Accuracy of Mandibular Removable Partial Denture Frameworks Fabricated by 3D Printing and Conventional Techniques.

Herein, we used digital superimposition to evaluate the accuracy of metal frameworks for mandibular removable partial dentures fabricated using three techniques. Thirty master casts of a mandibular dentiform were categorized into three groups (n = 10) based on the framework manufacturing method: selective laser melting-based metal three-dimensional (3D) printing (SLM), digital light projection-based resin 3D printing and subsequent casting (RPC), and conventional casting (CON). The master casts were scanned twice, initially after preparation and subsequently after attaching silicone using the frameworks. These scan files were digitally superimposed to measure the silicone thickness. Statistical analysis was conducted using SPSS Statistics (Version 23.0, IBM Corp., Somers, NY, USA). One-way ANOVA and a post hoc Tukey's multiple comparison tests were performed to determine differences among the three groups (α = 0.05). The RPC group exhibited significantly higher overall and mean internal discrepancies at rest and tissue stops than the SLM and CON groups, which exhibited statistically insignificant differences. Thus, SLM fabrication resulted in comparable accuracy to that achieved by CON, whereas sequentially performing resin 3D printing and casting induced inferior accuracy. However, all frameworks across the three groups were clinically acceptable.

A Pragmatic Approach for Rapid, Non-Destructive Assessment of Defect Types in Laser Powder Bed Fusion Based on Melt Pool Monitoring Data.

Process monitoring systems, e.g., systems based on photodiodes, could be used in laser-based powder bed fusion (PBF-LB/M) to measure various process parameters and process signatures to eventually allow for a local, detailed analysis of the produced parts. Here, simple statements only concerning the occurrence of defects in parts are sufficient in many cases, especially with respect to industrial application. Therefore, a pragmatic approach to rapidly infer the occurrence of defects and their types based on in situ data obtained by commercially available process monitoring systems is introduced. In this approach, a color distribution in form of a histogram is determined for each produced part using layer-wise screenshots of the visualized data provided by the monitoring software. Assessment of the histograms of AlSi10Mg samples, which were processed with different parameter combinations, revealed characteristics depending on the prevailing defect types. These characteristics enable the prediction of the occurring defect types without the necessity to apply conventional downstream testing methods, and thus, a straightforward separation of parts with good quality from defective components. Since the approach presented uses the data visualization of the monitoring software, it can be used even when direct access to the raw data is not provided by the machine manufacturer.

Favorable efficacy and reduced acute neurotoxicity by antisense oligonucleotides with 2',4'-BNA/LNA with 9-(aminoethoxy)phenoxazine.

An increasing number of antisense oligonucleotides (ASOs) have been approved for clinical use. However, improvements of both efficacy and safety in the central nervous system (CNS) are crucial for the treatment with CNS diseases. We aimed to overcome the crucial issues by our development of various gapmer ASOs with a novel nucleoside derivative including a 2',4'-BNA/LNA with 9-(aminoethoxy)phenoxazine (BNAP-AEO). The various gapmer ASOs with BNAP-AEO were evaluated for thermal stability, in vitro and in vivo efficacy, and acute CNS toxicity. Thermal stability analysis of the duplexes with their complementary RNAs showed that ASOs with BNAP-AEO had a higher binding affinity than those without BNAP-AEO. In vitro assays, when transfected into neuroblastoma cell lines, demonstrated that ASOs with BNAP-AEO, had a more efficient gene silencing effect than those without BNAP-AEO. In vivo assays, involving intracerebroventricular injections into mice, revealed ASOs with BNAP-AEO potently suppressed gene expression in the brain. Surprisingly, the acute CNS toxicity in mice, as assessed through open field tests and scoring systems, was significantly lower for ASOs with BNAP-AEO than for those without BNAP-AEO. This study underscores the efficient gene-silencing effect and low acute CNS toxicity of ASOs incorporating BNAP-AEO, indicating the potential for future therapeutic applications.

Fatty Acid Profile and Thermal Behavior of Fat-Rich Edible Insect Oils Compared to Commonly Consumed Animal and Plant Oils.

