Three-dimensional biogenic C-doped Bi2MoO6/In2O3-ZnO Z-scheme heterojunctions derived from a layered precursor.

Novel 3D biogenic C-doped Bi2MoO6/In2O3-ZnO Z-scheme heterojunctions were synthesized for the first time, using cotton fiber as template. The as-prepared samples showed excellent adsorption and photodegradation performance toward the hazardous antibiotic doxycycline under simulated sunlight irradiation. The morphology, phase composition and in situ carbon doping could be precisely controlled by adjusting processing parameters. The carbon doping in Bi2MoO6/In2O3-ZnO was derived from the cotton template, and the carbon content could be varied in the range 0.9-4.4 wt.% via controlling the heat treatment temperature. The sample with Bi2MoO6/In2O3-ZnO molar ratio of 1:2 and carbon content of 1.1 wt.% exhibited the highest photocatalytic activity toward doxycycline degradation, which was 3.6 and 4.3 times higher than those of pure Bi2MoO6 and ZnInAl-CLDH (calcined layered double hydroxides), respectively. It is believed that the Z-scheme heterojunction with C-doping, the 3D hierarchically micro-meso-macro porous structure, as well as the high adsorption capacity, contributed significantly to the enhanced photocatalytic activity.

Salmonella Typhimurium Sensing Strategy Based on the Loop-Mediated Isothermal Amplification Using Retroreflective Janus Particle as a Nonspectroscopic Signaling Probe.

Loop-mediated isothermal amplification (LAMP) is a powerful gene amplification method, which has many advantages, including high specificity, sensitivity, and simple operation. However, quantitative analysis of the amplified target gene with the LAMP assay is very difficult. To overcome this limitation, we developed a novel biosensing platform for molecular diagnosis by integrating the LAMP method and retroreflective Janus particle (RJP) together. The final amplified products of the LAMP assay are dumbbell-shaped DNA structures, containing a single-stranded loop with two different sequences. Therefore, the concentration of the amplified products can be measured in a manner similar to the sandwich-type immunoassay. To carry out the sandwich-type molecular diagnostics using the LAMP product, two DNA probes, with complementary sequences to the loop-regions, were prepared and immobilized on both the sensing surface and the surface of the RJPs. When the amplified LAMP product was applied to the sensing surface, the surface-immobilized DNA probe hybridized to the loop-region of the LAMP product to form a double-stranded structure. When the DNA probe-conjugated RJPs were injected, the RJPs bound to the unreacted loop-region of the LAMP product. The number of RJPs bound to the loop-region of the LAMP product was proportional to the concentration of the amplified LAMP product, indicating that the concentration of the target gene can be quantitatively analyzed by counting the number of observed RJPs. Using the developed system, a highly sensitive and selective quantification of Salmonella was successfully performed with a detection limit of 102 CFU.

Cadmium-Aluminum Layered Double Hydroxide Microspheres for Photocatalytic CO2 Reduction.

We report the synthesis of cadmium-aluminum layered double hydroxide (CdAl LDH) using the reaction-diffusion framework. As the hydroxide anions diffuse into an agar gel matrix containing the mixture of aluminum and cadmium salts at a given ratio, they react to give the LDH. The LDH self-assembles inside the pores of the gel matrix into a unique spherical-porous shaped microstructure. The internal and external morphologies of the particles are studied by electron microscopy and tomography revealing interconnected channels and a high surface area. This material is shown to exhibit a promising performance in the photoreduction of carbon dioxide using solar light. Moreover, the palladium-decorated version shows a significant improvement in its reduction potential at room temperature.

Percentage depth dose calculation accuracy of model based algorithms in high energy photon small fields through heterogeneous media and comparison with plastic scintillator dosimetry.

