Two flavors in adulterated sesame oil: discovery, confirmation, and content regularity study.

Exploring and accurately detecting new adulteration markers in sesame oil is an important measure for sesame oil adulteration monitoring. In this study, two endogenous flavors sulfurol and γ-nonalactone which can be used as potential adulteration markers were first discovered in sesame oil and accurately quantified. First, the two endogenous flavors were discovered using gas chromatography-mass spectrometry (GC-MS), and their structures were confirmed by comparing the mass spectrograms with the NIST spectral library. Then the liquid chromatography-tandem mass spectrometry (LC-MS/MS) method using direct methanol extraction pretreatment and vanillin-D3 as an internal standard was developed for rapid quantitation and application. The method was successfully validated with recoveries ranging from 88.5% to 102.2% and relative standard deviations between 2.6% and 10.5% (n = 6). The combined method of GC-MS and LC-MS/MS was indicated to be efficient and highly sensitive for detection of sulfurol and γ-nonalactone in edible oil. Subsequently, 31 sesame oils from the market were detected, revealing that 31 samples contained the identified flavors within a relatively consistent range. However, the concentration of these flavor substances in one sample was abnormally high, indicating that there was a potential risk of adulteration. Therefore, the developed method shows good potential for quality evaluation and adulteration screening of sesame oil.

Combined pulsed electric field-ultrasound assisted extraction of yarrow phenolic-rich ingredients and their nanoliposomal encapsulation for improving the oxidative stability of sesame oil.

In this research, yarrow phenolic-rich extract was produced using pulsed electric field (PEF)-ultrasound assisted technology. The highest extraction efficiency (5.99 %) was obtained at 6.25 kV/cm of PEF and the sonication time of 60 min. As the PEF intensity and sonication time rose, the total phenolic content (TPC) and ferric-reducing power (RP) of the extracts increased. The PEF intensity of 2.70 kV/cm and sonication time of 45.83 min were the optimum extraction conditions resulting in the highest extraction efficiency, TPC, and RP. Then, this optimum extract was loaded into nanoliposomes. At higher extract levels, the encapsulation efficiency lowered, while the particle size, polydispersity index (PDI), and zeta potential of the nanoliposomal samples elevated. The results of Fourier transform infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC) confirmed the successful encapsulation of yarrow extract into nanoliposomal carriers; the sample containing the extract had the highest enthalpy (3600 J/g) and nanoliposomes loaded with yarrow antioxidant extract (0.11 mL/mg) was the optimum sample. Finally, the sesame oil containing 500 ppm free and nanoliposome extract, as well as the sample with 200 ppm BHT were evaluated for oxidative stability. The highest oxidation stability (14.21 h) belonged to the oil containing nanoliposomal yarrow phenolic extract.

Long-term stability and bactericidal properties of galenic formulations of Cannabis sativa oils.

The long-term stability in real and accelerated time for galenic oils based on full-spectrum cannabis has been studied, using sesame oil as a dilutant. Sesame oil is one of the most used vehicles in the cannabis pharmaceutical industry due to the costs and increased oral bioavailability of cannabinoids. The real-time assays conducted at 25 °C over twelve months demonstrated high stability and showed no significant changes in the composition of cannabinoids, total polyphenols, flavonoids, or antioxidant capacity. In these studies, it was observed that there was no development of microorganisms compromising the stability of the oils over a year. The three oil varieties exhibited a high bactericidal capacity against E. coli, S. aureus, and P. larvae.

Sesame lignans modulate aroma formation in sesame oil through the Maillard reaction and lipid oxidation in model systems.

The unknown effect of sesame lignans on aroma formation in sesame oil via the Maillard reaction (MR) and lipid oxidation was investigated. Sesamin, sesamolin, or sesamol was added to 3 models: lysine+glucose (MR), cold-pressed sesame oil (SO), and MR + SO, and were heated at 120 °C for 60 min. All three lignans suppressed SO oxidation while increasing DPPH scavenging ability (p < 0.05). Lignans increased depletions of lysine and glucose and MR browning (p < 0.05). Lignans reduced most aroma-active pyrazines, aldehydes, ketones, alcohols, and esters (p < 0.05). Sesamol and sesamolin increased perceptions of the preferable aromas of nutty, roasted sesame, and popcorn while reducing the undesirable green and rancid aromas (p < 0.05). Sesamol demonstrated a stronger effect on lipid oxidation, MR browning, aroma formation, and sensory perception than sesamin and sesamolin. This study suggests that sesame lignans can modulate aroma formation and sensory perception of sesame oil by interacting with the MR and lipid oxidation pathways.

