Recycling Fe and improving organic pollutant removal via in situ forming magnetic core-shell Fe3O4@CaFe-LDH in Fe(II)-catalyzed oxidative wastewater treatment.

Due to its high efficiency, Fe(II)-based catalytic oxidation has been one of the most popular types of technology for treating growing organic pollutants. A lot of chemical Fe sludge along with various refractory pollutants was concomitantly produced, which may cause secondary environmental problems without proper disposal. We here innovatively proposed an effective method of achieving zero Fe sludge, reusing Fe resources (Fe recovery = 100%) and advancing organics removal (final TOC removal > 70%) simultaneously, based on the in situ formation of magnetic Ca-Fe layered double hydroxide (Fe3O4@CaFe-LDH) nano-material. Cations (Ca2+ and Fe3+) concentration (≥ 30 mmol/L) and their molar ratio (Ca:Fe ≥ 1.75) were crucial to the success of the method. Extrinsic nano Fe3O4 was designed to be involved in the Fe(II)-catalytic wastewater treatment process, and was modified by oxidation intermediates/products (especially those with COO- structure), which promoted the co-precipitation of Ca2+ (originated from Ca(OH)2 added after oxidation process) and by-produced Fe3+ cations on its surface to in situ generate core-shell Fe3O4@CaFe-LDH. The oxidation products were further removed during Fe3O4@CaFe-LDH material formation via intercalation and adsorption. This method was applicable to many kinds of organic wastewater, such as bisphenol A, methyl orange, humics, and biogas slurry. The prepared magnetic and hierarchical CaFe-LDH nanocomposite material showed comparable application performance to the recently reported CaFe-LDHs. This work provides a new strategy for efficiently enhancing the efficiency and economy of Fe(II)-catalyzed oxidative wastewater treatment by producing high value-added LDHs materials.

Soil colloids can significantly enhance spreading of polybromodiphenyl ethers in groundwater by serving as an effective carrier.

Polybromodiphenyl ethers (PBDEs), the widely used flame retardants, are common contaminants in surface soils at e-waste recycling sites. The association of PBDEs with soil colloids has been observed, indicating the potential risk to groundwater due to colloid-facilitated transport. However, the extent to which soil colloids may enhance the spreading of PBDEs in groundwater is largely unknown. Herein, we report the co-transport of decabromodiphenyl ester (BDE-209) and soil colloids in saturated porous media. The colloids released from a soil sample collected at an e-waste recycling site in Tianjin, China, contain high concentration of PBDEs, with BDE-209 being the most abundant conger (320 ± 30 mg/kg). The colloids exhibit relatively high mobility in saturated sand columns, under conditions commonly observed in groundwater environments. Notably, under all the tested conditions (i.e., varying flow velocity, pH, ionic species and ionic strength), the mass of eluted BDE-209 correlates linearly with that of eluted soil colloids, even though the mobility of the colloids varies markedly depending on the specific hydrodynamic and solution chemistry conditions involved. Additionally, the mass of BDE-209 retained in the columns also correlates strongly with the mass of retained colloids. Apparently, the PBDEs remain bound to soil colloids during transport in porous media. Findings in this study indicate that soil colloids may significantly promote the transport of PBDEs in groundwater by serving as an effective carrier. This might be the reason why the highly insoluble and adsorptive PBDEs are found in groundwater at some PBDE-contaminated sites.

Safety assessment of the process Lietpak, based on the EREMA MPR technology, used to recycle post-consumer PET into food contact materials.

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Lietpak (EU register number RECYC327), which uses the EREMA MPR technology. The input material is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, including no more than 5% PET from non-food consumer applications. The flakes are heated in a ■■■■■ reactor under vacuum. Having examined the challenge test provided, the Panel concluded that the ■■■■■ decontamination (step 2), for which a challenge test was provided, is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of this step are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 µg/kg food, derived from the exposure scenario for infants, when such recycled PET is used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave or conventional ovens and such uses are not covered by this evaluation.

Growth performance of African catfish (Clarias gariepinus) in aquaponic systems with varying densities of Vietnamese coriander (Persicaria odorata).

