Adhesion of Candida albicans on PTFE membranes used in guided bone regeneration.

OBJECTIVES: Guided bone regeneration (GBR) is a core procedure used to regenerate bone defects. The aim of the study was to investigate the adherence of Candida albicans on six commercially available polytetrafluoroethylene (PTFE) membranes used in GBR procedures and the subsequent clinical consequences. MATERIALS AND METHODS: Six commercially available PTFE membranes were tested. Two of the membranes had a textured surface and the other four a plane, nontextured one. C. albicans (ATCC 24433) was cultured for 24 h, and its cell surface hydrophobicity was assessed using a modified method. C. albicans adhesion to membrane discs was studied by scanning electron microscopy (SEM) and real-time polymerase chain reaction (PCR). RESULTS: C. albicans was found to be hydrophobic (77.25%). SEM analysis showed that C. albicans adherence to all membranes examined was characterized by patchy, scattered, and small clustered patterns except for one nontextured membrane with a most rough surface in which a thick biofilm was observed. Real-time PCR quantification revealed significantly greater adhesion of C. albicans cells to PTFE membranes than the control membrane (p ≤ .001) with the membranes having a textured surface exhibiting the highest count of 2680 × 104 cells/ml compared to the count of 707 × 104 cells/mL on those with a nontextured one (p ≤ .001). One membrane with nontextured surface, but with most rough surface was found to exhibit the highest count of 3010 × 104 cells/ml (p ≤ .05). CONCLUSION: The results of this study indicate that C. albicans adhesion on membranes' surfaces depends on the degree of surface roughness and/or on the presence of a texture. Textured PTFE membranes and/or membranes high roughness showed significantly more adhered C. albicans cells. These findings can impact the surgeon's choice of GBR membrane and postoperative maintenance.

Evaluation of PVC and PTFE filters for direct-on-filter crystalline silica quantification by FTIR.

Direct-on-Filter (DoF) analysis of respirable crystalline silica (RCS) by Fourier Transform Infrared (FTIR) spectroscopy is a useful tool for assessing exposure risks. With the RCS exposure limits becoming lower, it is important to characterize and reduce measurement uncertainties. This study systematically evaluated two filter types (i.e., polyvinyl chloride [PVC] and polytetrafluoroethylene [PTFE]) for RCS measurements by DoF FTIR spectroscopy, including the filter-to-filter and day-to-day variability of blank filter FTIR reference spectra, particle deposition patterns, filtration efficiencies, and pressure drops. For PVC filters sampled at a flow rate of 2.5 L/min for 8 h, the RCS limit of detection (LOD) was 7.4 µg/m3 when a designated laboratory reference filter was used to correct the absorption by the filter media. When the spectrum of the pre-sample filter (blank filter before dust sampling) was used for correction, the LOD could be up to 5.9 µg/m3. The PVC absorption increased linearly with reference filter mass, providing a means to correct the absorption differences between the pre-sample and reference filters. For PTFE, the LODs were 12 and 1.2 µg/m3 when a designated laboratory blank or the pre-sample filter spectrum was used for blank correction, respectively, indicating that using the pre-sample blank spectrum will reduce RCS quantification uncertainty. Both filter types exhibited a consistent radially symmetric deposition pattern when particles were collected using 3-piece cassettes, indicating that RCS can be quantified from a single measurement at the filter center. The most penetrating aerodynamic diameters were around 0.1 µm with filtration efficiencies ≥ 98.8% across the measured particle size range with low-pressure drops (0.2-0.3 kPa) at a flow rate of 2.5 L/min. This study concludes that either the PVC or the PTFE filters are suitable for RCS analysis by DoF FTIR, but proper methods are needed to account for the variability of blank absorption among different filters.

A self-powered droplet sensor based on a triboelectric nanogenerator toward the concentration of green tea polyphenols.

Self-powered liquid droplet sensors based on triboelectric nanogenerators have attracted extensive attention in the field of biochemical sensing applications. Numerous research studies have investigated the effects of factors such as molecular species, molecular concentration, molecular charge, and molecular dipole moment in solution on the output electrical signals of the sensor. In this study, we prepared a self-powered droplet sensor using conductive copper film tape, polytetrafluoroethylene, and conductive aluminum foil tape. The sensor can continuously output pulsed electrical signals with minimal environmental impact. In comparison with other types of sensors, this sensor boasts a rapid response time of 10 ms and excellent sensitivity. The relationship between the friction-induced output current and voltage of the droplets and the concentration of green tea polyphenols (GTPs) was studied using the self-powered liquid droplet sensor with five different green tea samples. It was found that GTPs were the main factor contributing to the changes in output electrical signals in green tea water droplets. Fluorescence spectroscopy was used to reveal that the magnitude of the output current was inversely proportional to the concentration of GTPs in green tea. These results demonstrate the potential application of self-powered liquid droplet sensors in biochemical sensing applications based on concentration-dependent output signals.

