Optimized spray-dried conditions' impact on fatty acid profiles and estimation of in vitro digestion of spray-dried chia/fish oil microcapsules.

Long-chain polyunsaturated fatty acids (LCPUFA) are of interest due to their potential health properties and have a significant role in reducing the risk of various chronic diseases in humans. It is commonly used as a supplement. However, lipid oxidation is an important negative factor caused by environmental, processing, and limited water solubility of LCPUFA, making them difficult to incorporate into food products. The objective of this research work was to prevent oxidation, extend shelf life, enhance the stability of fatty acids, and to achieve controlled release by preparing spray-dried powder (SDM). For spray-drying, aqueous emulsion blends were formulated using a 1:1 ratio of chia seed oil (CSO) and fish oil (FO) and using a laboratory-scale spray-dryer with varying conditions: inlet air temperature (IAT, 125-185 °C), wall material (WM, 5-25%), pump speed (PS, 3-7 mL/min), and needle speed (NS, 3-11 s). The maximum alpha-linolenic acid (ALA) content was 33 ± 1%. The highest values of eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) in the microcapsules were 8.4 ± 0.4 and 13 ± 1%, respectively. Fourier transform infrared and X-Ray diffraction analysis results indicated that SDM was successfully formulated with Gum Arabic and maltodextrin (MD). The blending without encapsulation of CSO and FO was digested more efficiently and resulted in more oil being released with simulated gastric fluid (SGF), simulated intestinal fluid (SIF), and SGF + SIF conditions without heating. No significant changes were observed for saturated, monounsaturated, and LCPUFA, whether exposed or not to gastrointestinal conditions. However, compared to the release of SDM, it can be useful for designing delivery systems for the controlled release of essential fatty acids.

Quality Assessment of Fish Oil Obtained after Enzymatic Hydrolysis of a Mixture of Rainbow Trout (Oncorhynchus mykiss) and Atlantic Salmon (Salmo salar) Rest Raw Material Pretreated by High Pressure.

Utilization of fish rest raw material for fish oil extraction has received interest with the increasing demand for sustainable food sources. Enzymatic hydrolysis is an efficient method for the extraction of value-added compounds, but its effectiveness may be enhanced by high-pressure processing (HPP). However, HPP can induce lipid oxidation, affecting the quality of the oil. This study aimed to evaluate the quality of fish oil obtained after enzymatic hydrolysis of a mixture of rainbow trout (Oncorhynchus mykiss) and Atlantic salmon (Salmo salar) rest raw material pretreated by HPP. Six pretreatments were tested prior to enzymatic hydrolysis; 200 MPa × 4 min, 200 MPa × 8 min, 400 MPa × 4 min, 400 MPa × 8 min, 600 MPa × 4 min, and 600 MPa × 8 min. The oil samples were analyzed for lipid oxidation parameters, free fatty acid content, fatty acid composition, and color changes over 8 weeks. The results confirmed that HPP may induce lipid oxidation and revealed significant influence of HPP parameters on lipid oxidation, with higher pressures leading to increased oxidation. Fatty acid composition varied among samples, but it was not substantially affected by HPP.

Reversed-Phase Medium-Pressure Liquid Chromatography Purification of Omega-3 Fatty Acid Ethyl Esters Using AQ-C18.

Omega-3 fatty acids are in high demand due to their efficacy in treating hypertriglyceridemia and preventing cardiovascular diseases. However, the growth of the industry is hampered by low purity and insufficient productivity. This study aims to develop an efficient RP-MPLC purification method for omega-3 fatty acid ethyl esters with high purity and capacity. The results indicate that the AQ-C18 featuring polar end-capped silanol groups outperformed C18 and others in retention time and impurity separation. By injecting pure fish oil esters with a volume equivalent to a 1.25% bed volume on an AQ-C18 MPLC column using a binary isocratic methanol-water (90:10, v:v) mobile phase at 30 mL/min, optimal omega-3 fatty acid ethyl esters were obtained, with the notable purity of 90.34% and a recovery rate of 74.30%. The total content of EPA and DHA produced increased from 67.91% to 85.27%, meeting the acceptance criteria of no less than 84% set by the 2020 edition of the Pharmacopoeia of the People's Republic of China. In contrast, RP-MPLC significantly enhanced the production efficiency per unit output compared to RP-HPLC. This study demonstrates a pioneering approach to producing omega-3 fatty acid ethyl esters with high purity and of greater quantity using AQ-C18 RP-MPLC, showing this method's significant potential for use in industrial-scale manufacturing.

