Effects of hexagonal boron nitride on mechanical properties of bone cement (Polymethylmethacrylate).

OBJECTIVES: The aim of this study was to investigate the effects of adding hexagonal boron nitride at four different concentrations to polymethylmethacrylate (PMMA) bone cement, which is commonly used in orthopedic surgeries, on the mechanical properties and microarchitecture of the bone cement. MATERIALS AND METHODS: The study included an unaltered control group and groups containing four different concentrations (40 g of bone cement with 0.5 g, 1 g, 1.5 g, 2 g) of hexagonal boron nitride. The samples used for mechanical tests were prepared at 20±2ºC in operating room conditions, using molds in accordance with the test standards. As a result of the tests, the pressure values at which the samples deformed were determined from the load-deformation graphs, and the megapascal (MPa) values at which the samples exhibited strength were calculated. RESULTS: The samples with 0.5 g boron added to the bone cement had significantly increased mechanical strength, particularly in the compression test. In the group where 2 g boron was added, it was noted that, compared to the other groups, the strength pressure decreased and the porosity increased. The porosity did not change particularly in the group where 0.5 g boron was added. CONCLUSION: Our study results demonstrate that adding hexagonal boron nitride (HBN) to bone cement at a low concentration (0.5 g / 40 g PPMA) significantly increases the mechanical strength in terms of MPa (compression forces) without adversely affecting porosity. However, the incorporation of HBN at higher concentrations increases porosity, thereby compromising the biomechanical properties of the bone cement, as evidenced by the negative impact on compression and four-point bending tests. Boron-based products have gained increased utilization in the medical field, and HBN is emerging as a promising chemical compound, steadily growing in significance.

Chondromyxoid fibroma: A retrospective evaluation of 31 cases.

OBJECTIVES: This study aimed to review a 35-year experience with chondromyxoid fibroma at our institution. PATIENTS AND METHODS: The study retrospectively analyzed the records of 31 consecutive patients (17 males, 14 females; mean age: 30.5±15.7 years; range, 6 to 63 years) with chondromyxoid fibroma who were treated between January 1988 and December 2021. The clinical and radiological characteristics of lesions, tumor volume, and recurrence rates were assessed using the tumor archive of the hospital. RESULTS: The mean follow-up duration was 65.9±42.0 months. Pelvis, proximal tibia, and distal femur were the most common sites of localization. The initial surgical treatment was performed on 27 patients at our clinic, while four patients were referred to the clinic after recurrence. The overall recurrence rate was 16.1%. Intralesional curettage was applied to 21 (77.8%) out of 27 patients. The cavity created after curettage was filled with bone graft (autograft or allograft) in 15 (55.5%) cases. Bone cement was applied in four (14.8%) cases. Resection was applied to five (18.5%) patients. In two (7.4%) cases, intralesional curettage alone was performed. One of these two patients experienced recurrence, resulting in a recurrence rate of 50% in this patient group. No recurrence was observed in other treatment groups. CONCLUSION: Intralesional curettage and filling the defect with bone graft or cement were effective for local control in most cases. Curettage alone was associated with high recurrence rates.

Cement-augmented locked plate fixation proximal humerus fractures in elderly patient: a systematic review and meta-analysis.

BACKGROUND: This systemic review and meta-analysis aimed to evaluate the clinical outcomes of proximal humeral fracture in elderly patient fixation using locked plate with or without cement augmentation. METHODS: The databases of PubMed, Embase, and Cochrane Library were searched in August 2023 for literature comparing the clinical outcomes of patients with PHFs treated with locked plate alone and locked plate augmented with cement. Data describing study design; level of evidence; inclusion criteria; demographic information; final follow-up; revision rate; implant failure rate; avascular necrosis rate; total complication rate; constant score; and disability of arm, shoulder, and hand (DASH) score were collected. RESULTS: Eight studies (one randomized-controlled trial and seven observational studies), involving 664 patients, were identified. Compared with locked plates alone, using cement-augmented locked plates reduced the implant failure rate (odds ratio (OR) = 0.19; 95% confidence interval (CI) 0.10-0.39; P < 0.0001) and total complication rate (OR = 0.45; 95% CI 0.29-0.69; P = 0.0002) and improved DASH scores (mean difference (MD) = 2.99; 95% CI 1.00-4.98; P = 0.003). However, there was no significant difference in clinical outcomes, including revision rate, avascular necrosis rate, and constant score. CONCLUSION: In this review and meta-analysis, fixation of the PHFs in elderly patients using locked plates with or without cement augmentation has no significant difference in revision rate, but the implant failure and total complication rates may be lesser on using the cement-augmented locked plate for fixation than on using a locked plate alone. Good results are expected for most patients treated with this technique. TRIAL REGISTRATION: The Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA)21 guidelines were followed to conduct this systematic review and meta-analysis and was registered as a protocol in PROSPERO (CRD42022318798).