Effect of short-term sample storage and preparatory conditions on losses of 18 per- and polyfluoroalkyl substances (PFAS) to container materials.

There is a lack of agreement on a suitable container material for per- and polyfluoroalkyl substances (PFAS) analysis, particularly at trace levels. In this study, the losses of 18 short- and long-chain (C4-C10) PFAS to commonly used labware materials (high-density polyethylene (HDPE), polypropylene (PP), polystyrene (PS), polypropylene co-polymer (PPCO), polyethylene terephthalate (PET), polytetrafluoroethylene (PTFE), and glass were investigated. The influence of sample storage and preparation conditions, i.e., storage time, solvent composition, storage temperatures (4 °C and 20 °C), and sample agitation techniques (shaking and centrifugation) on PFAS losses to the container materials were investigated. The results showed higher losses for most of the considered PFAS (up to 50.9%) in 100% aqueous solutions after storage for 7 days regardless of the storage temperature compared to those after 3 days. Overall, the order of losses to different materials varied for individual PFAS, with the highest losses of long-chain PFAS observed to PP and HDPE after 7-day storage at room temperature. The addition of methanol to aqueous PFAS solutions reduced the losses of long-chain PFAS to all tested materials. The use of sample centrifugation and shaking did not influence the extent of losses for most of the PFAS in 80:20 water:methanol (%, v/v) to container materials except for 8:2 fluorotelomer sulfonic acid (8:2 FTS), 9-chlorohexadecafluoro-3-oxanone-1-sulfonic acid (9Cl-PF3ONS), perfluorodecanoic acid (PFDA) and 4:2 fluorotelomer sulfonic acid (4:2 FTS). This study demonstrates lower losses of both long- and short-chain PFAS to glass and PET. It also highlights the need for caution when deciding on sample preparatory steps and storage during the analysis of PFAS.

Fabrication of cobalt-iron Prussian blue analogues functionalized hybrid membranes for efficiently capturing Tl from water: Performance and mechanism.

As trace levels of thallium (Tl) in water are lethal to humans and ecosystems, it is essential to exploit advanced technologies for efficient Tl removal. In response to this concern, an innovative composite membrane was developed, incorporating polytetrafluoroethylene (PTFE) and featuring a dual-support system with polydopamine (PDA) and polyethyleneimine (PEI), along with bimetallic Prussian blue analogues (Co@Fe-PBAs) as co-supports. The composite membrane exhibited an exceptional Tl+-adsorption capacity (qm) of 186.1 mg g-1 when utilized for the treatment of water containing low concentration of Tl+ (0.5 mg⋅L-1). Transmission electron microscopy displayed the obvious Tl+ mapping inside the special hollow Co@Fe-PBAs crystals, demonstrating the deep intercalation of Tl+ via ion exchange and diffusion. The Tl+-adsorption capability of the composite membrane was not greatly affected by coexisting Na+, Ca2+ and Mg2+ as well as the tricky K+, indicating the excellent anti-interference. Co-doped PBAs enhanced ion exchange and intercalation of the composite membrane with Tl+ leading to excellent Tl+ removal efficiency. The composite membrane could efficiently remove Tl+ from thallium-contaminated river water to meet the USEPA standard. This study provides a cost-effective membrane-based solution for efficient Tl+ removal from Tl+-containing wastewater.

Performances of PTFE and PVDF membranes in achieving the discharge limit of mixed anodic oxidation coating wastewaters treated by membrane distillation.

The mixed wastewater generated by anodic oxidation coating facilities contains high levels of various contaminants, including iron, aluminum, conductivity, chemical oxygen demand (COD), and sulfate. In this study, the effectiveness of the membrane distillation (MD) process using polytetrafluoroethylene (PTFE) and polyvinylidene fluoride (PVDF) membranes was investigated to treat mixed wastewater from an anodized coating factory. The results indicate that both hydrophobic membranes effectively removed targeted contaminants. However, the PTFE membrane achieved higher removal efficiencies, with over 99% removal of sulfate, conductivity, iron, and aluminum, 85.7% of COD, and 86% of total organic carbon (TOC). In contrast, the PVDF membrane exhibited a significant decline in removal efficiency as the temperature increased and performed well only at lower feed temperatures. The PTFE membranes outperformed the PVDF membranes in treating chemically intensive anodic oxidation wastewaters. This superiority can be attributed to the PTFE membrane's morphology and structure, which are less influenced by feed water temperature and chemicals. Additionally, its slippery surface imparts anti-adhesion properties, effectively preventing membrane fouling, and maintaining the treated water quality and flux for longer operation time.

