrable macro-sized continuous free-standing MOF films with the assistance of oxide nanomembranes prepared by atomic layer deposition and studied the growth mechanism is developed. The oxide nanomembranes serve not only as reactant, but also as interfacial layer to maintain the integrality of the free-standing structure as the stacked MOF particles are supported by the oxide nanomembrane. The centimeter-scale free-standing MOF films can be transferred onto fragile substrates, and all in one device for glucose sensing is assembled. Due to the strong adsorption toward glucose molecules, the obtained devices exhibit outstanding performance in terms of high sensitivity, low limit of detection, and long durability. This work opens a new window toward the preparation of MOF films and MOF film-based biosensor chip for advantageous applications in post-Moore law period.

Single-Component Electroactive Polymer Architectures for Non-Enzymatic Glucose Sensing.

Organic mixed ionic-electronic conductors (OMIECs) have emerged as promising materials for biological sensing, owing to their electrochemical activity, stability in an aqueous environment, and biocompatibility. Yet, OMIEC-based sensors rely predominantly on the use of composite matrices to enable stimuli-responsive functionality, which can exhibit issues with intercomponent interfacing. In this study, an approach is presented for non-enzymatic glucose detection by harnessing a newly synthesized functionalized monomer, EDOT-PBA. This monomer integrates electrically conducting and receptor moieties within a single organic component, obviating the need for complex composite preparation. By engineering the conditions for electrodeposition, two distinct polymer film architectures are developed: pristine PEDOT-PBA and molecularly imprinted PEDOT-PBA. Both architectures demonstrated proficient glucose binding and signal transduction capabilities. Notably, the molecularly imprinted polymer (MIP) architecture demonstrated faster stabilization upon glucose uptake while it also enabled a lower limit of detection, lower standard deviation, and a broader linear range in the sensor output signal compared to its non-imprinted counterpart. This material design not only provides a robust and efficient platform for glucose detection but also offers a blueprint for developing selective sensors for a diverse array of target molecules, by tuning the receptor units correspondingly.

Achieving Biomedically Desirable Nitric Oxide Release from Glucose Monitor Surfaces Via a Cu-Based Catalyst Coating.

We report the design of a blood-contacting glucose monitor with a nitric oxide (NO)-releasing metal-organic framework (MOF) embedded within the outer polymer layer of a glucose sensor to promote the release of NO from endogenous NO donors. The sensors were tested by using amperometry across a range of glucose concentrations to assess whether the presence of either the MOF or NO decreased the performance of the glucose monitor. Even though signal response was diminished, the sensors maintained a good regression fit (R2 = 0.9944) and a similar dynamic range and reproducibility in the presence of S-nitrosoglutathione.