Antibiotic-loaded bone cement fixation technique combined with bilateral pectoralis major muscle flaps tension-free management for sternal infection after midline sternotomy.

INTRODUCTION: Deep sternal wound infection (DSWI) after midline sternotomy of cardiac surgery is a challenging complication that affects the outcome of surgery. This study aims to assess the clinical effectiveness of the antibiotic-loaded bone cement fixation technique combined with bilateral pectoralis major muscle flaps tension-free management in the treatment of DSWI. METHODS: We retrospectively analyzed 5 patients with DSWI who underwent antibiotic-loaded bone cement combined with bilateral pectoralis major muscle flaps for chest wall reconstruction after sternotomy for cardiac surgery in a tertiary hospital in China from January 2020 to December 2021. The clinical and follow-up data were retrospectively analyzed. RESULTS: All patients had no perioperative mortalities, no postoperative complications, 100% wound healing, and an average hospital stay length of 24 days. The follow-up periods were from 6 to 35 months (mean 19.6 months). None of the cases showed wound problems after initial reconstruction using antibiotic-loaded bone cement combined with bilateral pectoralis major muscle flaps. CONCLUSIONS: We report our successful treatment of DSWI, using antibiotic-loaded bone cement fixation technique combined with bilateral pectoralis major muscle flaps tension-free management. The clinical and follow-up results are favorable.

Research progress on the application of magnesium phosphate bone cement in bone defect repair: A review.

BACKGROUND: Bone defects arising from diverse causes, such as traffic accidents, contemporary weapon usage, and bone-related disorders, present significant challenges in clinical treatment. Prolonged treatment cycles for bone defects can result in complications, impacting patients' overall quality of life. Efficient and timely repair of bone defects is thus a critical concern in clinical practice. OBJECTIVE: This study aims to assess the scientific progress and achievements of magnesium phosphate bone cement (MPC) as an artificial bone substitute material. Additionally, the research seeks to explore the future development path and clinical potential of MPC bone cement in addressing challenges associated with bone defects. METHODS: The study comprehensively reviews MPC's performance, encompassing e.g. mechanical properties, biocompatibility, porosity, adhesion and injectability. Various modifiers are also considered to broaden MPC's applications in bone tissue engineering, emphasizing drug-loading performance and antibacterial capabilities, which meet clinical diversification requirements. RESULTS: In comparison to alternatives such as autogenous bone transplantation, allograft, polymethyl methacrylate (PMMA), and calcium phosphate cement (CPC), MPC emerges as a promising solution for bone defects. It addresses limitations associated with these alternatives, such as immunological rejection and long-term harm to patients. MPC can control heat release during the curing process, exhibits superior mechanical strength, and has the capacity to stimulate new bone growth. CONCLUSION: MPC stands out as an artificial bone substitute with appropriate mechanical strength, rapid degradation, non-toxicity, and good biocompatibility, facilitating bone repair and regeneration. Modification agents can enhance its clinical versatility. Future research should delve into its mechanical properties and formulations, expanding clinical applications to create higher-performing and more medically valuable alternatives in bone defect repair.

Combining antibiotic-loaded bone cement-based free vastus lateralis muscle-sparing flap with split-thickness skin grafts: A reliable strategy for reconstructing diabetic foot ulcers at non-weight-bearing areas.

