Impact of atmospheric conditions on the flash-over voltage of the transmission line insulators using central composite design.

The insulators of overhead power lines play a crucial role in maintaining the reliability of transmission and distribution networks. Because they are exposed to harsh and dynamic environmental conditions, it is essential to investigate the impact of environmental parameters such as pollution, inclined angle with the cross arm, and temperature on the dielectric performance of the insulators of overhead lines. Conventionally, the effect of such parameters can be investigated through experimental measurements of the insulator flashover voltage. However, this approach is costly and time-consuming and calls for the isolation of the lines to conduct the test, causing interruption to the entire grid. As such, there is an essential need to develop a new methodology to quantify the flashover voltage of overhead insulators operating under various environmental conditions, which is the main aim of this paper. The Central Composite Design is employed to develop a mathematical correlation between the insulator flash over voltage as a dependent variable and three environmental parameters: pollution level, inclined angle, and temperature as independent variables. The robustness of the developed equation is validated through extensive experimental measurements of the insulator's flash overvoltage under various conditions. Results reveal a good agreement between the actual and predicted flashover voltage using the developed correlation, as the absolute error for all investigated samples is less than 6%.

Long-term management practices successfully reduce bird-related electrical faults in a transmission grid increasingly used by white storks for nesting.

Bird nests on transmission lines can cause electrical faults which reduce service reliability. To address this problem, since the mid-90s, the Portuguese Transmission System Operator (TSO) has undertaken management actions to discourage white storks Ciconia ciconia from nesting in hazardous locations of the pylons. Here, we compiled and analyzed an 18-year series of data on electrical faults, TSO management actions to tackle these, and stork nests on transmission pylons in Portugal to: (a) determine the relative importance of bird-related faults over the total number of faults; (b) describe variations in bird-related faults across time (season of the year and time of the day); (c) describe spatial variations in bird-related faults and their association with the occurrence of white stork nests on pylons; and (d) analyze the trends, over the years, of the number of white stork nests on pylons, the TSO management actions and their effectiveness in reducing bird-related fault rates. Overall, birds accounted, on average, for 25.3% of the electrical faults in the transmission network, with the vast majority being attributed to white storks. The seasonal pattern of bird-related faults showed higher rates in April and in October-November. Faults occurred more often during the night period, when storks spend more time on the pylons. We found a positive spatial relationship between the electrical fault rate and the proportion of pylons with stork nests (and the correlated number of nests per 100 km of line). There was, however, considerable variation in the fault rates not explained by the stork nest variables, particularly during the non-breeding season. The TSO management actions (namely removal/translocation of nests in hazardous locations of the pylons, installation of anti-perching devices and provision of alternative nesting platforms) significantly reduced, as a whole, the annual number of bird-related faults between 2001 and 2018, despite the three-fold increase in the number of white stork nests on transmission pylons. A deeper understanding of how white storks use the transmission pylons outside the breeding season is needed, so that targeted management actions can be taken to reduce the remaining bird-related fault rates to residual levels.

Proposal for the Integration of the Assessment and Management of Electrical Risk from Overhead Power Lines in BIM for Road Projects.

Electrical risk has a particular impact within the construction sector. This leads to the development of regulations to mitigate it, but correct application of regulations is impossible with a traditional 2D analysis. The construction sector is using technologies from the industrial sector (Construction 4.0), with BIM as the main enabling technology. Thus, the objective of this article is the evaluation of the risk produced by Overhead Power Lines (OPL) through BIM integration. The OPL, its risk zones, the affected road, and the envelope resulting from the geometry of the necessary machines to build it were digitized, converging in a single model to perform a 4D risk analysis. The risks of the execution of the embankment and road surface of a road section passing through an OPL were analyzed by means of the collision of the envelope with its risk zones, resulting in an integration of their evaluation, to which was added the introduction of preventive measures and their re-evaluation. The parametric 3D modelling allowed a better definition of the risk zones and the BIM management minimized errors, providing traceability of decisions from the design phase, complying with health and safety regulations and applying the principle of Prevention through Design (PtD).

3D GIS for surface modelling of magnetic fields generated by overhead power lines and their validation in a complex urban area.

Residential exposure to magnetic fields generated by overhead high-voltage power lines, continues to be a matter of social concern and, for the scientific community, a challenge to model this exposure accurately enough to reliably detect even small effects in large populations complexes. In any expression of the magnetic field intensity, the source-receiver distance is a determining variable, especially in an environment closer to the electrical installation and critical with the existence of significant unevenness in the terrain. However, MF exposure studies adopt, due to their complexity, simplifications of reality where even sometimes the terrain relief and the buckling of the line are not considered. The application of 3D techniques with Geographic Information Systems (GIS) allows us to address this problem. This article presents a model for generating magnetic field intensity surfaces from high-precision terrain elevation data. The series expansion of the Biot-Savart law to an infinite rectilinear conductor with variable height according to the catenary described by the cables using ArcGIS software is applied to calculate the magnetic field. For the validation, 69 control points (1035 field measurements) were used in a free urban area and another 28 points (420 field measurements) in a built-up urban area with complex relief. Good estimates were obtained, although with differences in both areas. With MAPE 9.65% and 19.51%, R2 = 0.922 and 0.949, RMSE = 0.154 and 0.094 µT, respectively. Furthermore, 86% of the points were correctly classified according to usual exposure percentiles. However, the use of a 5 m resolution digital terrain model to obtain high-precision elevation data was an indispensable condition for the good performance of our model. The result as a continuous surface of magnetic field values at the real elevation of the ground can contribute significantly to the development of new environmental and public health studies.

Atmospheric Sensors and Energy Harvesters on Overhead Power Lines.

We demonstrate the feasibility of using novel, small energy harvesters to power atmospheric sensors and radios simply attached to a single conductor of existing overhead power distribution lines. We demonstrate the ability to harvest the required power for operating multiple atmospheric and power-system sensors, together with short-range radios that could broadcast atmospheric sensor data to the cellphones of people nearby. Occasional long-range broadcasts of the data could also be made of both atmospheric and power-line conditions.