Effect of ultraviolet aged polytetrafluoroethylene microplastics on copper bioavailability and Microcystis aeruginosa growth.

Microplastics (MPs) are ubiquitous in aquatic environments, which can act as carriers to affect the bioavailability of heavy metals. The aging process in the environment changes the physicochemical properties of MPs, thereby affecting their environmental behavior and co-toxicity with other pollutants. However, relevant research is limited. In this study, we compared the properties and Cu2+ adsorption capacity of pristine and aged polytetrafluoroethylene (PTFE) MPs and further explored the influence on copper bioavailability and bio-effects on Microcystis aeruginosa. Aging process induced surface oxidation and cracks of PTFE MPs, and decreased the stability of MPs in water by increasing zeta potential. PTFE MPs had a strong adsorption capacity for Cu2+ and increased the bioavailability of copper to microalgae, which was not affected by the aging process. Pristine and aged PTFE MPs adhered to cyanobacterium surfaces and caused shrinkage and deformation of cells. Inhibition of cyanobacterium growth, photosynthesis and reduction of total antioxidant capacity were observed in the treatment of PTFE MPs. Combined exposure of pristine MPs and Cu2+ had stronger toxic effects to cyanobacterium, and increased Microcystin-LR release, which could cause harm to aquatic environment. Aging reduced the toxic effects of PTFE MPs on microalgae. Furthermore, soluble exopolysaccharide (EPS) content was significantly higher in co-exposure of aged MPs and Cu2+, which could reduce the toxicity to cyanobacterium cells. These results indicate that aging process alleviates the toxicity to microalgae and environmental risks caused by PTFE MPs. This study improves understanding of the combined toxicity of aged MPs and metals in freshwater ecosystems.

Adhesion-Lubrication Paradox of Articular Cartilage.

The friction of solids is primarily understood through the adhesive interactions between the surfaces. As a result, slick materials tend to be nonstick (e.g., Teflon), and sticky materials tend to produce high friction (e.g., tires and tape). Paradoxically, cartilage, the slippery bearing material of human joints, is also among the stickiest of known materials. This study aims to elucidate this apparent paradox. Cartilage is a biphasic material, and the most cited explanation is that both friction and adhesion increase as load transfers from the pressurized interstitial fluid to the solid matrix over time. In other words, cartilage is slippery and sticky under different times and conditions. This study challenges this explanation, demonstrating the strong adhesion of cartilage under high and low interstitial hydration conditions. Additionally, we find that cartilage clings to itself (a porous material) and Teflon (a nonstick material), as well as other surfaces. We conclude that the unusually strong interfacial tension produced by cartilage reflects suction (like a clingfish) rather than adhesion (like a gecko). This finding is surprising given its unusually large roughness, which typically allows for easy interfacial flow and defeats suction. The results provide compelling evidence that cartilage, like a clingfish, conforms to opposing surfaces and effectively seals submerged contacts. Further, we argue that interfacial sealing is itself a critical function, enabling cartilage to retain hydration, load support, and lubrication across long periods of inactivity.

Enhancing polytetrafluoroethylene (PTFE) coated film for food processing: Unveiling surface transformations through oxygenated plasma treatment and parameter optimization using response surface methodology.

Spray drying fruit juice powders poses challenges because sugars and organic acids with low molecular weight and a low glass transition temperature inherently cause stickiness. This study employed a hydrophobic polytetrafluoroethylene (PTFE) film to mimic the surface of the drying chamber wall. The Central Composite Design (CCD) using response surface methodology investigated the impact of power (X1, Watt) and the duration of oxygenated plasma treatment (X2, minutes) on substrate contact angle (°), reflecting surface hydrophobicity. To validate the approach, Morinda citrofolia (MC) juice, augmented with maltodextrins as drying agents, underwent spray drying on the improved PTFE-coated surface. The spray drying process for MC juice was performed at inlet air temperatures of 120, 140, and 160°C, along with Noni juice-to-maltodextrin solids ratios of 4.00, 1.00, and 0.25. The PTFE-coated borosilicate substrate, prepared at a radio frequency (RF) power of 90W for 15 minutes of treatment time, exhibited a porous and spongy microstructure, correlating with superior contact angle performance (171°) compared to untreated borosilicate glass. Optimization data indicated that the PTFE film attained an optimum contact angle of 146.0° with a specific combination of plasma RF operating power (X1 = 74 W) and treatment duration (X2 = 10.0 minutes). RAMAN spectroscopy indicated a structural analysis with an ID/IG ratio of 0.2, while Brunauer-Emmett-Teller (BET) surface area analysis suggested an average particle size of less than 100 nm for all coated films. The process significantly improved the powder's hygroscopicity, resistance to caking, and moisture content of maltodextrin-MC juice. Therefore, the discovery of this modification, which applies oxygen plasma treatment to PTFE-coated substrates, effectively enhances surface hydrophobicity, contact angle, porosity, roughness, and ultimately improves the efficacy and recovery of the spray drying process.

