Biological impact of lead from halide perovskites reveals the risk of introducing a safe threshold.

Regulations currently in force enable to claim that the lead content in perovskite solar cells is low enough to be safe, or no more dangerous, than other electronics also containing lead. However, the actual environmental impact of lead from perovskite is unknown. Here we show that the lead from perovskite leaking into the ground can enter plants, and consequently the food cycle, ten times more effectively than other lead contaminants already present as the result of the human activities. We further demonstrate that replacing lead with tin represents an environmentally-safer option. Our data suggest that we need to treat the lead from perovskite with exceptional care. In particular, we point out that the safety level for lead content in perovskite-based needs to be lower than other lead-containing electronics. We encourage replacing lead completely with more inert metals to deliver safe perovskite technologies.

Ambient air quality changes after stubble burning in rice-wheat system in an agricultural state of India.

Ground-based ambient air monitoring was conducted to assess the contribution of crop residue burning of wheat (Triticum aestivum) and rice (Oriza sativa) at different locations in three districts (Kaithal, Kurukshetra, and Karnal) of the agricultural state of Haryana in India for two successive years (2016 and 2017). The Air Quality Index (AQI) and concentration of primary pollutants (SOx, NOx, and PM2.5) were determined in rice and wheat crop season, for burning and non-burning periods. During crop residue burning periods, concentrations of SOx, NOx, and PM2.5 were exceeded the NAAQS values by 78%, 71%, and 53%, respectively. A significant increase in SOx (4.5 times), NOx (3.8 times), and PM2.5 concentration (3.5 times) was observed in stubble burning periods as compared to pre-burning (p < 0.05). A positive and significant correlation among the three pollutant concentrations was observed (p < 0.01). The AQI of KA site in Karnal district fell in severely polluted category during 2016 for rice as well as wheat residue burning period, and of KK site in Kaithal during wheat residue burning in year 2017. Results of present study indicate a remarkable increase in pollutant concentration (SOx, NOx, and PM2.5) during the crop residue burning periods. To the best of our knowledge, the outcomes of present study in this region have not been reported in earlier reports. Hence, there is an urgent need to curb air pollution by adopting sustainable harvesting technologies and management of residues.

Contrast agent comparison for three-dimensional micro-CT angiography: A cadaveric study.

Barium sulfate and lead oxide contrast media are frequently used for cadaver-based angiography studies. These contrast media have not previously been compared to determine which is optimal for the visualisation and measurement of blood vessels. In this study, the lower limb vessels of 16 embalmed Wistar rats, and four sets of cannulae of known diameter, were injected with one of three different contrast agents (barium sulfate and resin, barium sulfate and gelatin, and lead oxide combined with milk powder). All were then scanned using micro-computed tomography (CT) angiography and 3-D reconstructions generated. The number of branching generations of the rat lower limb vessels were counted and compared between the contrast agents using ANOVA. The diameter of the contrast-filled cannulae, were measured and used to calculate the accuracy of the measurements by comparing the bias and variance of the estimates. Intra- and inter-observer reliability were calculated using intra-class correlation coefficients. There was no significant difference (mean difference [MD] 0.05; MD 95% confidence interval [CI] -0.83 to 0.93) between the number of branching generations for barium sulfate-resin and lead oxide-milk powder. Barium sulfate-resin demonstrated less bias and less variance of the estimates (MD 0.03; standard deviation [SD] 1.96 mm) compared to lead oxide-milk powder (MD 0.11; SD 1.96 mm) for measurements of contrast-filled cannulae scanned at high resolution. Barium sulfate-resin proved to be more accurate than lead oxide-milk powder for high resolution micro-CT scans and is preferred due to its non-toxicity. This technique could be applied to any embalmed specimen model. Copyright © 2016 John Wiley & Sons, Ltd.

Disinfectants in health care: finding an alternative to chlorine dioxide.

