Electrosynthesis-Induced Pt Skin Effect in Mesoporous Ni-Rich Ni-Pt Thin Films for Hydrogen Evolution Reaction.

A Pt skin effect, i.e., an enrichment of Pt within the first 1-2 nm from the surface, is observed in as-prepared electrodeposited Ni-rich Ni-Pt thin films. This effect, revealed by Rutherford backscattering (RBS), is present for both dense thin films and mesoporous thin films synthesized by micelle-assisted electrodeposition from a chloride-based electrolyte. Due to the Pt skin effect, the Ni-rich thin films show excellent stability at the hydrogen evolution reaction (HER) in acidic media, during which a gradient in the Pt/Ni ratio is established along the thickness of the thin films, while the activity at the HER remains unaffected by this structural change. Further characterization by elastic recoil detection with He ions analysis shows that hydrogen profiles are similar to those of Pt: a surface hydrogen peak coincides with the Pt skin, and a gradient in hydrogen concentration is established during HER in acidic media, together with a considerable uptake in hydrogen. A comparative study shows that in alkaline media, hydrogen evolution has little to no effect on the structural properties of the thin films, even for much longer times of exposure. The mesoporous thin films, in addition to their higher efficiency at HER compared to dense thin films, also show lower internal stress, as determined by Rietveld refinement of grazing incidence X-ray diffraction patterns. The latter also reveal a fully single-phase and nanocrystalline structure for all thin films with varying Ni contents.

Single-Atom Au-Functionalized Mesoporous SnO2 Nanospheres for Ultrasensitive Detection of Listeria monocytogenes Biomarker at Low Temperatures.

Semiconductor metal oxide gas sensors have been proven to be capable of detecting Listeria monocytogenes, one kind of foodborne bacteria, through monitoring the characteristic gaseous metabolic product 3-hydroxy-2-butanone. However, the detection still faces challenges because the sensors need to work at high temperatures and output limited gas sensing performance. The present study focuses on the design of single-atom Au-functionalized mesoporous SnO2 nanospheres for the sensitive detection of ppb-level 3-hydroxy-2-butanone at low temperatures (50 °C). The fabricated sensors exhibit high sensitivity (291.5 ppm-1), excellent selectivity, short response time (10 s), and ultralow detection limit (10 ppb). The gas sensors exhibit exceptional efficacy in distinguishing L. monocytogenes from other bacterial strains (e.g., Escherichia coli). Additionally, wireless detection of 3-hydroxy-2-butanone vapor is successfully achieved through microelectromechanical systems sensors, enabling real-time monitoring of the biomarker 3-hydroxy-2-butanone. The superior sensing performance is ascribed to the mesoporous framework with accessible active Au-O-Sn sites in the uniform sensing layer consisting of single-atom Au-modified mesoporous SnO2 nanospheres, and such a feature facilitates the gas diffusion, adsorption, and catalytic conversion of 3-hydroxy-2-butanone molecules in the sensing layer, resulting in excellent sensing signal output at relatively low temperature that is favorable for developing low-energy-consumption gas sensors.

Xerogel mesoporous materials based on ultrastable Blatter radicals for efficient sorption of nitric oxide.

The reduction of hazardous nitric oxide emissions remains a significant ecological challenge. Despite the variety of possibilities, sorbents able to capture low concentrations of NO from flue gas with high selectivity are still in demand. In this work a new type of mesoporous xerogel material highly loaded with ultrastable Blatter radicals (BTR, >60 % by mass) that act as selective NO sorption sites is developed. Electron Paramagnetic Resonance (EPR) spectroscopy evidences reversible NO sorption in nanometer-scale pores of BTR-based xerogels and indicates the high NO capacity of such radical-rich sorbent. Efficient NO capture from model flue gas mixture is also evidenced in experiments with a fixed bed reactor. Such advanced properties of new materials as selectivity, strong binding with NO and an ability for mild regeneration via thermodesorption promote them for future ecological applications.

Flexible Mesopores in Nanoscrolls: Extraordinarily Large Alteration of Pore Sizes and Their Reversibility.

