Thermoluminescence and ATR-FTIR study of UVC-irradiated low-density polyethylene (LDPE) food packaging.

This research aims to study the effects of ultraviolet C (UVC) radiation on low-density polyethylene (LDPE) food packaging. Main objectives include evaluating LDPE degradation and detecting UVC radiation using thermoluminescent dosimeters (TLDs) placed under LDPE samples. Results confirm accurate UVC detection after one hour of exposure, providing a useful tool for optimize food treatment procedures. ATR-FTIR spectroscopy analysis revealed subtle alterations (<8 % transmittance relative) in UVC-irradiated LDPE samples, including possible CH breakage (2910 and 2848 cm-1) and potential CC bond vibrations (1470 cm-1), among others. However, observed variations may stem from LDPE properties rather than entirely from UVC radiation. A comparative study of UVC-induced thermoluminescence (TL) emissions provided insights into various TLDs materials. TL kinetic analysis, using computerised glow curve deconvolution (CGCD) method, unveiled trap charge activation due to UVC exposure, including partial ionization, bleaching effect and photo-transfer (PTTL) processes. LDPE samples amplified UVC-TL responses, revealing intensity differences between the TLDs attributed to the PTTL process, accentuated by the lack of an annealing treatment. Additionally, chemical composition of the TL detectors such as, type, concentration, number, oxidation states and ionic radii of their dopants may influence UVC-TL response. Consequently, TL intensity ratios follow as: GR-200 (LiF: Mg, Cu, P) > TLD-100 (LiF: Ti, Mg) > TLD-400 (CaF2: Mn) > TLD-200 (CaF2: Dy). Thus, GR-200 detects ionizing radiation but cannot distinguish between ionizing and non-ionizing UVC radiation, while TLD-100 has limited effectiveness as a UVC radiation detector. In contrast, TLD-400 is suitable for detecting UVC radiation and TLD-200 emerges as the most favorable UVC detector, showing consistent response levels and minimal PTTL effect placed under the LDPE samples without the need of a thermal annealing treatment that makes the TLD-200 to be reusable in a low-cost measurement protocol.

Ultraviolet C irradiation enhances the resistance of grape against postharvest black rot (Aspergillus carbonarius) by regulating the synthesis of phenolic compounds.

UV-C irradiation can maintain fruit quality by inducing fruit disease resistance and reducing decay during storage. Grape (Vitis Vinifera L.) was exposed to 2.4 kJ m-2 UV-C irradiation then inoculated with Aspergillus carbonarius to investigate the changes in nutritional quality, defense related substances and enzyme activities. Postharvest UV-C irradiation can increased the levels of defense-related substances and enzyme activities, such as phenols, flavanols, lignin, proline, glutathione, phenylalanine ammonia-lyase (PAL), polyphenol oxidase (PPO), and ß-1,3-glucanase (GLU). In addition, Resveratrol plays an important role in grape resistance to A. carbonarius infection through further verification by gene expression levels, the transcription factors VvWRKY24 and VvMYB14 are highly correlated with the regulation of VvSTS gene expression. This study revealed the molecular mechanism of postharvest grape fruit response to UV-C irradiation and the defense mechanism against black rot, and provided a theoretical basis for postharvest grape storage and preservation technology.

Enhancing Raw Bovine Milk Quality using Ultraviolet-C (UV-C) Irradiation: A Microbial and Lipid Peroxidation Study.