This study compared the physicochemical properties of edible insect oils from silkworm (Bombyx mori) pupa (SP), sago palm weevil (Rhynchophorus ferrugineus) larva (PW), and bamboo caterpillar (Omphisa fuscidentalis; BC) to oils from chicken skin (CK), beef back fat (BF), pork back fat (PF), salmon belly (SB), sea bass belly (BB), coconut (C), and peanut (P). The fatty acid profiles and thermal behaviors (crystallization and melting) of the extracted oils were evaluated. PW and BC oils had more saturated fatty acids (SFAs) than CK, PF, SB, BB, and P oils. SP oil had equivalent SFA content to CK and BB oils. Insect oils exhibited similar monounsaturated fatty acid concentrations in all samples, except C oils. PW and BC oils exhibited a higher content of palmitoleic acid than the other oils. SP oils contained polyunsaturated fatty acids similar to those in SB and BB oils, which were higher than those in PW, BC, CK, BF, and PF oils. SP oil also exhibited the highest concentration of α-linolenic acid (C18:3 n-3). Arachidonic acid (0.01-0.02 g/100 g) in all insect oils was lower level compared to CK, BF, PF, SB, and BB oils. SP oil (0.03 g/100 g) exhibited a slightly higher level of eicosapentaenoic acid compared to PW (0.01 g/100 g) and BC (0.01 g/100 g) oils. The insect oils were liquid at ambient temperature, solid below -15°C, and required less energy (△Hm-max) for melting than other samples. This study indicated that insects, particularly SP, could serve as an alternative source of fat to meet its growing demand.

Mineral transformation and solidification of heavy metals during co-melting of MSWI fly ash with coal fly ash.

Melting is an efficient method to turn municipal solid waste incineration (MSWI) fly ash (FA) into non-hazardous material. Coal fly ash (CFA) was selected as the silica-alumina source to carry out co-melting research with MSWI FA in this work. The effects of the temperature and the CFA content on mineral transformation and the migration characteristics of heavy metals were analyzed. The results showed that the mixtures of MSWI FA and CFA reacted at high temperatures to mainly generate Ca2Al2SiO7, Ca2SiO4, and CaAl2Si2O8 primarily and then melted and formed the amorphous-phase vitreous body when the CFA content was more than 40% and the temperature was higher than 1300 °C. During the melting process, Cd and Pb were almost volatilized, while Cr, Mn, and Ni were almost retained. Besides, the volatilization rates of Cu and Zn fluctuated with the temperature and the CFA content. Suitable treatment temperature and CFA content were conducive to the transformation of the heavy metals in the FA into stable forms, and the melting products were no longer hazardous wastes because the vitreous body could effectively encapsulate heavy metals. This study aims to help reuse the FA and CFA collaboratively and be more environmentally friendly.

Evaluation of the FPMC respiratory panel for detection of respiratory tract pathogens in nasopharyngeal swab and sputum specimens.

OBJECTIVES: The performance of the new Respiratory Pathogen panel (fluorescent probe melting curve, FPMC) for the qualitative detection of 12 organisms (chlamydia pneumoniae, mycoplasma pneumoniae, adenovirus, influenza A virus, influenza B virus, parainfluenza virus, rhinovirus, etc.) was assessed. METHODS: Prospectively collected nasopharyngeal swab (NPS) and sputum specimens (n = 635) were detected by using the FPMC panel, with the Sanger sequencing method as the comparative method. RESULTS: The overall percent concordance between the FPMC analysis method and the Sanger sequencing method was 100% and 99.66% for NPS and sputum specimens, respectively. The FPMC testified an overall positive percent concordance of 100% for both NPS and sputum specimens. The FPMC analysis method also testified an overall negative percent concordance of 100% and 99.38% for NPS and sputum specimens, respectively. CONCLUSIONS: The FPMC analysis method is a stable and accurate assay for rapid, comprehensive detecting for respiratory pathogens.

Predictive model for the surface melting and puffing of freeze-dried amorphous materials.