A self-assembly and cellular migration based fabrication of high-density 3D tubular constructs of barrier forming membranes.

Three-dimensional (3D) in vitro models, superior in simulating physiological conditions compared to 2D models, offer intricate cell-cell and cell-ECM interactions with diverse signaling cues like fluid shear stress and growth factor gradients. Yet, developing 3D tissue barrier models, specifically perfusable luminal structures with dense, multicellular constructs maintained for extended durations with oxygen and nutrients, remains a technical challenge. Here, we describe a molding-based approach for the fabrication of free-standing, perfusable, high cellular density tissue constructs using a self-assembly and migration process to form functional barriers. This technique utilizes a polytetrafluoroethylene (PTFE)-coated stainless-steel wire, held by stainless steel needles, as a template for a perfusable channel within an elongated PDMS well. Upon adding a bio-ink mix of cells and collagen, it self-assembles into a high cell density layer conformally around the wire. Removing the wire reveals a hollow construct, connectable to an inlet and outlet for perfusion. This scalable method allows creating varied dimensions and multicellular configurations. Notably, post-assembly, cells such as human umbilical vein endothelial cells (HUVECs) migrate to the surface and form functional barriers with adherens junctions. Permeability tests and fluorescence imaging confirm that these constructs closely mimic in vivo endothelial barrier permeability, exhibiting the lowest permeability among all in vitro models in the literature. Unlike traditional methods involving uneven post-seeding of endothelial cells leading to subpar barriers, our approach is a straightforward alternative for fabricating complex perfusable 3D tissue constructs and effective tissue barriers for use in various applications, including tissue engineering, drug screening, and disease modeling.

Crosslinking and fluorination reinforced PTFE nanofibrous membrane with excellent amphiphobic performance for low-scaling membrane distillations.

Membrane distillation (MD) has emerged as a promising technology for desalination and concentration of hypersaline brine. However, the efficient preparation of a structurally stable and salinity-resistant membrane remains a significant challenge. In this study, an amphiphobic polytetrafluoroethylene nanofibrous membrane (PTFE NFM) with exceptional resistance to scaling has been developed, using an energy-efficient method. This innovative approach avoids the high-temperature sintering treatment, only involving electrospinning with PTFE/PVA emulsion and subsequent low-temperature crosslinking and fluorination. The impact of the PVA and PTFE contents, as well as the crosslinking and subsequent fluorination on the morphology and MD performance of the NFM, were systematically investigated. The optimized PTFE NFM displayed robust amphiphobicity, boasting a water contact angle of 155.2º and an oil contact angle of 132.7º. Moreover, the PTFE NFM exhibited stable steam flux of 52.1 L·m-2·h-1 and 26.7 L·m-2·h-1 when fed with 3.5 wt % and 25.0 wt % NaCl solutions, respectively, and an excellent salt rejection performance (99.99 %, ΔT = 60 °C) in a continuous operation for 24 h, showing exceptional anti-scaling performance. It also exhibited stable anti-wetting and anti-fouling properties against surfactants (sodium dodecyl sulfate) and hydrophobic contaminants (diesel oil). These results underscore the significant potential of the PTFE nanofibrous membrane for practical applications in desalination, especially in hypersaline or polluted aqueous environments.

UV-C side-emitting optical fiber-based disinfection: a promising approach for infection control in tight channels.