Mass cultivation of high-value aromatic herbs such as Vietnamese coriander and Persicaria odorata required specific soil, nutrients, and irrigation, mostly found in the limited natural wetland. This study aimed to evaluate the capacity of P. odorata at different densities in nutrient removal and the growth performance of African catfish, Clarias gariepinus in aquaponic systems. P. odorata was cultivated for 40 d with less than 10% water exchange. The effects of increasing crop densities, from zero plants for the control, 0.035 ± 0.003 kg/m2 in Treatment 1, 0.029 ± 0.002 kg/m2 in Treatment 2, and 0.021 ± 0.003 kg/m2 in Treatment 3, were tested on the growth performance of C. gariepinus with an initial density of 3.00 ± 0.50 kg/m3. The specific growth rate (SGR), daily growth rate of fish (DGRf), and survival rate (SR) of the C. gariepinus were monitored. Nutrient removal, daily growth rate of plant (DGRp), relative growth rate (RGR), and the sum of leaf number (Æ©n) of the P. odorata plant were also recorded. It was found that nutrient removal percentage significantly increased with the presence of P. odorata at different densities. The growth performance of C. gariepinus was also affected by P. odorata density in each treatment. However, no significant difference was observed in the DGRp and RGR of the P. odorata (p>0.05), except for Æ©n values. Treatment 1 had the highest Æ©n number compared to Treatment 2 and Treatment 3, showing a significant difference (p<0.05). This study demonstrates that the presence of P. odorata significantly contributes to lower nutrient concentrations, supporting the fundamental idea that plants improve water quality in aquaponic systems.

Biofilm mitigation in hybrid chemical-biological upcycling of waste polymers.

Introduction: Accumulation of plastic waste in the environment is a serious global issue. To deal with this, there is a need for improved and more efficient methods for plastic waste recycling. One approach is to depolymerize plastic using pyrolysis or chemical deconstruction followed by microbial-upcycling of the monomers into more valuable products. Microbial consortia may be able to increase stability in response to process perturbations and adapt to diverse carbon sources, but may be more likely to form biofilms that foul process equipment, increasing the challenge of harvesting the cell biomass. Methods: To better understand the relationship between bioprocess conditions, biofilm formation, and ecology within the bioreactor, in this study a previously-enriched microbial consortium (LS1_Calumet) was grown on (1) ammonium hydroxide-depolymerized polyethylene terephthalate (PET) monomers and (2) the pyrolysis products of polyethylene (PE) and polypropylene (PP). Bioreactor temperature, pH, agitation speed, and aeration were varied to determine the conditions that led to the highest production of planktonic biomass and minimal formation of biofilm. The community makeup and diversity in the planktonic and biofilm states were evaluated using 16S rRNA gene amplicon sequencing. Results: Results showed that there was very little microbial growth on the liquid product from pyrolysis under all fermentation conditions. When grown on the chemically-deconstructed PET the highest cell density (0.69 g/L) with minimal biofilm formation was produced at 30°C, pH 7, 100 rpm agitation, and 10 sL/hr airflow. Results from 16S rRNAsequencing showed that the planktonic phase had higher observed diversity than the biofilm, and that Rhodococcus, Paracoccus, and Chelatococcus were the most abundant genera for all process conditions. Biofilm formation by Rhodococcus sp. And Paracoccus sp. Isolates was typically lower than the full microbial community and varied based on the carbon source. Discussion: Ultimately, the results indicate that biofilm formation within the bioreactor can be significantly reduced by optimizing process conditions and using pure cultures or a less diverse community, while maintaining high biomass productivity. The results of this study provide insight into methods for upcycling plastic waste and how process conditions can be used to control the formation of biofilm in bioreactors.

Reaction of ß -Ketoester and 1,3-Diol to Access Chemically Recyclable and Mechanically Robust Poly(vinyl alcohol) Thermosets through Incorporation of ß -(1,3-dioxane)ester.

