Bio-Based Polyurethane Networks Containing Sunflower Oil Based Polyols.

This work focused on the preparation and investigation of polyurethane (SO-PU)-containing sunflower oil glycerides. By transesterification of sunflower oil with glycerol, we synthesized a glyceride mixture with an equilibrium composition, which was used as a new diol component in polyurethanes in addition to poly(ε-caprolactone)diol (PCLD2000). The structure of the glyceride mixture was characterized by physicochemical methods, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS), nuclear magnetic resonance spectroscopy (NMR), and size exclusion chromatography (SEC) measurements. The synthesis of polyurethanes was performed in two steps: first the prepolymer with the isocyanate end was synthesized, followed by crosslinking with an additional amount of diisocyanate. For the synthesis of the prepolymer, 4,4'-methylene diphenyl diisocyanate (MDI) or 1,6-hexamethylene diisocyanate (HDI) were used as isocyanate components, while the crosslinking was carried out using an additional amount of MDI or HDI. The obtained SO-PU flexible polymer films were characterized by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). The so-obtained flexible SO-PU films were proved to be suitable for the preparation of potentially biocompatible and/or biodegradable scaffolds. In addition, the stress versus strain curves for the SO-PU polymers were interpreted in terms of a mechanical model, taking into account the yield and the strain hardening.

Evaluation of Monomer-containing Isocyanate Groups on Stabilizing Demineralized Dentin Matrix Against Bond Interface Degradation.

PURPOSE: To evaluate the effect of urethane methacrylate precursor (UMP) on the enzymatic resistance of demineralized dentin (DD) matrices. MATERIALS AND METHODS: Experimental treatments containing 0 (control), 1, and 5 mmol/L UMP dissolved in an acetone (Ace) solution were formulated. Dentin matrix specimens were demineralized in vitro and immersed in the experimental treatments for 1 h. The treated specimens were then stored in 0.1 mg/mL collagenase solution for 24 h, after which their dry mass loss and hydroxyproline (HYP) release were assessed. The swelling ratios of specimens in each group were also evaluated. The interaction between UMP and the dentin matrix was observed using field-emission scanning electron microscopy (FE-SEM). Endogenous enzyme activity in dentin was evaluated using confocal laser scanning microscopy (CLSM). RESULTS: Compared with the other treatment groups, treatment with 1 mM and 5 mM UMP-Ace significantly decreased the dry mass loss, HYP release and swelling ratio of the DD matrix (p < 0.05). FE-SEM and CLSM observations showed that treatment with UMP-Ace protected the structure of the dentin matrix and decreased porosity within the dentin-collagen network. CONCLUSION: Treatment with 1 mM and 5 mM UMP-Ace protects DD matrix against collagenase degradation and may be clinically useful for improving the durability of the hybrid layer.

Exploring structure/property relationships to health and environmental hazards of polymeric polyisocyanate prepolymer substances-3. Aquatic exposure and hazard of aliphatic diisocyanate-based prepolymers.

The water extractability and acute aquatic toxicity of seven aliphatic diisocyanate-based prepolymer substances were investigated to determine if lesser reactivity of the aliphatic isocyanate groups, as well as increased ionization potential of the expected (aliphatic amine-terminated) polymeric hydrolysis products, would influence their aquatic behavior compared to that of previously investigated aromatic diisocyanate-based prepolymers. At loading rates of 100 and 1,000 mg/L, only the substances having log Kow ≤9 exhibited more than 1% extractability in water, and a maximum of 66% water extractability was determined for a prepolymer having log Kow = 2.2. For the more hydrophobic prepolymer substances (log Kow values from 18-37), water extractability was negligible. High-resolution mass spectrometric analyses were performed on the water-accommodated fractions (WAF) of the prepolymers, which indicated the occurrence of primary aliphatic amine-terminated polymer species having backbones and functional group equivalent weights aligned to those of the parent prepolymers. Measurements of reduced surface tension and presence of suspended micelles in the WAFs further supported the occurrence of these surface-active cationic polymer species as hydrolysis products of the prepolymers. Despite these characteristics, the water-extractable hydrolysis products were practically non-toxic to Daphnia magna. All of the substances tested exhibited 48-h EL50 values of >1,000 mg/L, with one exception of EL50 = 157 mg/L. The results from this investigation support a grouping of the aliphatic diisocyanate-based prepolymers as a class of water-reactive polymer substances having predictable aquatic exposure and a uniformly low hazard potential, consistent with that previously demonstrated for the aromatic diisocyanate-based prepolymers.