Formulation Development and Evaluation of Cannabidiol Hot-Melt Extruded Solid Self-Emulsifying Drug Delivery System for Oral Applications.

Cannabidiol (CBD) is a highly lipophilic compound with poor oral bioavailability, due to poor aqueous solubility and extensive pre-systemic metabolism. The aim of this study was to explore the potential of employing Hot Melt Extrusion (HME) technology for the continuous production of Self Emulsifying Drug Delivery Systems (SEDDS) to improve the solubility and in vitro dissolution performance of CBD. Accordingly, different placebos were processed through HME in order to obtain a lead CBD loaded solid SEDDS. Two SEDDS were prepared with sesame oil, Poloxamer 188, Gelucire®59/14, PEO N80 and Soluplus®. Moreover, Vitamin E was added as an antioxidant. The SEDDS formulations demonstrated emulsification times of 9.19 and 9.30 min for F1 and F2 respectively. The formed emulsions showed smaller droplet size ranging from 150-400 nm that could improve lymphatic uptake of CBD and reduce first pass metabolism. Both formulations showed significantly faster in vitro dissolution rate (90% for F1 and 83% for F2) compared to 14% for the pure CBD within the first hour, giving an enhanced release profile. The formulations were tested for stability over a 60-day time period at 4°C, 25°C, and 40°C. Formulation F1 was stable over the 60-day time-period at 4°C. Therefore, the continuous HME technology could replace conventional methods for processing SEDDS and improve the oral delivery of CBD for better therapeutic outcomes.

Effects of different precursors on the structure of lignin-based biochar and its ability to adsorb benzopyrene from sesame oil.

Agricultural by-products of sesame are promising bioresources in food processing. This study extracted lignin from the by-products of sesame oil production, namely, the capsules and straw of black and white sesame. Using acid, alkali, and ethanol methods, 12 distinct lignins were obtained to prepare biochar, aiming to investigate both the structural characteristics of lignin-based biochar (LBB) and its ability to remove benzo[a]pyrene (BaP) from sesame oil. The results showed that white sesame straw was the most suitable raw material for preparing biochar. In terms of the preparation method, acid-extracted lignin biochar was more effective in removing BaP than alkaline or ethanol methods. Notably, WS-1LB (white sesame straw acid-extracted lignin biochar) exhibited the highest BaP adsorption efficiency (91.44 %) and the maximum specific surface area (1065.8187 m2/g), characterized by porous structures. The pseudo 2nd and Freundlich models were found to be the best fit for the adsorption kinetics and isotherms of BaP on LBB, respectively, suggesting that a multilayer adsorption process was dominant. The high adsorption of LBB mainly resulted from pore filling. This study provides an economical and highly efficient biochar adsorbent for the removal of BaP in oil.

Sesame oil as a partial substitute for egg yolk in goat semen extenders.

This study aimed to evaluate the effects of replacing egg yolk extender with sesame oil on the quality of sperm in goats following incubation at 37°C, chilling at 4°C, and freezing. Semen samples were collected from four intact male goats. The individual semen sample was divided into six groups consisting of a control group and five treatment groups with different egg yolk-to-sesame oil ratios. Seminal plasma was removed, and the sperm pellet was diluted with experimental semen extenders. The control group contained an extender of 10 % egg yolk (SO0), and the experimental extenders were composed of 8.75 % egg yolk and 1.25 % sesame oil (SO1.25); 7.5 % egg yolk and 2.5 % sesame oil (SO2.5); 5 % egg yolk and 5 % sesame oil (SO5); 2.5 % egg yolk and 7.5 % sesame oil (SO7.5); and 10 % sesame oil (SO10). Each group of semen was divided into three groups, incubated at 37°C for 1 h, chilled at 4°C for 4 h, or frozen for 24 h. Five replicates were performed. Sperm quality was evaluated, including motility, viability, and functional membrane integrity. The SO1.25 group achieved the highest sperm quality rate among the treatment groups, and the extender did not have a negative effect compared to the control. However, the total replacement of egg yolk with sesame oil in an extender resulted in the lowest sperm quality. In conclusion, the ratios of egg yolk and sesame oil that were acceptable for goat semen cryopreservation were 8.75 % and 1.25 %, respectively.

Probing the stability and quality of the cellulose-based Pickering emulsion containing sesamolin-enriched sesame oil by chemometrics-assisted ATR-FTIR spectroscopy.