Cleanliness of the clinical environment has a direct impact on healthcare-associated infection (HCAI) incidence and there is increasing evidence of its importance with regard to infection prevention and control. While traditional high-level disinfectants have excellent antimicrobial properties, these are typically offset against issues such as corrosiveness, toxicity, cost and user acceptance. Recent years have seen several user-friendly sporicidal disinfectants emerge onto the market. Antimicrobial profile and user acceptance determine the clinical success of any disinfectant. Therefore, product adoption is often a two-stage process with a tabletop evaluation of the appropriate technical data, including efficacy claims, followed by an in-use product evaluation. The first part of this article demonstrates the importance of the clinical environment with respect to HCAI and examines some of the issues around disinfectants used in health care and considerations when selecting a new disinfectant for use. The second part reports the experiences of the Infection Prevention and Control team at Alder Hey Children's Hospital in their assessment and subsequent adoption of a new user-friendly sporicidal disinfectant into clinical practice.

Magnetic labeling of non-phagocytic adherent cells with iron oxide nanoparticles: a comprehensive study.

Small particles of iron oxide (SPIO) and ultrasmall particles of iron oxide (USPIO), inducing a strong negative contrast on T(2) and T(2)*-weighted MR images, are the most commonly used systems for the magnetic labeling of cultured cells and their subsequent detection by magnetic resonance imaging (MRI). The purpose of this work is to study the influence of iron incubation concentration, nanoparticle size and nanoparticle coating on the magnetic labeling and the viability of non-phagocytic adherent cells in culture. The magnetic labeling of 3T6 fibroblasts was studied by T(2)-weighted MRI at 4.7 T and by dosing-or cytochemical revealing-of iron through methods based on Perl's Prussian blue staining. Cells were incubated for 48 h with increasing iron concentrations of SPIO (25-1000 microg Fe/ml Endorem. Sinerem, a USPIO (20-40 nm) coated with neutral dextran, and Resovist (65 nm), a SPIO bearing an anionic carboxydextran coating, were compared with Endorem (dextran-coated, 80-150 nm) as magnetic tags. The iron loading of marrow stromal cell primary cultures (MSCs) isolated from rat femurs was compared with that of 3T6 fibroblasts. The SPIO-labeling of cells with Endorem was found to be dependent on the iron incubation concentration. MSCs, more sparsely distributed in the culture, exhibited higher iron contents than more densely populated 3T6 fibroblast cultures. A larger iron loading was achieved with Resovist than with Endorem, which in turn was more efficient than Sinerem as a magnetic tag. The magnetic labeling of cultured non-phagocytic adherent cells with iron oxide nanoparticles was thus found to be dependent on the relative concentration of the magnetic tag and of the cells in culture, on the nanoparticle size, and on the coating type. The viability of cells, estimated by methods assessing cell membrane permeability, was not affected by magnetic labeling in the conditions used in this work.

Effect of diode laser irradiation on the apical sealing of MTA retrofillings.

Apical sealing is essential for the success of paraendodontic surgery, so any procedure that may favor an adequate sealing of the apical remainder should be performed. The purpose of this study was to evaluate the influence of diode laser irradiation on the apical sealing of root-end cavities with MTA retrofillings. Root canals in twenty extracted human teeth were shaped with K-files and filled with gutta-percha. The apexes were cut off and root-end preparations were performed. The roots were divided randomly in 2 groups. Group 1 (ten specimens) was retrofilled with MTA. Group 2 was irradiated with diode laser, with 1 W for 20 seconds, on the apical surface and root end cavity before retrofilling with MTA. The specimens had their external surfaces impermeabilized with cyanoacrylate, except for the apical surface, and were then immersed in 1% rhodamine B dye for 72 h and placed in plaster stone. After that, the specimens were submitted to longitudinal abrasion until half of the root remained. The linear dye leakage was observed in these mid-roots between the root canal wall and retrofilling. The linear dye leakage was measured with Image Lab software, and the results were statistically analyzed with Student's t test. There were no statistically significant differences between the two groups (p > 0.05). The diode laser irradiation did not improve the apical sealing of MTA retrofillings under the conditions of this in vitro study.

Effect of different dye solutions on the evaluation of the sealing ability of Mineral Trioxide Aggregate.