Spray drying the Pickering emulsions stabilized by chitosan/ovalbumin polyelectrolyte complexes for the production of oxidation stable tuna oil microcapsules.

The microencapsulation of polysaturated fatty acids by spray drying remains a challenge due to their susceptibility to oxidation. In this work, antioxidant Pickering emulsions were attempted as feeds to produce oxidation stable tuna oil microcapsules. The results indicated that the association between chitosan (CS) and ovalbumin (OVA) was a feasible way to fabricate antioxidant and wettable complexes and a high CS percentage favored these properties. The particles could yield tuna oil Pickering emulsions with enhanced oxidation stability through high-pressure homogenization, which were successfully spray dried to produce microcapsules with surface oil content of 8.84 % and microencapsulation efficiency of 76.65 %. The microcapsules exhibited significantly improved oxidation stability and their optimum peroxide values after storage at 50 °C, 85 % relative humidity, or natural light for 15 d were 48.67 %, 60.07 %, and 39.69 % respectively lower than the powder derived from the OVA-stabilized emulsion. Hence, Pickering emulsions stabilized by the CS/OVA polyelectrolyte complexes are potential in the production of oxidation stable polyunsaturated fatty acid microcapsules by spray drying.

Preparation of medium- and long-chain triacylglycerols rich in n-3 polyunsaturated fatty acids by bio-imprinted lipase-catalyzed interesterification.

Medium and long-chain triacylglycerol (MLCT) rich in n-3 polyunsaturated fatty acids (PUFAs) were obtained in three-hour interesterification of fish oil with medium-chain triacylglycerol (MCTs), using lipase bio-imprinted with surfactant as a catalyst. Initially, for bio-imprinted lipase preparation, the interesterification reaction conditions were optimized, resulting in a lipase with 1.47 times higher catalytic activity compared to control (non-bio-imprinted). Afterwards, the reaction conditions for MLCT synthesis were optimized, using bio-imprinted lipase as a catalyst. The reaction reached equilibrium within first three hours at 70 °C temperature, 4 wt% lipase load, and molar ratio of substrate 1:1.5. Under these conditions, final product contained 18.52% MCT, 56.65% MLCT, and 24.83% long-chain triacylglycerol (LCT). To reduce the MCT content, a solvent extraction process was performed, yielding 2.42% MCT, 56.19% MLCT, and 41.39% LCT. The obtained structured lipids (SLs), enriched in n-3 PUFAs, offer significant health benefits, enhanced bioavailability, with potential applications in functional foods and nutraceuticals.

Hyaluronic acid-poly(glyceryl)10-stearate nanoemulsion for co-delivery of fish oil and resveratrol: Enhancing bioaccessibility and antioxidant potency.

Hyaluronic acid (HA), an endogenous polysaccharide comprising alternating D-glucuronic acid and N-acetylglucosamine units, is renowned for its high hydrophilicity, biocompatibility, and biodegradability. These attributes have rendered HA invaluable across medical and drug delivery fields. HA can be altered through physical, chemical, or enzymatic methods to improve the properties of the modified substances. In this work, we synthesized a derivative via the esterification of HA with poly(glyceryl)10-stearate (PG10-C18), designated as HA-PG10-C18. This novel derivative was employed to fabricate a nano co-delivery system (HA-PG10-C18@Res-NE) for fish oil and resveratrol (Res), aiming to enhance their stability and bioaccessibility. An exhaustive investigation of HA-PG10-C18@Res-NE revealed that the HA-modified system displayed superior physicochemical stability, notably in withstanding oxidation and neutralizing free radicals. Moreover, in vitro simulated digestion underscored the system's enhanced bioaccessibility of Res and more efficient release of free fatty acids. These outcomes underscore the strategic advantage of HA in modifying PG10-C18 for nanoemulsion formulation. Consequently, HA-PG10-C18 stands as a promising emulsifier for encapsulating lipophilic bioactives in functional foods, nutraceuticals, and pharmaceuticals.

