RESUMO
BACKGROUND: 3D printers have gained prominence in rapid prototyping and viable in creating dimensionally accurate objects that are both safe within a Magnetic Resonance Imaging (MRI) environment and visible in MRI scans. A challenge when making MRI-visible objects using 3D printing is that hard plastics are invisible in standard MRI scans, while fluids are not. So typically, a hollow object will be printed and filled with a liquid that will be visible in MRI scans. This poses an engineering challenge however since objects created using traditional Fused Deposition Modeling (FDM) 3D-printing techniques are prone to leakage. Digital Light Processing (DLP) is a relatively modern and affordable 3D-printing technique using UV-hardened resin, capable of creating objects that are inherently liquid-tight. When printing hollow parts using DLP printers, one typically requires adding drainage holes for uncured liquid resin to escape during the printing process. If this is not done liquid resin will remain inside the object, which in our application is the desired outcome. PURPOSE: We devised a method to produce an inherently MRI-visible accessory using DLP technology with low dimensional tolerance to facilitate MRI-guided breast biopsies. METHODS: By hollowing out the object without adding drainage holes and tuning printing parameters such as z-lift distance to retain as much uncured liquid resin inside as possible through surface tension, objects that are inherently visible in MRI scans can be created without further post-processing treatment. RESULTS: Objects created through our method are simple and inexpensive to recreate, have minimal manufacturing steps, and are shown to be dimensionally exact and inherently MRI visible to be directly used in various applications without further treatment. CONCLUSION: Our proposed method of manufacturing objects that are inherently both MRI safe, and MRI visible. The proposed process is simple and does not require additional materials and tools beyond a DLP 3D-printer. With only an inexpensive DLP 3D-printer kit and basic cleaning and sanitation materials found in the hospital, we have demonstrated the viability of our process by successfully creating an object containing fine structures with low spatial tolerances used for MRI-guided breast biopsies.
RESUMO
The advent of wearable sensing platforms capable of continuously monitoring physiological parameters indicative of health status have resulted in a paradigm shift for clinical medicine. The accessibility and adaptability of such portable, unobtrusive devices enables proactive, personalized care based on real-time physiological insights. While wearable sensing platforms exhibit powerful capabilities for continuously monitoring physiological parameters, device fabrication often requires specialized facilities and technical expertise, restricting deployment opportunities and innovation potential. The recent emergence of rapid prototyping approaches to sensor fabrication, such as laser-induced graphene (LIG), provides a pathway for circumventing these barriers through low-cost, scalable fabrication. However, inherent limitations in laser processing restrict the spatial resolution of LIG-based flexible electronic devices to the minimum laser spot size. For a CO2 laser-a commonly reported laser for device production-this corresponds to a feature size of â¼120 µm. Here, we demonstrate a facile, low-cost stencil-masking technique to reduce the minimum resolvable feature size of a LIG-based device from 120 ± 20 µm to 45 ± 3 µm when fabricated by CO2 laser. Characterization of device performance reveals this stencil-masked LIG (s-LIG) method yields a concomitant improvement in electrical properties, which we hypothesize is the result of changes in macrostructure of the patterned LIG. We showcase the performance of this fabrication method via production of common sensors including temperature and multi-electrode electrochemical sensors. We fabricate fine-line microarray electrodes not typically achievable via native CO2 laser processing, demonstrating the potential of the expanded design capabilities. Comparing microarray sensors made with and without the stencil to traditional macro LIG electrodes reveals the s-LIG sensors have significantly reduced capacitance for similar electroactive surface areas. Beyond improving sensor performance, the increased resolution enabled by this metal stencil technique expands capabilities for scalable fabrication of high-performance wearable sensors in low-resource settings without reliance on traditional fabrication pathways.