This study presents the employment of Fourier transform infrared (FTIR) spectroscopy with attenuated total reflection and principal component analysis (PCA) to analyze the stability of a Pickering emulsion stabilized by carboxylated-cellulose nanocrystal (cCNC) comprising sesame oil phases with or without sesamolin. FTIR measurements identified an intermolecular hydrogen bond between the ester group of the triglyceride and the carboxyl group of the cCNC to create the emulsion droplet. The spectral bands from the hydroxyl group vibration (3700-3050 cm-1), carbonyl (1744 cm-1), CO groups of the ester triglyceride and cCNC (1160-998 cm-1) markedly discriminated between stabilized and destabilized emulsions. The PCA of FTIR spectra detected the change of molecular interaction during storage according to creaming, aggregation, and coalescence and changes in physicochemical parameters such as droplet size, refractive index, and zeta potential. Hence, PCA enabled the observation of the destabilization of emulsion in real-time.

The interaction between lipid oxidation and the Maillard reaction model of lysine-glucose on aroma formation in fragrant sesame oil.

The formation mechanism behind the sophisticated aromas of sesame oil (SO) has not been elucidated. The interaction effects of the Maillard reaction (MR) and lipid oxidation on the aroma formation of fragrant sesame oil were investigated in model reaction systems made of l-lysine (Lys) and d-glucose (Glc) with or without fresh SO (FSO) or oxidized SO (OSO). The addition of OSO to the Lys-Glc model increased the MR browning at 294 nm and 420 nm and enhanced the DPPH radical scavenging activity greater than the addition of FSO (p < 0.05). The presence of lysine and glucose inhibited the oxidation of sesame oil, reduced the loss of γ-tocopherol, and facilitated the formation of sesamol (p < 0.05). The Maillard-lipid interaction led to the increased concentrations of some of the alkylpyrazines, alkylfurans, and MR-derived ketones and acids (p < 0.05) while reducing the concentrations of other pyrazines, lipid-derived furans, aliphatic aldehydes, ketones, alcohols, and acids (p < 0.05). The addition of FSO to the MR model enhanced the characteristic roasted, nutty, sweet, and fatty aromas in sesame oil (p < 0.05), while excessive lipid oxidation (OSO) brought about an unpleasant oxidized odor and reduced the characteristic aromas. This study helps to understand the sophisticated aroma formation mechanism in sesame oil and provides scientific instruction for precise flavor control in the production of sesame oil.

Comparison of methods for activating sesame stalk lignin biochar for removing benzo[a]pyrene from sesame oil.

In this study, three activators and two activation methods were employed to activate sesame lignin-based biochar. The biochar samples were comprehensively characterized, their abilities to adsorb benzo[a]pyrene (BaP) from sesame oil were assessed, and the mechanism was analyzed. The results showed that the biochar obtained by one-step activation was more effective in removing BaP from sesame oil than the biochar produced by two-step activation. Among them, the biochar generated by one-step activation with ZnCl2 as the activator had the largest specific surface area (1068.8776 m3/g), and the richest mesoporous structure (0.7891 m3/g); it removed 90.53 % of BaP from sesame oil. BaP was mainly adsorbed by the mesopores of biochar. Mechanistically, pore-filling, π-π conjugations, hydrogen bonding, and n-π interactions were involved. The adsorption was spontaneous and heat-absorbing. In conclusion, the preparation of sesame lignin biochar using one-step activation with ZnCl2 as the activator was found to be the best for removing BaP from sesame oil. This biochar may be an economical adsorbent for the industrial removal of BaP from sesame oil.

Identification of Adulteration of Flaxseed Oil From QINGHAI Area Using GC-MS Profiling of Phytosterol Composition and Chemometrics.

Flaxseed oil is an important source of vegetable oil with a polyunsaturated fatty acid. It is significant to establish a method to quickly identify adulterated flaxseed oil. In the present study, the qualitative and quantitative analysis of phytosterol of flaxseed oil from different varieties and different production areas in the Qinghai area was first performed by gas chromatography-mass spectrometry (GC-MS) and the phytosterol standard profile of flaxseed oil was established. Then, a combination of similarity evaluation and cluster analysis was used to distinguish pure flaxseed oil from flaxseed oil adulterated with concentrations of 10-50% rapeseed oil, peanut oil, sunflower oil, and sesame oil, and discriminant analysis was used to identify the types of adulterated flaxseed oil. The results showed that similarity evaluation combined with cluster analysis can distinguish pure and adulterated flaxseed oil when the concentration of the adulterant was greater than 10%. Discriminant analysis models accurately identified the types of adulterating oil in flaxseed oil when the concentration of rapeseed, peanut, or sunflower oil was greater than 20%, and that of sesame oil was greater than 30%. This study shows that the determination of the phytosterol composition and chemometrics is a valuable tool to evaluate the purity of flaxseed oil.