Alkaline materials have shown incompatibility with methylene blue dye in leakage experiments. The goal of the present study was to analyze the effect of different dyes on the evaluation of the apical sealing ability of Mineral Trioxide Aggregate root-end fillings. Fifty-six extracted human canines were submitted to root canal instrumentation and obturation. After apical resection, retrograde cavities were prepared and teeth were randomly divided into four experimental (n = 13) and two control groups (n = 2). The following root-end filling materials were used: groups 1 and 2--Pro Root MTA (Dentsply), groups 3 and 4--zinc oxide-eugenol cement (ZOE). Teeth in groups 1 and 3 were immersed in 2% methylene blue solution, while teeth in groups 2 and 4 were immersed in 0.2% rhodamine B in a reduced pressure environment for 48 hours. Teeth were then longitudinally sectioned and leakage was evaluated. Results were submitted to statistical analysis (ANOVA and Tukey's test). Group 1 presented the least leakage (p < 0.05). It was concluded that the evaluation of the sealing ability of MTA is influenced by the dye used, since this material presented better sealing ability when evaluated with Methylene Blue, but was similar to ZOE when evaluated with rhodamine B.

Comparison of the cytotoxicity of the MEIC reference chemicals measured in protein free and in complete culture medium.

In order to investigate if a protein free cytotoxicity assay could improve the prediction of human acute toxicity, the cytotoxicity of 40 MEIC reference chemicals was measured by the neutral red uptake inhibition after 24h in protein free culture medium on rat hepatoma-derived Fa32 cells. The results were compared with the corresponding values obtained in complete culture medium, including 10% fetal calf serum. Potassium cyanide, arsenic trioxide, mercuric chloride, hexachlorophene and pentachlorophenol were much more cytotoxic in PF medium, as was the case to a lower extent for 16 other chemicals. The cytotoxicity of 8 chemicals was only changed to a limited extent when tested in PF medium, suggesting that serum proteins do not strongly interact with their cytotoxicity. Eleven other chemicals were less cytotoxic in PF medium, maybe because of too poor physiological conditions. Although a large number of differences in cytotoxicity were observed in function of the medium used for the assay, a good correlation was observed between both series of data (r(2)=0.946). The correlation between the cytotoxicity in PF medium and the human acute toxicity is lower (r(2)=0.647) than that in complete medium (r(2)=0.746). The results show that further research is necessary in order to improve the in vitro/in vivo correlations by introducing protein-dependent considerations.

Effect of different dye solutions on the evaluation of the sealing ability of mineral trioxide aggregate

Tem sido demonstrada a incompatibilidade de materiais alcalinos com a solucão corante de azul de metileno utilizada em testes de infiltracão marginal. O objetivo do presente estudo foi analisar a influência de diferentes solucões corantes na avaliacão do selamento apical proporcionado pelo agregado de trióxido mineral. Cinqüenta e seis caninos humanos extraídos tiveram seus canais radiculares instrumentados e obturados. Após a seccão da porcão apical, cavidades retrógradas foram preparadas e os dentes divididos aleatoriamente em quatro grupos experimentais (n = 13) e dois controles (n = 2). Foram utilizados os seguintes materiais retrobturadores: grupos 1 e 2 - Pro Root MTA (Dentsply); grupos 3 e 4 - cimento de óxido de zinco e eugenol (OZE). Em seguida, os dentes dos grupos 1 e 3 foram imersos em solucão de Azul de Metileno a 2% e dos grupos 2 e 4 em solucão de Rodamina B a 0,2% por 48 horas em ambiente com vácuo. Decorrido este período, os dentes foram seccionados longitudinalmente, e a infiltracão marginal foi analisada. Os dados obtidos foram submetidos à análise estatística (Análise de variância e teste de Tukey). Os resultados demonstraram que o Grupo 1 apresentou menor infiltracão apical que os demais (p < 0,05). Conclui-se que a avaliacão da capacidade seladora do MTA é influenciada pela solucão corante, uma vez que o mesmo apresentou melhores resultados com o Azul de Metileno e infiltracão marginal semelhante à do OZE quando avaliado em solucão de Rodamina B.