Small fields smaller than 4 × 4 cm2 are used in stereotactic and conformal treatments where heterogeneity is normally present. Since dose calculation accuracy in both small fields and heterogeneity often involves more discrepancy, algorithms used by treatment planning systems (TPS) should be evaluated for achieving better treatment results. This report aims at evaluating accuracy of four model-based algorithms, X-ray Voxel Monte Carlo (XVMC) from Monaco, Superposition (SP) from CMS-Xio, AcurosXB (AXB) and analytical anisotropic algorithm (AAA) from Eclipse are tested against the measurement. Measurements are done using Exradin W1 plastic scintillator in Solid Water phantom with heterogeneities like air, lung, bone, and aluminum, irradiated with 6 and 15 MV photons of square field size ranging from 1 to 4 cm2. Each heterogeneity is introduced individually at two different depths from depth-of-dose maximum (Dmax), one setup being nearer and another farther from the Dmax. The central axis percentage depth-dose (CADD) curve for each setup is measured separately and compared with the TPS algorithm calculated for the same setup. The percentage normalized root mean squared deviation (%NRMSD) is calculated, which represents the whole CADD curve's deviation against the measured. It is found that for air and lung heterogeneity, for both 6 and 15 MV, all algorithms show maximum deviation for field size 1 × 1 cm2 and gradually reduce when field size increases, except for AAA. For aluminum and bone, all algorithms' deviations are less for 15 MV irrespective of setup. In all heterogeneity setups, 1 × 1 cm2 field showed maximum deviation, except in 6MV bone setup. All algorithms in the study, irrespective of energy and field size, when any heterogeneity is nearer to Dmax, the dose deviation is higher compared to the same heterogeneity far from the Dmax. Also, all algorithms show maximum deviation in lower-density materials compared to high-density materials.

Monte-Carlo-derived insights into dose-kerma-collision kerma inter-relationships for 50 keV-25 MeV photon beams in water, aluminum and copper.

The relationships between D, K and Kcol are of fundamental importance in radiation dosimetry. These relationships are critically influenced by secondary electron transport, which makes Monte-Carlo (MC) simulation indispensable; we have used MC codes DOSRZnrc and FLURZnrc. Computations of the ratios D/K and D/Kcol in three materials (water, aluminum and copper) for large field sizes with energies from 50 keV to 25 MeV (including 6-15 MV) are presented. Beyond the depth of maximum dose D/K is almost always less than or equal to unity and D/Kcol greater than unity, and these ratios are virtually constant with increasing depth. The difference between K and Kcol increases with energy and with the atomic number of the irradiated materials. D/K in 'sub-equilibrium' small megavoltage photon fields decreases rapidly with decreasing field size. A simple analytical expression for X̅, the distance 'upstream' from a given voxel to the mean origin of the secondary electrons depositing their energy in this voxel, is proposed: X̅(emp) ≈ 0.5R(csda)(E̅(0)), where E̅(0) is the mean initial secondary electron energy. These X̅(emp) agree well with 'exact' MC-derived values for photon energies from 5-25 MeV for water and aluminum. An analytical expression for D/K is also presented and evaluated for 50 keV-25 MeV photons in the three materials, showing close agreement with the MC-derived values.

Timing properties of phosphor-coated polished LSO crystals.

This study investigates a time-of-flight (TOF)-depth-of-interaction (DOI) detector design for positron emission tomography (PET), based on phosphor-coated lutetium oxyorthosilicate (LSO) scintillator crystals coupled to fast single channel photomultiplier tubes. Interaction of the scintillation light with the phosphor coating changes the pulse shape in a depth-dependent manner. 3 × 3 × 10 mm(3) LSO scintillation crystals with polished surfaces were characterized, with and without phosphor coating, to assess DOI capability and timing properties. Two different phosphor coating geometries were studied: coating of the top surface of the crystal, and the top plus half of the crystal sides. There was negligible depth dependency in the decay time when coating only the top surface, however there was a ∼10 ns difference in end-to-end decay time when coating the top plus half of the crystal sides, sufficient to support the use of three DOI bins (3.3 mm DOI bin width). The rise time of the half-coated phosphor crystal was slightly faster at all depths, compared to uncoated crystals, however the signal amplitude was lower. Phosphor coating resulted in depth-dependent photopeak positions with an energy resolution of 13.7%, at a depth of 1 mm, and 15.3%, at a depth of 9 mm, for the half-coated crystal. Uncoated LSO crystals showed no change in photopeak position as a function of depth, with an energy resolution of 10.4%. The head-on coincidence timing resolution (CTR) of two uncoated LSO crystals was 287 ps using constant fraction discrimination for time pick-off. With phosphor coating, the CTR of the top-coated crystal was 314 ps, compared to 384 ps for the half-coated crystal. We demonstrate that the trade-off between timing resolution and DOI resolution can be controlled by the phosphor coating geometry. Here we present preliminary results demonstrating that good DOI resolution can be achieved with only a modest 26% degradation in CTR.

Antifungal efficiency assessment of the TiO2 coating on façade paints.