RESUMO
Perfusion of porous scaffolds transports cells to the surface to yield cellular constructs for 3D models of disease and for tissue engineering applications. While ceramic scaffolds mimic the structure and composition of trabecular bone, their opacity and tortuous pores limit the penetration of light into the interior. Scaffolds that are both perfusable and amenable to fluorescence microscopy are therefore needed to visualize the spatiotemporal dynamics of cells in the bone microenvironment. In this study, a hybrid injection molding approach was designed to enable rapid prototyping of collector arrays with variable configurations that are amenable to longitudinal imaging of attached human mesenchymal stem cells (hMSCs) using fluorescence microscopy. Cylindrical collectors were arranged in an array that is permeable to perfusion in the xy-plane and to light in the z-direction for imaging from below. The effects of the collector radius, number, and spacing on the collection efficiency of perfused hMSCs was simulated using computational fluid dynamics (CFD) and measured experimentally using fluorescence microscopy. The effect of collector diameter on simulated and experimental cell collection efficiencies followed a trend similar to that predicted by interception theory corrected for intermolecular and hydrodynamic forces for the arrays with constant collector spacing. In contrast, arrays designed with constant collector number yielded collection efficiencies that poorly fit the trend with collector radius predicted by interception theory. CFD simulations of collection efficiency agreed with experimental measurements within a factor of two. These findings highlight the utility of CFD simulations and hybrid injection molding for rapid prototyping of collector arrays to optimize the longitudinal imaging of cells without the need for expensive and time-consuming tooling.
RESUMO
Microphysiological systems (MPSs) reconstitute tissue interfaces and organ functions, presenting a promising alternative to animal models in drug development. However, traditional materials like polydimethylsiloxane (PDMS) often interfere by absorbing hydrophobic molecules, affecting drug testing accuracy. Additive manufacturing, including 3D bioprinting, offers viable solutions. GlioFlow3D, a novel microfluidic platform combining extrusion bioprinting and stereolithography (SLA) is introduced. GlioFlow3D integrates primary human cells and glioblastoma (GBM) lines in hydrogel-based microchannels mimicking vasculature, within an SLA resin framework using cost-effective materials. The study introduces a robust protocol to mitigate SLA resin cytotoxicity. Compared to PDMS, GlioFlow3D demonstrated lower small molecule absorption, which is relevant for accurate testing of small molecules like Temozolomide (TMZ). Computational modeling is used to optimize a pumpless setup simulating interstitial fluid flow dynamics in tissues. Co-culturing GBM with brain endothelial cells in GlioFlow3D showed enhanced CD133 expression and TMZ resistance near vascular interfaces, highlighting spatial drug resistance mechanisms. This PDMS-free platform promises advanced drug testing, improving preclinical research and personalized therapy by elucidating complex GBM drug resistance mechanisms influenced by the tissue microenvironment.
RESUMO
The limited physical and mechanical properties of polymethyl methacrylate (PMMA), the current gold standard, necessitates exploring improved denture base materials. While three-dimensional (3D) printing offers accuracy, efficiency, and patient comfort advantages, achieving superior mechanics in 3D-printed denture resins remains challenging despite good biocompatibility and esthetics. This review investigates the potential of innovative materials to address the limitations of 3D-printed denture base materials. Thus, this article is organized to provide a comprehensive overview of recent efforts to enhance 3D-printed denture base materials, highlighting advancements. It critically examines the impact of incorporating various nanoparticles (zirconia, titania, etc.) on these materials' physical and mechanical properties. Additionally, it delves into recent strategies for nanofiller surface treatment and biocompatibility evaluation and explores potential future directions for polymeric composites in denture applications. The review finds that adding nanoparticles significantly improves performance compared to unmodified resins, and properties can be extensively enhanced through specific modifications, particularly silanized nanoparticles. Optimizing 3D-printed denture acrylics requires a multifaceted approach, with future research prioritizing novel nanomaterials and surface modification techniques for a novel generation of superior performance, esthetically pleasing, and long-lasting dentures.