[Determination of trace zirconium and hafniumin sample by atomic emission spectrometry].

This paper describes the determination of trace Zr and Hf in the sample using carbon powder and titanium oxide as the buffer by Atomic Emission Spectrometry (AES). Titanium was selected for the internal standard line. Sample separation and chemical treatment were not required. The sample was directly loaded into an ordinary electrode. The method is simple, rapid and accurate. The conditions for the determination, and the factors of influence have been studied. A new method has been developed for the determination of zirconium and hafnium. The analytical lines of Zr and Hf were 327.3 and 286.6 nm respectively. The internal standard line of Ti was 308.8 nm. The linear range of the determination of Zr and Hf was 0-0.50% and 0-0.25% respectively. The detection limit of Zr and Hf was 0.0010% and 0.010% respectively. The range of the recovery of zirconium and hafnium was 96.67%-105.0%. The results for these elements in standard sample are in agreement with certified values with a precision of 3.61% RSD for Zr (n = 9), and 4.82% RSD for Hf (n = 9). The method has been applied to the determination of Zr and Hf with satisfactory results.

Sealing ability of MTA, Super EBA, Vitremer and amalgam as root-end filling materials

Este estudo avaliou a capacidade de selamento do agregado trióxido mineral (MTA Angelus), de um cimento de óxido de zinco e eugenol reforçado (Super EBA), de um cimento de ionômero de vidro reforçado por resina (Vitremer) e de um amálgama sem zinco (GS-80) (controle). Os canais radiculares de oitenta molares inferiores humanos foram acessados, limpos, modelados e obturados. Os ápices foram seccionados, e as cavidades, preparadas. Os dentes foram divididos em 4 grupos de 40 cavidades, retrobturados com os materiais e imersos em azul de metileno por 72 h a 37ºC. As raízes foram então seccionadas transversalmente a cada milímetro e avaliadas sob aumento, observando-se a penetração de corante a cada corte. Os dados foram avaliados usando-se o teste de Kruskal-Wallis (5%), que mostrou diferenças entre todos os materiais (p < 0,001). A ordem crescente de infiltração marginal foi MTA < Vitremer < Super EBA < amálgama. Níveis mais altos de infiltração foram observados nos cortes de primeiro milímetro de amálgama, Vitremer e MTA, quando comparados com o terceiro milímetro (p < 0,05).

A 17-month evaluation of a chlorine dioxide water treatment system to control Legionella species in a hospital water supply.

OBJECTIVE: To assess the safety and efficacy of a chlorine dioxide water treatment system in controlling Legionella in a hospital water supply. DESIGN: For 17 months following installation of the system, we performed regular water cultures throughout the building, assessed chlorine dioxide and chlorite levels, and monitored metal corrosion. RESULTS: Sites that grew Legionella species decreased from 41% at baseline to 4% (P = .001). L. anisa was the only species recovered and it was found in samples of both hot and cold water. Levels of chlorine dioxide and chlorite were below Environmental Protection Agency (EPA) limits for these chemicals in potable water. Further, enhanced carbon filtration effectively removed the chemicals, even at chlorine dioxide levels of more than twice what was used to treat the water. After 9 months, corrosion of copper test strips exposed to the chlorine dioxide was not higher than that of control strips. During the evaluation period, there were no cases of nosocomial Legionella in the building with the system, whereas there was one case in another building. CONCLUSIONS: Our results indicate that operation of a chlorine dioxide system effectively removed Legionella species from a hospital water supply. Furthermore, we found that the system was safe, as levels of chlorine dioxide and chlorite were below EPA limits. The system did not appear to cause increased corrosion of copper pipes. Our results indicate that chlorine dioxide may hold promise as a solution to the problem of Legionella contamination of hospital water supplies.

Arsenic trioxide (trisenox) therapy for acute promyelocytic leukemia in the setting of hematopoietic stem cell transplantation.