Diabetic foot ulcers (DFUs) present significant challenges due to their associated amputation rates, mortality, treatment complexity and excessive costs. Our earlier work introduced a wound surgical integrated treatment (WSIT) for DFUs, yielding promising outcomes. This study focuses on a specific WSIT protocol employing antibiotic-loaded bone cement (ALBC) in the first Stage, and free vastus lateralis muscle-sparing (VLMS) flaps and split-thickness skin grafts (STSGs) in the second stage to repair non-weight-bearing DFUs. From July 2021 to July 2023, seven DFU patients (aged 47-71 years) underwent this treatment. Demographic data, hospital stay and repair surgery times were collected. Histological and immunohistochemical analyses assessed angiogenesis, collagen deposition and inflammation. SF-36 questionnaire measured pre- and postoperative quality of life. Preoperative ultrasound Doppler showed that the peak blood flow velocity of the recipient area artery was significantly >30 cm/s (38.6 ± 6.8 cm/s) in all patients. Muscle flap sizes varied from 8 × 3.5 × 1 to 18 × 6 × 2 cm. The operation time of the repair surgery was 156.9 ± 15.08 minutes, and the hospital stay was 18.9 ± 3.3 days. Histological analysis proved that covering DFUs with ALBC induced membrane formation and increased collagen, neovascularization and M2 macrophages fraction while reducing M1 macrophages one. All grafts survived without amputation during a 7- to 24-month follow-up, during which SF-36 scores significantly improved. A combination of ALBC with free VLMS flaps and STSGs proved to be safe and effective for reconstructing non-weight-bearing DFUs. It rapidly controlled infection, enhanced life quality and foot function, and reduced hospitalization time. We advocate integrating this strategy into DFU treatment plans.

Finite element study on the micromechanics of cement-augmented proximal femoral nail anti-rotation (PFNA) for intertrochanteric fracture treatment.

Blade cut-out is a common complication when using proximal femoral nail anti-rotation (PFNA) for the treatment of intertrochanteric fractures. Although cement augmentation has been introduced to overcome the cut-out effect, the micromechanics of this approach remain to be clarified. While previous studies have developed finite element (FE) models based on lab-prepared or cadaveric samples to study the cement-trabeculae interface, their demanding nature and inherent disadvantages limit their application. The aim of this study was to develop a novel 'one-step forming' method for creating a cement-trabeculae interface FE model to investigate its micromechanics in relation to PFNA with cement augmentation. A human femoral head was scanned using micro-computed tomography, and four volume of interest (VOI) trabeculae were segmented. The VOI trabeculae were enclosed within a box to represent the encapsulated region of bone cement using ANSYS software. Tetrahedral meshing was performed with Hypermesh software based on Boolean operation. Finally, four cement-trabeculae interface FE models comprising four interdigitated depths and five FE models comprising different volume fraction were established after element removal. The effects of friction contact, frictionless contact, and bond contact properties between the bone and cement were identified. The maximum micromotion and stress in the interdigitated and loading bones were quantified and compared between the pre- and post-augmentation situations. The differences in micromotion and stress with the three contact methods were minimal. Micromotion and stress decreased as the interdigitation depth increased. Stress in the proximal interdigitated bone showed a correlation with the bone volume fraction (R2 = 0.70); both micromotion (R2 = 0.61) and stress (R2 = 0.93) at the most proximal loading region exhibited a similar correlation tendency. When comparing the post- and pre-augmentation situations, micromotion reduction in the interdigitated bone was more effective than stress reduction, particularly near the cement border. The cementation resulted in a significant reduction in micromotion within the loading bone, while the decrease in stress was minimal. Noticeable gradients of displacement and stress reduction can be observed in models with lower bone volume fraction (BV/TV). In summary, cement augmentation is more effective at reducing micromotion rather than stress. Furthermore, the reinforcing impact of bone cement is particularly prominent in cases with a low BV/TV. The utilization of bone cement may contribute to the stabilization of trabecular bone and PFNA primarily by constraining micromotion and partially shielding stress.

Advantages of unilateral percutaneous kyphoplasty for osteoporotic vertebral compression fractures-a systematic review and meta-analysis.

Data from English randomized controlled trials comparing unilateral versus bilateral PKP for the treatment of OVCFs were retrieved and analyzed, and the results showed that unilateral PKP is a better choice for the treatment of patients with OVCFs, which will provide a reliable clinical rationale for the treatment of OVCFs. PURPOSE: To investigate the advantages of unilateral percutaneous kyphoplasty (PKP) for the treatment of osteoporotic vertebral compression fractures(OVCFs). METHODS: The systematic evaluation program met all program requirements (CRD 42023422383) by successfully passing the PROSPERO International Prospective Systematic Evaluation Registry. Researchers searched the references of English-language randomized controlled trials comparing unilateral and bilateral PKP for the treatment of osteoporotic vertebral compression fractures published between 2010 and 2023 and manually searched for known primary and review articles. The study statistically analyzed data from all the included literature, which primarily included time to surgery, visual pain score(VAS) and Oswestry disability index(ODI) at postoperative follow-up time points, polymethylmethacrylate (PMMA, bone cement) injection dose, cement leakage, radiation dose, and improvement in kyphotic angle. RESULTS: This meta-analysis searched 416 articles published from 2010 to 2023 based on keywords, and 18 articles were finally included in this study. The results of the forest plot showed that unilateral PKP operative time, amount of bone cement used, and radiation dose to the patient were significantly reduced (p < 0.01, p < 0.01, and p < 0.01, respectively), and unilateral and bilateral PKP had comparable cement leakage (p = 0.49, 95% CI = 0.58-1.30), and there was no significant difference in the kyphotic angle between unilateral and bilateral PKP (p = 0.42, 95% CI = - 2.29-0.96). During follow-up, there was no significant difference in pain relief between unilateral and bilateral PKP (p = 0.70, 95% CI = - 0.09-0.06), nor was there a significant difference in ODI (p = 0.27, 95% CI = - 0.35-1.24). CONCLUSIONS: There is no difference in clinical efficacy between unilateral PKP and bilateral PKP, but unilateral PKP has a shorter operative time, a lower incidence of cement leakage, a lower amount of cement, and a lower radiation dose to the patient and operator. Unilateral PKP is a better option for patients with OVCFs.