"Isocyanates and isocyanides - life-threatening toxins or essential compounds?"

Isocyanides and isocyanates are some of the most reactive compounds in organic chemistry, making them perceived as compounds with high potential for use in both the laboratory and industry. With their high reactivity also comes several disadvantages, most notably their potentially high toxicity. The following article is a collection of information on the toxic effects of the isocyanide group on the human body and the environment. Information on the mechanism of how these harmful substances affect living tissues and the environment, worldwide information on how to protect against these chemicals, current regulations, and exposure limits for specific countries is compiled. The latest research on the application uses of isocyanates and isocyanides is also outlined, as well as the latest safer and greener methods and techniques to work with these compounds. Additionally, the presented article can serve as a brief guide to the organic toxicity of a group of isocyanates and isocyanates.

Gastric perforation after polyurethane foam ingestion.

INTRODUCTION: Acute intoxication rarely produces conditions that require urgent surgical care. CASE SUMMARY: A 45-year-old man presented to the emergency department with severe abdominal pain after the deliberate ingestion of 200 cm3 of polyurethane mixed with methylene diphenyl diisocyanate and urethane primers. On an initial laparoscopic examination, foreign material was observed in the peritoneal space with haemoperitoneum. Emergency exploration was then undertaken for suspected gastric perforation. Full-thickness damage was identified on the stomach wall during the operation. The material in the gastrointestinal tract and peritoneal space was gently removed. Moulded casts of the entire stomach and distal oesophagus were extracted successfully. The patient was discharged 14 days after surgery. IMAGES: Computed tomography revealed foreign material occupying the entire gastric chamber, as well as diffuse gastric perforation. CONCLUSIONS: Life-threatening gastric perforation can occur after polyurethane foam ingestion. Clinical/medical toxicologists and emergency physicians need to be aware of the highly expandable nature of this agent.

COVID-19 mortality in 1984 Bhopal gas tragedy survivors: implications for chemically exposed populations.

Leakage of methyl isocyanate from the Union Carbide plant in Bhopal, India, killed thousands and left deleterious trans-generational effects. Gas-exposed populations experience higher rates of lung and metabolic diseases, and immune dysregulation, all associated with adverse outcomes in coronavirus disease 2019 (COVID-19). We used publicly available, official data from government sources to estimate COVID-19-associated crude mortality in populations with and without a history of gas exposure. Overall, there were 1240 deaths among patients hospitalized with known COVID-19 in Bhopal, of which 453 (36.53%) were in gas-exposed individuals, 726 (58.55%) were in gas-unexposed individuals and the exposure status of 61 (4.92%) individuals could not be determined. There were 351 and 375 deaths in gas-unexposed people in the first (April 2020-February 2021) and second (March 2021-July 2021) waves, respectively; in the gas-exposed population, there were 300 and 153 deaths in the two respective waves. The overall annualized crude mortality of COVID-19 was 3.84 (95% CI 3.41 to 4.33) times higher in the gas-exposed population at 83.6 (95% CI 76.1 to 91.7) per 100 000 compared with the gas-unexposed population, at 21.8 (95% CI 20.2 to 23.4) per 100,000. When stratified by age, compared with unexposed people, the gas-exposed individuals experienced 1.88 (95% CI 1.61 to 2.21) and 1.24 (95% CI 1.02 to 1.50) times the mortality rates in the age groups of 35-65 and >65 y, respectively. These findings indicate that gas-exposed individuals are likely to have a higher risk of severe COVID-19 and death and need to be specifically targeted and recognized for preventive and promotive efforts.

Synthesis of Novel Triazine-Based Chalcones and 8,9-dihydro-7H-pyrimido[4,5-b][1,4]diazepines as Potential Leads in the Search of Anticancer, Antibacterial and Antifungal Agents.