This study investigated the efficacy of ultraviolet-C (UV-C) irradiation in enhancing the quality of raw bovine milk by targeting microbial populations and lipid peroxidation, both of which are key factors in milk spoilage. We categorized the raw milk samples into three groups based on initial bacterial load: low (<3 Log 10 CFU/mL), medium (3-4 Log 10 CFU/mL), and high (>4 Log 10 CFU/mL). Using a 144 W thin-film UV-C reactor, we treated the milk with a flow rate of 3 L/min. We measured the bacterial count including standard plate count, coliform count, coagulase-negative staphylococci count, and lactic acid bacteria count and lipid peroxidation (via thiobarbituric acid reactive substances assay) pre- and post-treatment. Our results show that UV-C treatment significantly reduced bacterial counts, with the most notable reductions observed in high and medium initial load samples (>4 and 3-4 Log 10 CFU/mL, respectively). The treatment was particularly effective against coliforms, showing higher reduction efficiency compared to coagulase-negative staphylococci and lactic acid bacteria. Notably, lipid peroxidation in UV-C treated milk was significantly lower than in pasteurized or untreated milk, even after 72 hours. These findings demonstrate the potential of UV-C irradiation as a pre-treatment method for raw milk, offering substantial reduction in microbial content and prevention of lipid peroxidation, thereby enhancing milk quality.

Evaluation of an Automated Wall-mounted Far Ultraviolet-C Light Technology for Continuous or Intermittent Decontamination of Candida auris on Surfaces.

Background: Technologies that provides safe and effective decontamination of surfaces and equipment between episodes of manual cleaning could be an important advance in efforts to prevent transmission of the emerging fungal pathogen Candida auris. Methods: We tested the efficacy of a novel wall-mounted far ultraviolet-C (UV-C) light technology that delivers far UV-C, when people are not detected within the field of illumination, against C. auris isolates from clades I, II, III, and IV using a quantitative disk carrier test method. In an equipment room, we examined the efficacy of the technology in reducing an isolate of C. auris from clade IV inoculated on multiple sites on portable devices. Results: The far UV-C technology reduced isolates from all 4 clades of C. auris by >3 log10 colony-forming units (CFU) aſter an 8-hour exposure on steel disks. For the clade IV isolate, similar reductions were achieved on glass and plastic carriers. In the equipment room, the technology reduced C. auris inoculated on multiple sites on portable equipment by >2 log10 CFU in 4 hours. Conclusions: The far UV-C technology could be useful for decontamination of surfaces and equipment between episodes of manual cleaning. Additional studies are needed to evaluate the use of the technology in clinical settings.

Extended Reality Head-Mounted Displays Are Likely to Pose a Significant Risk in Medical Settings While Current Classification Remains as Non-Critical.

Extended reality (XR) devices, including virtual and augmented reality head-mounted displays (HMDs), are increasingly utilised within healthcare to provide clinical interventions and education. Currently, XR devices are utilised to assist in reducing pain and improving psychological outcomes for immunocompromised patients in intensive care units, palliative care environments and surgical theatres. However, there is a paucity of research on the risks of infection from such devices in healthcare settings. Identify existing literature providing insights into the infection control risk XR HMDs pose within healthcare facilities and the efficacy of current infection control and cleaning procedures. Three databases (PubMed, Embase and CINAHL) in addition to Google Scholar were systematically searched. A total of seven studies were identified for this review. Microorganisms, including pathogenic bacteria (e.g., Staphylococcus aureus and Pseudomonas aeruginosa), were found to be present on XR HMDs. Published cleaning and infection control protocols designed to disinfect XR HMDs and protect users were heterogeneous in nature. Current cleaning protocols displayed varying levels of efficacy with microbial load affected by multiple factors, including time in use, number of users and XR HMD design features. In healthcare settings, fitting XR HMDs harbouring microorganisms near biological and mucosal entry points presents an infection control risk. An urgent revision of the Spaulding classification is required to ensure flexibility that allows for these devices to be reclassified from 'Non-critical' to 'Semi-Critical' depending on the healthcare setting and patient population (surgery, immunocompromised, burns, etc.). This review identified evidence supporting the presence of microorganisms on XR HMDs. Due to the potential for HMDs to contact mucosal entry points, devices must be re-considered within the Spaulding classification as 'Semi-critical'. The existence of microbial contaminated XR HMDs in high-risk medical settings such as operating wards, intensive care units, emergency departments, labour and delivery wards and clinical areas with immunosuppressed patients requires urgent attention. Public health authorities have a duty of care to develop revised guidelines or new recommendations to ensure efficient sanitation of such devices.