It is thought that surface melting and puffing of freeze-dried amorphous materials are related to the difference between the surface temperature (Tsur) and freeze-concentrated glass transition temperature (Tg') of the materials. Although Tg' is a material-specific parameter, Tsur is affected by the type and amount of solute and freeze-drying conditions. Therefore, it will be practically useful for preventing surface melting and puffing if Tsur can be calculated using only the minimum necessary parameters. This study aimed to establish a predictive model for the surface melting and puffing of freeze-dried amorphous materials according to the calculated Tsur. First, a Tsur-predictive model was proposed under the thermodynamic equilibrium assumptions. Second, solutions with various solute mass fractions of sucrose, maltodextrin, and sucrose-maltodextrin mixture were prepared, and three material-specific parameters (Tg', unfrozen water content, and true density) were experimentally determined. According to the proposed model with the parameters, the Tsur of the samples was calculated at chamber pressures of 13, 38, and 103 Pa. The samples were freeze-dried at the chamber pressures, and their appearance was observed. As expected, surface melting and puffing occurred at calculated Tsur > Tg' with some exceptions. The water activity (aw) of the freeze-dried samples increased as the Tsur - Tg' increased. This will have resulted from surface melting and puffing, which created a covering film, thereby preventing subsequent dehydration. The observations suggest that the proposed model is also useful for predetermining the drying efficiency and storage stability of freeze-dried amorphous materials.

Bauxite residue (red mud) treatment: Current situation and promising solution.

Bauxite residue, an industrial solid waste generated during alumina production, with over 80 % of bauxite residue worldwide being accumulated around alumina plants, which occupying a significant amount of land resources and posing a threat to the natural environment in the surrounding areas. This paper reviews recent advances in extracting valuable resources from bauxite residue, and its applications in building materials, environmental adsorbents, energy storage materials, and soil alkalinization. It also highlighted the main problem existing in these researches, which is the inability of the existing single processes to achieve the comprehensive utilization of various types of bauxite residue or maximize the utilization of bauxite residue components, resulting in a low comprehensive utilization rate and insignificant absorption effects of bauxite residue. To address these issues, we proposed a strategy of classifying and utilizing bauxite residue based on its components and establishing a multi-industry application system, involving sectors such as steel and building materials. This collaborative approach aims to handle various types of bauxite residue more effectively. Additionally, we suggest selecting suitable treatment methods based on the specific characteristics of bauxite residue and implementing measures to promote its comprehensive and large-scale utilization.

A Novel Multiplex LAMP Assay for the Detection of Respiratory Human Adenoviruses.

Human adenoviruses (HAdVs) are common pathogens that are associated with a variety of diseases, including respiratory tract infections (RTIs). Without reliable, fast, and cost-effective detection methods for HAdVs, patients may be misdiagnosed and inappropriately treated. To address this problem, we have developed a multiplex loop-mediated isothermal amplification (LAMP) assay for the detection of the species Human adenovirus B (HAdV-B), Human adenovirus C (HAdV-C) and Human adenovirus E (HAdV-E) that cause RTIs. This multiplexing approach is based on the melting curve analysis of the amplicons with a specific melting temperature for each HAdV species. Without the need for typing of HAdVs, the LAMP results can be visually detected using colorimetric analysis. The assay reliably detects at least 375 copies of HAdV-B and -C and 750 copies of HAdV-E DNA per reaction in less than 35 min at 60 °C. The designed primers have no in silico cross-reactivity with other human respiratory pathogens. Validation on 331 nasal swab samples taken from patients with RTIs showed a 90-94% agreement rate with our in-house multiplex quantitative polymerase chain reaction (qPCR) method. Concordance between the quantitative and visual LAMP was 99%. The novel multiplexed LAMP could be an alternative to PCR for diagnostic purposes, saving personnel and equipment time, or could be used for point-of-care testing.

The Use of Carrot Fiber and Some Gums in the Production of Block-Type Melting Cheese.