Aromatic Fingerprints: VOC Analysis with E-Nose and GC-MS for Rapid Detection of Adulteration in Sesame Oil.

Food quality assurance is an important field that directly affects public health. The organoleptic aroma of food is of crucial significance to evaluate and confirm food quality and origin. The volatile organic compound (VOC) emissions (detectable aroma) from foods are unique and provide a basis to predict and evaluate food quality. Soybean and corn oils were added to sesame oil (to simulate adulteration) at four different mixture percentages (25-100%) and then chemically analyzed using an experimental 9-sensor metal oxide semiconducting (MOS) electronic nose (e-nose) and gas chromatography-mass spectroscopy (GC-MS) for comparisons in detecting unadulterated sesame oil controls. GC-MS analysis revealed eleven major VOC components identified within 82-91% of oil samples. Principle component analysis (PCA) and linear detection analysis (LDA) were employed to visualize different levels of adulteration detected by the e-nose. Artificial neural networks (ANNs) and support vector machines (SVMs) were also used for statistical modeling. The sensitivity and specificity obtained for SVM were 0.987 and 0.977, respectively, while these values for the ANN method were 0.949 and 0.953, respectively. E-nose-based technology is a quick and effective method for the detection of sesame oil adulteration due to its simplicity (ease of application), rapid analysis, and accuracy. GC-MS data provided corroborative chemical evidence to show differences in volatile emissions from virgin and adulterated sesame oil samples and the precise VOCs explaining differences in e-nose signature patterns derived from each sample type.

Identification of sunflower, rapeseed, flaxseed and sesame seed oil metabolomic markers as a potential tool for oil authentication and detecting adulterations.

Testing the composition, quality and authenticity of edible oils is crucial to safeguard the consumers' rights and health. The aim of our study was to identify oil-specific markers to enable the differentiation and authentication of sunflower, sesame, flaxseed and rapeseed oils, and to evaluate their antioxidant activity, total phenolic and carotenoid content. A metabolomic approach based on liquid chromatography coupled to quadrupole-time-of-flight mass spectrometry was employed for marker discovery. Spectrophotometric method was used for determination of antioxidant activity, total phenolic and carotenoid content. 76 oil samples from the four different manufacturers were examined. We identified 13 oil-specific markers for sunflower seed oil, 8 for rapeseed oil, 5 for sesame seed oil and 3 for flaxseed oil, their retention times, accurate masses, and characteristic fragment ions are reported. The abundances of the markers for each plant species were found to vary depending on the oil producer and the product batch. Significant differences in antioxidant activity, total phenolic and carotenoid content were also observed both between oils and within oil type. The highest total phenolic content (84.03 ± 4.19 to 103.79 ± 3.67 mg of gallic acid/kg) and antioxidant activity (245.67 ± 7.59 to 297.22 ± 2.32 mg Trolox/kg) were found in sesame seed and flaxseed oils, respectively. Identified metabolic markers can be used as qualitative markers to confirm the authenticity or to detect adulterations of oils. Composition, properties and authenticity testing should be more rigorous for food products marketed as health-promoting.

Investigations on color and flavor formed by roasting sesame polysaccharide-protein mixtures.

Roasting is an important operation to produce attractive colors and distinctive flavors during the production of sesame oil. To investigate the contributions of macromolecules to the color and flavor during roasting sesame seeds, water-soluble polysaccharides (WSP) and chelator-soluble polysaccharides (CSP) sequentially extracted from sesame hull were mixed with sesame protein isolate (SPI) at different ratios (1:1, 1:2, and 2:1, w/w), then the mixtures were roasted at 180 °C for 35 min. Results showed that WSP, CSP, and SPI degraded approximately at 150 °C and SPI had the highest thermal stability. According to monosaccharide/amino acid analysis, glucose and galacturonic acid showed the highest reduction rates, as well as lysine and arginine. CSP + SPI mixtures showed greater reactivity than WSP + SPI mixtures, resulting in a darker color and many more Maillard reaction products. The predominant volatiles of roasted WSP/CSP + SPI mixtures were aldehydes and heterocyclic compounds identified by headspace solid-phase microextraction coupled with gas chromatography-mass spectrometry (HS-SPME/GC-MS). This work provides some new information about flavor and color development during roasting sesame seeds.