Dose-dependent physiological effects of UV-C radiation on seashore paspalum.

Positive effects of ultraviolet-C (UV-C) radiation on plants have been documented in previous literature with a focus on extending shelf life and reducing disease development. However, its effect on plant growth habits has been scarcely explored, especially in turfgrass where a compact shoot growth is a desirable trait. Seashore paspalum (Paspalum vaginatum) is a warm-season perennial turfgrass requiring low fertilizer and pesticide inputs. This project aimed to test the effects of different doses of UV-C radiation on growth and performance of seashore paspalum cv. Seastar. Here, we provide evidence of dose-dependent effects. Lower UV-C doses (6 s and 1 min daily) improved the performance of seashore paspalum, as manifested by higher tiller density, reduced clipping yields, increased chlorophyll level on selected dates as well as enhanced photosynthetic efficiency compared to control. Contrastingly, higher doses (6 min and 30 min daily) resulted in severe damage with 30-min treatment being lethal to seashore paspalum, causing marked declines in all measured parameters. This is the first time that UV-C-induced growth response was reported in turf. Conclusions drawn from this study would shed light into the effects of UV-C radiation on the growth and performance of seashore paspalum and offer exciting potential for the utilization of UV-C at non-lethal dosage in turfgrass management.

Methods for SARS-CoV-2 hospital disinfection, in vitro observations.

Introduction: Escalation of chemical disinfection during the COVID-19 pandemic has raised occupational hazard concerns. Alternative and potentially safer methods such as ultraviolet-C (UVC) irradiation and ozone have been proposed, notwithstanding the lack of standardized criteria for their use in the healthcare environment. Aim: Compare the virucidal activity of 70% ethanol, sodium dichloroisocyanurate (NaDCC), chlorhexidine, ozonated water, UVC-222 nm, UVC-254 nm against three SARS-CoV-2 variants of concern cultured in vitro. Methods: Inactivation of three SARS-CoV-2 variants (alpha, beta, gamma) by the following chemical methods was tested: ethanol 70%, NaDCC (100 ppm, 500 ppm, 1000 ppm), chlorhexidine (2%, 1% and 0.5%), ozonated water 7 ppm. For irradiation, a je2Care 222nm UVC Lamp was compared to a Sylvania G15 UV254 nm lamp. Results: Viral inactivation by >3 log was achieved with ethanol, NaDCC and chlorhexidine. The minor virucidal effect of ozonated water was <1 log. Virus treatment with UVC-254 nm reduced viral activity by 1-5 logs with higher inactivation after exposure for 3 minutes compared to 6 seconds. For all three variants, under equivalent conditions, exposure to UVC-222 nm did not achieve time-dependent inactivation as was observed with treatment with UVC-254 nm. Conclusion: The virucidal activity on replication-competent SARS-CoV-2 by conventional chemical methods, including chlorhexidine at concentrations as low as 0.5%, was not matched by UVC irradiation, and to an even lesser extent by ozonated water treatment.

Irreversible inhibition of estrogen receptor α signaling and the emergence of hormonal resistance in MCF7 breast cancer cells induced by DNA damage agents.