In this study, the effect of carrot fiber and certain gums on the physicochemical, textural, microbiological, and sensory properties of block-type melting cheese, which holds a significant place in our daily food consumption, was investigated. The study also aimed to determine the impact of carrot fiber and other gums on cheese properties, as well as on yield and meltability. Carrot fiber was used at levels of 2.5% and 5.0% by weight, while carrageenan and xanthan gum were each used at levels of 0.25% and 0.50%. The cheeses were analyzed on days 1, 15, and 30. At the end of the study, it was determined that the highest total dry matter, fat, and protein values were found in the control sample due to the addition of water when preparing the cheeses with fiber and gum. The highest dry matter, fat, salt, and protein ratios were 59.65%, 29.40%, 1.48%, and 24.48%, respectively, in the control sample. The lowest fat, salt, and protein ratios were 25.00%, 1.31%, and 22.07%, respectively, in the 5.0% carrot fiber sample. The lowest dry matter value was found in the 0.5% xanthan sample, namely 53.62%. The highest L* value was measured in the control sample at 86.89, while the lowest was measured in the 5.0% carrot fiber sample at 81.86. The lowest a* and b* values were 2.82 and 29.42, respectively, in the control sample, while the highest values were 6.20 and 37.37, respectively, in the 5.0% carrot fiber sample. It was observed that the use of carrot fiber imparted an orangish color to the cheese. It was observed that the pH values of the samples were similar. According to the sensory evaluation results, the most liked sample was the control sample with 8.5 points, followed by the 0.25% xanthan sample with 8.0 points. The 5.0% carrot fiber sample received the lowest sensory appreciation with 6.1 points. It was understood that the use of carrot fiber gave the cheese an orangish color. Although the meltability varied according to the amount of gum and fiber used, it was measured at 6.92 cm in the 0.25% carrageenan sample on the first day and at 6.79 cm in the control sample on the last day of storage. It was observed that the use of fiber decreased the total bacterial count, while the use of gum increased it.

High-Resolution Melting (HRM) analysis of DNA methylation using semiconductor chip-based digital PCR.

BACKGROUND: Digital PCR (dPCR) technology allows absolute quantification and detection of disease-associated rare variants, and thus the use of dPCR technology has been increasing in clinical research and diagnostics. The high-resolution melting curve analysis (HRM) of qPCR is widely used to distinguish true positives from false positives and detect rare variants. In particular, qPCR-HRM is commonly used for methylation assessment in research and diagnostics due to its simplicity and high reproducibility. Most dPCR instruments have limited fluorescence channels available and separate heating and imaging systems. Therefore, it is difficult to perform HRM analysis using dPCR instruments. OBJECTIVE: A new digital real-time PCR instrument (LOAA) has been recently developed to integrate partitioning, thermocycling, and imaging in a single dPCR instrument. In addition, a new technique to perform HRM analysis is utilized in LOAA. The aim of the present study is to evaluate the efficiency and accuracy of LOAA dPCR on HRM analysis for the detection of methylation. METHODS: In this study, comprehensive comparison with Bio-Rad qRT-PCR and droplet-based dPCR equipment was performed to verify the HRM analysis-based methylation detection efficiency of the LOAA digital PCR equipment. Here, sodium bisulfite modification method was applied to detect methylated DNA sequences by each PCR method. RESULTS: Melting curve analysis detected four different Tm values using LOAA and qPCR, and found that LOAA, unlike qPCR, successfully distinguished between different Tm values when the Tm values were very similar. In addition, melting temperatures increased by each methylation were about 0.5℃ for qPCR and about 0.2 ~ 0.6℃ for LOAA. The melting temperature analyses of methylated and unmethylated DNA samples were conducted using LOAA dPCR with TaqMan probes and EvaGreen, and the result found that Tm values of methylated DNA samples are higher than those of unmethylated DNA samples. CONCLUSION: The present study shows that LOAA dPCR could detect different melting temperatures according to methylation status of target sequences, indicating that LOAA dPCR would be useful for diagnostic applications that require the accurate quantification and assessment of DNA methylation.

Accurate and affordable detection of rifampicin and isoniazid resistance in Tuberculosis sputum specimens by multiplex PCR-multiple probes melting analysis.