Flexible porous materials have gained considerable interest for their potential applications in selective absorption and controlled release/storage of specific molecules or compounds. Here, nanoscrolls are proposed as a type of inorganic solids with reversibly flexible mesopores. Nanoscrolls exhibit a rolled-up structure composed of nanosheets with a 1D rod-like morphology, possessing two distinct nanospaces. The first space comprises 1D tubular mesopores located at the center of the rod, while the second space exists in the interlayer regions on the wall of the mesopore, resulting from the layer stacking caused by the scrolling of nanosheets. By replacing the interlayer cations on the nanoscroll walls with other cations, a drastic alteration in the size of the 1D mesopores is observed. For instance, exchanging bulky dodecylammonium cations with small NH4 + cations leads to a substantial change in pore size, with differences ranging from 10 to 20 nm-a notably larger variation compared to previous reports on flexible porous materials. Importantly, the alteration of pore size induced by the exchange reaction is found to be reversible. This reversible alteration in pore size holds promise for applications in host-guest chemistry involving large moieties such as nanoparticles and enzymes.

Collaborative adsorption and photocatalytic degradation of high concentration pharmaceutical pollutants in water using a novel dendritic fibrous nano-silica modified with chitosan and UiO-66.

This study presents a novel hybrid mesoporous material for degrading drug pollutants in water. The hybrid materials, derived from UiO-66 metal-organic framework and chitosan, coated on nano-silica, showed excellent drug adsorption through hydrogen-bonding interactions and efficient photodegradation of antibiotics. The hybrid material's enhanced conductivity and reduced band gap significantly improved pollution reduction by minimising electron-hole recombination. This allows for more efficient charge transport and better light absorption, boosting the material's ability to break down pollutants. Structural and morphological analyses were conducted using various techniques, including scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy, Brunauer-Emmett-Teller analysis, X-ray photoelectron spectroscopy, and thermogravimetric analysis. Optimising the adsorption-photodegradation process involved investigating pH, catalyst dose, and radiation time. Non-linear optimisation revealed an efficiency exceeding 85 % for 400 mg/L tetracycline and doxycycline, the model antibiotics. The optimal parameters for maximal elimination were determined as pH = 4.3, hybrid mesosphere dose = 4.0 mg/mL, and radiation time = 10 min. Kinetic studies favored pseudo-second-order diffusion models over pseudo-first-order models. The hybrid mesosphere showed sustained efficiency after three cycles and performed well in real aqueous samples, removing over 80 % of each antibiotic. This study demonstrates the potential of the hybrid mesoporous material for removing pharmaceutical pollutants in water systems.

2D PtRhPb Mesoporous Nanosheets with Surface-Clean Active Sites for Complete Ethanol Oxidation Electrocatalysis.

The development of active and selective metal electrocatalysts for complete ethanol oxidation reaction (EOR) into desired C1 products is extremely promising for practical application of direct ethanol fuel cells. Despite some encouraging achievements, their activity and selectivity remain unsatisfactory. In this work, it is reported that 2D PtRhPb mesoporous nanosheets (MNSs) with anisotropic structure and surface-clean metal site perform perfectly for complete EOR electrocatalysis in both three-electrode and two-electrode systems. Different to the traditional routes, a selective etching strategy is developed to produce surface-clean mesopores while retaining parent anisotropy quasi-single-crystalline structure without the mesopore-forming surfactants. This method also allows the general synthesis of surface-clean mesoporous metals with other compositions and structures. When being performed for alkaline EOR electrocatalysis, the best PtRhPb MNSs deliver remarkably high activity (7.8 A mg-1) and superior C1 product selectivity (70% of Faradaic efficiency), both of which are much better than reported electrocatalysts. High performance is assigned to multiple structural and compositional synergies that not only stabilized key OHads intermediate by surface-clean mesopores but also separated the chemisorption of two carbons in ethanol by adjacent Pt and Rh sites, which facilitate the oxidation cleavage of stable C─C bond for complete EOR electrocatalysis.

Application of Stemphylium lycopersici Extracts Immobilized on MCM-48type Mesoporous Materials as Biocatalysts for Monoacylglycerol Production.