Assuntos
Bases de Dentadura , Impressão Tridimensional , Humanos , Nanopartículas/química , Materiais Biocompatíveis/química , Polimetil Metacrilato/química , Materiais Dentários/química , Resinas Acrílicas/química , Propriedades de SuperfícieRESUMO
Facing the rapid development of 6G communication, long-wave infrared metasurface and biomimetic microfluidics, the performance requirements for microsystems based on metal tiny structures are gradually increasing. As one of powerful methods for fabrication metal complex microstructures, localized electrochemical deposition microadditive manufacturing technology can fabricate copper metal micro overhanging structures without masks and supporting materials. In this study, the role of the microprobe cantilever (MC) in localized electrodeposition was studied. The MC can be used for precise deposition with electrolyte localized transport function and high accuracy force-displacement sensitivity. To prove this, the electrolyte flow was simulated when the MC was in bending or normal state. The simulation results can indicate the influence of turbulent flow on the electrolyte flow velocity and the pressure at the end of the pyramid. The results show that the internal flow velocity increased by 8.9% in the bending probe as compared with normal. Besides, this study analyzed the force-potential sensitivity characteristics of the MC. Using the deformation of the MC as an intermediate variable, the model of the probe tip displacement caused by the growth of the deposit and the voltage value displayed by the photodetector was mathematically established. In addition, the deposition of a single voxel was simulated by simulation process with the simulated height of 520 nm for one voxel, and the coincidence of simulation and experimental results was 93.1%. In conclusion, this method provides a new way for localized electrodeposition of complex microstructures.
RESUMO
Proper customization in size and shape is essential in implantable bioelectronics for stable bio-signal recording. Over the past decades, many researchers have heavily relied on conventional photolithography processes to fabricate implantable bioelectronics. Therefore, they could not avoid the critical limitation of high cost and complex processing steps to optimize bioelectronic devices for target organs with various sizes and shapes. Here, we propose rapid prototyping using all laser processes to fabricate customized bioelectronics. PEDOT:PSS is selectively irradiated by an ultraviolet (UV) pulse laser to form wet-stable conductive hydrogels that can softly interact with biological tissues (50 µm line width). The encapsulation layer is selectively patterned using the same laser source by UV-curing polymer networks (110 µm line width). For high stretchability (over 100%), mesh structures are made by the selective laser cutting process. Our rapid prototyping strategy minimizes the use of high-cost equipment, using only a single UV laser source to process the electrodes, encapsulation, and substrates that constitute bioelectronics without a photomask, enabling the prototyping stretchable microelectrode array with an area of 1 cm2 less than 10 min. We fabricated an optimized stretchable microelectrode array with low impedances (â¼1.1 kΩ at 1 kHz) that can effectively record rat's cardiac signals with various health states.
Assuntos
Técnicas Biossensoriais , Condutividade Elétrica , Hidrogéis , Lasers , Hidrogéis/química , Animais , Técnicas Biossensoriais/instrumentação , Ratos , Polímeros/química , Desenho de Equipamento , Poliestirenos/química , TiofenosRESUMO
(1) Background: Various 3D printers are available for dental practice; however, a comprehensive accuracy evaluation method to effectively guide practitioners is lacking. This in vitro study aimed to propose an optimized method to evaluate the spatial trueness of a 3D-printed dental model made of photopolymer resin based on a special structurized dental model, and provide the preliminary evaluation results of six 3D printers. (2) Methods: A structurized dental model comprising several geometrical configurations was designed based on dental crown and arch measurement data reported in previous studies. Ninety-six feature sizes can be directly measured on this original model with minimized manual measurement errors. Six types of photo-curing 3D printers, including Objet30 Pro using the Polyjet technique, Projet 3510 HD Plus using the Multijet technique, Perfactory DDP and DLP 800d using the DLP technique, Form2 and Form3 using the SLA technique, and each printer's respective 3D-printable dental model materials, were used to fabricate one set of physical models each. Regarding the feature sizes of the simulated dental crowns and dental arches, linear measurements were recorded. The scanned digital models were compared with the design data, and 3D form errors (including overall 3D deviation; flatness, parallelism, and perpendicularity errors) were measured. (3) Results: The lowest overall 3D deviation, flatness, parallelism, and perpendicularity errors were noted for the models printed using the Objet30 Pro (overall value: 45 µm), Form3 (0.061 ± 0.019 mm), Objet30 Pro (0.138 ± 0.068°), and Projet 3510 HD Plus (0.095 ± 0.070°), respectively. In color difference maps, different deformation patterns were observed in the printed models. The feature size proved most accurate for the Objet30 Pro fabricated models (occlusal plane error: 0.02 ± 0.36%, occlusogingival direction error: -0.06 ± 0.09%). (4) Conclusions: The authors investigated a novel evaluation approach for the spatial trueness of a 3D-printed dental model made of photopolymer resin based on a structurized dental model. This method can objectively and comprehensively evaluate the spatial trueness of 3D-printed dental models and has a good repeatability and generalizability.