BACKGROUND: Escalating cases of multidrug-resistant tuberculosis (MDR-TB) pose a major challenge to global TB control efforts, necessitating innovative diagnostics to empower decentralized detection of gene mutations associated with resistance to rifampicin (RIF) and isoniazid (INH) in Mycobacterium tuberculosis (M. tuberculosis) in resource-constrained settings. METHODS: Combining multiplex fluorescent PCR and Multiple Probes Melting Analysis, we identified mutations in the rpoB, katG, ahpC and inhA genes from sputum specimens. We first constructed a reference plasmid library comprising 40 prevalent mutations in the target genes' resistance determining regions and promoters, serving as positive controls. Our assay utilizes a four-tube asymmetric PCR method with specifically designed molecular beacon probes, enabling simultaneous detection of all 40 mutations. We evaluated the assay's effectiveness using DNA isolated from 50 clinically confirmed M. tuberculosis sputum specimens, comparing our results with those obtained from Sanger sequencing and retrospective validation involving bacteriological culture and phenotypic drug susceptibility testing (pDST). We also included the commercial Xpert MTB/RIF assay for accuracy comparison. RESULTS: Our data demonstrated remarkable sensitivity in detecting resistance to RIF and INH, achieving values of 93.33% and 95.24%, respectively, with a specificity of 100%. The concordance between our assay and pDST was 98.00%. Furthermore, the accuracy of our assay was comparable to both Sanger sequencing and the Xpert assay. Importantly, our assay boasts a 4.2-h turnaround time and costs only $10 per test, making it an optimal choice for peripheral healthcare settings. CONCLUSION: These findings highlight our assay's potential as a promising tool for rapidly, accurately, and affordably detecting MDR-TB.

Development of self-compatible Chinese cabbage lines of Chiifu through marker-assisted selection.

The continuously refined genome assembly of the Chinese cabbage accession Chiifu is widely recognized as the reference for Brassica rapa. However, the high self-incompatibility of Chiifu limits its broader utilization. In this study, we report the development of self-compatible Chiifu lines through a meticulous marker-assisted selection (MAS) strategy, involving the substitution of the Chiifu allele of MLPK (M-locus protein kinase) with that from the self-compatible Yellow Sarson (YS). A YS-based marker (SC-MLPK) was employed to screen 841 B. rapa accessions, confirming that all eight accessions with the mlpk/mlpk (mm) genotype exhibited self-compatibility. Additionally, we designed 131 High-Resolution Melting (HRM) markers evenly distributed across the B. rapa genome as genomic background selection (GBS) markers to facilitate the introgression of self-compatibility from YS into Chiifu along with SC-MLPK. Genome background screening revealed that the BC3S1 population had a proportion of the recurrent parent genome (PR) ranging from 93.9% to 98.5%. From this population, we identified self-compatible individuals exhibiting a high number of pollen tubes penetrating stigmas (NPT) (>25) and a maximum compatibility index (CI) value of 7.5. Furthermore, we selected two individuals demonstrating significant similarity to Chiifu in both genetic background and morphological appearance, alongside self-compatibility. These selected individuals were self-pollinated to generate two novel lines designated as SC-Chiifu Lines. The development of these self-compatible Chiifu lines, together with the SC-MLPK marker and the set of HRM markers, represents valuable tools for B. rapa genetics and breeding.

Fabrication and characterization of cocoa butter-based caffeine fast-melting tablets.

Aim: The objective of this study was to develop and characterize the physical properties of fast-melting tablets (FMTs) using cocoa butter as the base and caffeine as the model drug. Method: The simple refrigerator freezing method was employed to prepare caffeine-loaded, FMTs from cocoa butter bases. Results: The F3 chosen formulation achieved a disintegration time of 1.20 min ± 0.035, which falls within the specified limit set by the European Pharmacopoeia. The cumulative drug release data of F3, was 88.52 and 94.08% within 60 and 75 min, respectively (NLT 85% as per US FDA requirement). All the other physical test standards for FMTs met the pharmacopeial specifications. Conclusion: Based on the findings, the simple refrigerator freezing method could be used to formulate FMTs.