Production of Omega-3 Fatty Acid Concentrates from Common Kilka Oil: Optimization of the Urea Complexation Process.

There has been an increase in interest in the application of ω-3 PUFAs, especially EPA and DHA, in the development of various food products owing to their myriad health benefits. However, most fish oils do not contain more than 30% combined levels of EPA and DHA. In this study, through the urea complexation procedure, the production of EPA and DHA concentrate in their free fatty acids (FFAs) form was achieved from an enzymatic oil extracted from common kilka (Clupeonella cultriventris caspia). To gain the maximum value of EPA and DHA, the response surface methodology (RSM), which is an effective tool to categorize the level of independent variables onto the responses of an experimental process, was also used. Different variables including the urea-fatty acids (FAs) ratio (in the range of 2-6, w/w), the temperature of crystallization (in the range of -24-8 °C), and the time of crystallization (in the range of 8-40 h) were investigated by response surface methodology (RSM) for maximizing the EPA and DHA contents. Following the model validation, the levels of the variables at which the maximum desirability function (0.907 score) was obtained for response variables were 5:1 (urea-FAs ratio), -9 °C (the temperature of crystallization), and 24 h (the time of crystallization). Under these optimal conditions, increases of 2.2 and 4.4 times in the EPA and DHA concentrations were observed, respectively, and an increase in the concentrations of EPA and DHA from 5.39 and 13.32% in the crude oil to 12.07 and 58.36% in the ω-3 PUFA concentrates were observed, respectively. These findings indicate that the urea complexation process is efficient at optimizated conditions.

Tilapia head gelatins to stabilize fish oil emulsions and the effect of extraction methods.

The preparation and use of gelatins from fish by-products have attracted much attention in the field of food science. Herein, four types of tilapia head gelatins were extracted and characterized: hot water-pretreated gelatin (HWG), acetic acid-pretreated gelatin (AAG), sodium hydroxide-pretreated gelatin (SHG), and pepsin enzyme-pretreated gelatin (PEG). The gel strength values followed the order: PEG (74 ± 1 Bloom) > AAG (66 ± 1) > HWG (59 ± 1) > SHG (34 ± 1). The foaming properties, fish oil emulsion viscosity, emulsion activity, and emulsion stabilization ability followed this order: PEG > HWG ≥ AAG > SHG. The effect mechanisms of extraction methods and gelatin concentrations on the emulsion stability involved the interfacial tension, emulsion viscosity, and fat-binding capacity. This work provided important knowledge for analyzing the relations between the structure and function of gelatin. It also provided a high-value application method of fish wastes.

Salt reduction in myofibrillar protein gel via inhomogeneous distribution of sodium-containing encapsulated fish oil coacervate: Mucopenetration ability of sodium carboxymethyl cellulose.

The potential application of fish oil microcapsules as salt reduction strategies in low-salt myofibrillar protein (MP) gel was investigated by employing soy protein isolates/carboxymethyl cellulose sodium (SPI-CMC) coacervates enriched with 25 mM sodium chloride and exploring their rheological characteristics, taste perception, and microstructure. The results revealed that the SPI-CMC coacervate phase exhibited the highest sodium content under 25 mM sodium level, albeit with uneven distribution. Notably, the hydrophilic and adhesive properties of CMC to sodium facilitated the in vitro release of sodium during oral digestion, as evidenced by the excellent wettability and mucopenetration ability of CMC. Remarkably, the fish oil microcapsules incorporating SPI-CMC as the wall material, prepared at pH 3.5 with a core-to-wall ratio of 1:1, demonstrated the highest encapsulation efficiency, which was supported by the strong hydrogen bonding. Interestingly, the presence of SPI-CMC coacervates and fish oil microcapsules enhanced the interaction between MPs and strengthened the low-salt MP gel network. Coupled with electronic tongue analysis, the incorporation of fish oil microcapsules slightly exacerbated the non-uniformity of sodium distribution. This ultimately contributed to an enhanced perception of saltiness, richness, and aftertaste in low-salt protein gels. Overall, the incorporation of fish oil microcapsules emerged as an effective salt reduction strategy in low-salt MP gel.