Impact of osteoporosis and Cement-Augmented fusion on adjacent spinal levels Post-Fusion Surgery: Patient-Specific finite element analysis.

Cement-augmentation is a technique commonly used during posterior lumbar instrumented fusion (PLIF) to reinforce compromised osteoporotic vertebral bone, minimize the risk of loosening screws, enhance stability, and improve overall surgical outcomes. In this study, we introduce a novel segmented vertebral body regional modeling approach to investigate the effects of osteoporosis and cement-augmented lumbar fusion on disc biomechanics at spinal levels adjacent to the fused vertebrae. Using our previously validated personalized-poroelastic-osteoligamentous FE model of the spine, fusion was simulated at L4-L5, and the biomechanics of adjacent levels were studied for 30 patients (non-osteoporotic patients (N = 15), osteoporotic patients (N = 15)). PLIF models, with and without cement-augmentation, were developed and compared after an 8 h-rest period (200 N), following a 16 h-cyclic compressive loading of 500-1000 N (40 and 20 min, respectively). Movement in different directions (flexion/ extension/ lateral bending/ axial rotation) was simulated using 10Nm moment before and after cyclic loading. The material mapping algorithm was validated by comparing the results of voxel-based and parametric models. The FE cement-augmented models, subject to daily activity loading, demonstrated significant differences in disc height loss and fluid loss as compared to non-cemented models. The calculated axial stress and fiber strain values were also significantly higher for these models. This work demonstrates that although osteoporosis does not significantly alter the time-dependent characteristics of adjacent IVDs post-surgery, cement-augmentation increases the risk of adjacent segment disease (ASD) incidence. A holistic understanding of the trade-offs and long-term complex interplay between structural reinforcement modalities, including cement augmentation, and altered biomechanics warrants further investigation.

Design and In Vitro Validation of an Orthopaedic Drill Guide for Femoral Stem Revision in Total Hip Arthroplasty.

OBJECTIVE: Cemented total hip arthroplasty (THA) demonstrates superior survival rates compared to uncemented procedures. Nevertheless, most younger patients opt for uncemented THA, as removing well-fixed bone cement in the femur during revisions is complex, particularly the distal cement plug. This removal procedure often increases the risk of femoral fracture or perforation, haemorrhage and weakening bone due to poor drill control and positioning. Aim of this study was to design a novel drill guide to improve drill positioning. METHODS AND PROCEDURES: A novel orthopaedic drill guide was developed, featuring a compliant centralizer activated by a drill guide actuator. Bone models were prepared to assess centralizing performance. Three conditions were tested: drilling without guidance, guided drilling with centralizer activation held, and guided drilling with centralizer activation released. Deviations from the bone centre were measured at the entry and exit point of the drill. RESULTS: In the centralizing performance test, the drill guide significantly reduced drill hole deviations in both entry and exit points compared to the control ([Formula: see text]). The absolute deviation on the exit side of the cement plug was 10.59mm (SD 1.56) for the 'No drill guide' condition, 3.02mm (SD 2.09) for 'Drill guide - hold' and 2.12mm (SD 1.71) for 'Drill guide - release'. The compliant drill guide centralizer significantly lowered the risk of cortical bone perforation during intramedullary canal drilling in the bone models due to better control of the cement drill position. Clinical and Translational Impact Statement: The drill guide potentially reduces perioperative risks in cemented femoral stem revision. Future research should identify optimal scenarios for its application.

Finite element analysis of biomechanical effects of percutaneous cement discoplasty in scoliosis.