Combining chemotherapy and hormone therapy is a prevalent approach in breast cancer treatment. While the cytotoxic impact of numerous chemotherapy drugs stems from DNA damage, the exact role of these DNA alterations in modulating estrogen receptor α (ERα) machinery remains elusive. The present study aimed to analyze the impact of DNA damage agents on ERα signaling in breast cancer cells and assess the signaling pathways mediating the influence of DNA damage drugs on the ERα machinery. Cell viability was assessed using the MTT method, while the expression of signaling proteins was analyzed by immunoblotting. ERα activity in the cells treated with various drugs (17ß-estradiol, tamoxifen, 5-fluorouracil) was assessed through reporter gene assays. In vitro experiments were conducted on MCF7 breast cancer cells subjected to varying durations of 5-fluorouracil (5-FU) treatment. Two distinct cell responses to 5-FU were identified based on the duration of the treatment. A singular dose of 5-FU induces pronounced DNA fragmentation, temporally suppressing ERα signaling while concurrently activating AKT phosphorylation. This suppression reverses upon 5-FU withdrawal, restoring normalcy within ten days. However, chronic 5-FU treatment led to the emergence of 5-FU-resistant cells with irreversible alterations in ERα signaling, resulting in partial hormonal resistance. These changes mirror those observed in cells subjected to UV-induced DNA damage, underscoring the pivotal role of DNA damage in shaping estrogen signaling alterations in breast cancer cells. In summary, the results of the present study suggested that the administration of DNA damage agents to cancer cells can trigger irreversible suppression of estrogen signaling, fostering the development of partial hormonal resistance. This outcome may ultimately impede the efficacy of combined or subsequent chemo- and hormone therapy strategies.

UV-C LED-induced cyclobutane pyrimidine dimer formation, lesion repair and mutagenesis in the biofilm-forming diatom, Navicula incerta.

The use of ultraviolet-C (UV-C) irradiation in marine biofouling control is a relatively new and potentially disruptive technology. This study examined effects of UV-C exposure on the biofilm-forming diatom, Navicula incerta. UV-C-induced mutations were identified via Illumina HiSeq. A de novo genome was assembled from control sequences and reads from UV-C-exposed treatments were mapped to this genome, with a quantitative estimate of mutagenesis then derived from the frequency of single nucleotide polymorphisms. UV-C exposure increased cyclobutane pyrimidine dimer (CPD) abundance with a direct correlation between lesion formation and fluency. Cellular repair mechanisms gradually reduced CPDs over time, with the highest UV-C fluence treatments having the fastest repair rates. Mutation abundances were, however, negatively correlated with CPD abundance suggesting that UV-C exposure may influence lesion repair. The threshold fluence for CPD formation exceeding CPD repair was >1.27 J cm-2. Fluences >2.54 J cm-2 were predicted to inhibit repair mechanisms. While UV-C holds considerable promise for marine antifouling, diatoms are just one, albeit an important, component of marine biofouling communities. Determining fluence thresholds for other representative taxa, highlighting the most resistant, would allow UV-C treatments to be specifically tuned to target biofouling organisms, whilst limiting environmental effects and the power requirement.

Enhancing Performance of Ultraviolet C Photodetectors Through Single-Domain Epitaxy of Monoclinic ß-Ga2 O3 Films and Tailored Anti-Reflection Coating.

Implementing high-performance ultraviolet C photodetectors (UVC PDs) based on ß-Ga2 O3 films is challenging owing to the anisotropic crystal symmetry between the epitaxial films and substrates. In this study, highly enhanced state-of-the-art photoelectrical performance is achieved using single-domain epitaxy of monoclinic ß-Ga2 O3 films on a hexagonal sapphire substrate. Unlike 3D ß-Ga2 O3 films with twin domains, 2D ß-Ga2 O3 films exhibit a single domain with a smooth surface and low concentration of point defects, which enable efficient charge separation by suppressing boundary-induced recombination. Furthermore, a tailored anti-reflection coating (ARC) is adopted as a light-absorbing medium to improve charge generation. The tailored nanostructure, which features a gradient refractive index, not only substantially reduces the reflection, but also suppresses the surface leakage current as a passivation layer. This study provides fundamental insights into the single-domain epitaxy of ß-Ga2 O3 films and the application of ARC for the development of high-performance UVC PDs.

Ultraviolet-C mediated inactivation of Candida auris, a rapid emerging health threat.