The relapse-free survival of patients with acute promyelocytic leukemia (APL) has significantly increased during the last decade. The introduction of all-trans retinoic acid (ATRA) doubled the survival of patients with this disease. However, despite ATRA and anthracycline-based chemotherapy, 12%-30% of patients will still relapse. Arsenic trioxide (ATO) has demonstrated efficacy and safety in patients with first and subsequent relapsed or refractory APL, regardless of the disease-free interval. Treatment of relapsed and refractory patients with this novel therapy produces complete remission in 87% of patients and molecular remission in 83%. Studies have documented the efficacy of autologous and allogeneic transplantation as salvage therapy in relapsed and refractory APL. The introduction of ATO into the treatment regimen for APL has stimulated discussion on its role in the transplantation setting. Investigators recently met to discuss the issue and make recommendations regarding ATO therapy in patients who are in their second or subsequent complete remission and are candidates for transplantation. This article describes the pivotal studies of this novel agent, discusses risk factor stratification for relapse in patients with APL, and proposes protocols for treatment incorporating ATO therapy. In addition, it describes scientific issues in ongoing and proposed clinical trials of ATO therapy for this disease.

An evaluation of the use of chlorine dioxide (Tristel One-Shot) in an automated washer/disinfector (Medivator) fitted with a chlorine dioxide generator for decontamination of flexible endoscopes.

Microbiological tests were carried out to evaluate a new chlorine dioxide sterilant: Tristel OneShot. Preliminary in vitro suspension tests showed that solutions containing around 140 ppm chlorine dioxide achieved a reduction factor exceeding 10(6) of Staphylococcus aureus in 1min and of Bacillus subtilis spores in 2.5 min in the presence of 3g/L bovine albumin. Subsequent tests evaluated the effectiveness of Tristel One-Shot in a Medivator washer/disinfector fitted with a Tristel Generator for processing flexible endoscopes. Each test run involved three stages. In the first, the instrument and air-water channels of a gastroscope were inoculated with a suspension of Pseudomonas aeruginosa (10(8)cfu/ml) in 10% sodium glutamate and serum (0, 5 or 10%) and then drained, partially dried, and saline flushed through for total viable counts (TVCs). In the second stage, the channels were re-inoculated with test organisms; detergent was flushed through the channels which were then brushed; and saline was flushed through for TVCs. In the third stage, the channels were re-inoculated; detergent was flushed through the channels which were then brushed; the endoscope was processed in the Medivator; and saline was flushed through for TVCs. Carrying out all three stages enabled determination of (1) the contribution played by manual cleaning of channels prior to processing in the Medivator, and (2) the combined effect of manual cleaning followed by processing. Two series of test runs were done. In the first, the Tristel Generator was set to generate 230ppm chlorine dioxide, and in the second 150ppm. In the first, cleaning followed by processing in the Medivator consistently achieved a >/= 10(6)-fold reduction of test organisms, and in the second a >/= 10(5)-fold reduction. Pre-cleaning of channels was very important-when done the initial concentration of serum in the inoculum (0-10%) had no affect on the results obtained after processing.

[Toxicological characteristics and standardization of various poly-metallic oxides]. / Toksikologicheskaia kharakteristika i reglamentatsiia riada polimetallicheskikh oksidov.

Acute toxicity, functional cumulative and local effects of the four ++poly-metallic oxides YBa2Cu3O7, Bi4Sr3O16, Tl2Ca2Cu3O10, Lao,7Sro,3CoO3, were studied in laboratory animals. Parallel experiments on assessment toxicity of the regular oxides of the studied metals in mice were carried out. The major dissolution of metals was shown to occur in acid medium. Thallium-barium-calcium cuprite turned out to be the most toxic and cumulative; it induced the most severe morphologic changes in the liver and kidneys. The least severe disorders caused by this substance were in the rat gastric mucosa and in rabbit eye after a conjunctival injection. Yttrium-barium cuprite induced the most severe changes at the site of injection, lanthanum-strontium cobaltite ranks second here. All copper-containing polymetallic oxides show resorptive toxicity when applied to the skin. Different types of combined toxicity are possible, that is why MACs for the regular oxides can not be used for setting the normal concentrations of ++poly-metallic oxides in air. Estimated toxicometric parameters helped to score the concentrations, which may serve as tentative safe levels of the studies substances.