Effects of hydrogen permeation on the mechanical characteristics of electroless nickel-plated free-cutting steel for application to the hydrogen valves of hydrogen fuel cell electric vehicles.

Electroless nickel plating is a suitable technology for the hydrogen industry because electroless nickel can be mass-produced at a low cost. Investigating in a complex environment where hydrogen permeation and friction/wear work simultaneously is necessary to apply it to hydrogen valves for hydrogen fuel cell vehicles. In this research, the effects of hydrogen permeation on the mechanical characteristics of electroless nickel-plated free-cutting steel (SUM 24L) were investigated. Due to the inherent characteristics of electroless nickel plating, the damage (cracks and delamination of grain) and micro-particles by hydrogen permeation were clearly observed at the grain boundaries and triple junctions. In particular, the cracks grew from grain boundary toward the intergranualr. This is because the grain boundaries and triple junctions are hydrogen permeation pathways and increasing area of the hydrogen partial pressure. As a result, its surface roughness increased by a maximum of two times, and its hardness and adhesion strength decreased by hydrogen permeation. In particular, hydrogen permeation increased the friction coefficient of the electroless nickel-plated layer, and the damage caused by adhesive wear was significantly greater, increasing the wear depth by up to 5.7 times. This is believed to be due to the decreasing in wear resistance of the electroless nickel plating layer damaged by hydrogen permeation. Nevertheless, the Vickers hardness and the friction coefficient of the electroless nickel plating layer were improved by about 3 and 5.6 times, respectively, compared with those of the free-cutting steel. In particular, the electroless nickel-plated specimens with hydrogen embrittlement exhibited significantly better mechanical characteristics and wear resistance than the free-cutting steel.

Numerical investigation of fluid flow behavior in steel cord with lattice Boltzmann methodology: The impacts of microstructure and loading force.

Steel cord materials were found to have internal porous microstructures and complex fluid flow properties. However, current studies have rarely reported the transport behavior of steel cord materials from a microscopic viewpoint. The computed tomography (CT) scanning technology and lattice Boltzmann method (LBM) were used in this study to reconstruct and compare the real three-dimensional (3D) pore structures and fluid flow in the original and tensile (by loading 800 N force) steel cord samples. The pore-scale LBM results showed that fluid velocities increased as displacement differential pressure increased in both the original and tensile steel cord samples, but with two different critical values of 3.3273 Pa and 2.6122 Pa, respectively. The original steel cord sample had higher maximal and average seepage velocities at the 1/2 sections of 3D construction images than the tensile steel cord sample. These phenomena should be attributed to the fact that when the original steel cord sample was stretched, its porosity decreased, pore radius increased, flow channel connectivity improved, and thus flow velocity increased. Moreover, when the internal porosity of tensile steel cord sample was increased by 1 time, lead the maximum velocity to increase by 1.52 times, and the average velocity was increased by 1.66 times. Furthermore, when the density range was determined to be 0-38, the pore phase showed the best consistency with the segmentation area. Depending on the Zou-He Boundary and Regularized Boundary, the relative error of simulated average velocities was only 0.2602 percent.

A Comprehensive Evaluation of Dioxins and Furans Occurrence in River Sediments from a Secondary Steel Recycling Craft Village in Northern Vietnam.

This first study investigated the presence of dioxins and furans in river sediments around a craft village in Vietnam, focusing on Secondary Steel Recycling. Sediment samples were collected from various locations along the riverbed near the Da Hoi Secondary Steel Recycling village in Bac Ninh province. The analysis was conducted using a HRGC/HRMS-DFS device, detecting a total of 17 dioxin/furan isomers in all samples, with an average total concentration of 288.86 ng/kg d.w. The concentrations of dioxin/furan congeners showed minimal variation among sediment samples, ranging from 253.9 to 344.2 ng/kg d.w. The predominant compounds in the dioxin group were OCDD, while in the furan group, they were 1,2,3,4,6,7,8-HpCDF and OCDF. The chlorine content in the molecule appeared to be closely related to the concentration of dioxins and their percentage distribution. However, the levels of furan isomers did not vary significantly. The distribution of these compounds was not dependent on the flow direction, as they were mainly found in solid waste and are not water-soluble. Although the hepta and octa congeners had high concentrations, when converted to TEQ values, the tetra and penta groups (for dioxins) and the penta and hexa groups (for furans) contributed more to toxicity. Furthermore, the source of dioxins in sediments at Da Hoi does not only originate from steel recycling production activities but also from other combustion sites. The average total toxicity was 10.92 ng TEQ/kg d.w, ranging from 4.99 to 17.88 ng TEQ/kg d.w, which did not exceed the threshold specified in QCVN 43:2017/BTNMT, the National Technical Regulation on Sediment Quality. Nonetheless, these levels are still concerning. The presence of these toxic substances not only impacts aquatic organisms in the sampled water environment but also poses potential health risks to residents living nearby.