Monoacylglycerols are eco-friendly and inexpensive emulsifiers with a range of applications. The traditional synthetic route is not eco-friendly, while enzymatic catalysis offers milder reaction conditions and higher selectivity. However, its application still is limited due to the costs. In this context, endophytic fungi can be source to new biocatalysts with enhanced catalytic activity. Based on this perspective, the aim of this study was perform the synthesis of MAG's through transesterification reactions of solketal and different vinyl esters, using crude and immobilized lipolytic extracts from the endophytic fungi Stemphylium lycopersici, isolated from Humiria balsamifera. The reactions were conducted using 100 mg of biocatalyst, 1 mmol of substrates, 9 : 1 n-heptane/acetone, at 40 °C, 200 rpm for 96 h. In the reactions using the ILE and stearate, laureate and decanoate vinyl esters it was possible to obtain the correspondent products with conversion rates of 52-75 %. Also, according to the structure drivers used in MCM-48 synthesis, different morphologies and conversions rates were observed. Employing [C16MI] Cl, [C14MI] Cl and [C4MI] Cl, the 1-lauroyl- glycerol conversion was 36 %, 79 % and 44 %, respectively. This is the first work involving the immobilization of an endophytic fungi and its utilization as a biocatalyst in the production of MAG's.

Mesoporous Metal Sponges Produced by Explosive Decomposition.

The formation of mesoporous gold sponges by explosive decomposition of 'knallgold' (also known as 'fulminating' gold) is studied. Proof-of-principle experiments are conducted and then the phenomena are further investigated using 'toy physics' molecular dynamics simulations. The simulations invoked various ratios of a volatile Lennard-Jones element G and a noble metal element N. In both experiment and simulation the morphology of the resulting sponge is found to depend on the stoichiometry of the starting material. As the mole fraction of G (χG) is increased from 0.5 to close to 1.0 in the simulations, the morphology of the sponges changes from closed to open, with a corresponding increase in the average mean curvature from 0 to +0.12 inverse Lennard-Jones length (L) units. The average Gaussian curvature of the simulated sponges is always negative, with the minimum value of 0.05 L-2 being found for χG≈0.65. In broad agreement with experiment, sponge formation in the simulations is bounded by stoichiometry; no sponges form if χG is <0.52, for χG between 0.52 and 0.70 the sponge is characterized by vermicular cavities whereas classic bicontinuous fibrous sponges form for 0.70<χG<0.85 and, finally, discrete particles result if χG>0.85.

Highly Efficient Separation of Ethanol Amines and Cyanides via Ionic Magnetic Mesoporous Nanomaterials.

Simple and efficient sample pretreatment methods are important for analysis and detection of chemical warfare agents (CWAs) in environmental and biological samples. Despite many commercial materials or reagents that have been already applied in sample preparation, such as SPE columns, few materials with specificity have been utilized for purification or enrichment. In this study, ionic magnetic mesoporous nanomaterials such as poly(4-VB)@M-MSNs (magnetic mesoporous silicon nanoparticles modified by 4-vinyl benzene sulfonic acid) and Co2+@M-MSNs (magnetic mesoporous silicon nanoparticles modified by cobalt ions) with high absorptivity for ethanol amines (EAs, nitrogen mustard degradation products) and cyanide were successfully synthesized. The special nanomaterials were obtained by modification of magnetic mesoporous particles prepared based on co-precipitation using -SO3H and Co2+. The materials were fully characterized in terms of their composition and structure. The results indicated that poly(4-VB)@M-MSNs or Co2+@M-MSNs had an unambiguous core-shell structure with a BET of 341.7 m2·g-1 and a saturation magnetization intensity of 60.66 emu·g-1 which indicated the good thermal stability. Poly(4-VB)@M-MSNs showed selective adsorption for EAs while the Co2+@M-MSNs were for cyanide, respectively. The adsorption capacity quickly reached the adsorption equilibrium within the 90 s. The saturated adsorption amounts were MDEA = 35.83 mg·g-1, EDEA = 35.00 mg·g-1, TEA = 17.90 mg·g-1 and CN-= 31.48 mg·g-1, respectively. Meanwhile, the adsorption capacities could be maintained at 50-70% after three adsorption-desorption cycles. The adsorption isotherms were confirmed as the Langmuir equation and the Freundlich equation, respectively, and the adsorption mechanism was determined by DFT calculation. The adsorbents were applied for enrichment of targets in actual samples, which showed great potential for the verification of chemical weapons and the destruction of toxic chemicals.