RESUMO
In this paper, electroless nickel plating is explored for the protection of binder-jetting-based additively manufactured (AM) composite materials. Electroless nickel plating was attempted on binder-jetted composites composed of stainless steel and bronze, resulting in differences in the physicochemical properties. We investigated the impact of surface finishing, plating solution chemistry, and plating parameters to attain a wide range of surface morphologies and roughness levels. We employed the Keyence microscope to quantitatively evaluate dramatically different surface properties before and after the coating of AM composites. Scanning electron microscopy revealed a wide range of microstructural properties in relation to each combination of surface finishing and coating parameters. We studied chempolishing, plasma cleaning, and organic cleaning as the surface preparation methods prior to coating. We found that surface preparation dictated the surface roughness. Taguchi statistical analysis was performed to investigate the relative strength of experimental factors and interconnectedness among process parameters to attain optimum coating qualities. The quantitative impacts of phosphorous level, temperature, surface preparation, and time factor on the roughness of the nickel-plated surface were 17.95%, 8.2%, 50.02%, and 13.21%, respectively. On the other hand, the quantitative impacts of phosphorous level, temperature, surface preparation, and time factor on the thickness of nickel plating were 35.12%, 41.40%, 3.87%, and 18.24%, respectively. The optimum combination of the factors' level projected the lowest roughness of Ra at 7.76 µm. The optimum combination of the factors' level projected the maximum achievable thickness of ~149 µm. This paper provides insights into coating process for overcoming the sensitivity of AM composites in hazardous application spaces via robust coating.
RESUMO
Problem: Several types of 3D printers with different techniques and prices are available on the market. However, results in the literature are inconsistent, and there is no comprehensive agreement on the accuracy of 3D printers of different price categories for dental applications. Aim: This study aimed to investigate the accuracy of five different 3D printing systems, including a comparison of budget- and higher-end 3D printing systems, according to a standardized production and evaluation protocol. Material and methods: A maxillary reference model with prepared teeth was created using 16 half-ball markers with a diameter of 1 mm to facilitate measurements. A reference file was fabricated using five different 3D printers. The printed models were scanned and superimposed onto the original standard tesselation language (.stl) file, and digital measurements were performed to assess the 3-dimensional and linear deviations between the reference and test models. Results: After examining the entire surface of the models, we found that 3D printers using Fused filament fabrication (FFF) technology -120.2 (20.3) µm create models with high trueness but high distortion. Distortions along the z-axis were found to be the highest with the stereolithography (SLA)-type 3D printer at -153.7 (38.7) µm. For the 4-unit FPD, we found 201.9 (41.8) µm deviation with the digital light processing (DLP) printer. The largest deviation (-265.1 (55.4) µm) between the second molars was observed for the DLP printer. Between the incisor and the second molar, the best results were produced by the FFF printer with -30.5 (76.7) µm. Conclusion: Budget-friendly 3D printers are comparable to professional-grade printers in terms of precision. In general, the cost of a printing system is not a reliable indicator of its level of accuracy.
RESUMO
Realizing the full potential of plant synthetic biology both to elucidate the relationship between genotype and phenotype and to apply these insights to engineer traits requires rapidly iterating through design-build-test cycles. However, the months-long process of transgenesis, the long generation times, and the size-based limitations on experimentation have stymied progress by limiting the speed and scale of these cycles. Herein, we review a representative sample of recent studies that demonstrate a variety of rapid prototyping technologies that overcome some of these bottlenecks and accelerate progress. However, each of them has caveats that limit their broad utility. Their complementary strengths and weaknesses point to the intriguing possibility that these strategies could be combined in the future to enable rapid and scalable deployment of synthetic biology in plants.