OBJECTIVE: To investigate the effect of bone cement on the vertebral body and biomechanical properties in percutaneous cement discoplasty (PCD) for degenerative lumbar disc disease. METHODS: Three-dimensional reconstruction of L2 ~ L3 vertebral bodies was performed in a healthy volunteer, and the corresponding finite element model of the spine was established. Biomechanical analysis was performed on the changes in stress distribution in different groups of models by applying quantitative loads. RESULTS: Models with percutaneous discoplasty (PCD) showed improved stability under various stress conditions, and intervertebral foraminal heights were superior to models without discoplasty. CONCLUSION: Cement discoplasty can improve the stability of the vertebral body to a certain extent and restore a certain height of the intervertebral foramen, which has a good development prospect and potential.

Comparison of the clinical outcomes between proximal femoral nail anti-rotation with cement enhancement and hemiarthroplasty among elderly osteoporotic patients with intertrochanteric fracture.

BACKGROUND: The proximal femoral nail anti-rotation (PFNA) with cement enhancement enhances the anchorage ability of internal fixation in elderly with osteoporotic intertrochanteric fracture. However, whether it is superior to hemiarthroplasty is still controversial. The present study aimed to determine which treatment has better clinical outcomes among older patients. METHODS: We retrospectively analyzed 102 elderly patients with osteoporosis who developed intertrochanteric fractures and underwent PFNA combined with cement-enhanced internal fixation (n = 52, CE group), and hemiarthroplasty (n = 50, HA group) from September 2012 to October 2018. All the intertrochanteric fractures were classified according to the AO/OTA classification. Additionally, the operative time, intraoperative blood loss, intraoperative and postoperative blood transfusion rates, postoperative weight-bearing time, hospitalization time, Barthel Index of Activities Daily Living, Harris score of hip function, visual analog (VAS) pain score, and postoperative complications were compared between the two groups. RESULTS: The CE group had significantly shorter operative time, lesser intraoperative blood loss, lower blood transfusion rate, and longer postoperative weight-bearing time than the HA group. The CE group had lower Barthel's Index of Activities of Daily Living, lower Harris' score, and higher VAS scores in the first and third months after surgery than the HA group, but no difference was observed between the two groups from 6 months to 12 months. There was no significant difference in the total post-operative complications between the two groups. CONCLUSION: The use of PFNA combined with a cement-enhanced internal fixation technique led to shorter operative time and lesser intraoperative blood loss and trauma in elderly patients as compared to HA.

Percutaneous kyphoplasty with or without posterior pedicle screw fixation for the management of severe osteoporotic vertebral compression fractures with nonunion.

OBJECTIVE: To assess the radiographic outcomes, clinical outcomes and complications of percutaneous kyphoplasty (PKP) with and without posterior pedicle screw fixation (PPSF) in the treatment of severe osteoporotic vertebral compression fractures (sOVCF) with nonunion. METHODS: This study involved 51 patients with sOVCF with nonunion who underwent PKP or PPSF + KP. The operation time, intraoperative blood loss, volume of injected bone cement, operation costs and hospital stays were all recorded. In addition, the Visual Analogue Scale (VAS) and the Oswestry Disability Index (ODI) were assessed separately for each patient before and after surgery. RESULTS: Compared with the PPSF + KP group, the PKP group had shorter operation time, less intraoperative blood loss, shorter hospital stays and fewer operation costs. However, cobb's angle improvement (13.4 ± 4.3° vs. 21.4 ± 5.3°), VWR improvement ratio (30.4 ± 11.5% vs. 52.8 ± 12.7%), HA (34.9 ± 9.0% vs. 63.7 ± 7.6%) and HM (28.4 ± 11.2% vs. 49.6 ± 7.7%) improvement ratio were all higher in PPSF + KP group than that in PKP group. In addition, the ODI index and VAS score in both groups were significantly decreased at the postoperative and final follow-up. PKP group's postoperative VAS score was significantly lower than that in PPSF + KP group, but there was no statistically significant difference in VAS score at the last follow-up. CONCLUSION: PKP and PPSF + KP can both effectively relieve the pain associated with sOVCF with nonunion. PPSF + KP can achieve more satisfactory vertebral reduction effects compared to PKP. However, PKP was less invasive and it has more advantages in shortening operation time and hospital stay, as well as decreasing intraoperative blood loss and operation costs.

Influence of rice husk ash on the mechanical properties of ultra-high strength engineered cementitious composites (UHS-ECC).