This study presents the synthesis of four series of novel hybrid chalcones (20,21)a-g and (23,24)a-g and six series of 1,3,5-triazine-based pyrimido[4,5-b][1,4]diazepines (28-33)a-g and the evaluation of their anticancer, antibacterial, antifungal, and cytotoxic properties. Chalcones 20b,d, 21a,b,d, 23a,d-g, 24a-g and the pyrimido[4,5-b][1,4]diazepines 29e,g, 30g, 31a,b,e-g, 33a,b,e-g exhibited outstanding anticancer activity against a panel of 60 cancer cell lines with GI50 values between 0.01 and 100 µM and LC50 values in the range of 4.09 µM to >100 µM, several of such derivatives showing higher activity than the standard drug 5-fluorouracil (5-FU). On the other hand, among the synthesized compounds, the best antibacterial properties against N. gonorrhoeae, S. aureus (ATCC 43300), and M. tuberculosis were exhibited by the pyrimido[4,5-b][1,4]diazepines (MICs: 0.25-62.5 µg/mL). The antifungal activity studies showed that triazinylamino-chalcone 29e and triazinyloxy-chalcone 31g were the most active compounds against T. rubrum and T. mentagrophytes and A. fumigatus, respectively (MICs = 62.5 µg/mL). Hemolytic activity studies and in silico toxicity analysis demonstrated that most of the compounds are safe.

Design, manufacturing and testing of a green non-isocyanate polyurethane prosthetic heart valve.

The sole effective treatment for most patients with heart valve disease is valve replacement by implantation of mechanical or biological prostheses. However, mechanical valves represent high risk of thromboembolism, and biological prostheses are prone to early degeneration. In this work, we aim to determine the potential of novel environmentally-friendly non-isocyanate polyurethanes (NIPUs) for manufacturing synthetic prosthetic heart valves. Polyhydroxyurethane (PHU) NIPUs are synthesized via an isocyanate-free route, tested in vitro, and used to produce aortic valves. PHU elastomers reinforced with a polyester mesh show mechanical properties similar to native valve leaflets. These NIPUs do not cause hemolysis. Interestingly, both platelet adhesion and contact activation-induced coagulation are strongly reduced on NIPU surfaces, indicating low thrombogenicity. Fibroblasts and endothelial cells maintain normal growth and shape after indirect contact with NIPUs. Fluid-structure interaction (FSI) allows modeling of the ideal valve design, with minimal shear stress on the leaflets. Injection-molded valves are tested in a pulse duplicator and show ISO-compliant hydrodynamic performance, comparable to clinically-used bioprostheses. Poly(tetrahydrofuran) (PTHF)-NIPU patches do not show any evidence of calcification over a period of 8 weeks. NIPUs are promising sustainable biomaterials for the manufacturing of improved prosthetic valves with low thrombogenicity.

Intramolecular Friedel-Crafts Acylation of [11C]Isocyanates Enabling the Radiolabeling of [carbonyl-11C]DPQ.

α,ß-aromatic lactams are highly abundant in biologically active molecules, yet so far they cannot be radiolabeled with short-lived (t1/2=20.3 min), ß+-decaying carbon-11, which has prevented their application as positron emission tomography tracers. Herein, we developed, optimized, and applied a widely applicable, one-pot, quick, robust and automatable radiolabeling method for α,ß-aromatic lactams starting from [11C]CO2 using the reagent POCl3⋅AlCl3. This method proceeds via intramolecular Friedel-Crafts acylation of in situ formed [11C]isocyanates and shows a broad substrate scope for the formation of five- and six-membered rings. We implemented our developed labeling method for the radiosynthesis of the potential PARP1 PET tracer [carbonyl-11C]DPQ in a clinical radiotracer production facility following the standards of the European Pharmacopoeia.

All-Natural Plant-Derived Polyurethane as a Substitute of a Petroleum-Based Polymer Coating Material.

The development of efficient, biobased polyurethane controlled-release fertilizers from sustainable and eco-friendly biomaterials has received increased research attention, owing to concerns regarding global food security and environmental sustainability. Most previous studies focused on replacing petroleum-based polyols with biopolyols; however, the other main raw material, isocyanate, remained a petrochemical product. Herein, all-natural, plant-derived polyurethane-coated urea was successfully developed using castor oil and biobased isocyanate, and the performance of the coating shell before and after modification was compared. The results showed that the incorporation of a low dose of lauric acid copper into the coating material simultaneously enhanced the hydrophobicity and elasticity of the all-biobased polyurethane membrane, which prolonged the nitrogen release longevity from 3 to 112 days. In addition, the modified membrane showed excellent biodegradability in a soil environment. The novel all-biobased polyurethane coating material and modification technique provide insight for developing sustainable and eco-friendly controlled-release fertilizers.

Synthesis of sydnonimines from sydnones and their use for bioorthogonal release of isocyanates in cells.

In this article, we report the synthesis of sydnonimines from sydnones and their use as dipoles for fast click-and-release reactions. The process relies on nucleophilic aromatic substitution of aliphatic and aromatic amines with triflated sydnones. This new methodology allowed the preparation of functionalised sydnonimine probes that are otherwise difficult to prepare. These probes were then used to release a drug and a fluorescent aromatic isocyanate inside living cells.