The development of mechanically robust, chemically stable, and yet recyclable polymers represents an essential undertaking in the context of advancing a circular economy for plastics. We introduce a novel cleavable ß-(1,3-dioxane)ester (DXE) linkage, synthesized through the catalyst-free reaction of ß-ketoester and 1,3-diol, to cross-link poly(vinyl alcohol) (PVA) for the formation of high-performance thermosets with inherent chemical recyclability. PVA, modified with ß-ketoester through the transesterification reaction with excess tert-butyl acetoacetate, cross-links with the unmodified 1,3-diols within PVA itself upon thermal treatment. Cross-linking improves PVA's mechanical properties, with Young's modulus and toughness that reach up to 656 MPa and 84 MJ cm-3, i.e. 3- and 12-fold those of linear PVA. Thermal treatment of the cross-linked PVA under acid conditions leads to deconstruction of the networks, allowing the almost PVA excellent recovery (> 90%) . In the absence of thermal or acidic treatment, cross-linked PVA maintains its dimensional stability. We show that the recovery of PVA is also possible when the treatment is performed in the presence of other plastics commonly found in recycling mixtures. Furthermore, PVA-based composites comprising carbon fibers and activated charcoal cross-linked by the DXE linkages are also shown to be recyclable with recovery of the PVA and the fillers.

Aligners: review of their chemical components, recycling, mechanical properties and therapeutic needs - Part 1 / Aligneurs : mise en perspective de la composition chimique, du recyclage, des propriétés mécaniques et des besoins thérapeutiques ­ Partie 1.

Introduction: The aligner is a thermoformed plastic device composed of various chemical components: polyurethane, polyethylene terephthalate glycol, polypropylene… All these plastics must be sufficiently resistant to abrasion and translucent for aesthetic purposes, but their solubility to salivary enzymes, insertion-disinsertion fatigue and recyclability vary according to material. From an orthodontic point of view, they must facilitate tooth movement. However, their behavior differs from that of orthodontic archwires: their Young's modulus, resilience and unloading curve are distinct, resulting in mechanical properties that fall significantly below the orthodontic requirements of multi-bracket systems. Objective: The aim of this article was to review the chemical composition, recycling and mechanical properties of aligners, and to put them into perspective with therapeutic indications. Materials and Methods: Literature data were approximated to orthodontic needs. Results: Neither plastic nor direct printing can match the mechanical properties of our archwires or the procedures of a reliable vestibular multi-attachment appliance. Discussion: Aligners remain an interesting tool in targeted indications.

Introduction: L'aligneur est un dispositif en plastique thermoformé dont la composition chimique est diverse : polyuréthane, polyéthylène téréphtalate glycol, polypropylène… Tous ces plastiques doivent être suffisamment résistants à l'abrasion et translucides pour être esthétiques mais ils présentent une solubilité aux enzymes salivaires, une fatigue liée à l'insertion-désinsertion et une recyclabilité qui sont variables selon le matériau. D'un point de vue orthodontique, ils doivent permettre de déplacer les dents. Mais leur comportement ne ressemble pas à celui des arcs orthodontiques : leur module de Young, leur résilience et leur courbe de décharge en sont éloignés et confèrent des propriétés mécaniques très inférieures aux exigences orthodontiques des appareils multi-attaches. Objectif: L'objectif de l'article était de faire le point sur la composition chimique, le recyclage, les propriétés mécaniques des aligneurs et de les mettre en perspective avec les indications thérapeutiques. Matériel et méthode: Les données de la littérature sont approchées des besoins orthodontiques. Résultats: Ni le plastique, ni l'impression directe ne sont en capacité de rivaliser avec les propriétés mécaniques de nos arcs ou avec les procédures d'un appareil multi-attache vestibulaire fiables. Discussion: Les aligneurs restent un outil intéressant dans des indications ciblées.

Copper leaching from ultrasonically treated milled waste printed circuit boards: investigation of parameters optimization and kinetics.