Health care-associated infections, particularly those caused by multidrug-resistant organisms (MDROs), pose significant challenges to patient safety. Candida auris (C auris), an emerging MDRO fungus, has been acknowledged as an urgent threat by the Centers for Disease Control and Prevention due to its high mortality and difficulty in prevention, diagnosis, and treatment. In this study, we investigated the efficacy of 254 nm ultraviolet-C light (UV-C) in inactivating C auris on hard surfaces. A mobile UV-C tower equipped with high-performance bulbs was used, and within 7 minutes of continuous exposure, ≥99.97% (≥3.86 log10) inactivation of C auris was achieved in a patient-room-sized test chamber. Our findings suggest that UV-C can serve as an adjunct infection control measure for preventing C auris and other MDRO Health care-associated infections in health care settings. Implementation of UV-C disinfection protocols can contribute to enhanced patient safety and combat the growing threat of MDRO pathogens.

Can Extraintestinal Pathogenic Escherichia coli with Heat Resistance Profile Overcome Nonthermal Technologies?

Ultraviolet-C light-emitting diode (UVC-LED) and ultrasound (US) are two nonthermal technologies with the potential to destroy pathogens. However, little is known about their effectiveness in strains with a history of heat resistance. Thus, this study aimed to evaluate the phenotype and genotype of heat-resistant extraintestinal pathogenic Escherichia coli (ExPEC) with heat resistance genes after the application of US, UVC-LED, and UVC-LED+US. For this, two central composite rotatable designs were used to optimize the UVC-LED and US conditions in four ExPEC isolated from beef. From the genome of these isolates obtained in a previous study, possible genes for UVC resistance were analyzed. Results showed that US was ineffective in reducing >0.30 log colony-forming unit/mL, and that when used after UVC-LED, it showed a nonsynergic or antagonistic effect. Also, UVC-LED had the greatest effect at the maximum dose (4950 mJ/cm2 from 1.65 mW/cm2 for 50 min). However, the strains showed some recovery after that, which could be implicated in the expression of genes included in SOS system genes, some others present in the transmissible Locus of Stress Tolerance (trxBC and degP), and others (terC). Thus, ExPEC can overcome the conditions used in this study for US, UVC-LED, and UVC-LED+US, probably due to the history of resistance to other cellular damage. The result of this study will contribute to future studies that aim to find better treatment conditions for each food product.

Hybrid Radiant Disinfection: Exploring UVC and UVB Sterilization Impact on the Mechanical Characteristics of PLA Materials.

This study explores the impact of disinfection techniques on the mechanical properties of poly(lactic acid) (PLA), a crucial material in the production of medical implants, tissue engineering, orthopedic devices and drug delivery systems, owing to its biocompatibility and ease of manufacturing. The focus is on evaluating the effectiveness of ultraviolet (UV) type C (254 nm wavelength) and the combined use of type C and B (310 nm wavelength) disinfection methods. Fifteen tensile test specimens (ASTM D638) and fifteen compression test specimens (ASTM D695) were utilized to assess PLA's mechanical properties, including yield strength, ultimate strength, and fracture strength. The investigation involved subjecting the specimens to the specified disinfection methods and evaluating these properties both before and after the disinfection process. In the tensile test, a statistically significant difference (p = 0) in yield displacement was observed among the three groups. Additionally, a notable difference (p = 0.047) in fracture displacement was identified between the untreated group and the UVC and UVB combination group. No discernible impact on yield or fracture forces was noted. In the compression test, there was a significant difference (p = 0.04) in yield displacement and a clear difference (p = 0.05) in fracture force between the untreated group and the UVC and UVB combination group. The hybrid combination of UVC and UVB disinfection techniques did not affect yield force in both tensile and compression tests. However, it demonstrated a clear impact on displacement, suggesting its potential as a promising disinfection technique in the medical field.

Is the combination of UV-C light and bleach less effective than bleach alone for intensive care unit surface disinfection?