The work studies the photocatalytic activity and the antifungal efficiency of the TiO2/Zn-Al coatings placed on the target commercial façade paints. The photocatalytic active nanocomposite based on TiO2 and Zn-Al-layered double hydroxides (ZnAl-LDHs) was synthesized by a wet impregnation technique with 3 % w/w TiO2. The freshly prepared suspension was applied by spray technique on the surfaces of the white façade paints. The goal of the work was to develop a method that quickly quantifies the antifungal activity of the commercial façade paints with and without biocidal components covered with a photocatalytic coating. The essence of the proposed method is the monitoring of the fungal growth (artificial ageing conditions) and the quantification of its development (UV-A 0.13 mWcm(-2)) on the façade paint surfaces. A special fungus nutrient (potato dextrose agar (PDA)) was inoculated with the spores of the Aspergillus niger ATCC 6275, and the test samples (façade paints with and without photocatalytic coating) were placed on the inoculated nutrient in the petri dishes. The images of the fungal growth on the samples of the facade paints, during a period of 5 days, were imported into Matlab R2012a where they were converted to binary images (BW), based on the adequate threshold. The percentage of the surface coverage was calculated by applying the specifically written program code which determines the ratio of the black and white pixels. The black pixels correspond to the surface covered with hyphae and mycelia of the fungus.

Effect of multipath laser shock processing on microhardness, surface roughness, and wear resistance of 2024-T3 Al alloy.

Laser shock processing (LSP) is an innovative surface treatment technique with high peak power, short pulse, and cold hardening for strengthening metal materials. LSP is based on the application of a high intensity pulsed laser beam (I > 1 GW/cm(2); t < 50 ns) at the interface between the metallic target and the surrounding medium (a transparent confining material, normally water) forcing a sudden vaporization of the metallic surface into a high temperature and density plasma that immediately develops inducing a shock wave propagating into the material. The shock wave induces plastic deformation and a residual stress distribution in the target material. In this paper we study the increase of microhardness and surface roughness with the increase of laser pulse energy in 2024-T3 Al alloy. The influence of the thickness of the confining layer (water) on microhardness and surface roughness is also studied. In addition, the effect of LSP treatment with best conditions on wear behaviors of the alloy was investigated.

Vibration characteristics of aluminum surface subjected to ultrasonic waves and their effect on wetting behavior of solder droplets.

The vibration characteristics of an aluminum surface subjected to ultrasonic waves were investigated with a combination of numerical simulation and experimental testing. The wetting behavior of solder droplets on the vibrating aluminum surface was also examined. The results show that the vibration pattern of the aluminum surface is inhomogeneous. The amplitude of the aluminum surface exceeds the excitation amplitude in some zones, while the amplitude decreases nearly to zero in other zones. The distribution of the zero-amplitude zones is much less dependent on the strength of the vibration than on the location of the vibration source. The surface of the liquid solder vibrates at an ultrasonic frequency that is higher than the vibration source, and the amplitude of the liquid solder is almost twice that of the aluminum surface. The vibration of the surface of the base metal (liquid solder) correlates with the oxide film removal effect. Significant removal of the oxide film can be achieved within 2s when the amplitude of the aluminum surface is higher than 5.4 µm or when the amplitude of the liquid solder surface is higher than 10.2 µm.

Photocatalytic degradation of 2,4-dichlorophenol with MgAlTi mixed oxides catalysts obtained from layered double hydroxides.

MgAl and MgAlTi mixed oxides were obtained from the thermal treatment of LDH materials synthesized by the sol-gel method; these materials were characterized by N2 physisorption, XRD, UV-vis, XPS, EDS-SEM and TEM techniques. According to the results, Ti was incorporated in the LDH layer when content in the material was low. The MgAl and MgAlTi mixed oxides were evaluated in the photo-degradation of 2,4-dichlorophenol (2,4-DCP) in the presence of UV light. A superior efficiency in the photo-degradation of 2,4-DCP, in comparison with the Degussa P-25 TiO2 reference catalyst was observed, reaching a total decomposition of the 2,4-DCP molecule in less than 60 min. According to the results, Ti was incorporated in the LDH layer when the content in the material was low. The MgAl and MgAlTi mixed oxides were evaluated in the photo-degradation of 2,4-dichlorophenol (2,4-DCP) in the presence of UV light. A superior efficiency in the photo-degradation of 2,4-DCP with the MgAl and MgAlTi mixed oxides, in comparison with the Degussa P-25 TiO2 reference catalyst was observed, reaching a total decomposition of the 2,4-DCP molecule in less than 60 min.

Self-organization of ascending-bubble ensembles.