Progress in Core-Shell Magnetic Mesoporous Materials for Enriching Post-Translationally Modified Peptides.

Endogenous peptides, particularly those with post-translational modifications, are increasingly being studied as biomarkers for diagnosing various diseases. However, they are weakly ionizable, have a low abundance in biological samples, and may be interfered with by high levels of proteins, peptides, and other macromolecular impurities, resulting in a high limit of detection and insufficient amounts of post-translationally modified peptides in real biological samples to be examined. Therefore, separation and enrichment are necessary before analyzing these biomarkers using mass spectrometry. Mesoporous materials have regular adjustable pores that can eliminate large proteins and impurities, and their large specific surface area can bind more target peptides, but this may result in the partial loss or destruction of target peptides during centrifugal separation. On the other hand, magnetic mesoporous materials can be used to separate the target using an external magnetic field, which improves the separation efficiency and yield. Core-shell magnetic mesoporous materials are widely utilized for peptide separation and enrichment due to their biocompatibility, efficient enrichment capability, and excellent recoverability. This paper provides a review of the latest progress in core-shell magnetic mesoporous materials for enriching glycopeptides and phosphopeptides and compares their enrichment performance with different types of functionalization methods.

Maillard Reaction Inspired Microexplosion toward Fast Synthesis of Two-Dimensional Mesoporous Tin Oxides for Efficient Chemiresistive Gas Sensing.

Two-dimensional (2D) mesoporous transition metal oxides are highly desired in various applications, but their fast and low-cost synthesis remains a great challenge. Herein, a Maillard reaction inspired microexplosion approach is applied to rapidly synthesize ultrathin 2D mesoporous tin oxide (mSnO2). During the microexplosion between granular ammonia nitrate with melanoidin at high temperature, the organic species can be carbonized and expanded rapidly due to the instantaneous release of gases, thus producing ultrathin carbonaceous templates with rich functional groups to effectively anchor SnO2 nanoparticles on the surface. The subsequent removal of carbonaceous templates via calcination in air results in the formation of 2D mSnO2 due to the confinement effect of the templates. Pd nanoparticles are controllably deposited on the surface of 2D mSnO2 via in situ reduction, forming ultrathin 2D Pd/mSnO2 nanocomposites with thicknesses of 6-8 nm. Owing to the unique 2D mesoporous structure with rich oxygen defects and highly exposed metal-metal oxide interfaces, 2D Pd/mSnO2 exhibits excellent sensing performance toward acetone with high sensitivity, a short response time, and good selectivity under low working temperature (100 °C). This fast and convenient microexplosion synthesis strategy opens up the possibility of constructing 2D porous functional materials for various applications including high-performance gas sensors.

Optimization of Cyanocobalamin (Vitamin B12) Sorption onto Mesoporous Superparamagnetic Iron Oxide Nanoparticles.

The techniques used to detect and quantify cyanocobalamin (vitamin B12) vary considerably in terms of detection sensitivity, from the most sensitive, based on radioisotopes and mass spectrometry (MS) with limits of detection (LOD) in fg mL-1, to fluorescence (FL) and surface plasmon resonance (SPR) biosensors with LOD values in the range of a few µg mL-1. For accurate quantification of an analyte present at trace levels in complex biological matrices, a selective separation and enrichment step is required to overcome matrix interferences and ensure sufficient detection sensitivity. In this study, iron oxide magnetic nanoparticles (IONPs) were used for the extraction and initial preconcentration of cyanocobalamin (vitamin B12). In the dependence of the magnetization on the H-field (hysteresis loop), no coercivity and remanence values were found at 300 K, indicating the superparamagnetic properties of the tested IONPs. Perfluorinated acids were used as amphiphilic agents to allow the sorption of cyanocobalamin onto the IONPs. FT-IR/ATR spectroscopy was used to confirm the sorption of cyanocobalamin on the IONPs. The influence of the addition of a homologous series of perfluorinated acids such as trifluoroacetic acid (TFAA), heptafluorobutyric acid (HFBA), and trichloroacetic acid (TCAA) to the extraction mixture was tested considering their type, mass, and time required for effective sorption. The adsorption kinetics and isotherm, described by the Freundlich and Langmuir equations, were analyzed. The maximum adsorption capacity (qm) exceeded 6 mg g-1 and was 8.9 mg g-1 and 7.7 mg g-1 for HFBA and TCAA, respectively, as the most efficient additives. After the desorption process using aqueous KH2PO4 solution, the sample was finally analyzed spectrophotometrically and chromatographically. The IONP-based method was successfully applied for the isolation of cyanocobalamin from human urine samples. The results showed that the developed approach is simple, cheap, accurate, and efficient for the determination of traces of cyanocobalamin in biological matrices.