Generally, UHS-ECC should consume massive cement, which is negative to its sustainability as cement production leads to 8% of global CO2 emissions. To decrease the cost of production and carbon emissions of UHS-ECC, rice husk ash was employed to replace the cement as a supplementary cementitious material in this study. Experiment results illustrate that blending rice husk ash (RHA) would decrease the fluidity of mortar. Furthermore, the green UHS-ECC shows a maximum compressive strength of 130.3 MPa at 28 days when RHA content was 20% of cement. The ultimate tensile strength of UHS-ECCs first increased and then decreased, while both tensile strain and strain energy presented an opposite tendency. At the micro-scale, if RHA content was lower than 20% of cement, incorporating RHA can significantly decreasing fiber bridging complementary energy of UHS-ECC, thus reducing pseudo strain hardening energy (PSHenergy) index, which finely agrees with the degradation of ductility of UHS-ECCs. To guarantee the features of ultra-high strength, acceptable workability, and high tensile ductility, the RHA dosage should not be in excess 20% of cement. These researched results are prospected to the contribution of pozzolanic RHA on the efficient usage of sustainable UHS-ECC.

[Vertebral fractures combined with prolonged activated partial prothrombin time: A case report].

With the development of modern medical standards, autoimmune diseases and their associated successive osteoporosis have received increasing attention in recent years. Patients with autoimmune diseases, due to the characteristics of the disease and the prolonged use of glucocorticoid hormone therapy, may affect the bone formation and bone absorption of the patient, followed by severe successive osteoporosis, thereby increasing the risk of osteoporotic vertebral fractures. Vertebral compression fractures of the spine are common fracture types in patients with osteoporotic fractures. Osteoporosis is a common complication after glucocorticoid therapy in patients with autoimmune diseases. Percutaneous vertebroplasty (PVP) and percutaneous kyphoplasty (PKP) are minimally invasive operation and are commonly used surgical methods for the treatment of osteoporotic vertebral compression fractures. However, due to the operation of spinal puncture during the operation, there are serious surgical risks such as bone cement leakage, spinal epidural hemorrhage, subdural hemorrhage, and subarachnoid hemorrhage in both PVP and PKP. As a result, it is necessary to evaluate the patient' s body before surgery carefully, especially in the case of blood coagulation. This article reports a case of autoimmune disease patient admitted to Peking University People' s Hospital due to lumbar 4 vertebral compression fracture combined with Sjögren' s syndrome. The patient' s preoperative examination showed that the activated partial thromboplastin time (APTT) was significantly prolonged. After completing the APTT extended screening experiment and lupus anticoagulant factor testing, the multi-disciplinary team (MDT) of Peking University People' s Hospital jointly discussed the conclusion that the patient' s test results were caused by an abnormal self-immunity anti-copulant lupus (LAC). Based on the results of the laboratory examination, the patient was considered to be diagnosed with combined antiphospholipid syndrome (APS). For such patients, compared with the patient' s tendency to bleed, we should pay more attention to the risk of high blood clotting in the lower limbs of the patient, pulmonary clots and so on. With timely anti-coagulation treatment, the patient safely passed the peripheral period and was successfully discharged from the hospital. Therefore, for patients with autoimmune diseases with prolonged APTT in the perioperative period, doctors need to carefully identify the actual cause and carry out targeted treatment in order to minimize the risk of surgical and perioperative complications and bring satisfactory treatment results to the patients.

Influence of pozzolanic addition on strength and microstructure of metakaolin-based concrete.

The intent of this study is to explore the physical properties and long-term performance of concrete made with metakaolin (MK) as a binder, using microsilica (MS) and nanosilica (NS) as substitutes for a portion of the ordinary Portland cement (OPC) content. The dosage of MS was varied from 5% to 15% for OPC-MK-MS blends, and the dosage of NS was varied from 0.5% to 1.5% for OPC-MK-NS blends. Incorporation of these pozzolans accelerated the hardening process and reduced the flowability, consistency, and setting time of the cement paste. In addition, it produced a denser matrix, improving the strength of the concrete matrix, as confirmed by scanning electron microscopy and X-ray diffraction analysis. The use of MS enhanced the strength by 10.37%, and the utilization of NS increased the strength by 11.48% at 28 days. It also reduced the penetrability of the matrix with a maximum reduction in the water absorption (35.82%) and improved the resistance to the sulfate attack for specimens containing 1% NS in the presence of 10% MK. Based on these results, NS in the presence of MK can be used to obtain cementitious structures with the enhanced strength and durability.