Microencapsulation of fish oil by spray drying, spray freeze-drying, freeze-drying, and microwave freeze-drying: Microcapsule characterization and storage stability.

The objective of this paper was to evaluate the effect of spray drying (SD), spray freeze-drying (SFD), freeze-drying (FD), and microwave freeze-drying (MFD) on the characteristics of fish oil (FO) microcapsules. The physicochemical properties, morphology, fatty acid composition, and stability of the microcapsules were analyzed. The encapsulation efficiencies of microcapsules dried by SD, SFD, FD, and MFD were 86.98%, 77.79%, 63.29%, and 57.89%, respectively. SD microcapsules exhibited superior properties in terms of effective loading capacity, color, and flowability. Conversely, SFD microcapsules demonstrated improved solubility. Microencapsulation positively affected the thermal stability of FO, but the content of unsaturated fatty acids decreased. The findings from the storage experiment indicated that the oxidative stability of SD fish oil microcapsules was marginally lower compared to microcapsules produced through three alternative drying techniques, all of which were based on the FD concept. The comparison of various drying methods and their effects on the quality of FO microcapsules offers valuable insights that can serve as a foundation for the industrial production of high-quality microcapsules.

The effect of fish oil rich in cetoleic acid on the omega-3 index and skin quality.

OBJECTIVE: The objective of the study was to provide preliminary data on the effect of a long chain monounsaturated oil rich in cetoleic acid on the omega-3 index, a validated measure of EPA and DHA in blood cells, as well as a potential effect of the oil on skin quality. DESIGN: Two intervention studies were performed, each as double blinded, placebo controlled, randomised nutritional trials. The CetoIndex study (N = 55) measured omega-3 index using a blood spot collection kit (Omegaquant). The Optihud study (N = 28) measured skin quality parameters in healthy women using the VISIA system. The cetoleic-rich-oil (CRO) was an oil derived from North Atlantic fish with a predominance of long chain mono-unsaturated fatty acids including cetoleic acid (C22:1 n-11) and gondoic acid (C20:1 n-9). RESULTS: In a placebo-controlled study, the omega-3 index in healthy volunteers was increased similar to that seen with an oil with higher levels of omega-3 fatty acids. In a separate placebo-controlled study, the CRO reduced erythema in skin, which is a marker of inflammation. CONCLUSIONS: The results of this pilot study suggest that the use of a CRO increases the omega-3 index more than expected from the levels of EPA and DHA in the oil. The CRO may potentially have benefits on skin inflammation. SUMMARY: Long chain polyunsaturated fatty acids (LCPUFA), particularly eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), are commonly taken as dietary supplements for a range of health benefits. Other marine fatty acids may also provide health benefits and it is of interest to understand their activity. Long chain mono-unsaturated fatty acids (LCMUFA) have shown biological activity in studies of metabolic health in animal models. Here, we report two intervention studies using a fish oil with a high LCMUFA content where cetoleic acid is the predominant fatty acid (Cetoleic rich oil: CRO). In CetoIndex, a placebo-controlled study in 55 healthy volunteers, the omega-3 index increased similarly to that seen with an oil containing higher levels of omega-3 fatty acids. In Optihud, a placebo-controlled study in 28 female volunteers, the CRO reduced erythema in skin, which is a marker of inflammation. The results of this pilot study support the use of a CRO for increasing the omega-3 index with potential benefits on skin inflammation.

Integrated Process for Schizochytrium Oil Extraction, Enzymatic Modification of Lipids and Concentration of DHA Fatty Acid Esters Using Alternative Methodologies.