Background: Chlorine-based disinfectants, such as bleach, are commonly used for cleaning in healthcare settings to prevent the transmission of nosocomial pathogens. To enhance the efficacy of disinfection, ultraviolet-C (UV-C) light systems have been proposed to supplement standard cleaning procedures. As bleach decomposes in UV light, we hypothesised that the use of UV-C light as an adjunct to manual cleaning with bleach, may decrease the efficacy of disinfection instead. Methods: In the laboratory, stainless steel sheets and plastic keyboards were inoculated with Pseudomonas aeruginosa (∼106 CFU/ml) and subjected to treatment with either UV-C light only, bleach only or a combination of UV-C light and bleach. The residual bioburden (CFU/ml) was quantified through conventional microbiological techniques. Results were compared to non-exposed control surfaces and against each treatment strategy. Results: On tested surfaces, there were statistically significant reductions in P. aeruginosa when surfaces were treated with UV-C light only (>2.5 log10 reduction), bleach only (>5.6 log10 reduction) and a combination of UV-C light and bleach (>6.3 log10 reduction) compared to positive control (P < 0.001, all treatment strategies). No significant differences were observed when surfaces were treated with the addition of UV-C light to bleach compared to treatment with bleach alone. Conclusion: There was no difference in the efficacy of disinfection against P. aeruginosa with the combined treatment strategy of UV-C light and bleach compared to bleach alone under laboratory conditions. Further studies are warranted to elucidate the effectiveness of this technology on other healthcare-associated pathogens.

Enhancing post-harvest quality of sapota using ultraviolet-C irradiation: A study on efficacy and effects.

Ultraviolet-C (UV-C) radiation has been identified as a promising method for enhancing the shelf life of fruits and vegetables by reducing microbial count and boosting their defence mechanisms. In this study, the impact of UV-C radiation on the physical, biochemical, and microbial properties of sapota fruits was investigated by subjecting them to different doses (2.5, 5, 7.5, and 10 kJ m-2; 12 ± 1°C; 85-90% relative humidity) to enhance their shelf life. The results revealed that higher doses of UV-C radiation resulted in significantly lower weight loss and higher firmness compared to untreated samples and samples treated with lower doses. Furthermore, UV-C-treated fruits displayed a delayed increase in total soluble solids, total sugar, and reduced sugar content compared to the untreated fruit during storage. The UV-C-treated fruits also exhibited a delayed decline in ascorbic acid and titratable acidity during storage. The treated fruits exhibited significantly higher phenolic content than the untreated fruits. Additionally, significantly lower decay and microbial count were observed in fruits treated with higher doses than in those treated with lower doses. The samples treated with a dose of 7.5 and 10 kJ m-2 had a shelf life of 25 days compared to 14 days for the control fruits.

Update on potential interventions to reduce the risk for transmission of health care-associated pathogens from floors and sinks.

Health care facility floors and sink drains and other wastewater drainage sites are universally contaminated with potential pathogens and there are plausible mechanisms by which organisms can be disseminated from these sites. However, floors and sink drains are not addressed as potential sources of pathogen transmission in most health care facilities. One factor that has hindered progress in addressing floors and sinks has been the lack of practical and effective measures to reduce the risk for dissemination of organisms from these sites. This article provides an update on some of the potential interventions being used to reduce the risk for transmission of health care-associated pathogens from floors and sinks. Practical approaches to address these sites of contamination are emphasized.

High technology and low technology measures to reduce risk of SARS-CoV-2 transmission.

During the coronavirus disease 2019 (COVID-19) pandemic, a variety of low technology and high technology measures have been proposed to reduce the risk for transmission. Identifying those measures likely to be useful in reducing viral transmission without undue expense or potential for adverse effects has been a challenge for infection control programs. The challenge has been compounded by the lack of tools that can be used to assess the risk for viral transmission in different settings. This review discusses practical tools that can be used to assess ventilation and airflow and evaluates some of the low technology and high technology measures that have been proposed as control measures for COVID-19. Some typical questions posed to infection control programs during the pandemic are presented to illustrate real-world application of the concepts being discussed.

Do mobile phone surfaces carry SARS-CoV-2 virus? A systematic review warranting the inclusion of a "6th" moment of hand hygiene in healthcare.