Accelerated corrosion of low carbon steel by oscillatory acidic streams generated with a bio-inspired claw device.

A mechanical device inspired by the pistol shrimp snapper claw was developed. This technology features a claw characterized by a periodic opening/closing motion, at a controlled frequency, capable of producing oscillating flows at transitional Reynolds numbers. An innovative method was also proposed for determining the corrosion rate of carbon steel samples under oscillating acidic streams (aqueous solution of HCl). By employing very-thin carbon steel specimens (25 µm thickness), with one side coated with Zn and not exposed to the stream, it became possible to electrochemically sense the Zn surface once the steel sample was perforated, thus providing the average dissolution rate into the most relevant pit on the steel surface. Furthermore, a laser light positioned beneath the metallic sample, along with a camera programmed to periodically capture images of the steel surface, facilitated the accurate counting of the number of newly formed pits. The system consisting of the thin steel sample and the Zn coating can be seen as a type of corrosion sensor. Furthermore, the proposed laser illumination method allows corroborating the electrochemical detection of pits and also establishing their location. The techniques crafted in this study pave the way for developing alternative corrosion sensors that boast appealing attributes: affordability, compactness, and acceptable accuracy to detect in time and space localized damage.

Zwitterion modified chitosan as a high-performance corrosion inhibitor for mild steel in hydrochloric acid solution.

Herein, a novel chitosan Schiff base (CS-FGA) as a sustainable corrosion inhibitor has been successfully synthesized via a simple amidation reaction by using an imidazolium zwitterion and chitosan (CS). The corrosion inhibition property of CS-FGA for mild steel (MS) in a 1.0 M HCl solution was studied by various electrochemical tests and physical characterization methods. The findings indicate that the maximum inhibition efficiency of CS-FGA as a mixed-type inhibitor for MS in 1.0 M HCl solution with 400 mg L-1 reaches 97.6 %, much much higher than the CS and the recently reported chitosan-based inhibitors. Scanning electron microscopy (SEM), atomic force microscopy (AFM), and water contact angle (WCA) results reveal that the CS-FGA molecules firmly adsorb on the MS surface to form a protective layer. The adsorption of CS-FGA on the MS surface belongs to the Langmuir adsorption isotherm containing both the physisorption and chemisorption. According to the X-ray photoelectron spectroscopy (XPS) and UV-vis spectrum, FeN bonds presented on the MS surface further prove the chemisorption between CS-FGA and Fe to generate the stable protective layer. Additionally, theoretical calculations from quantum chemical calculation (DFT) and molecular simulations (MD) were performed to reveal the inhibition mechanism of CS-FGA.

Comparison of MBT biotargets with MBT steel targets for matrix-assisted laser desorption/ionization time of flight mass spectrometry identifications of microorganisms in a clinical microbiology laboratory.

MALDI-TOF MS identifications of microorganisms in a clinical laboratory were investigated, comparing steel targets with MBT Biotargets. By using MBT Biotargets, the score values of yeast identifications increased, whereas the score values of Gram-negative bacteria decreased. Switching to MBT Biotargets did not negatively impact overall frequencies of high confidence identifications.

Pumpkin Leaf Extract Crop Waste as a New Degradable and Environmentally Friendly Corrosion Inhibitor.

The pumpkin leaf was extracted by the decoction method, and it was used as an eco-friendly, nontoxic inhibitor of copper in 0.5 M H2SO4 corrosion media. To evaluate the composition and protective capacity of the pumpkin leaf extract, Fourier infrared spectroscopy, electrochemical testing, XPS, AFM, and SEM were employed. The results showed that the pumpkin leaf extract (PLE) is an effective cathode corrosion inhibitor, exhibiting exceptional protection for copper within a specific temperature range. The corrosion inhibition efficiency of the PLE against copper reached 89.98% when the concentration of the PLE reached 800 mg/L. Furthermore, when the temperature and soaking time increased, the corrosion protection efficiency of 800 mg/L PLE on copper consistently remained above 85%. Analysis of the morphology also indicated that the PLE possesses equally effective protection for copper at different temperatures. Furthermore, XPS analysis reveals that the PLE molecules are indeed adsorbed to form an adsorption film, which is consistent with Langmuir monolayer adsorption. Molecular dynamics simulations and quantum chemical calculations were conducted on the main components of the PLE.