Marine microalgae Schizochytrium sp. have a high content of docosahexaenoic acid (DHA), an omega-3 fatty acid that is attracting interest since it prevents certain neurodegenerative diseases. The obtention of a bioactive and purified DHA fatty acid ester using a whole-integrated process in which renewable sources and alternative methodologies are employed is the aim of this study. For this reason, lyophilized Schizochytrium biomass was used as an alternative to fish oil, and advanced extraction techniques as well as enzymatic modification were studied. Microalgal oil extraction was optimized via a surface-response method using pressurized liquid extraction (PLE) obtaining high oil yields (29.06 ± 0.12%) with a high concentration of DHA (51.15 ± 0.72%). Then, the enzymatic modification of Schizochytrium oil was developed by ethanolysis using immobilized Candida antarctica B lipase (Novozym® 435) at two reaction temperatures and different enzymatic loads. The best condition (40 °C and 200 mg of lipase) produced the highest yield of fatty acid ethyl ester (FAEE) (100%) after 8 h of a reaction attaining a cost-effective and alternative process. Finally, an enriched and purified fraction containing DHA-FAEE was obtained using open-column chromatography with a remarkably high concentration of 93.2 ± 1.3% DHA. The purified and bioactive molecules obtained in this study can be used as nutraceutical and active pharmaceutical intermediates of marine origin.

Enzymatic Preparation, In-Depth Molecular Analysis, and In Vitro Digestion Simulation of Palmitoleic Acid (ω-7)-Enriched Fish Oil Triacylglycerols.

In this study, an enzymatic reaction was developed for synthesizing pure triacylglycerols (TAG) with a high content of palmitoleic acid (POA) using fish byproduct oil. The characteristics of synthesized structural TAGs rich in POA (POA-TAG) were analyzed in detail through ultrahigh-performance liquid chromatography Q Exactive orbitrap mass spectrometry. Optimal conditions were thoroughly investigated and determined for reaction systems, including the use of Lipozyme TL IM and Novozym 435, 15 wt % lipase loading, substrate mass ratio of 1:3, and water content of 2.5 and 0.5 wt %, respectively, resulting in yields of 67.50 and 67.45% for POA-TAG, respectively. Multivariate statistical analysis revealed that TAG 16:1/16:1/20:4, TAG 16:1/16:1/16:1, TAG 16:1/16:1/18:1, and TAG 16:0/16:1/18:1 were the main variables in Lipozyme TL IM and Novozym 435 enzyme-catalyzed products under different water content conditions. Finally, the fate of POA-TAG across the gastrointestinal tract was simulated using an in vitro digestion model. The results showed that the maximum release of free fatty acids and apparent rate constants were 71.44% and 0.0347 s-1, respectively, for POA-TAG lipids, and the physical and structural characteristics during digestion depended on their microenvironments. These findings provide a theoretical basis for studying the rational design of POA-structural lipids and exploring the nutritional and functional benefits of POA products.

Enzymatically produced acylglycerol and glycerin monostearate additives improved the characteristics of gelatin-stabilized omega-3 emulsions and microcapsules.

The impacts of enzymatically produced acylglycerol and glycerin monostearate on the characteristics of gelatin-stabilized omega-3 emulsions and microcapsules were investigated. Tuna oil was enzymatically produced and the resulting acylglycerol was mixed with tuna oil at 12.5% (w/w) to prepare a novel oil phase. This oil phase was stabilized by gelatin to prepare oil-in-water emulsions and subsequent microcapsules via complex coacervation. The tuna oil with glycerin monostearate (GMS) at 1 and 2% (w/w) were used as controls. Results showed that both acylglycerol and GMS significantly reduced the emulsion droplet size and zeta potential, while increasing the viscoelasticity and stability. The diacylglycerol/monoacylglycerol were involved in the oil/water interfacial layer formation by lowering interfacial tension and increasing droplet surface hydrophobicity. Overall, the changed emulsion properties promoted the complex coacervation and contributed to the formation of microcapsules with improved oxidative stability. Therefore, enzymatically produced acylglycerol can develop high-quality stable omega-3 microencapsulated novel food ingredients.

Fish oil-loaded multicore submillimeter-sized capsules prepared with monoaxial electrospraying, chitosan-tripolyphosphate ionotropic gelation, and Tween blending.