The growth of pathogenic bacteria in moist and wet surfaces and tubing of medically relevant devices results in serious infections in immunocompromised patients. In this study, we investigated and demonstrated the successful implementation of a UV-C side-emitting optical fiber in disinfecting medically relevant pathogenic bacteria (Pseudomonas aeruginosa and Methicillin-resistant Staphylococcus aureus [MRSA]) within tight channels of polytetrafluoroethylene (PTFE). PTFE is a commonly used material both in point-of-use (POU) water treatment technologies and medical devices (dental unit water line [DUWL], endoscope). For a 1-m-long PTFE channel, up to ≥6 log inactivation was achieved using a 1-m-long UV side-emitting optical fiber (SEOF) with continuous 16-h exposure of low UV-C radiation ranging from ~0.23 to ~29.30 µW/cm2. Furthermore, a linear model was used to calculate the inhibition zone constant (k`), which enables us to establish a correlation between UV dosage and the extent of inactivated surface area (cm2) for surface-bound Escherichia coli on a nutrient-rich medium. The k` value for an irradiance ranging from ~150 to ~271.50 µW/cm2 was calculated to be 0.564 ± 0.6 cm·cm2/mJ. This study demonstrated the efficacy of SEOFs for disinfection of medically relevant microorganisms present in medically and domestically relevant tight channels. The impact of the results in this study extends to the optimization of operational efficiency in pre-existing UV surface disinfection setups that currently operate at UV dosages exceeding the optimal levels.IMPORTANCEGermicidal UV radiation has gained global recognition for its effectiveness in water and surface disinfection. Recently, various works have illustrated the benefit of using UV-C side-emitting optical fibers (SEOFs) for the disinfection of tight polytetrafluoroethylene (PTFE) channels. This study now demonstrates its impact for disinfection of medically relevant organisms and introduces critical design calculations needed for its implementation. The flexible geometry and controlled emission of light in these UV-SEOFs make them ideal for light distribution in tight channels. Moreover, the results presented in this manuscript provide a novel framework that can be employed in various applications, addressing microbial contamination and the disinfection of tight channels.

Mechanical characterization and torsional buckling of pediatric cardiovascular materials.

In complex cardiovascular surgical reconstructions, conduit materials that avoid possible large-scale structural deformations should be considered. A fundamental mode of mechanical complication is torsional buckling which occurs at the anastomosis site due to the mechanical instability, leading surgical conduit/patch surface deformation. The objective of this study is to investigate the torsional buckling behavior of commonly used materials and to develop a practical method for estimating the critical buckling rotation angle under physiological intramural vessel pressures. For this task, mechanical tests of four clinically approved materials, expanded polytetrafluoroethylene (ePTFE), Dacron, porcine and bovine pericardia, commonly used in pediatric cardiovascular surgeries, are conducted (n = 6). Torsional buckling initiation tests with n = 4 for the baseline case (L = 7.5 cm) and n = 3 for the validation of ePTFE (L = 15 cm) and Dacron (L = 15 cm and L = 25 cm) for each are also conducted at low venous pressures. A practical predictive formulation for the buckling potential is proposed using experimental observations and available theory. The relationship between the critical buckling rotation angle and the lumen pressure is determined by balancing the circumferential component of the compressive principal stress with the shear stress generated by the modified critical buckling torque, where the modified critical buckling torque depends linearly on the lumen pressure. While the proposed technique successfully predicted the critical rotation angle values lying within two standard deviations of the mean in the baseline case for all four materials at all lumen pressures, it could reliably predict the critical buckling rotation angles for ePTFE and Dacron samples of length 15 cm with maximum relative errors of 31% and 38%, respectively, in the validation phase. However, the validation of the performance of the technique demonstrated lower accuracy for Dacron samples of length 25 cm at higher pressure levels of 12 mmHg and 15 mmHg. Applicable to all surgical materials, this formulation enables surgeons to assess the torsional buckling potential of vascular conduits noninvasively. Bovine pericardium has been found to exhibit the highest stability, while Dacron (the lowest) and porcine pericardium have been identified as the least stable with the (unitless) torsional buckling resistance constants, 43,800, 12,300 and 14,000, respectively. There was no significant difference between ePTFE and Dacron, and between porcine and bovine pericardia. However, both porcine and bovine pericardia were found to be statistically different from ePTFE and Dacron individually (p < 0.0001). ePTFE exhibited highly nonlinear behavior across the entire strain range [0, 0.1] (or 10% elongation). The significant differences among the surgical materials reported here require special care in conduit construction and anastomosis design.