Influence of different thermal treatment methods on the processing qualities of sesame seeds and cold-pressed oil.

This study investigated the impact of multiple thermal treatments (explosion-puffing, microwave, and roasting) on the processing qualities of sesame seeds and cold-pressed oil. The scanning electron microscopy (SEM) showed fissures and cavities of sesame seed surface upon thermal treatments. The microwave treatment promoted the maximum conversion of sesamolin into sesamol in the sesame oil. Compared with other treatments, explosion-puffing treatment resulted in most significant increases in the multiple beneficial phytochemicals, as well as in vitro antioxidant properties determined by 2,2-dipheny1-1-picrylhydrazyl radical (DPPH) radical scavenging activity, Ferric reducing antioxidant power (FRAP) and oxidative stability index (OSI). Additionally, thermal treatment processing caused varying degrees of damage of crude protein, total amino acids (TAA) and protein structure (tertiary and second structure). In which, explosion-puffing achieved minimal reduction in the first two indicators. Collectively, explosion-puffing might be a preferable thermal treatment method for industrial sesame processing with improved quality specifications.

Application of Maillard Reaction Products Derived Only from Enzymatically Hydrolyzed Sesame Meal to Enhance the Flavor and Oxidative Stability of Sesame Oil.

The low-temperature roasting of sesame oil has become increasingly popular because of its nutritional benefits; however, the flavor is reduced. In order to improve the quality of sesame oil without exogenous addition, sesame meal was hydrolyzed and further used to prepare Maillard reaction products (MRPs) while protease hydrolysis (PH) and glucoamylase-protease hydrolysis (GPH) were used, and their respective Maillard products (PHM and GPHM) were added in the oils for reducing sugar and total sugar content determination, free amino acid determination, and color and descriptive sensory analysis, as well as electronic nose, SPME-GC-MS, odor activity value, and oxidative stability analyses. Results showed that the MRPs could be produced using the enzymatically hydrolyzed sesame meal without exogenous addition, and the oil flavor blended with GPHM (GPHM-SO) was significantly (p < 0.05) improved with the best sensory quality. The composition of pyrazines (119.35 µg/mL), furans (13.95 µg/mL), and sulfur substances (6.25 µg/mL) contributed positively to sensory properties in GPHM-SO, and 2,5-dimethylpyrazine, 2,6-dimethylpyrazine, and 2,3-dimethylpyrazine were characterized as the key flavor compounds with odor activity values of 7.01, 14.80, and 31.38, respectively. Furthermore, the oxidative stability of the oil was significantly improved with the addition of MRPs, and the shelf life of GPHM-SO was predicted to be extended by 1.9 times more than that of the crude oil based on the accelerated oxidation fitting analysis. In general, the MRPs derived only from sesame meal can enhance the flavor and oxidative stability of sesame oil and can be applied in the oil industry.

Authenticity Assessment from Sesame Seeds to Oil and Sesame Products of Various Origin by Differential Scanning Calorimetry.

The aim of this study was to conduct thermal characterization of sesame seeds and oils from various geographical origins (Ethiopia, India, Nigeria, Sudan, Turkey), different method of extraction (hexane and cold-pressing), and different types of derived products (halva and tahini). Thermal characterization was investigated using differential scanning calorimetry (DSC), which showed that origin of the seeds has no influence on the melting profile of sesame oil (peak temperature and enthalpy). Method of extraction (hexane and cold-pressing) influenced the peak temperatures of the resulting oils (p ≤ 0.05). The addition of 20% of palm olein to pure sesame oil influenced the significant changes in thermodynamic parameters such as peak temperature (Tm2), which was lowered from −5.89 °C to −4.99 °C, peak half width (T1/2), elevated from 3.01 °C to 4.52 °C, and the percentage of first peak area (% peak 1) lowered from 87.9 to 73.2% (p ≤ 0.05). The PCA method enabled to distinguish authentic and adulterated sesame oils of various origins. There were no significant differences in thermal properties among the products (halva, tahini) and the authentic sesame oil (p > 0.05). The obtained results showed DSC feasibility to characterize sesame oil and sesame products in terms of authenticity.

Effects of Seed Roasting Temperature on Sesame Oil Fatty Acid Composition, Lignan, Sterol and Tocopherol Contents, Oxidative Stability and Antioxidant Potential for Food Applications.