In order to load fish oil for potential encapsulation of fat-soluble functional active substances, fish oil-loaded multicore submillimeter-sized capsules were prepared with a combination method of three strategies (monoaxial electrospraying, chitosan-tripolyphosphate ionotropic gelation, and Tween blending). The chitosan-tripolyphosphate/Tween (20, 40, 60, and 80) capsules had smaller and evener fish oil cores than the chitosan-tripolyphosphate capsules, which resulted from that Tween addition induced smaller and evener fish oil droplets in the emulsions. Tween addition decreased the water contents from 56.6 % to 35.0 %-43.4 %, increased the loading capacities from 10.4 % to 12.7 %-17.2 %, and increased encapsulation efficiencies from 97.4 % to 97.8 %-99.1 %. In addition, Tween addition also decreased the highest peroxide values from 417 meq/kg oil to 173-262 meq/kg oil. These properties' changes might result from the structural differences between the chitosan-tripolyphosphate and chitosan-tripolyphosphate/Tween capsules. All the results suggested that the obtained chitosan-tripolyphosphate/Tween capsules are promising carriers for fish oil encapsulation. This work also provided useful knowledge to understand the preparation, structural, and physicochemical properties of the chitosan-tripolyphosphate capsules.

Molecular modification of low-dissolution soy protein isolates by anionic xanthan gum, neutral guar gum, or neutral konjac glucomannan to improve the protein dissolution and stabilize fish oil emulsion.

Herein, the effects of anionic xanthan gum (XG), neutral guar gum (GG), and neutral konjac glucomannan (KGM) on the dissolution, physicochemical properties, and emulsion stabilization ability of soy protein isolate (SPI)-polysaccharide conjugates were studied. The SPI-polysaccharide conjugates had better water dissolution than the insoluble SPI. Compared with SPI, SPI-polysaccharide conjugates had lower ß-sheet (39.6 %-56.4 % vs. 47.3 %) and α-helix (13.0 %-13.2 % vs. 22.6 %) percentages, and higher ß-turn (23.8 %-26.5 % vs. 11.0 %) percentages. The creaming stability of SPI-polysaccharide conjugate-stabilized fish oil-loaded emulsions mainly depended on polysaccharide type: SPI-XG (Creaming index: 0) > SPI-GG (Creaming index: 8.1 %-21.2 %) > SPI-KGM (18.1 %-40.4 %). In addition, it also depended on the SPI preparation concentrations, glycation times, and glycation pH. The modification by anionic XG induced no obvious emulsion creaming even after 14-day storage, which suggested that anionic polysaccharide might be the best polysaccharide to modify SPI for emulsion stabilization. This work provided useful information to modify insoluble proteins by polysaccharides for potential application.

Molecular phylogenetics of the Umbelopsis genus-identification of new species and evaluation of their oil application value.

AIMS: The aim of this study was to reconstruct the evolutionary framework of the genus Umbelopsis by using modern taxonomic strategies and evaluating the quality of oil and prospective uses of three distinct species. METHODS AND RESULTS: Three species of Umbelopsis were identified based on morphological characteristics and phylogenetic evidence obtained from three genes (ITS, LSU, and ACT). A new species of Umbelopsis was described and illustrated, and subsequently named U. ophiocordycipiticola. The characteristics of U. ophiocordycipiticola exhibited sporangia with a diameter ranging from 8 to 17 µm. and sporangiospores that were oval to ellipsoidal in shape, irregularly angular, with dimensions of ∼1.9-2.9 × 1.7-3.0 µm. Gas chromatography and mass spectrometry (GC-MS) were used to examine the composition of fatty acids. Notably, U. ophiocordycipiticola showed a significantly higher oil content of 50.89% in dry cell weight (DCW) compared to U. vinacea and U. ramanniana. The mean proportion of polyunsaturated fatty acids (PUFAs) in U. ophiocordycipiticola was 32.38%, and the maximum levels of γ-linolenic acid (GLA), arachidonic acid (ARA), eicosapentaenoic acid (EPA), and docosahexaenoic acid (DHA) in U. ophiocordycipiticola were found to be 14.51, 0.24, 0.54, and 0.53%, respectively. The biodiesel quality from all three species complied with applicable standards set by the American Association for Testing and Materials (ASTM 6751) and the Brazilian National Petroleum Agency (ANP 255). CONCLUSIONS: The establishment of a novel species, U. ophiocordycipiticola, was strongly supported by morphological and molecular evidence. Umbelopsis ophiocordycipiticola exhibited a high-value PUFA content. Additionally, three Umbelopsis species demonstrated good quality for biodiesel production.