Methacrylic acid in situ modified steel converter slag/natural rubber composites: Resourceful utilization of steelmaking solid wastes.

As a by-product of the steelmaking industry, the large-volume production and accumulation of steel converter slag cause environmental issues such as land occupation and dust pollution. Since metal salts of unsaturated carboxylic acid can be used to reinforce rubber, this study explores the innovative application of in-situ modified steel slag, mainly comprising metal oxides, with methacrylic acid (MAA) as a rubber filler partially replacing carbon black. By etching the surface of steel slag particles with MAA, their surface roughness was increased, and the chemical bonding of metal methacrylate salt was introduced to enhance their interaction with the molecular chain of natural rubber (NR). The results showed that using the steel slag filler effectively shortened the vulcanization molding cycle of NR composites. The MAA in-situ modification effectively improved the interaction between steel slag and NR molecular chains. Meanwhile, the physical and mechanical properties, fatigue properties, and dynamic mechanical properties of the experimental group with MAA in-situ modified steel slag (MAA-in-situ-m-SS) were significantly enhanced compared with those of NR composites partially filled with unmodified slag. With the dosage of 7.5 phr or 10 phr, the above properties matched or even exceeded those of NR composites purely filled with carbon black. More importantly, partially replacing carbon black with modified steel slag reduced fossil fuel consumption and greenhouse gas emission from carbon black production. This study pioneered an effective path for the resourceful utilization of steel slag and the green development of the steelmaking and rubber industries.

Surface adsorption and corrosion resistance performance of modified chitosan: Gravimetric, electrochemical, and computational studies.

Two novel chitosan derivatives (water soluble and acid soluble) modified with thiocarbohydrazide were produced by a quick and easy technique using formaldehyde as links. The novel compounds were synthesized and then characterized by thermogravimetric analysis, elemental analysis, nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy, and differential scanning calorimetry. Their surface morphologies were examined using scanning electron microscopy. These chitosan derivatives could produce pH-dependent gels. The behavior of mild steel in 5 % acetic acid, including both inhibitors at various concentrations, was investigated using gravimetric and electrochemical experiments. According to the early findings, both compounds (TCFACN and TCFWCN) functioned as mixed-type metal corrosion inhibitors. Both inhibitors showed their best corrosion inhibition efficiency at 80 mg L-1. TCFACN and TCFWCN, showed approximately 92 % and 94 % corrosion inhibition, respectively, at an optimal concentration of 80 mg L-1, according to electrochemical analysis. In the corrosion test, the water contact angle of the polished MS sample at 87.90 °C was reduced to 51 °C. The water contact angles for MS inhibited by TCFACN and TCFWCN in the same electrolyte were greater, measuring 78.10 °C and 93.10 °C, respectively. The theoretical results also support the experimental findings.

Eco-friendly anti-corrosion performance of chitosan modified with fused heterocyclic compound on mild steel in acidic medium.

This study aims to explore the prevention of chitosan modified with a fused heterocyclic compound as a sustainable corrosion inhibitor for mild steel in 1 M HCl. Electrochemical instruments, including potentiodynamic polarization techniques, and electrochemical impedance spectroscopy (EIS), were employed to evaluate the corrosion protection performance. The outcomes showed that the chitosan modified with a fused heterocyclic compound has outstanding inhibition performance, with an inhibition effectiveness of 98.25 % at 100 ppm. The anti-corrosion features of modified chitosan were ascribed to the presence of hetero atoms in modified chitosan composite which leads to the creation of a protective layer, The modified chitosan composite behaved as mixed-typed inhibitors, as shown by the PDP results. The modified chitosan composite adsorbs on mild steel in the investigated corrosive media via chemisorption interactions, and its adsorption followed the Langmuir adsorption model. Furthermore, increasing the temperature from 303 to 333 K enhanced the corrosion rate, most likely due to the desorption of the inhibitor agent from the steel surface.