Polytetrafluorethylene added to acrylic resins: mechanical properties

The addition of different polymers, such as polytetrafluorethylene (PTFE), to denture base resins could be an option to modify acrylic resin mechanical properties. This study evaluated the surface hardness, impact and flexural strength, flexural modulus and peak load of 2 acrylic resins, one subjected to a long and another subjected to a short polymerization cycle, which were prepared with or without the addition of 2 percent PTFE. Four groups were formed according to the polymerization cycle and addition or not of PTFE. Forty specimens were prepared for each test (10 per group) with the following dimensions: hardness (30 mm diameter x 5 mm thick), impact strength (50 x 6 x 4 mm) and flexural strength (64 x 10 x 3.3 mm) test. The results of the flexural strength test allowed calculating flexural modulus and peak of load values. All tests were performed in accordance with the ISO 1567:1999 standard. Data were analyzed statistically by ANOVA and Tukey's test with the level of significance set at 5 percent. No statistically significant differences (p>0.05) were found for surface hardness. Flexural strength, impact strength and peak load were significantly higher (p<0.05) for resins without added PTFE. The flexural modulus of the acrylic resin with incorporated 2 percent PTFE polymerized by long cycle was significantly higher (p<0.05) than that of the other resins. Within the limits of this study, it may be concluded that the addition of PTFE did not improve the mechanical properties of the evaluated acrylic resins.

A adição de diferentes polímeros como o politetrafluoretileno (PTFE) às resinas para base de próteses removíveis pode ser uma opção para modificar as propriedades mecânicas das resinas acrílicas. Este estudo avaliou a dureza de superfície, a resistência ao impacto e à flexão, o módulo flexural e a carga de ruptura de duas resinas acrílicas, uma submetida ao ciclo longo e a outra ao ciclo curto de polimerização, as quais foram preparadas com ou sem a adição de PTFE a 2 por cento. Quatro grupos foram formados de acordo com os ciclos de polimerização e a adição ou não de PTFE. Quarenta espécimes foram preparados para cada teste (10 espécimes por grupo) com as seguintes dimensões: dureza de superfície (30 mm diametro x 5 mm espessura), resistência ao impacto (50 x 6 x 4 mm), resistência à flexão (64 x 10 x 3,3 mm). O módulo flexural e a carga de ruptura foram calculados a partir dos valores obtidos no teste de resistência à flexão. Todos os testes foram realizados em conformidade com a Norma ISO 1567:1999. Os dados foram submetidos à análise de variância e teste de Tukey com nível de significância de 5 por cento. Não foram encontradas diferenças estatisticamente significantes (p>0,05) para dureza de superfície. Os valores de resistência à flexão, resistência ao impacto e carga de ruptura foram maiores para as resinas sem a adição de PTFE (p<0,05). O valor do módulo flexural da resina acrílica com adição de PTFE a 2 por cento, polimerizada por ciclo longo, foi maior do que as outras resinas (p<0,05). Dentro das limitações deste estudo, pode-se concluir que a adição de politetrafluoretileno não melhorou as propriedades mecânicas das resinas acrílicas avaliadas.

Comparative analysis of the shrinkage stress of composite resins

The aim of this study was to compare the shrinkage stress of composite resins by three methods. In the first method, composites were inserted between two stainless steel plates. One of the plates was connected to a 20 kgf load cell of a universal testing machine (EMIC-DL-500). In the second method, disk-shaped cavities were prepared in 2-mm-thick Teflon molds and filled with the different composites. Gaps between the composites and molds formed after polymerization were evaluated microscopically. In the third method, the wall-to-wall shrinkage stress of the resins that were placed in bovine dentin cavities was evaluated. The gaps were measured microscopically. Data were analyzed by one-way ANOVA and Tukey's test (alpha=0.05). The obtained contraction forces were: Grandio = 12.18 ± 0.428N; Filtek Z 250 = 11.80 ± 0.760N; Filtek Supreme = 11.80 ± 0.707 N; and Admira = 11.89 ± 0.647 N. The gaps obtained between composites and Teflon molds were: Filtek Z 250 = 0.51 ± 0.0357 percent; Filtek Supreme = 0.36 ± 0.0438 percent; Admira = 0.25 ± 0.0346 percent and Grandio = 0.16 ± 0.008 percent. The gaps obtained in wall-to-wall contraction were: Filtek Z 250 = 11.33 ± 2.160 µm; Filtek Supreme = 10.66 ± 1.211µm; Admira = 11.16 ± 2.041 µm and Grandio = 10.50 ± 1.224 µm. There were no significant differences among the composite resins obtained with the first (shrinkage stress generated during polymerization) and third method (wall-to-wall shrinkage). The composite resins obtained with the second method (Teflon method) differed significantly regarding gap formation.