Patient-friendly natural caffeine-loaded cocoa butter-based fast-melting tablets with rapid disintegration, affordability, safety and biocompatibility are an efficient base for drug delivery.

Designing starch-based fenofibrate formulations using the melting method.

Fenofibrate (FNF) is used to treat hyperlipidemia. However, FNF is a poorly water-soluble drug, and the dosage of commercial products is relatively high at 160 mg in a Lipidil® tablet. Therefore, this study aimed to develop an FNF-solid dispersion (SD) that solubilizes and stabilizes FNF. The melting method that uses the low melting point of FNF was employed. The dissolution percentage of FNF in the optimal formulation (SD2) increased by 1.2-, 1.3-, and 1.3-fold at 5 min compared to that of Lipidil® and increased by 2.0-, 2.1-, and 2.0-fold compared to the pure FNF in pH 1.2 media, distilled water, and pH 6.8 buffer, which included 0.025 M sodium lauryl sulfate, respectively. The SD2 formulation showed a dissolution percentage of nearly 100 % in all dissolution media after 60 min. The physicochemical properties of the SD2 formulation exhibited slight changes in the melting point and crystallinity of FNF. Moreover, the stability of the SD2 formulation was maintained for six months. In particular, it was challenging to secure stability when starch#1500 was excluded from the SD2 formulation. In conclusion, the dissolution percentage of FNF in the SD2 formulation was improved owing to the weak binding force between FNF and the excipients, stability was secured, and favorable results are expected in future animal experiments.

The cooperative migration dynamics of particles correlates to the nature of hexatic-isotropic phase transition in 2D systems of corner-rounded hexagons.

In the two-dimensional (2D) melting transition of colloidal systems, the hexatic-isotropic (H-I) transition can be either first-order or continuous. However, how particle dynamics differs at the single-particle level during these two different melting transitions remains to be disclosed. In this work, by Brownian dynamics (BD) simulations, we have systematically studied the dynamic behavior of corner-rounded hexagons during the H-I transition, for a range of corner-roundness ζ = 0.40 to 0.99 that covers the crossover from the continuous to first-order nature of H-I transition. The results show that hexagons with ζ ≤ 0.5 display a continuous H-I transition, whereas those with ζ ≥ 0.6 demonstrate a first-order H-I transition. Dynamic analysis shows different evolution pathways of the dominant cluster formed by migrating particles, which results in a droplet-like cluster structure for ζ = 0.40 hexagons and a tree-like cluster structure for ζ = 0.99 hexagons. Further investigations on the hopping activities of particles suggest a cooperative origin of migrating clusters. Our work provides a new aspect to understand the dependence of the nature of H-I transition on the roundness of hexagons through particle dynamic behavior.

Achieving Equiaxed Transition and Excellent Mechanical Properties in a Novel Near-ß Titanium Alloy by Regulating the Volume Energy Density of Selective Laser Melting.

This research investigated the relationship between volume energy density and the microstructure, density, and mechanical properties of the Ti-5Al-5Mo-3V-1Cr-1Fe alloy fabricated via the SLM process. The results indicate that an increase in volume energy density can promote a transition from a columnar to an equiaxed grain structure and suppress the anisotropy of mechanical properties. Specifically, at a volume energy density of 83.33 J/mm3, the average aspect ratio of ß grains reached 0.77, accompanied by the formation of numerous nano-precipitated phases. Furthermore, the relative density of the alloy initially increased and then decreased as the volume energy density increased. At a volume energy density of 83.33 J/mm3, the relative density reached 99.6%. It is noteworthy that an increase in volume energy density increases the ß grain size. Consequently, with a volume energy density of 83.33 J/mm3, the alloy exhibited an average grain size of 63.92 µm, demonstrating optimal performance with a yield strength of 1003.06 MPa and an elongation of 18.16%. This is mainly attributable to the fact that an increase in volume energy density enhances thermal convection within the molten pool, leading to alterations in molten pool morphology and a reduction in temperature gradients within the alloy. The reduction in temperature gradients promotes equiaxed grain transformation and grain refinement by increasing constitutive supercooling at the leading edge of the solid-liquid interface. The evolution of molten pool morphology mainly inhibits columnar grain growth and refines grain by changing the grain growth direction. This study provided a straightforward method for inhibiting anisotropy and enhancing mechanical properties.