Inhibitory effect of marine Bacillus sp. and its biomineralization on the corrosion of X65 steel in offshore oilfield produced water.

The issue of material failure attributed to microbiologically influenced corrosion (MIC) is escalating in seriousness. Microorganisms not only facilitate corrosion but certain beneficial microorganisms also impede its occurrence. This study explored the impact of marine B. velezensis on the corrosion behavior of X65 steel in simulated offshore oilfield produced water. B. velezensis exhibited rapid growth in the initial stages, and the organic acid metabolites were found to promote corrosion. Subsequently, there was an increase in cross-linked "networked" biofilms products, a significant rise in the prismatic shape of corrosion products, and a tendency for continuous development in the middle and late stages. The organic/inorganic mineralized film layer formed on the surface remained consistently complete. Metabolic products of amino acid corrosion inhibitors were also observed to be adsorbed into the film. B. velezensis altered the kinetics of the X65 steel cathodic reaction, resulting in a deceleration of the electrochemical reaction rate. The mineralization induced by B. velezensis effectively slowed down the corrosion rate of X65 steel.

Influence of marine Shewanella putrefaciens and mediated calcium deposition on Q235 carbon steel corrosion.

The microbiologically influenced corrosion inhibition (MICI) of Q235 carbon steel by Shewanella putrefaciens and mediated calcium deposition were investigated by regulating microbial mineralization. In a calcium-rich medium, S. putrefaciens rapidly created a protective calcium carbonate layer on the steel surface, which blocked Cl- diffusion. Without calcium, the biofilm and rust layer mitigated pitting corrosion but did not prevent Cl- penetration. Potentiodynamic polarization results indicated that the current densities (icorr values) of the corrosion produced in the S. putrefaciens-inoculated media with and without calcium were 0.4 µA/cm2 and 0.6 µA/cm2, respectively. Similarly, compared with those under sterile conditions, the corrosion inhibition rates were 92.2% and 87.4% higher, respectively. Electrochemical impedance spectroscopy (EIS) and scanning electrochemical microscopy (SECM) confirmed that the MICI was caused by the combination of microbial aerobic respiration and the deposited layers. Even under nonbiological conditions, S. putrefaciens-induced calcium carbonate deposition inhibited corrosion.

Origanum Grosii Extracts as Novel Eco-Friendly Corrosion Inhibitors for Mild Steel In HCl Medium.

Two green inhibitors extracted from an endemic species (Origanum grosii (Og)) using two solvents of different polarity (water and ethanol), OgW (aqueous extract) and OgE (ethanolic extract), were used for the anticorrosion of mild steel (M steel) in a 1 M HCl medium. Anticorrosive performance of OgW and OgE was assessed using standard electrochemical techniques, EIS/PDP measurements, weight loss method and SEM/EDX surface analysis. The results show that OgW achieves a maximum inhibition efficiency of 92 % and that the extract in aqueous medium (more polar) is more efficient than the extract in ethanolic medium (less polar). Both extracts act as mixed inhibitors and their corrosion process is predominantly governed by a charge transfer. Concentration and temperature effect was studied and shown that they are two antagonistic parameters for the evolution of inhibitory effectiveness of both OgW and OgE. The adsorption isotherms of the two inhibitors OgE and OgW obey to the Langmuir adsorption model. Moreover, the examination of SEM images and EDX spectra support a deposit of both extracts on the metal surface by an adsorption phenomenon. Besides, theoretical approach of the molecular structures of the major compounds M-OgW and M-OgE and inhibition efficiency was examined via DFT calculations and molecular dynamics simulations and it was consistent with the experimental findings.

Low efficiency of cathodic protection in marine tidal corrosion of X80 steel in the presence of Pseudomonas sp.

Owing to the effects of seawater erosion, dry/wet cycles, dissolved oxygen and microorganisms, the corrosion of steel in marine tidal environments is a serious threat to the safe and stable operation of marine equipment and facilities. Among them, microbiologically influenced corrosion (MIC) of steel has received increasing attention. Cathodic protection (CP) is frequently used to control the corrosion of offshore steel structures. However, in the presence of microorganisms, implementation of CP and its specific effects remain controversial. In this study, the influence of Pseudomonas sp. on the CP efficiency of Zn sacrificial anodes (ZnSAs) during the tidal corrosion of X80 steel was studied. The results showed that CP efficiency exceeded 92% in an abiotic tidal environment. However, in the biotic tidal environment, Pseudomonas sp. significantly reduced the CP efficiency. Pseudomonas sp. and its biofilm promoted the corrosion of steel under CP, inhibited the formation of a complete calcareous deposit layer, which weakened the CP efficiency of ZnSA in the marine tidal environment.