Comparison between textured silicone implants and those bonded with expanded polytetrafluoroethylene in rats

PURPOSE: Comparison of the inflammatory reaction promoted by textured silicone implants and that caused by the implant bonded with e-ptfe. METHODS: One-hundred and fifty rats were divided into three equal groups (control, silicone, and bonded e-ptfe). These groups were subdivided into five groups, according to the second operation, i.e., 7,30,60,90 and 180 days. Histology of the peri-implant tissue was analyzed by morphometry with blood count (neutrophilos, lymphocytes, macrophages, fibroblasts and capillaries). RESULTS: Comparison of subgroups 7,30,60,90, 180 days: - neutrophils: silicone: > in subgroup 7 days; bonded e-ptfe: > in subgroups 7 and 30 days; - lymphocytes: silicone: > in subgroup 7 and 180 days; bonded e-ptfe: > in subgroup 180 days; - macrophages: silicone: > in subgroup 7 and 60 days; bonded e-ptfe: > in subgroup 7,30 and 60 days; - fibroblasts: silicone: > in subgroup 30 and 60 days;- vascular volume: silicone: in subgroup 7, 60 and 90 days; bonded e-ptfe: > in subgroup 7 days. Comparison of groups: neutrophils : 7 days: > in silicone and bonded e-ptfe; 30 days: > in bonded e-ptfe; - lymphocytes: - 7,30,90 and 180 days: in the control; macrophages: - 7,30 and 60 days: > in silicone & bonded e-ptfe; 180 days > in silicone; fibroblasts: - 7,30 and 90 days: > in silicone and bonded e-ptfe; 180 days: > in bonded e-ptfe; vascular volume 7,60,90 and 180 days: > in silicone and bonded e-ptfe; 30 days: > in bonded e-ptfe. CONCLUSIONS: The acute stage of the inflammatory response was more severe and irregular in the silicone implant; both the silicone implant and the silicone bonded with e-ptfe promoted chronic inflammatory reaction and weak foreign body inflammatory response. These reactions were greater in the silicone implant group.

OBJETIVO: Comparar a reação inflamatória provocada pelo implante de silicone texturizado, com aquela causada por este recoberto com PTFE-E. MÉTODOS: Foram utilizadas 150 ratas, divididos em três grupos igruais (controle, silicone e recoberto PTFE-E). Os grupos foram subdivididos em cinco subgrupos, ou seja, 7, 30, 60, 90 e 180 dias, de acordo com a data do segundo ato operatório. O tecido perimplante foi analisado histologicamente, por meio de técnica morfométrica, com contagem de neutrófilos, linfócitos, macrófagos, fibroblastos e capilares. RESULTADOS: Comparação dos subgrupos 7, 30, 60, 90 180 dias: - neutrófilos - silicone: > no subgrupo 7 dias; rec-ptfe: > nos subgrupos 7 e 30 dias; - linfócitos: silicone: > no subgrupo 7 e 180 dias; rec-ptfe: > no subgrupo 180 dias; - macrófagos: silicone: > no subgrupo 7 e 60 dias; rec-ptfe: > no subgrupo 7, 30 e 60 dias; - fibroblastos: silicone: > no subgrupo 30 e 60 dias; - volume vascular: silicone: > no subrupo 7, 60 e 90 dias; rec-ptfe: > no subgrupo 7 dias . Comparação dos gurpos: - neutrófilos - 7 dias: > no silicone e rec-ptfe; 30 dias: > no rec-ptfe; - linfócitos - 7, 30, 90 e 180 dias: > no controle; - macrófagos - 7, 30 e 60 dias: > no silcone e rec-ptfe; 180 dias: > no silicone; - fibroblastos - 7, 30 e 90 dias: > no silicone e rec-ptfe; 180 dias: > no rec-ptfe; - volume vascular - 7, 60, 90 e 180 dias: > no silicone e rec-ptfe; 30 dias: > no rec-ptfe. CONCLUSÕES: A fase aguda da reação inflamatória foi mais intensa e irregular no implante de silicone; tanto o implante de silicone como o de silicone recoberto por ptfe-e induziram a reação inflamatória crônica e a fraca reação inflamatória tipo corpo estranho. Estas forram maiores no implante de silicone.