Analysis of Underwater Melting Process and Leakage Plugging Performance of Phase-Change Materials.

Leakage is a high-incidence disease of embankment dams, and efficiently addressing this disease guarantees the safe operation of dams. Underwater leakage self-priming plugging technology is a new technology that utilizes the melting and solidifying characteristics of phase-change materials and the negative pressure in the leakage entry area to accurately plug the leakage. However, little is yet known about the underwater melting process of phase-change materials and how their characteristics influence the plugging effect. In this study, three kinds of phase-change materials, namely, paraffin, rosin, and stearic acid, were used to conduct underwater leakage self-priming plugging tests, observe and analyze the underwater melting process, and compare the plugging effects. The results showed that the underwater melting process of phase-change materials exhibited different plugging window periods depending on their melting points, specific heat capacities, and mobilities, which were the main factors affecting their plugging effects. In the final plugging stage, paraffin had the best plugging effect, but the material strength was low; rosin had good plugging compactness, but the fluidity performance was poor, and the material effective utilization was low; stearic acid had a low melting point but dispersed easily. Therefore, a blocking material with a suitable blocking window period can be produced by adjusting the material properties accordingly for an improved blocking effect.

Metal 3D-Printed Bioinspired Lattice Elevator Braking Pads for Enhanced Dynamic Friction Performance.

The elevator industry is constantly expanding creating an increased demand for the integration of high technological tools to increase elevator efficiency and safety. Towards this direction, Additive Manufacturing (AM), and especially metal AM, is one of the technologies that could offer numerous competitive advantages in the production of industrial parts, such as integration of complex geometry, high manufacturability of high-strength metal alloys, etc. In this context, the present study has 3D designed, 3D printing manufactured, and evaluated novel bioinspired structures for elevator safety gear friction pads with the aim of enhancing their dynamic friction performance and eliminating the undesired behavior properties observed in conventional pads. Four different friction pads with embedded bioinspired surface lattice structures were formed on the template of the friction surface of the conventional pads and 3D printed by the Selective Laser Melting (SLM) process utilizing tool steel H13 powder as feedstock material. Each safety gear friction pad underwent tribological tests to evaluate its dynamic coefficient of friction (CoF). The results indicated that pads with a high contact surface area, such as those with car-tire-like and extended honeycomb structures, exhibit high CoF of 0.549 and 0.459, respectively. Based on the acquired CoFs, Finite Element Models (FEM) were developed to access the performance of braking pads under realistic operation conditions, highlighting the lower stress concentration for the aforementioned designs. The 3D-printed safety gear friction pads were assembled in an existing emergency progressive safety gear system of KLEEMANN Group, providing sufficient functionality.

Thermophysical Properties of FUNaK (NaF-KF-UF4) Eutectics.

General interest in the deployment of molten salt reactors (MSRs) is growing, while the available data on uranium-containing fuel salt candidates remains scarce. Thermophysical data are one of the key parameters for reactor design and understanding reactor operability. Hence, filling in the gap of the missing data is crucial to allow for the advancement of MSRs. This study provides novel data for two eutectic compositions within the NaF-KF-UF4 ternary system which serve as potential fuel candidates for MSRs. Experimental measurements include their melting point, density, fusion enthalpy, and vapor pressure. Additionally, their boiling point was extrapolated from the vapor pressure data, which were, at the same time, used to determine the enthalpy of vaporization. The obtained thermodynamic values were compared with available data from the literature but also with results from thermochemical equilibrium calculations using the JRCMSD database, finding a good correlation, which thus contributed to database validation. Preliminary thoughts on fluoride salt reactor operability based on the obtained results are discussed in this study.