Synthesis, characterization, synergistic inhibition, and biological evaluation of novel Schiff base on 304 stainless steel in acid solution.

A novel Schiff base [4-(morpholin-4-yl) benzylidenyl]thiosemicarbazide (MBT) was created by reaction condensation. The molecules of the products were verified by IR, 1HNMR, MS, and elemental techniques. The synergistic effect of KI with novel MBT on 304 stainless steel (SS) in acidic has been investigated experimentally and theoretically using DFT. The findings demonstrate that restriction efficacy on 304 SS improved with rising inhibitor concentrations, and this benefit was attributed to synergy when KI was injected. From EIS results, IE % increased with a higher concentration of MBT only and MBT + KI (from 100 to 600 ppm). MBT maximum IE % was 84.98%, at 600 ppm. MBT + KI, due to the I- ions synergistic effect, showed an IE% of about 95.48%, at 600 ppm. The adsorptions of MBT and MBT + KI on the surfaces of 304 SS are strongly fitted Langmuir adsorption isotherms. Thermodynamic parameters (Kads, ΔG0ads) were utilized. According to polarization findings, MBT behaves as a mixed-category antagonist. The Schiff base MBT was screened for its in vitro antimicrobial activities against some strains of bacteria and fungi. The result revealed that MBT proved to be an excellent candidate as a fungal agent being able to inhibit Aspergillus flavus.

Lignite-steel slag constructed wetland with multi-functionality and effluent reuse.

Constructed wetlands (CWs) are widely used to treat wastewater, while innovative studies are needed to support resource conservation, enhance multi-functionality, and improve the effectiveness of effluent usage. This study assessed the potential of CW's multiple functions by combining low-rank coal (lignite) and industrial waste (steel slag) in different configurations as CW substrates. The results of scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and metagenomic sequencing showed that the experimental treatment with lignite and steel slag mixtures had the highest multi-functionality, including efficient nutrient removal and carbon sequestration, as well as hydroponic crop production. Lignite and steel slag were mixed to form lignite-steel slag particle clusters, where Ca2+ dissolved on the surface of steel slag was combined with PO43- in wastewater to form Ca3(PO4)2 precipitation for phosphorus removal. A biofilm grew on the surface of lignite in this cluster, and OH- released from steel slag promoted lignite to release fulvic acid, which provided a carbon source for heterotrophic microorganisms and promoted denitrification. Moreover, fulvic acid enhanced carbon sequestration in CWs by increasing the biomass of Phragmites australis. The effluent from lignite-steel slag CW increased cherry tomato yield and quality while saving N and P applications. These results provide new ideas for the "green" and economic development of CW technology.

Performance and mechanisms of alkaline solid waste in CO2 mineralization and utilization.

CO2 mineral sequestration using alkaline solid waste (ASW) is a promising strategy for synergistically reducing CO2 emissions and reusing industrial waste. However, improvement the carbonation degree still remains challenges due to the sluggish leaching rate of Ca/Mg ion at low pH. To the issues, this study proposed an amine-mediated CO2 absorption and mineralization process with six common ASWs, as well an ecological utilization route of CO2-ASW productions. Experimental results indicated that calcium carbide slag (CS) had greater CO2 mineralization capacity (86.2 g-CO2/kg-CS) than other ASWs, while stirring rate and particle size played a more important role during CO2 capture. Amine-mediated CO2 capture was verified to be more excellent with steel slag (SS) as mineral medium. When the MEA concentration was increased to 2 mol/L, the extraction efficiency of Ca2+ was increased by 35 %, leaded to the CO2 removal efficiency significantly promoted from 49 % to 92 %. The characterization of structural morphology referred spherical aragonite or needle-bar calcite was dominant for the porous mineralization products (30.6 m2/g). High germination index of pea seed (112.1 % at a dose of 10 g/L) inferred the negligible toxicological effects of tiny MEA residue over SS mineralization products, after centrifugally washing treatment. Pea seeds cultivated with mineralized products after centrifugal washing can achieve a growth rate of about 4 mm/d. Overall, this work provides a feasible route to apply the porous CO2-ASWs production into water conservation in arid and sandy land.