Subcritical water-assisted fish gelatin hydrolysis for astaxanthin-loaded fish oil emulsion stability.

Though gelatin emulsifying properties have been intensively studied, how low-molecular-weight (LMW) fish gelatin affects astaxanthin (AST)-loaded fish oil emulsion stability remains elusive. In this study, subcritical water hydrolysis (SWH)-modified LMW fish gelatin (SWHG) was produced from 110 °C to 180 °C and used to enhance the AST steadiness in oil/water emulsions in the presence of an emulsifier, lecithin. In the prepared emulsions, the surface charge increased while droplet size decreased with the decrease in gelatin MW due to the reduced thickness of the adsorbed gelatin membrane. LMW gelatin and lecithin could form a firm-absorbed layer on the droplet surface by electrostatic interaction between amide groups of gelatin molecules and phosphate groups of lecithin, thus stabilizing the emulsions. SWHG improved the creaming stability of the emulsions and hindered the oxygen- and light-induced AST degradation for 11 months compared to high MW gelatin. Whereas, the control emulsion showed noticeable phase separation after two weeks of storage. These findings prove the advantage of the SWH approach and propose the use of SWHG in oil-in-water emulsions for AST stabilization.

Inhibition performance of almond shell hydrochar-based fish oil emulsion gel on Klebsiella pneumonia inoculated fish skin and its characteristics.

In this study, the inhibition potential against Klebsiella pneumoniae (K. pneumoniae) and the characterization of fish oil (FO) emulsion gel (EGE) containing almond shell hydrochar (AH) were investigated. Oily water of mullet liver was emulsified using tween 80, then gelled using gelatin and finally immobilized into hydrochar using an ultrasonic homogenizer. Characteristics and surface analysis of hydrochar-based emulsion gel (HEGE) were examined using FTIR and SEM. Stability, particle size distribution and zeta potential of HEGE were measured. In this study, a zeta potential of -18.46 indicated that HEGE was more stable than EGE (35.7 mV). The addition of hydrochar to the emulsion gel containing micro-droplets enabled the structure to become fully layered and stable. Time-dependent inactivation of K. pneumoniae exposed to HEGE and fixed in 6 mm-fish skin was evaluated for the first time in this study. While the highest log reduction and percent reduction in the bacterial count were achieved within 5 min with 0.87 CFU/cm2 and 86.60% with EGE, the lowest log reduction and percent reduction were achieved with 0.003 CFU/cm2 and 0.082% with HEGE in 30 min. In conclusion, the almond shell hydrochar-immobilized emulsion gel is a functional adsorbent that can inhibit K. pneumonia, and its stability and performance make it a unique candidate for further studies in this field.

High-pressure microfluidization enhanced the stability of sodium caseinate-EGCG complex-stabilized fish oil emulsion.

Improving the emulsion-stabilizing effect of protein by chemical or physical modification has been paid much attention recently. Here, sodium caseinate (CS) was treated by high-pressure-microfluidization (HPM) under 0-100 MPa, and was further complexed with (-)-epigallocatechin-3-gallate (EGCG) to form an excellent emulsifier that stabilized fish oil emulsions. Results showed that HPM treatment (especially 80 MPa) significantly changed the secondary structure of CS, and 80 MPa-PCS-EGCG had the best emulsifying and antioxidant activities. In addition, after HPM treatment and EGCG bonding, CS formed a thicker interface layer on the surface of oil droplets, which could better protect the fish oil from the influence by oxygen, temperature and ion concentration. Moreover, the fish oil emulsion stabilized by PCS-EGCG complex significantly delayed the release of free fatty acids subjected to in vitro digestion. Conclusively, HPM-treated CS-EGCG complex could be a potential emulsifier to improve the stability of fish oil emulsions.