Assuntos
Plantas , Biologia Sintética , Plantas/genéticaRESUMO
The objective of this study was to review the scientific evidence currently available on 3D printable materials and 3D printing technologies used for the fabrication of permanent restorations, focusing on material properties that are clinically relevant. A literature search was performed on four databases (MEDLINE/PubMed, Scopus, Cochrane Library, Web of Science) for articles published from January 2013 until November 2023, using a combination of free words: (restorative dentistry OR prosthetic dentistry) AND (3D printing OR additive manufacturing OR rapid prototyping) AND materials. Two reviewers screened titles and/or abstracts of 2.468 unique studies. In total, 83 studies were selected for full-text reading, from which 36 were included in the review. The assessed variables were mechanical properties, reporting in most of the cases positive results, dimensional accuracy and fit, reporting conflicting results with a predominance of positive, aesthetic properties, with positive reports but scarcely addressed, and biological properties, almost unexplored in independent studies. Despite numerous studies with positive results in favor, papers with negative outcomes were also retrieved. Aesthetic and biological properties are conversely still mostly unexplored. There remains a lack of conclusive evidence for viable 3D printable restorative and prosthodontic materials for permanent restorations. Research should be strengthened by defining international standards for laboratory testing and, where pre-clinical data are promising, conducting clinical trials.
RESUMO
Three-dimensional printing (3DP) is an emerging technology, offering the possibility for the development of dose-customized, effective, and safe solid oral dosage forms (SODFs). Although 3DP has great potential, it does come with certain limitations, and the traditional drug manufacturing platforms remain the industry standard. The consensus appears to be that 3DP technology is expected to benefit personalized medicine the most, but that it is unlikely to replace conventional manufacturing for mass production. The 3DP method, on the other hand, could prove well-suited for producing small batches as an adaptive manufacturing technique for enabling adaptive clinical trial design for early clinical studies. The purpose of this review is to discuss recent advancements in 3DP technologies for SODFs and to focus on the applications for SODFs in the early clinical development stages, including a discussion of current regulatory challenges and quality controls.
Assuntos
Medicina de Precisão , Impressão Tridimensional , Medicina de Precisão/métodos , Indústrias , Controle de Qualidade , Preparações Farmacêuticas , Tecnologia Farmacêutica/métodos , Formas de DosagemRESUMO
BACKGROUND: Proximal humeral fractures (PHFs) are still controversial with regards to treatment and are difficult to classify. The study's objective is to show that preoperative planning performed while handling a three-dimensional (3D) printed anatomical model of the fracture can ensure a better understanding of trauma for both surgeons and patients. MATERIALS AND METHODS: Twenty patients (group A, cases) with complex PHF were evaluated preoperatively by reproducing life-size, full-touch 3D anatomical models. Intraoperative blood loss, radiographic controls, duration of surgery, and clinical outcomes of patients in group A were compared with 20 patients (group B, controls) who underwent standard preoperative evaluation. Additionally, senior surgeons and residents, as well as group A patients, answered a questionnaire to evaluate innovative preoperative planning and patient compliance. Cost analysis was evaluated. RESULTS: Intraoperative radiography controls and length of operation were significantly shorter in group A. There were no differences in clinical outcomes or blood loss. Patients claim a better understanding of the trauma suffered and the proposed treatment. Surgeons assert that the planning of the definitive operation with 3D models has had a good impact. The development of this tool has been well received by the residents. The surgery was reduced in length by 15%, resulting in savings of about EUR 400 for each intervention. CONCLUSIONS: Fewer intraoperative radiography checks, shorter surgeries, and better patient compliance reduce radiation exposure for patients and healthcare staff, enhance surgical outcomes while reducing expenses, and lower the risk of medicolegal claims. LEVEL OF EVIDENCE: Level I, prospective randomized case-control study.