BACKGROUND: Mobile phones, used in billions throughout the world, are high-touch devices subject to a dynamic contamination of microorganisms and rarely considered as an important fomite to sanitise systematically. The emergence of SARS-CoV-2 resulted in the COVID-19 pandemic, arguably the most impactful pandemic of the 21st century with millions of deaths and disruption of all facets of modern life globally. AIM: To perform a systematic review of the literature exploring SARS-CoV-2 presence as a contaminant on mobile phones. METHODS: A systematic search (PubMed and Google Scholar) of literature was undertaken from December 2019 to March 2023 identifying English language studies. Studies included in this review specifically identified or tested for the contamination of the SARS-CoV-2 virus or genome on mobile phones while studies testing for SARS-COV-2 in environments and/or other fomites samples than but not mobile phones were excluded. RESULTS: A total of 15 studies with reports of SARS-CoV-2 contamination on mobile phones between 2020 and 2023 were included. Amongst all studies, which encompassed ten countries, 511 mobile phones were evaluated for the presence of SARS-CoV-2 contamination and 45% (231/511) were positive for SARS-CoV-2. All studies were conducted in the hospital setting and two studies performed additional testing in residential isolation rooms and a patient's house. Four studies (3 in 2020 and one in 2021) reported 0% contamination while two other studies (in 2020 and 2022) reported 100% of mobile phone contamination with SARS-COV-2. All other studies report mobile phones positive for the virus within a range of 4-77%. CONCLUSION: A total of 45% of mobile phones are contaminated with SARS-CoV-2 virus. These devices might be an important fomite vector for viral dissemination worldwide. Competent health authorities are advised/recommended to start a global implementation of mobile phone decontamination by introducing regulations and protocols in public health and health care settings such as the 6th moment of hand washing.

Managing Corneal Infections: Out with the old, in with the new?

There have been multiple reports of eye infections caused by antibiotic-resistant bacteria, with increasing evidence of ineffective treatment outcomes from existing therapies. With respect to corneal infections, the most commonly used antibiotics (fluoroquinolones, aminoglycosides, and cephalosporines) are demonstrating reduced efficacy against bacterial keratitis isolates. While traditional methods are losing efficacy, several novel technologies are under investigation, including light-based anti-infective technology with or without chemical substrates, phage therapy, and probiotics. Many of these methods show non-selective antimicrobial activity with potential development as broad-spectrum antimicrobial agents. Multiple preclinical studies and a limited number of clinical case studies have confirmed the efficacy of some of these novel methods. However, given the rapid evolution of corneal infections, their treatment requires rapid institution to limit the impact on vision and prevent complications such as scarring and corneal perforation. Given their rapid effects on microbial viability, light-based technologies seem particularly promising in this regard.

Effect of gamma and Ultraviolet-C sterilization on BMP-7 level of indigenously prepared demineralized freeze-dried bone allograft.

The presence of bone morphogenetic proteins in demineralized freeze-dried bone allograft (DFDBA) are responsible for developing hard tissues in intraosseous defects. The most common mode of sterilization of bone allografts, i.e., Gamma rays, have dramatic effects on the structural and biological properties of DFDBA, leading to loss of BMPs. Ultraviolet-C radiation is a newer approach to sterilize biodegradable scaffolds, which is simple to use and ensures efficient sterilization. However, UV-C radiation has not yet been effectively studied to sterilize bone allografts. This study aimed to compare and evaluate the effectiveness of Gamma and Ultraviolet-C rays in sterilizing indigenously prepared DFDBA and assess their effect on the quantity of BMP-7 present in the allograft. DFDBA samples from non-irradiated, gamma irradiated, and UV-C irradiated groups were tested for BMP-7 level and samples sterilized with gamma and UV-C rays were analysed for sterility testing. The estimated mean BMP-7 level was highest in non-irradiated DFDBA samples, followed by UV-C irradiated, and the lowest in gamma irradiated samples. Our study concluded that UV-C rays effectively sterilized DFDBA as indicated by negative sterility test and comprised lesser degradation of BMP-7 than gamma irradiation.