Lung Gene Expression Suggests Roles for Interferon-Stimulated Genes and Adenosine Deaminase Acting against RNA-1 in Pathologic Responses to Diisocyanate.

Mechanisms underlying methylene diphenyl diisocyanate (MDI) and other low molecular weight chemical-induced asthma are unclear and appear distinct from those of high molecular weight (HMW) allergen-induced asthma. We sought to elucidate molecular pathways that differentiate asthma-like pathogenic vs nonpathogenic responses to respiratory tract MDI exposure in a murine model. Lung gene expression differences in MDI exposed immune-sensitized and nonsensitized mice vs unexposed controls were measured by microarrays, and associated molecular pathways were identified through bioinformatic analyses and further compared with published studies of a prototypic HMW asthmagen (ovalbumin). Respiratory tract MDI exposure significantly altered lung gene expression in both nonsensitized and immune-sensitized mice, vs controls. Fifty-three gene transcripts were altered in all MDI exposed lung tissue vs controls, with levels up to 10-fold higher in immune-sensitized vs nonsensitized mice. Gene transcripts selectively increased in MDI exposed immune-sensitized animals were dominated by chitinases and chemokines and showed substantial overlap with those increased in ovalbumin-induced asthma. In contrast, MDI exposure of nonsensitized mice increased type I interferon stimulated genes (ISGs) in a pattern reflecting deficiency in adenosine deaminase acting against RNA (ADAR-1), an important regulator of innate, as well as "sterile" or autoimmunity triggered by tissue damage. Thus, MDI-induced changes in lung gene expression were identified that differentiate nonpathogenic innate responses in nonsensitized hosts from pathologic adaptive responses in immune-sensitized hosts. The data suggest that MDI alters unique biological pathways involving ISGs and ADAR-1, potentially explaining its unique immunogenicity/allergenicity.

[An epidemiological and evolutionary profile of occupational asthma of Tunisian workers]. / Profil épidémiologique et évolutif de l'asthme professionnel des travailleurs tunisiens.

INTRODUCTION: This study aims to identify the epidemiological and occupational characteristics of patients with occupational asthma (OA) and to assess their clinical evolution and occupational outcomes. METHODS: We carried out a descriptive epidemiological study over a period of five years (from 2012 to 2016) about the OA cases in the private sector reported in the Tunisian region of Zaghouan. RESULTS: All in all, 165 OA cases were reported during the study period, representing an annual incidence of 733.3 cases per 1,000,000 workers in the private sector. Our study population was composed predominantly (85.5%) of women, whose mean age was 41.5±6.8years. More than three quarters of the affected persons were working in the automobile industry, and most illnesses (77%) were attributable to isocyanates. The mean time to onset of the respiratory symptoms was longer for low molecular weight agents (13.6±3.1years) compared to high molecular weight agents (12.0±3.9years) (P=0.0006). The majority of OA cases (66.7%) lost their jobs. Job loss was significantly more frequent among asthmatic women and workers with OA due to isocyanates. Among the 62 cases of OA for whom risk factors were eliminated, 45 nonetheless remained symptomatic. CONCLUSION: Effective prevention strategies involving the various actors need to be implemented in work environments so as to reduce the frequency and the medico-legal repercussions of a disabling condition.

Linezolid brain penetration in neurointensive care patients.

BACKGROUND: Linezolid exposure in critically ill patients is associated with high inter-individual variability, potentially resulting in subtherapeutic antibiotic exposure. Linezolid exhibits good penetration into the CSF, but its penetration into cerebral interstitial fluid (ISF) is unknown. OBJECTIVES: To determine linezolid penetration into CSF and cerebral ISF of neurointensive care patients. PATIENTS AND METHODS: Five neurocritical care patients received 600 mg of linezolid IV twice daily for treatment of extracerebral infections. At steady state, blood and CSF samples were collected from arterial and ventricular catheters, and microdialysate was obtained from a cerebral intraparenchymal probe. RESULTS: The median fAUC0-24 was 57.6 (24.9-365) mg·h/L in plasma, 64.1 (43.5-306.1) mg·h/L in CSF, and 27.0 (10.7-217.6) mg·h/L in cerebral ISF. The median penetration ratio (fAUCbrain_or_CSF/fAUCplasma) was 0.5 (0.25-0.81) for cerebral ISF and 0.92 (0.79-1) for CSF. Cerebral ISF concentrations correlated well with plasma (R = 0.93, P < 0.001) and CSF levels (R = 0.93, P < 0.001).The median fAUC0-24/MIC ratio was ≥100 in plasma and CSF for MICs of ≤0.5 mg/L, and in cerebral ISF for MICs of ≤0.25 mg/L. The median fT>MIC was ≥80% of the dosing interval in CSF for MICs of ≤0.5 mg/L, and in plasma and cerebral ISF for MICs of ≤0.25 mg/L. CONCLUSIONS: Linezolid demonstrates a high degree of cerebral penetration, and brain concentrations correlate well with plasma and CSF levels. However, substantial variability in plasma levels, and thus cerebral concentrations, may result in subtherapeutic tissue concentrations in critically ill patients with standard dosing, necessitating therapeutic drug monitoring.