Histidine-modified pillar[5]arene-functionalized mesoporous silica materials for highly selective enantioseparation.

Chiral enantiomers, especially the enantiomers of chiral drugs often exhibit different pharmacological activity, metabolism and toxicity, thus it is of great research significance to scientifically and reasonably develop single chiral drugs with low toxicity and high efficiency. Among them, high performance liquid chromatographic techniques based on chiral stationary phases (CSPs) has become one of the most attractive methods used to evaluate the enantiomeric purity of single-enantiomers compound of pharmacological relevance. In this work, pillar[5]arene functionalized with L- and D-histidine, respectively, were modified on the surface of mesoporous silica as novel chiral stationary phases called L/DHis-BP5-Sil. Notably, L/D-histidine had the characteristics of low steric hindrance and easy derivatization. Although the π-π interaction of imidazole group was weaker than that of benzene ring, the benzene ring bonding imidazole-conjugated ring in the structure produced better enantioseparation effect. The results showed that L/DHis-BP5-Sil can separate a variety of complex structural enantiomers with excellent reproducibility, thermal stability and separation performance. Hence, the unique advantage of the highly selective separation of L/DHis-BP5-Sil provides new insights into the enantioseparation field.

Engineering surface framework TiO6 single sites for unprecedented deep oxidative desulfurization.

Catalytic oxidative desulfurization (ODS) using titanium silicate catalysts has emerged as an efficient technique for the complete removal of organosulfur compounds from automotive fuels. However, the precise control of highly accessible and stable-framework Ti active sites remains highly challenging. Here we reveal for the first time by using density functional theory calculations that framework hexa-coordinated Ti (TiO6) species of mesoporous titanium silicates are the most active sites for ODS and lead to a lower-energy pathway of ODS. A novel method to achieve highly accessible and homogeneously distributed framework TiO6 active single sites at the mesoporous surface has been developed. Such surface framework TiO6 species exhibit an exceptional ODS performance. A removal of 920 ppm of benzothiophene is achieved at 60°C in 60 min, which is 1.67 times that of the best catalyst reported so far. For bulky molecules such as 4,6-dimethyldibenzothiophene (DMDBT), it takes only 3 min to remove 500 ppm of DMDBT at 60°C with our catalyst, which is five times faster than that with the current best catalyst. Such a catalyst can be easily upscaled and could be used for concrete industrial application in the ODS of bulky organosulfur compounds with minimized energy consumption and high reaction efficiency.

Ordered Mesoporous Ceria and Cerium Gadolinium Oxide Prepared by Vacuum-Assisted Nanocasting.

Four ceria-based mesoporous oxide materials were prepared using a new vacuum impregnation (VI) templating method developed by the authors, namely, vacuum-assisted nanocasting (VAN). Two hard templates (SBA-15 and KIT-6) were employed, and products with compositions CeO2 and Ce0.9Gd0.1O1.9 (CGO) were made with each. The desired fluorite phase and composition were confirmed by powder XRD and EDS. The product structures were characterised by XRD, TEM, gas physisorption and SAXS. All products contained ordered mesoporous material in high yields. The specific surface areas (SSAs) and pore volumes of the products were determined to be high and the pore size and pore spacings related well to the templates from which the materials were synthesised. The TEM studies confirmed that the samples had a 3D pore structure, with this being the negative of the original template. The target materials were not only produced in high yields, but also displayed a porous single-crystal morphology with non-linear lattice planes. The highest SSA values and pore volumes were reported for materials impregnated using the KIT-6 template and with the CGO composition. The results suggest that VAN is an excellent and reproducible method for producing ordered mesoporous cerias and has considerable potential for wider application. All the mesoporous products showed dramatically increased reducibility in TPR experiments compared with a high-SSA nanoparticulate ceria reference. This is very promising for their potential applications in oxidation catalysts and in fuel cell components.