Waste printed circuit boards (WPCBs) encompass abundant metals (gold, silver, and copper), along with other harmful materials including brominated epoxy resins, plastics, and heavy metals (lead, mercury, and cadmium). Direct burning and landfilling of WPCBs may cause severe health issues and impair the environment. Therefore, sustainable treatment of WPCBs is necessary to recover valuable metals and remove hazardous materials before disposal. The present work investigates the separation of copper-rich metallic fractions from the WPCBs by the combination of hammer milling and ultrasonic irradiation. Initially, discarded mobile phone PCBs are pre-processed and shortened into 1 × 1 cm2. Downscaled WPCBs are fed into the hammer mill to obtain the fine ground powder. The Powdered WPCBs are further processed through ultrasonic treatment to acquire metal-rich fraction. XRD, SEM-EDS, and ICP/AAS analysis revealed that the current technique can efficiently separate the metal-rich fraction without using toxic solvents. Results show the enhancement of copper fraction from 42.73 to 87 wt. % after ultrasonic treatment of WPCBs ground powder. Further, nitric acid leaching has been implemented to metal-rich fractions, and the parameters have been optimized for copper leaching with the assistance of response surface methodology (RSM) of the design of experiments (DOE). Quantitative dissolution (98.96%) of copper occurred using 3.5 M nitric acid within 3 h at 30 °C with 50 GPL pulp density and 500 rpm agitation speed. Finally, the kinetics of the leaching process were studied to conform the kinetics model. Moreover, the activation energy for diffusion (19.075 kJ/mole) and reaction kinetics model (13.29 kJ/mole) has also been calculated. The low energy consumption due to room temperature pre-treatment and effective leaching ensures the industrial feasibility of the proposed process.

Technical Properties and Biological Safety of Reprocessing Technique for a Handpiece of Disposable Pulsatile Lavage Device: An Experimental Study.

Introduction: Bony surface cleaning using a pulse lavage device (PLD) is essential for modern cementation of hip and knee arthroplasties. This costly single-use device is a medical waste and unaffordable for some patients. Reprocessing is a worldwide standard strategy to solve this problem. To determine the technical properties and biological safety of a reprocessed PLD handpiece and compare its performance under different power supplies. Materials and Methods: Eight brand-new disposable PLDs were tested for baseline technical properties (flow rate, pulse frequency, and peak pressure). Thereafter, they were reprocessed and retested for 10 rounds using two different power supplies. An adenosine triphosphate (ATP) swab test was performed on the PLD accessory parts after cleansing and disinfection. Passed-through isotonic sodium chloride solution ejected from the reprocessed PLD underwent aerobic bacterial culture. The unit costs of production were analysed. Results: The mean flow rate of the disposable PLD (1.5±0.1 L/min) was less than that of reprocessed PLD using DC15V battery (2.5±0.3 L/min, p<0.001) and AC/DC15V3A adapter (6.1±0.4 L/min, p<0.001). The mean pulse frequency and peak pressure of the disposable PLD and reprocessed PLD using DC15V battery were not different (18.5±0.8 vs 18.8±2.5 Hz, p=0.155 and 0.37±0.04 vs 0.38±0.03 N/mm2, p=0.640, respectively), but were lower than those using AC/DC15V3A adapter (47.0±2.7 Hz, 0.45±0.03 N/mm2, p<0.001). All ATP swab tests, and aerobic fluid cultures yielded negative results. The total cost of reprocessing was 10% of disposable PLD. Conclusion: A disposable PLD handpiece can be reprocessed without deteriorating its technical properties and used with either retrieved DC15V battery or AC/DC15V3A adapter for the power supply. As the biological safety of reprocessed and disposable PLDs was comparable, it may be clinically utilised with 90% cost reduction.

Uncovering Availability of the Secondary Iron Resources in China: Integrating Material Flow Analysis and Secondary Resources Reserve Assessment.

As the largest iron and steel producer, China still cannot meet its demand of iron and steel only through domestic primary supply in the last few decades. Hence, secondary iron resources are increasingly significant in meeting China's iron supply and demand balance. However, the secondary iron resource availability in China and how it impacts the future supply demand balance were still insufficiently discussed. In this work, we developed a material flow analysis and secondary resources reserve assessment (MFA-SRRA) integrated model, assessed secondary iron resources availability, and conducted a supply demand analysis through nine scenarios for irons in China. The results showed that China's secondary iron reserves will increase from 8.9 Gt in 2021 to 14.04 to 19.01 Gt in 2050. With the increasing secondary iron supply, more than 60% of iron ore as a source of steelmaking can be replaced by 2050. Landfills, as a significant reserve of iron but always ignored, will accumulate 1.42-1.51 Gt secondary iron resources by 2050 and should be noticed to be mined and utilized in the future. Last, we suggest that promoting innovation in landfill mining technology and making sustainable material management policies are urgent to prevent these secondary iron resources from becoming real waste.