Roasting is a key step for preparing sesame oil that leads to important changes in its organoleptic properties and quality. In this study, white sesame seeds were roasted for 20 min in an electric oven at different temperatures (120, 150, 180, 210, 250 and 300 °C). The oils extracted from unroasted and roasted seeds were compared for their chemical composition: fatty acids (including trans isomers), phytosterols, lignans (sesamin and sesamolin), tocopherols and total phenolic compounds, as well as their oxidative stability and antiradical capacity. There were no obvious differences in the oil densities, refractive indexes or iodine values, but the saponification values were affected by temperature. Relevant primary and secondary lipid oxidation were observed at T > 250 °C, resulting in a higher p-anisidine value and K232 as well as K268 values. Roasting improved oil yield (from 33.5 to 62.6%), increased its induction period (from 5.5 to 10.5 h) and enhanced the total phenolic content (from 152 to 194 mg/100 g) and antiradical activity of the extracted oil. Depending on roasting temperature, a gradual decline was recorded in total amounts of phytosterols (up to 17.4%), γ-tocopherol (up to 10.6%), sesamolin (maximum of 27.5%) and sesamin (maximum of 12.5%). All the investigated oils presented a low quantity in triglyceride polymers, clearly below the maximum tolerated quantity according to the European regulation. The optimal roasting temperature for obtaining high nutritional grade oil within the permissible values was 210 °C. The unsaponifiable components (including lignans and sterols) extracted from roasted seeds have been shown to be natural additives to fresh meatball products to extend shelf life. The results of this study may help to boost the nutritional content of plant-based diets by allowing for the use of roasted sesame seed oil and its components.

Surface Chemistry Study of the Interactions of Sesame Oil with Meibomian Films.

A possible approach for the treatment of meibomian gland disease (MGD) can be the supplementation of meibomian gland secretion (MGS) with nonpolar lipids (NPL) rich plant oils. Sesame oil (SO), approximately equal in monounsaturated fat (oleic acid, 40% of total) and polyunsaturated fat (linoleic acid, 42% of total), has shown multiple health benefits due to its anti-inflammatory and antioxidant effects. Thus, the interactions between SO and MGS in surface layers deserve further study. Therefore, pseudobinary films were formed with controlled MGS/SO molar ratios (0%, 10%, 30%, 50%, and 100% SO) at the air/water surface of the Langmuir trough over phosphate buffered saline (pH 7.4) subphase. Surface pressure (π)-area (A) isotherms and Brewster angle microscopy observations showed nonideal interactions where SO aggregates with MGS and complements the NPL stratum of the meibomian layers. The analysis of stress relaxation transients with Kohlrausch-Williams-Watts equation revealed that the supplementation of fixed amount of MGS with excess lipids via SO altered the dilatational elasticity of the films as reflected by the increase of the exponent ß. Thus, SO with its unique combination of high oxidative stability and abundance of long polyunsaturated acyl chains might be a useful supplement to MGS layers.

Development, optimization, and evaluation of a nanostructured lipid carrier of sesame oil loaded with miconazole for the treatment of oral candidiasis.

Candida albicans is the fungus responsible for oral candidiasis, a prevalent disease. The development of antifungal-based delivery systems has always been a major challenge for researchers. This study was designed to develop a nanostructured lipid carrier (NLC) of sesame oil (SO) loaded with miconazole (MZ) that could overcome the solubility problems of MZ and enhance its antifungal activity against oral candidiasis. In the formulation of this study, SO was used as a component of a liquid lipid that showed an improved antifungal effect of MZ. An optimized MZ-loaded NLC of SO (MZ-SO NLC) was used, based on a central composite design-based experimental design; the particle size, dissolution efficiency, and inhibition zone against oral candidiasis were chosen as dependent variables. A software analysis provided an optimized MZ-SO NLC with a particle size of 92 nm, dissolution efficiency of 88%, and inhibition zone of 29 mm. Concurrently, the ex vivo permeation rate of the sheep buccal mucosa was shown to be significantly (p < .05) higher for MZ-SO NLC (1472 µg/cm2) as compared with a marketed MZ formulation (1215 µg/cm2) and an aqueous MZ suspension (470 µg/cm2). Additionally, an in vivo efficacy study in terms of the ulcer index against C. albicans found a superior result for the optimized MZ-SO NLC (0.5 ± 0.50) in a treated group of animals. Hence, it can be concluded that MZ, through an optimized NLC of SO, can treat candidiasis effectively by inhibiting the growth of C. albicans.