Ultrasmall Inorganic Mesoporous Nanoparticles: Preparation, Functionalization, and Application.

Ultrasmall mesoporous nanoparticles (<50 nm), a unique porous nanomaterial, have been widely studied in many fields in the last decade owing to the abundant advantages, involving rich mesopores, low density, high surface area, numerous reaction sites, large cavity space, ultrasmall size, etc. This paper presents a review of recent advances in the preparation, functionalization, and applications of ultrasmall inorganic mesoporous nanoparticles for the first time. The soft monomicelles-directed method, in contrast to the hard-template and template-free methods, is more flexible in the synthesis of mesoporous nanoparticles. This is because the amphiphilic micelle has tunable functional blocks, controlled molecule masses, configurations and mesostructures. Focus on the soft micelle directing method, monomicelles could be classified into four types, i.e., the Pluronic-type block copolymer monomicelles, laboratory-synthesized amphiphilic block copolymers monomicelles, the single-molecule star-shaped block copolymer monomicelles, and the small-molecule anionic/cationic surfactant monomicelles. This paper also reviews the functionalization of the inner mesopores and the outer surfaces, which includes constructing the yolkshell structures (encapsulated nanoparticles), anchoring the active components packed on the shell and building an asymmetric Janus architecture. Then, several representative applications, involving catalysis, energy storage, and biomedicines are presented. Finally, the prospects and challenges of controlled synthesis and large-scale applications of ultrasmall mesoporous nanoparticles in the future are foreseen.

Mussel-inspired interface deposition strategy for mesoporous metal-phenolic nanospheres with superior antioxidative, photothermal and antibacterial performance.

Metal-phenolic networks (MPNs) have emerged as a versatile and multifunctional platform applied in bioimaging, disease treatment, electrocatalysis, and water purification. The synthesis of MPNs with mesoporous frameworks and ultra-small diameters (<200 nm), crucial for post-modification, cargo loading, and mass transport, remains a formidable challenge. Inspired by mussel chemistry, mesoporous metal-phenolic nanospheres (MMPNs) are facilely prepared by direct deposition of the metal-polyphenol complex on the interface of oil nano-droplets composed of block copolymers/1,3,5-trimethylbenzene followed by a spontaneous template-removal process. Due to the penetrable and stable networks, the oil nano-droplets gradually leak from the networks driven by shear stress during the stirring process. As a result, MMPNs are obtained without additional template removal procedures such as solvent extraction or high-temperature calcination. The materials have a large pore size (∼12.1 nm), uniform spherical morphology with a small particle size (∼99 nm), and a large specific surface area (49.8 m2 g-1). Due to the abundant phenolic hydroxyl groups, the MMPNs show excellent antioxidative property. The MMPNs also have excellent photothermal property, whose photothermal conversion efficiency was 40.9 %. Moreover, the phenolic hydroxyl groups can reduce Ag+ in situ to prepare Ag nanoparticles loaded MMPNs composites, which have excellent inhibition performance of drug-resistant bacteria biofilm.

Micelle-directed self-assembly of single-crystal-like mesoporous stoichiometric oxides for high-performance lithium storage.

Due to their uncontrollable assembly and crystallization process, the synthesis of mesoporous metal oxide single crystals remains a formidable challenge. Herein, we report the synthesis of single-crystal-like mesoporous Li2TiSiO5 by using soft micelles as templates. The key lies in the atomic-scale self-assembly and step-crystallization processes, which ensure the formation of single-crystal-like mesoporous Li2TiSiO5 microparticles via an oriented attachment growth mechanism under the confinement of an in-situ formed carbon matrix. The mesoporous Li2TiSiO5 anode achieves a superior rate capability (148 mAh g-1 at 5.0 A g-1) and outstanding long-term cycling stability (138 mAh g-1 after 3000 cycles at 2.0 A g-1) for lithium storage as a result of the ultrafast Li+ diffusion caused by penetrating mesochannels and nanosized crystal frameworks (5-10 nm). In comparison, bulk Li2TiSiO5 exhibits poor rate capability and cycle performance due to micron-scale diffusion lengths. This method is very simple and reproducible, heralding a new way of designing and synthesizing mesoporous single crystals with controllable frameworks and chemical functionalities.