Design of 3D-Photoprintable, Bio-, and Hemocompatible Nonisocyanate Polyurethane Elastomers for Biomedical Implants.

Polyurethanes (PUs) have adjustable mechanical properties, making them suitable for a wide range of applications, including in the biomedical field. Historically, these PUs have been synthesized from isocyanates, which are toxic compounds to handle. This has encouraged the search for safer and more environmentally friendly synthetic routes, leading today to the production of nonisocyanate polyurethanes (NIPUs). Among these NIPUs, polyhydroxyurethanes (PHUs) bear additional hydroxyl groups, which are particularly attractive for derivatizing and adjusting their physicochemical properties. In this paper, polyether-based NIPU elastomers with variable stiffness are designed by functionalizing the hydroxyl groups of a poly(propylene glycol)-PHU by a cyclic carbonate carrying a pendant unsaturation, enabling them to be post-photo-cross-linked with polythiols (thiol-ene). Elastomers with remarkable mechanical properties whose stiffness can be adjusted are obtained. Thanks to the unique viscous properties of these PHU derivatives and their short gel times observed by rheology experiments, formulations for light-based three-dimensional (3D) printing have been developed. Objects were 3D-printed by digital light processing with a resolution down to the micrometer scale, demonstrating their ability to target various designs of prime importance for personalized medicine. In vitro biocompatibility tests have confirmed the noncytotoxicity of these materials for human fibroblasts. In vitro hemocompatibility tests have revealed that they do not induce hemolytic effects, they do not increase platelet adhesion, nor activate coagulation, demonstrating their potential for future applications in the cardiovascular field.

Recent developments in occupational asthma.

PURPOSE OF REVIEW: Occupational asthma (OA) is a complex condition that can be difficult to diagnose. The purpose of this review is to describe some recent findings regarding the epidemiology of OA, the occupational sensitizing agents, the prognosis of OA, and its primary prevention. RECENT FINDINGS: The risk of developing OA varies according to the geographic localization of the worker, the type of industry and the type of sensitizing agents. New findings have been reported for several known sensitizing agents, such as isocyanates, seafood & cleaning agents, and their related industries, such as hairdressing salons and schools. Moreover, a few new sensitizing agents, such as cannabis, have been identified in the past few years. The prognosis of OA seems worse than that of nonwork-related asthma. It is mainly determined by the duration and the level of exposure. Primary prevention is crucial to reduce the number of new cases of OA. Complete avoidance of exposure to the causal agent remains the optimal treatment of sensitizer-induced OA. SUMMARY: Improving our knowledge regarding OA and its causative agents is key to enable an early recognition of this condition and improve its prognosis. Further research is still needed to improve primary prevention.

Thermoplastic polyurethane/POSS nanohybrids: Synthesis, morphology, and biological properties.

Recent studies show good osteoinductive properties of polyurethanes modified with polyhedral oligomeric silsesquioxanes (POSS). In this work, three types of POSS; propanediolisobutyl-POSS (PHI-POSS), disilanolisobutyl-POSS (DSI-POSS), and octahydroxybutyl-POSS (OCTA-POSS) were chemically incorporated into linear polyurethane based on an aliphatic isocyanate, hexamethylene diisocyanate (HDI), to obtain new nanohybrid PU-POSS materials. The full conversion of POSS was confirmed by Fourier transform infrared spectroscopy (FTIR-ATR) spectra of the model reactions with pure HDI. The materials obtained were investigated by FTIR, SEM-EDS, and DSC. The DSC studies showed the thermoplasticity of the obtained materials and apparently good recovery. 30-day immersion in SBF (simulated body fluid) revealed an increase in the rate of deposition of hydroxyapatite (HAp) for the highest POSS loadings, resulting in thick layers of hydroxyapatite (~60-40 µm), and the Ca/P ratio 1.67 (even 1.785). The structure and properties of the inorganic layer depend on the type of POSS, the number of hard segments, and those containing POSS, which can be tailored by changing the HDI/poly(tetramethylene glycol) (PTMG) ratio. Furthermore, the obtained composites revealed good biocompatibility, as confirmed by cytotoxicity tests conducted on two cell lines; normal human dermal fibroblasts (NHDF) and primary human osteoblasts (HOB). Adherent cells seeded on the tested materials showed viability even after a 48-h incubation. After this time, the population of viable, and proliferating cells exceeded 90%. Bioimaging studies have shown the fibroblast and osteoblast cells were well attached to the surface of the tested materials.