Assuntos
Satisfação do Paciente , Fraturas do Ombro , Humanos , Estudos de Casos e Controles , Duração da Cirurgia , Estudos Prospectivos , Fraturas do Ombro/diagnóstico por imagem , Fraturas do Ombro/cirurgia , Fixação Interna de Fraturas/métodos , Custos e Análise de CustoRESUMO
Bone is a mineralized tissue with the intrinsic capacity for constant remodeling. Rapid prototyping techniques, using biomaterials that mimic the bone native matrix, have been used to develop osteoinductive and osteogenic personalized 3D structures, which can be further combined with drug delivery and phototherapy. Herein, a Fab@Home 3D Plotter printer was used to promote the layer-by-layer deposition of a composite mixture of gelatin, chitosan, tricalcium phosphate, and reduced graphene oxide (rGO). The phototherapeutic potential of the new NIR-responsive 3D_rGO scaffolds was assessed by comparing scaffolds with different rGO concentrations (1, 2, and 4 mg/mL). The data obtained show that the rGO incorporation confers to the scaffolds the capacity to interact with NIR light and induce a hyperthermy effect, with a maximum temperature increase of 16.7 °C after under NIR irradiation (10 min). Also, the increase in the rGO content improved the hydrophilicity and mechanical resistance of the scaffolds, particularly in the 3D_rGO4. Furthermore, the rGO could confer an NIR-triggered antibacterial effect to the 3D scaffolds, without compromising the osteoblasts' proliferation and viability. In general, the obtained data support the development of 3D_rGO for being applied as temporary scaffolds supporting the new bone tissue formation and avoiding the establishment of bacterial infections.
Assuntos
Fosfatos de Cálcio , Quitosana , Grafite , Alicerces Teciduais/química , Quitosana/química , Gelatina/química , Regeneração Óssea , Grafite/farmacologia , Grafite/química , Engenharia Tecidual/métodosRESUMO
With the increased availability of three-dimensional (3D) printers, innovative teaching and training materials have been created in medical fields. For pathology, the use of 3D printing has been largely limited to anatomic representations of disease processes or the development of supplies during the coronavirus disease 2019 pandemic. Herein, an institution's 3D printing laboratory and staff with expertise in additive manufacturing illustrate how this can address design issues in cytopathology specimen collection and processing. The authors' institutional 3D printing laboratory, along with students and trainees, used computer-aided design and 3D printers to iterate on design, create prototypes, and generate final usable materials using additive manufacturing. The program Microsoft Forms was used to solicit qualitative and quantitative feedback. The 3D-printed models were created to assist with cytopreparation, rapid on-site evaluation, and storage of materials in the preanalytical phase of processing. These parts provided better organization of materials for cytology specimen collection and staining, in addition to optimizing storage of specimens with multiple sized containers to optimize patient safety. The apparatus also allowed liquids to be stabilized in transport and removed faster at the time of rapid on-site evaluation. Rectangular boxes were also created to optimally organize all components of a specimen in cytopreparation to simplify and expedite the processes of accessioning and processing, which can minimize errors. These practical applications of 3D printing in the cytopathology laboratory demonstrate the utility of the design and printing process on improving aspects of the workflow in cytopathology laboratories to maximize efficiency, organization, and patient safety.
Assuntos
Laboratórios , Impressão Tridimensional , Humanos , Desenho Assistido por ComputadorRESUMO
INTRODUCTION: At the moment, no commercial model solution is available for the individualisation of the dentition depending on the clinical case scenario. Furthermore, the realistic training of most restorative and prosthodontic procedures on a single dental study model is not possible. The aim of this study was the creation of a new training model to fill this gap. MATERIALS AND METHODS: Complete upper and lower jaw models were created based on existing scans and radiological data from a patient. All components for 100 complete models and 1128 teeth for the training were produced with a SLA-printer. Overall, 94 voluntary students attending the first and second preclinical course in prosthodontics tested the functionality of the model with three different tooth types against a standard dental study model and real teeth. After the training, the model was rated in a questionnaire. RESULTS: The production of the models and teeth was feasible. The overall rating of the different teeth was worse for type I (Ø 3.6 ± 1.1), significantly better for type II (Ø 2.5 ± 1.0) and type III (Ø 2.4 ± 1.0) than a standard typodont tooth (Ø 2.7 ± 1.1). The new model was rated significantly better overall (Ø 2.6 ± 1.0) than the standard training model (Ø 3.0 ± 1.1). CONCLUSIONS: The aim of this study was fulfilled. A superior training model was created with equivalent and better tooth types. The new teeth were outstanding in terms of cost-efficiency, appearance and feeling during preparation.