Macrophage-mediated myelin recycling fuels brain cancer malignancy.

Tumors growing in metabolically challenged environments, such as glioblastoma in the brain, are particularly reliant on crosstalk with their tumor microenvironment (TME) to satisfy their high energetic needs. To study the intricacies of this metabolic interplay, we interrogated the heterogeneity of the glioblastoma TME using single-cell and multi-omics analyses and identified metabolically rewired tumor-associated macrophage (TAM) subpopulations with pro-tumorigenic properties. These TAM subsets, termed lipid-laden macrophages (LLMs) to reflect their cholesterol accumulation, are epigenetically rewired, display immunosuppressive features, and are enriched in the aggressive mesenchymal glioblastoma subtype. Engulfment of cholesterol-rich myelin debris endows subsets of TAMs to acquire an LLM phenotype. Subsequently, LLMs directly transfer myelin-derived lipids to cancer cells in an LXR/Abca1-dependent manner, thereby fueling the heightened metabolic demands of mesenchymal glioblastoma. Our work provides an in-depth understanding of the immune-metabolic interplay during glioblastoma progression, thereby laying a framework to unveil targetable metabolic vulnerabilities in glioblastoma.

Sustainable repurpose of end-of-life fiber reinforced polymer composites: A new circular pedestrian bridge concept.

In response to global challenges in resource supply, many industries are adopting the principles of the Circular Economy (CE) to improve their resource acquisition strategies. This paper introduces an innovative approach to address the environmental impact of waste Glass Fiber Reinforced-Polymer (GFRP) pipes and panels by repurposing them to manufacture structural components for new bicycle and pedestrian bridges. The study covers the entire process, including conceptualization, analysis, design, and testing of a deck system, with a focus on the manufacturing process for a 7-m-long prototype bridge. The study shows promising results in the concept of a sandwich structure utilizing discarded GFRP pipes and panels, which has the flexibility to account for variabilities in dimensions of incoming products while still meeting mechanical requirements. The LCA analysis shows that the transportation of materials is the governing contributing factor. It was concluded that further development of this concept should be accompanied by a business model that considers the importance of the contributions from the whole value chain.

Comprehensive review of technologies for separate digestate treatment and agricultural valorisation within circular and green economy.

Anaerobic digestion (AD) has the potential to catalyse the shift from a linear to a circular economy. However, effective treatment and management of both solid (DSF) and liquid (DLF) digestate fraction treatment and management require adopting sustainable technologies to recover valuable by-products like energy, biofuels, biochar, and nutrients. This study reviews state-of-the-art advanced technologies for DSF and DLF treatment and valorisation, using life cycle assessment (LCA) and techno-economic analysis (TEA) in integrated digestate management (IDM). Key findings highlight these technologies' potential in mitigating environmental impacts from digestate management, but there's a need to improve process efficiency, especially at larger scales. Future research should prioritize cost-effective and eco-friendly IDM technologies. This review emphasizes how LCA and TEA can guide decision-making and promote sustainable agricultural practices. Ultimately, sustainable IDM technologies can boost resource recovery and advance circular economy principles, enhancing the environmental and economic sustainability of AD processes.

High-Performance Organic Aerogels Tailored for Versatile Recycling Approaches: Recycling-Reforming-Upcycling.

Organic aerogels are emerging as promising materials due to their versatile properties, rendering them excellent candidates for a variety of applications in the fields of thermal insulation, energy storage, pharmaceuticals, chemical adsorption, and catalysis. However, current aerogel designs rely on cross-linked polymer networks, which lack efficient end-of-use solutions, thereby hindering their overall sustainability. In this study, a facile synthesis of organic aerogels with a unique combination of imine and cyanurate moieties is presented, resulting in high-performance, lightweight insulating materials. The aerogels' structure, ensures mechanical robustness, thermal resistance, and hydrophobicity without additional treatments, crucial for long-term performance. Additionally, in response to the currently unsustainable use of cross-linked polymer materials, the molecular design offers diverse avenues of chemical recycling. These include full depolymerization back into the original monomers, partial network fragmentation producing soluble oligomers that can be promptly employed to fabricate new aerogels, and upcycling of aerogel waste into useful building blocks. This work pioneers a novel approach to material design, emphasizing recyclability as a core feature while maintaining high-performance excellence.