Self-organization of hydrogen bubbles generated by laser-treated areas of an aluminum plate etched in a basic aqueous solution of ammonia is studied experimentally and theoretically. The dynamics of the establishment of a stationary pattern of gas bubbles is experimentally is shown. In the theoretical model, the velocity field of liquid flows around an ensemble of several bubbles is obtained. Modeling of the process of self-organization of gas bubbles is performed on the basis of a continuum model of a bubble jet. Under certain assumptions, the pressure of a diluted system of bubbles is described by an equation similar to that for nonideal gas, which follows the van der Waals equation of state. The model predicts an alignment of gas bubbles along bisectors of the laser-treated area limited by a square, which is in good agreement with experimental observations. Further development of the model leads to an equation with a negative diffusion coefficient that may be responsible for symmetry breakdown and pattern formation.

An interference coating of metamaterial as an ultrathin light absorber in the violet-to-infrared regime.

A metamaterial with brief and ultrathin structure performs high efficiency in light absorption. An upright aluminum nanorod array (Al NRA) is obliquely deposited, measured, and analyzed its optical property. The Al NRA performs high efficiency of light absorption and low reflectance simultaneously. Based on the measured refractive index and impedances, the wave propagation through the Al NRA is traced to demonstrate the destructive interference that leads to antireflection. According to the analysis of wave tracing, an Al semicontinuous film with thickness of 15nm is introduced under an Al NRA with thickness of only 245nm as a brief and thin two-layered structure. The broadband and polarization-independent light absorption is measured over the violet-to-infrared regime.

Multifunctional Fe3O4 nanoparticles for highly sensitive detection and removal of Al(III) in aqueous solution.

Fe(3)O(4) nanoparticles (NPs) decorated with rhodamine 6G Schiff base, which exhibit high selectivity and sensitivity toward Al(3+) over other common metal ions in aqueous media under a physiological pH window via a 1:1 binding mode, have been synthesized and characterized. The resulting conjugate renders the rhodamine 6G Schiff base unit more water soluble, and the detection limit reaches 0.3 ppb in water. Moreover, can detect Al(3+) in a wide pH span (5.0-11.0) and enrich/remove excess Al(3+) in water via an external magnetic field, which indicates that it has more potential and further practical applications for biology and toxicology. Furthermore, provides good fluorescent imaging of Al(3+) in living cells.

Electron-ion and ion-ion potentials for modeling warm dense matter: Applications to laser-heated or shock-compressed Al and Si.

The pair interactions Uij(r) determine the thermodynamics and linear transport properties of matter via the pair-distribution functions (PDFs), i.e., gij(r). Great simplicity is achieved if Uij(r) could be directly used to predict material properties via classical simulations, avoiding many-body wave functions. Warm dense matter (WDM) is encountered in quasiequilibria where the electron temperature Te differs from the ion temperature Ti, as in laser-heated or in shock-compressed matter. The electron PDFs gee(r) as perturbed by the ions are used to evaluate fully nonlocal exchange-correlation corrections to the free energy, using hydrogen as an example. Electron-ion potentials for ions with a bound core are discussed with Al and Si as examples, for WDM with Te≠Ti, and valid for times shorter than the electron-ion relaxation time. In some cases the potentials develop attractive regions and then become repulsive and "Yukawa-like" for higher Te. These results clarify the origin of initial phonon hardening and rapid release. Pair potentials for shock-heated WDM show that phonon hardening would not occur in most such systems. Defining meaningful quasiequilibrium static transport coefficients consistent with the dynamic values is addressed. There seems to be no meaningful "static conductivity" obtainable by extrapolating experimental or theoretical σ(ω,Ti,Te) to ω→0, unless Ti→Te as well. Illustrative calculations of quasistatic resistivities R(Ti,Te) of laser-heated as well as shock-heated aluminum and silicon are presented using our pseudopotentials, pair potentials, and classical integral equations. The quasistatic resistivities display clear differences in their temperature evolutions, but are not the strict ω→0 limits of the dynamic values.

Excitation functions for 7Be, 22,24Na production in Mg and Al by deuteron irradiations up to 50 MeV.

New experimental data for production of (7)Be and (22,24)Na in deuteron irradiation of (nat)Mg and Al up to 50 MeV are presented. The induced activity, measured with HPGe spectroscopy, allows us to determine excitation functions of (nat)Mg(d,x) and (27)Al(d,x) reactions involved in the activation process with reference to (nat)Ti(d,x)(48)V monitor cross sections. A comparison with experimental literature values and results from updated theoretical codes is discussed. Thick target yields were derived from fits to our cross-sections and integrated personnel dose was calculated for different irradiation cycles and exposure scenarios around high power deuteron accelerator facilities.