Assuntos
Coroas , Prostodontia , Humanos , Prostodontia/educação , Educação em Odontologia , Avaliação Educacional , Estudantes de OdontologiaRESUMO
INTRODUCTION: Additive manufacturing is a tool with potential use in medicine and dentistry. The manufacture of metals and composites is already advanced, however, concerns about titanium hypersensitivity, tissue staining, and corrosion caused by gradual material degradation encourage research into more biocompatible alternatives. OBJECTIVE: This systematic scoping review aimed to gather studies that evaluated zirconia implants produced by additive manufacturing to describe the current stage of the printing technique and the final product. METHODS: Searches in Embase, PubMed, SCOPUS, Web of Science, and Google Scholar databases were enriched with manual searches between February and March 2021 and updated in June 2022 using keywords: zirconium implants, zirconium oxide, additive manufacturing, rapid prototyping, 3D printing, selective laser melting, and electron beam melting. The criteria included studies that evaluated or described zirconia implants obtained by 3D printing, with a direct relationship to dentistry or orthopedics. RESULTS: The database search resulted in 671 articles. Eight articles were selected for full reading and remained in this systematic review. CONCLUSION: The printing technique for zirconia implants is promising. However, further studies are required before implants produced by the printing technique can be tested clinically. The literature with results regarding the impression product is still limited.
Assuntos
Implantes Dentários , Zircônio , Impressão Tridimensional , TitânioRESUMO
Maxillofacial reconstructive implants are typically created in standard shapes and have a widespread application in head and neck surgery. During surgical procedures, the implant must be correctly bent according to the architecture of the particular bones. Bending takes practice, especially for untrained surgeons. Furthermore, repeated bending may increase internal stress, resulting in fatigue in vivo under masticatory loading and an array of consequences, including implant failure. There is a risk of fracture, screw loosening, and bone resorption. Resorption, infection, and displacement are usually associated with the use of premade alloplastic implants and autogenous grafts. Recent technological breakthroughs have led to the use of patient-specific implants (PSIs) developed by computer-designed additive manufacturing in reconstructive surgery. The use of computer-designed three-dimensional (3D)-printed PSI allows for more precise restoration of maxillofacial deformities, avoiding the common difficulties associated with premade implants and increasing patient satisfaction. Additive manufacturing is something that refers to a group of additive manufacturing methods. This technique has been quickly used in a variety of surgical procedures. The exponential expansion of this technology can be attributed to its enormous surgical value. Adding 3D printing to a medical practice can be a rewarding experience with stunning results.
RESUMO
Microfluidic organ-on-chip models recapitulate increasingly complex physiological phenomena to study tissue development and disease mechanisms, where there is a growing interest in retrieving delicate biological structures from these devices for downstream analysis. Standard bonding techniques, however, often utilize irreversible sealing, making sample retrieval unfeasible or necessitating destructive methods for disassembly. To address this, several commercial devices employ reversible sealing techniques, though integrating these techniques into early-stage prototyping workflows is often ignored because of the variation and complexity of microfluidic designs. Here, we demonstrate the concerted use of rapid prototyping techniques, including 3D printing and laser cutting, to produce multi-material microfluidic devices that can be reversibly sealed. This is enhanced via the incorporation of acrylic components directly into polydimethylsiloxane channel layers to enhance stability, sealing, and handling. These acrylic components act as a rigid surface separating the multiple mechanical seals created between the bottom substrate, the microfluidic features in the device, and the fluidic interconnect to external tubing, allowing for greater design flexibility. We demonstrate that these devices can be produced reproducibly outside of a cleanroom environment and that they can withstand ~1 bar pressures that are appropriate for a wide range of biological applications. By presenting an accessible and low-cost method, we hope to enable microfluidic prototyping for a broad range of biomedical research applications.