Valorization of sewage sludge incineration ash as a novel soilless growing medium for urban agriculture and greenery.

Limited open areas for urban agriculture and greenery have led to the search for innovative, sustainable growing media to strengthen the food supply and improve atmospheric quality for a resilient city. Rampant land developments have caused soil to become increasingly scarce. Sewage sludge incineration ash (SSIA), the by-product of waste-to-energy (WtE) incineration of sewage sludge, is a major municipal waste containing phosphorus-fertilizing nutrients. For the first time, we investigated the novel application of SSIA as a soilless plant-growing medium with built-in fertilizer. SSIA outperformed topsoil in bulk density, water-holding capacity, porosity, and nutrient content. However, it was found that SSIA has a high salinity and should be treated first. Wheatgrass (Triticum aestivum L.), a fast-growing glycophyte, thrived in the desalinated SSIA, showing growth and nutrient content comparable to the topsoil case. Simultaneously, it demonstrated phytoremediation. The SSIA residue was then recycled into cementitious materials, using desalinating water for mixing. SSIA upcycle into a growing medium facilitates urban resource management by utilizing nutrients in sewage waste for eco-friendly plant cultivation, benefiting urban agriculture and greenery. It is also a prudent valorization step before further recycling SSIA to reduce landfill requirements.

Circular Economy of Construction and Demolition Waste for Nanocomposite Cement: XRD, NMR, Vickers, Voltammetric and EIS Characterization.

In this paper, we present the structural, mechanical and electrical properties of composite cement materials that can be widely used as substituent for cement. We start with the characterization of a composite cement sample using an analysis of X-ray diffraction (XRD) and nuclear magnetic resonance (NMR) spectra. The measurements of the Vickers hardness, cyclic and sweep linear voltammetry and electrochemical impedance spectroscopy (EIS) of composite cement materials were also recorded. This study compared the effect of the different nanocomposites added to cement on the mitigation of the alkali-silica reaction, which is responsible for the swelling, cracking and deleterious behavior of the material. The enhancement in Vickers hardness was more pronounced for composite cement materials. In contrast, the values of Vickers hardness decreased for the composite cement containing mortar and the control sample, suggesting that the long-term performance of cement was compromised. In order to obtain information about the bulk resistance of the composite cement material, electrochemical impedance spectroscopy (EIS) data were employed. The results suggest that for composite cement materials, there is an improvement in bulk electrical resistance, which can be attributed to the lower amounts of cracks and swelling due to lower expansion. In the control sample, a reduction in the bulk resistance suggests the formation of microcracks, which cause the aging and degradation of the material. The intersection of arcs in the EIS spectrum of the mixed composite cement sample gradually increased by an alkaline exposure of up to 21 days and finally shifted towards a low value of high frequency with an increase in alkaline exposure of up to 28 days.

Microalgae-derived hydrogels/membranes for phosphorus removal and recovery from aquaculture tailwater: Waste utilization and phosphorus recycling.

Efficient removal and recovery of phosphorus from aquaculture tailwater is challenging due to increasing strict water environment restrictions. This study presents a sustainable approach by using microalgae-waste-derived hydrogels/membranes for phosphorus adsorption and microalgae cultivation. Waste from Euglena gracilis (or Haematococcus pluvialis), modified with magnesium, was converted into biochars (abbreviated as MEBC or MHBC). This biochars were then combined with sodium alginate to fabricate hydrogels and with polyvinyl chloride to create membranes. Due to the almost 100 % phosphorus removal of MEBC (or MHBC) biochar, the as-obtained hydrogels/membranes demonstrated excellent phosphate adsorption, reducing total phosphorus in real aquaculture tailwater from 11 mg/L to 0. Additionally, the phosphorus-saturated hydrogel served as a phosphorus source for microalgae cultivation, while the membranes facilitated microalgae harvesting with a water flux over 40 L/m2/h. This study provides an eco-friendly solution for using microalgae-waste-derived materials to effectively address phosphorus removal and recovery challenges in aquaculture tailwater.