Modification of anodised aluminium surfaces using a picosecond fibre laser for printing applications.

The use of an ultrafast fibre laser at a wavelength of 1064 nm has allowed the surface modification of anodised aluminium plates coated with a 2 micron thick anodised layer for potential industrial applications. The micro- and nano-scale structuring of the anodised aluminium using picosecond pulses of approximately 25 ps duration at 200 kHz repetition rate was investigated. The interaction of the laser with the substrate created a hydrophilic surface, giving a contact angle of less than 10 degrees. On examination under a Scanning Electron Microscope (SEM), a morphology created due to laser induced spallation was observed. It has been found that these laser processed hydrophilic surfaces revert to a hydrophobic state with time. This has potential for application in the printing industry and offers reusability and sustainability of the process materials. This has been confirmed in initial trials.

Beam generation and planar imaging at energies below 2.40 MeV with carbon and aluminum linear accelerator targets.

PURPOSE: Recent work has demonstrated improvement of image quality with low-Z linear accelerator targets and energies as low as 3.5 MV. In this paper, the authors lower the incident electron beam energy between 1.90 and 2.35 MeV and assess the improvement of megavoltage planar image quality with the use of carbon and aluminum linear accelerator targets. METHODS: The bending magnet shunt current was adjusted in a Varian linear accelerator to allow selection of mean electron energy between 1.90 and 2.35 MeV. Linac set points were altered to increase beam current to allow experimental imaging in a practical time frame. Electron energy was determined through comparison of measured and Monte Carlo modeled depth dose curves. Planar image CNR and spatial resolution measurements were performed to quantify the improvement of image quality. Magnitudes of improvement are explained with reference to Monte Carlo generated energy spectra. RESULTS: After modifications to the linac, beam current was increased by a factor greater than four and incident electron energy was determined to have an adjustable range from 1.90 MeV to 2.35 MeV. CNR of cortical bone was increased by a factor ranging from 6.2 to 7.4 and 3.7 to 4.3 for thin and thick phantoms, respectively, compared to a 6 MV therapeutic beam for both aluminum and carbon targets. Spatial resolution was degraded slightly, with a relative change of 3% and 10% at 0.20 lp∕mm and 0.40 lp∕mm, respectively, when reducing energy from 2.35 to 1.90 MV. The percentage of diagnostic x-rays for the beams examined here, ranges from 46% to 54%. CONCLUSION: It is possible to produce a large fraction of diagnostic energy x-rays by lowering the beam energy below 2.35 MV. By lowering the beam energy to 1.90 MV or 2.35 MV, CNR improves by factors ranging from 3.7 to 7.4 compared to a 6 MV therapy beam, with only a slight degradation of spatial resolution when lowering the energy from 2.35 MV to 1.90 MV.

Large lateral photovoltaic effects in Co/Alq3 granular films on Si substrates.

A series of Co/Alq3 granular films were deposited on silicon substrates using co-evaporation technique. Under the nonuniform illumination of a laser beam, lateral photovoltaic effect (LPE) was observed in the samples, with the optimal open-circuit position sensitivity of 34.7 mV/mm. The insertion of oxide layer results in the decrease of lateral photovoltage (LPV) and the irreversible LPE. The dependence of lateral photovoltaic effect on substrates was also briefly investigated. The possible mechanism was discussed.

Numerical modeling of large-area beta sources constructed from anodized-aluminum foils.

The numerical modeling of large-area beta sources constructed from anodized-aluminum foils is described in this paper. Based on a realistic model for the activity depth distribution, theoretical lower and upper bounds for the efficiency and the transmission coefficient were calculated and used to analyze the comparison method recommended by ISO 8769 for measuring the surface emission rate. The analysis shows that this method can provide measurement results with relative standard uncertainties smaller than 3% for high energy beta emitters such as (90)Sr-(90)Y, (36)Cl and (204)Tl.

Aluminum nanoparticles for plasmon-improved coupling of light into silicon.

This paper investigates the improved photo-current response obtained by depositing Al nanoparticles on top of a Si diode. Well defined Al nanodiscs with a diameter and height of 100 nm are produced on the surface of a Si diode using electron-beam lithography, and the change in photo-current generation is characterized. A blue shift of the photo-current response is demonstrated, substantially improving the relation between gains and losses compared to what is typically observed in similar schemes using Ag nanoparticles. Enhanced photo-current response is observed in diodes with Al particles on the surface at all wavelengths larger than ≈465 nm, thereby minimizing the losses in the blue range usually reported with Ag nanoparticles on the surface.