Comparative study on Al-SBA-15 prepared by spray drying and traditional methods for bulky hydrocarbon cracking: Properties, performance and influencing factors.

Mesoporous aluminosilicates Al-SBA-15 with large pore sizes and suitable acid properties are promising substitutes to zeolites for catalytic cracking of bulky hydrocarbons without molecular diffusion limitation. The conventional processes to synthesize Al-SBA-15 are time-consuming and often suffer from low "framework" Al contents. Herein, Al-SBA-15 microspheres are synthesized using the rapid and scalable microfluidic jet spray drying technique. They possess uniform particle sizes (45-60 µm), variable surface morphologies, high surface areas (264-340 m2/g), uniform mesopores (3.8-4.9 nm) and rich acid sites (126-812 µmol/g) and high acid strength. Their physicochemical properties are compared with the counterparts synthesized using traditional hydrothermal and evaporation-induced self-assembly methods. The spray drying technique results in a higher incorporation of aluminum (Al) atoms into the silica "framework" compared to the other two methods. The catalytic cracking efficiencies of 1,3,5-triisopropylbenzene (TIPB) on the Al-SBA-15 materials synthesized using the three different methods and nanosized ZSM-5 are compared. The optimal spray-dried Al-SBA-15 exhibits the best performance with 100 % TIPB conversion, excellent selectivity (about 75 %) towards the formation of deeply cracked products (benzene and propylene) and high stability. The catalytic performances of the spray-dried Al-SBA-15 with varying Si/Al ratios are also compared. The reasons for the different performances of the different materials are discussed, where the mesopores, high acid density and strength are observed to play the most critical role. This work might provide a basis for the synthesis of mesoporous rich metal-substituted silica materials for different catalytic applications.

Bottom-Up Construction of Mesoporous Cerium-Doped Titania with Stably Dispersed Pt Nanocluster for Efficient Hydrogen Evolution.

Hydrogen generation is one of the crucial technologies to realize sustainable energy development, and the design of advanced catalysts with efficient interfacial sites and fast mass transfer is significant for hydrogen evolution. Herein, an in situ coassembly strategy was proposed to engineer a cerium-doped ordered mesoporous titanium oxide (mpCe/TiO2), of which the abundant oxygen vacancies (Ov) and highly exposed active pore walls contribute to good stability of ultrasmall Pt nanoclusters (NCs, ∼ 1.0 nm in diameter) anchored in the uniform mesopores (ca. 20 nm). Consequently, the tailored mpCe/TiO2 with 0.5 mol % Ce-doping-supported Pt NCs (Pt-mpCe/TiO2-0.5) exhibits superior H2 evolution performance toward the water-gas shift reaction with a 0.73 molH2·s-1·molPt-1 H2 evolution rate at 200 °C, which is almost 6-fold higher than the Pt-mpTiO2 (0.13 molH2·s-1·molPt-1 H2). Density functional theory calculations confirm that the structure of Ce-doped TiO2 with Ce coordinated to six O atoms by substituting Ti atoms is thermodynamically favorable without the deformation of Ti-O bonds. The Ov generated by the six O atom-coordinated Ce doping is highly active for H2O dissociation with an energy barrier of 2.18 eV, which is obviously lower than the 2.37 eV for the control TiO2. In comparison with TiO2, the resultant Ce/TiO2 support acts as a superior electron acceptor for Pt NCs and causes electron deficiency at the Pt/support interface with a 0.17 eV downshift of the Pt d-band center, showing extremely obvious electronic metal-support interaction (EMSI). As a result, abundant and hyperactive Ti3+-Ov(-Ce3+)-Ptδ+ interfacial sites are formed to significantly promote the generation of CO2 and H2 evolution. In addition, the stronger EMSI between Pt NCs and mpCe/TiO2-0.5 than that between Pt and mpTiO2 contributes to the superior self-enhanced catalytic performance during the cyclic test, where the CO conversion at 200 °C increases from 72% for the fresh catalyst to 99% for the used one. These findings reveal the subtle relationship between the mesoporous metal oxide-metal composite catalysts with unique chemical microenvironments and their catalytic performance, which is expected to inspire the design of efficient heterogeneous catalysts.