A brief history and future directions of dielectrophoretic filtration: A review.

Dielectrophoresis (DEP) is an electrokinetic effect first studied in the early 20th century. Since then, DEP has gained significant interest in research, owing to its ability to solve particle separation problems in various industries. Dielectrophoretic filtration (DEP filtration) is a separation method using DEP to filter a wide range of microparticles, from bacterial cells to catalytic particles. DEP filtration can selectively separate particles based on size or dielectric properties, recover trapped particles and avoid common problems associated with mechanical filtration based on pore size (e.g. pressure drops and regular filter replacements). This review describes the simple beginnings of DEP filtration and how our understanding and applications for DEP filtration have progressed over time. A brief section of DEP theory as well as a note on the general outlook for DEP filtration in the future is presented. DEP filtration offers an exciting opportunity to selectively separate diverse particle mixtures. To achieve such a feat, technical challenges such as Joule Heating and low throughputs must be addressed.

Polycyclic aromatic hydrocarbons in ship breaking area and associated ecological risk assessment: evidence from the Sitakund ship-breaking area in Bangladesh.

Ship-breaking yards are recognized for releasing hazardous polycyclic aromatic hydrocarbons (PAHs), leading to severe environmental pollution in the sediment of ship-breaking areas. This study assessed the concentrations of 16 priority PAHs in surface sediments collected from the intertidal zone adjacent to the Sitakund ship-breaking yards. The samples underwent Soxhlet extraction and detection using PerkinElmer GC-Clarus 690 and MS-Clarus SQ8C with an Elite-5MS capillary column (30 m × 0.25 mm ID × 0.25 µm). The study utilized PAH concentrations to reveal spatial distribution patterns, identify point sources, and assess potential toxicity. The total PAH concentration ranged from 1899.2 to 156,800.08 ng g-1 dw, while the concentration of 7 carcinogenic PAHs ranged from 822.03 to 1899.15 ng g-1 dw. High molecular weight PAHs dominated among the 16 PAHs, whereas low molecular weight PAHs, such as 2-ring PAHs, were negligible. Source characterization based on different molecular ratios suggested that PAHs in the area originated from pyrolytic processes related to ship dismantling, fishing activities, and water transportation for people. The observed PAH concentrations exceeded both national and international standards for sedimentary PAH levels, indicating significant ecological risks. The total TEQcarc values of sediment samples varied from 564.41 to 10,695.12 ng g-1, with a mean value of 3091.25 ng g-1. The study's findings underscore the immediate biological damage that PAH contamination in the Sitakund ship-breaking area could cause, emphasizing the need for effective control measures to ensure ecological and human safety.

The FAM114A proteins are adaptors for the recycling of Golgi enzymes.

Golgi resident enzymes remain in place whilst their substrates flow through from the endoplasmic reticulum to elsewhere in the cell. COPI-coated vesicles bud from the Golgi to recycle Golgi residents to earlier cisternae. Different enzymes are present in different parts of the stack, and one COPI adaptor protein, GOLPH3, acts to recruit enzymes into vesicles in part of the stack. We used proximity biotinylation to identify further components of intra-Golgi vesicles and found FAM114A2, a cytosolic protein. Affinity chromatography with FAM114A2, and its paralogue FAM114A1, showed that they bind to Golgi resident membrane proteins, with membrane-proximal basic residues in the cytoplasmic tail being sufficient for the interaction. Deletion of both proteins from U2OS cells did not cause substantial defects in Golgi function. However, a Drosophila orthologue of these proteins (CG9590/FAM114A) is also localised to the Golgi and binds directly to COPI. Drosophila mutants lacking FAM114A have defects in glycosylation of glue proteins in the salivary gland. Thus, the FAM114A proteins bind Golgi enzymes and are candidate adaptors to contribute specificity to COPI vesicle recycling in the Golgi stack.