Surgarcane biopolymer patch in femoral artery angioplasty on dogs

PURPOSE: The objective of this study was to evaluate the use of the sugarcane biopolymer membrane in femoral artery patch angioplasty on dogs. METHODS: Eight dogs were submitted to bilateral femoral artery patch angioplasty with a sugarcane biopolymer membrane patch on one side and e-PTFE patch on the contralateral side. This research was performed at Experimental Surgical Research Laboratory of the Centro de Ciências da Saúde at Universidade Federal de Pernambuco. The dogs were submitted to a new surgery at 180 days after the patch angioplasty in order to harvest the femoral artery. All the animals were evaluated by: clinical examination, measure of femoral artery diameter, arteriogram and Doppler fluxometry. Yet the material harvested was sent to histological study. Each animal served as its own control. RESULTS: In all vessels of both groups there were no cases of infection, aneurysm formation, rupture or pseudoaneurysm formation and thrombosis. In both groups it was observed a chronic inflammatory reaction with lymphocytes, neutrophils and fibrosis in the outer surface of the patches. It was observed fibrosis in the inner surfaces of all the patches. In e-PTFE patches occurred invasion by fibroblasts. CONCLUSION: The sugarcane biopolymer membrane can be used as a patch in femoral artery angioplasty on dogs.

OBJETIVO: Avaliar a utilização da membrana do biopolímero de cana-de-açúcar quando utilizada como remendo em arterioplastias femorais de cães. MÉTODOS: Oito cães foram submetidos a arterioplastia femoral bilateral com enxertos em remendo com a membrana do biopolímero de cana-de-açúcar em um lado e com a prótese de e-PTFE no lado contra-lateral. Os experimentos foram realizados no Núcleo de Cirurgia Experimental do Centro de Ciências da Saúde da Universidade Federal de Pernambuco. A avaliação dos animais foi realizada através do exame clínico, da medida do diâmetro das artérias femorais, da fluxometria Doppler, da arteriografia e da histologia. Após 180 dias os cães foram submetidos a nova cirurgia para retirada dos segmentos das artérias femorais com os implantes. RESULTADOS: No período de avaliação nos dois grupos, não se observou casos de infecção, dilatação, ruptura ou falso-aneurisma e trombose. Nos dois grupos foi encontrada uma resposta inflamatória crônica com neutrófilos, linfócitos e fibrose na superfície externa dos remendos. Foi observada também a presença de fibrose na superfície interna em ambos os grupos. No grupo controle ocorreu invasão dos remendos de e-PTFE por fibroblastos. CONCLUSÃO: A membrana do biopolímero de cana-de-açúcar pode ser utilizada como remendo em arterioplastias femorais de cães.

Regeneración ósea guiada de cara al año 2000. Consideraciones clínicas y biológicas / Guided bone regeneration facing the year 2000. Clinical and biologic considerations

La regeneración ósea guiada representa hoy una de las terapias de mayor éxito para el manejo conjunto a la colocación de implantes. Durante los últimos años el uso de membranas para la regeneración ósea ha ido combinada desde membranas no reabsorbibles hasta membranas reabsorbibles. El presente artículo pretende mostrar a fondo los diferentes tipos de membranas que se tienen en el mercado, así como los resultados mostrados con el uso de las mismas. Asimismo, se hace un ligero repaso de las indicaciones para la regeneración ósea guiada y las propiedades que debe tener una membrana para poder ser utilizada en la regeneración ósea guiada

Nuevos enfoques en cirugía perirradicular: revisión de la literatura / New approaches in periradicular surgery: review of the literature

Cuando se genera una lesión periapical como consecuencia de un proceso inflamatorio crónico y posterior necrosis pulpar, se hace necesaria una terapia encaminada a eliminar el agente etiológico primario, lo que frecuentemente se resuelve exitosamente con un tratamiento endodóntico convencional. Sin embargo, en algunas casos persiste un estado inflamatorio manifestándose una patología periapical, que puede ser un granuloma o quiste perirradicular con o sin presencia de tractos sinuosos. Cuando la infección no puede ser erradicada por vía ortógrada, está indicada una cirugía endodóntica. La regeneración del defecto óseo periapical a veces no se da debido a migración del epitelio bucal o del tejido conjuntivo gingival hacia el defecto óseo, evitando la formación de hueso trabecular normal y haciendo necesarias nuevas cirugías de reentrada. La literatura reporta recientes materiales de obturación radicular terminal y elementos de regeneración tisular guiada para mejorar la predecibilidad del tratamiento quirúrgico. Sustituyendo la amalgama como material convencional de relleno transapical se encuentran actualmente los nuevos materiales derivados del óxido de zinc y eugenol (IRM y Super EBA) y últimamente el MTA o agregado de trióxidos minerales y como materiales de RTG se encuentran membranas bioabsorbibles, materiales sustitutos de hueso (hidroxiapatitas, hueso liofilizado) e injertos de periostio autólogo libres y pediculados