Relief of Residual Stress in Bulk Thermosets in the Glassy State by Local Bond Exchange.

The covalently cross-linked network gives thermosets superior thermal, mechanical, and electrical properties, which, however, squarely makes the large residual stress that is inevitably induced during preparation hardly relieved in the glassy state. In this work, an incredible reduction in residual stress is successfully achieved in bulk thermosets in the glassy state through introducing highly dynamic thiocarbamate bonds by "click" reactions of thiols and isocyanates. Due to the excellent dynamic behaviors of thiocarbamate bonds, local network rearrangement is achieved through thermal stimulation, while the strong 3D cross-linked network is well maintained. Ultimately, a decrease by 44% in residual stress is detected by simply annealing samples at 30 °C below glass transition temperature (Tg), during which they could well maintain more than 98.4% of the storage modulus. After the annealing, more uniform residual stress distribution is also observed, showing a 32% decline in sample standard deviation. However, the residual stress of epoxy resin, a typical thermoset as a reference, changes little even after annealing at Tg. The results prove it a feasible strategy to reduce residual stress in bulk thermosets in the glassy state by introducing proper dynamic covalent bonds.

Direct ink writing of biocompatible chitosan/non-isocyanate polyurethane/cellulose nanofiber hydrogels for wound-healing applications.

The demand for new biocompatible and 3D printable materials for biomedical applications is on the rise. Ideally, such materials should exhibit either biodegradability or recyclability, possess antibacterial properties, and demonstrate remarkable biocompatibility with no cytotoxic effects. In this research, we synthesized biocompatible and 3D printable hydrogels tailored for biomedical applications, such as wound healing films, by combining antibacterial double-quaternized chitosan (DQC) with cystamine-based non-isocyanate polyurethane (NIPU-Cys) - a material renowned for enhancing both the flexibility and mechanical properties of the hydrogels. To improve the rheological behavior, swelling attributes, and printability, cellulose nanofibrils were introduced into the matrix. We investigated the impact of DQC on degradability, swelling capacity, rheological behavior, printability, and cell biocompatibility. The slightly cytotoxic nature associated with quaternary chitosan was evaluated, and the optimal concentration of DQC in the hydrogel was determined to ensure biocompatibility. The resulting hydrogels were found to be suitable materials for 3D printing via a direct ink writing technique (DIW), producing porous, biocompatible hydrogels endowed with valuable attributes suitable for various wound-healing applications.

A Novel Hydrophobic Polyimide Film with Sag Structure Derived from Multi-Hybrid Strategy.

Polyimide (PI) film with hydrophilic greatly limits their application in the field of microelectronic device packaging. A novel hydrophobic PI film with sag structure and improved mechanical properties is prepared relying on the reaction between anhydride-terminated isocyanate-based polyimide (PIY) containing a seven-membered ring structure and the amino-terminated polyamide acid (PAA) via multi-hybrid strategy, this work named it as hybrid PI film and marked it as PI-PIY-X. PI-PIY-30 showed excellent hydrophobic properties, and the water contact angle could reach to 102°, which is 20% and 55% higher than simply PI film and PIY film, respectively. The water absorption is only 1.02%, with a decrease of 49% and 53% compared with PI and PIY. Due to that the degradation of seven-membered ring and generation of carbon dioxide led to the formation of sag structure, the size of sag structures is ≈16.84 and 534.55 nm for in-plane and out-plane direction, which are observed on surface of PI-PIY-30. Meanwhile, PI-PIY-30 possessed improved mechanical properties, and the tensile strength is 109.08 MPa, with 5% and more than 56% higher than that of pure PI and PIY film, showing greatly application prospects in the field of integrated circuit.