Hybrid epoxy/Br inhibitor in corrosion protection of steel: experimental and theoretical investigations.

The corrosion of carbon steel infrastructure in acidic environments poses significant economic and safety challenges. Traditional inhibitors such as chromates are being phased out due to toxicity concerns. Thus, there is a need to develop effective and sustainable green alternatives. In this work, we evaluated an epoxy-based inhibitor, bisphenol A tetrabromo dipropoxy dianiline tetraglycidyl ether (TGEDADPTBBA), for protecting carbon steel against corrosion in 1 M hydrochloric acid. An integrated experiment-computation approach was employed. Polarization curves and electrochemical impedance spectroscopy were used to assess the inhibition efficiency and mechanism of TGEDADPTBBA. Quantum chemical calculations and molecular dynamics simulations provided atomic-level insights into adsorption behavior. Scanning electron microscopy with energy-dispersive X-ray spectroscopy characterized the surface morphology. The results showed that TGEDADPTBBA acted as a highly effective mixed-type inhibitor, achieving over 95% inhibition efficiency at a 10-3 M concentration. It suppressed corrosion currents while increasing the charge transfer resistance. Theoretical studies revealed that TGEDADPTBBA adsorbed onto steel surfaces via both electrostatic and van der Waals interactions. This stable adsorption facilitated the formation of a protective barrier layer, as observed experimentally. Notably, our work demonstrated the synergistic potential of combining experimental corrosion testing with computational modeling to develop structure-property relationships for innovative inhibitor design. This integrated approach offers insight into inhibition mechanisms and presents TGEDADPTBBA as an attractive green corrosion inhibitor alternative for industrial applications.

Water-soluble chitosan salt as ecofriendly corrosion inhibitor for N80 pipeline steel in artificial sea water: Experimental and theoretical approach.

Chitosan, as a proficient biopolymer, has enormous potential as an ecofriendly corrosion inhibitor (CI), but their limited solubility restricts practical applications. Herein, an eco-friendly and water-soluble chitosan salt (CS) was utilized as a green CI on N80 pipeline steel in artificial sea water. Several structural and surface analytical tools were engaged in describing the characteristics of novel CS polymer. The corrosion inhibition efficiencies of CS on steel at different concentrations were investigated through gravimetric, conventional and advanced electrochemical techniques along with the surface analyses. Tafel polarization tests specified that CS performed as mixed-type CI with prevalent anodic inhibition characteristics. At a concentration of 1000 ppm, CS provided an inhibition efficiency (IE) of 96.68 %, following physiochemical adsorptions of CS on N80 surface validated by fitting Langmuir adsorption isotherm. However, the reductions in the values of IE at high temperature specified that the CS is the temperature dependent CIs. Scanning electrochemical microscopic evaluation confirmed the formation of thin CS inhibitors films with high electrochemical stability on N80 steel in saline. The performed surface characterizations on inhibited surfaces validated the adsorption of CS on the N80 surface by forming thin inhibitor film to obstruct metal corrosion. The theoretical simulation studies using molecular dynamics and density functional theory corroborated the experimentally obtained results.

Effects of adding steel slag on humification and characteristics of bacterial community during phosphate-amended composting of municipal sludge.

This study aimed to investigate the effects of different proportions (0%, 5%, 7.5%, and 10%) of steel slag (SS) on humification and bacterial community characteristics during phosphate-amended composting of municipal sludge. Compared with adding KH2PO4 alone, co-adding SS significantly promoted the temperature, pH, nitrification, and critical enzyme activities (polyphenol oxidase, cellulase, laccase); especially organic matter (OM) degradation rate (25.5%) and humification degree (1.8) were highest in the 5%-SS treatment. Excitation-emission matrix-parallel factor confirmed that co-adding SS could promote the conversion of protein-like substances or microbial by-products into humic-like substances. Furthermore, adding 5%-SS significantly improved the relative abundances of Actinobacteria, Firmicutes and the genes related to carbohydrate and amino acid metabolism, and enhanced the interactions of bacterial community in stability and complexity. The partial least squares path model indicated that OM was the primary factor affecting humification. These results provided a promising strategy to optimize composting of municipal sludge via SS.