RESUMO
Objective: This study aims to develop a medical patch surface material featuring a microporous polyurethane (PU) membrane and to assess the material's properties and biological performance. The goal is to enhance the clinical applicability of pelvic floor repair patch materials. Methods: PU films with a microporous surface were prepared using PU prepolymer foaming technology. The films were produced by optimizing the PU prepolymer isocyanate index (R value) and the relative humidity (RH) of the foaming environment. The surface morphology of the PU microporous films was observed by scanning electron microscopy, and the chemical properties of the PU microporous films, including hydrophilicity, were analyzed using infrared spectroscopy, Raman spectroscopy, and water contact angle measurements. In vitro evaluations included testing the effects of PU microporous film extracts on the proliferation of L929 mouse fibroblasts and observing the adhesion and morphology of these fibroblasts. Additionally, the effect of the PU microporous films on RAW264.7 mouse macrophages was studied. Immune response and tissue regeneration were assessed in vivo using Sprague Dawley (SD) rats. Results: The PU films exhibited a well-defined and uniform microporous structure when the R value of PU prepolymer=1.5 and the foaming environment RH=70%. The chemical structure of the PU microporous films was not significantly altered compared to the PU films, with a significantly lower water contact angle ([55.7±1.5]° ) compared to PU films ([69.5±1.7]° ) and polypropylene (PP) ([ 104.3±2.5]°), indicating superior hydrophilicity. The extracts from PU microporous films demonstrated good in vitro biocompatibility, promoting the proliferation of L929 mouse fibroblasts. The surface morphology of the PU microporous films facilitated fibroblast adhesion and spreading. The films also inhibited the secretion of tumor necrosis factor-α (TNF-α) and interleukin (IL)-1ß by RAW264.7 macrophages while enhancing IL-10 and IL-4 secretion. Compared to 24 hours, after 72 hours of culture, the expression levels of TNF-α and IL-1ß were reduced in both the PU film and PU microporous film groups and were significantly lower than those in the PP film group (P<0.05), with the most notable decreases observed in the PU microporous film group. IL-10 and IL-4 levels increased significantly in the PU microporous film group, surpassing those in the PP film group (P<0.01), with the most pronounced increase in IL-4. The PU microporous film induced mild inflammation with no significant fibrous capsule formation in vivo. After 60 days of implantation, the film partially degraded, showing extensive collagen fiber growth and muscle formation in its central region. Conclusion: The PU microporous film exhibits good hydrophilicity and biocompatibility. Its surface morphology enhances cell adhesion, regulates the function of RAW264.7 macrophages, and promotes tissue repair, offering new insights for the design of pelvic floor repair and reconstruction patch materials.
Assuntos
Fibroblastos , Polipropilenos , Poliuretanos , Ratos Sprague-Dawley , Poliuretanos/química , Animais , Camundongos , Ratos , Polipropilenos/química , Fibroblastos/citologia , Materiais Biocompatíveis/química , Telas Cirúrgicas , Células RAW 264.7 , Propriedades de Superfície , Linhagem Celular , Porosidade , Teste de Materiais , Proliferação de Células/efeitos dos fármacos , Macrófagos/citologiaRESUMO
Objective: To investigate the biological safety of commercially available natural rubber latex and synthetic polyurethane condoms. Methods: Natural rubber latex condom brands of A1 and A2 and polyurethane condom brands of B1 and B2 were purchased from large chain pharmacies in Chengdu, with three packages randomly selected for each brand. The study assessed the toxic effects of condom extracts on L-929 mouse fibroblasts according to GB/T standards. Gross observation and histopathological evaluation were conducted to assess the irritation reactions of condoms on the vagina and penis of rabbits (3 rabbits were used for each brand), as well as their sensitization effects on guinea pig skin. Additionally, the impact of continuous perfusion of condom extracts of the vaginas of SD rats for 30 days on their reproductive systems was evaluated, following GB/T standards (5 rats were used for each brand). Results: Extracts from natural rubber latex condom brands A1 and A2, at concentrations of 100% and 50%, exhibited significant cytotoxicity, with optical density (OD) values being significantly lower than those of the blank control group and the polyurethane condom brands B1 and B2 (P<0.01). There was no significant difference in cell morphology and OD values between the extracts of B1 and B2 and the blank control group (P>0.05). Vaginal congestion was found in 3 rabbits from A1 group and 1 rabbit from the A2 group, while no obvious congestion was noted in rabbits from the B1 and the B2 groups. Histopathological examination showed scattered inflammatory cell infiltration in the vaginal tissue of 3 rabbits from the A1 group and 2 rabbits from the A2 group, and slight congestion in the blood vessels of the lamina propria. No obvious pathological changes were observed in the vaginal tissue of polyurethane brand rabbits. Two rabbits from the A1 group and 1 rabbit from the A2 group showed transient and mild erythema on the penis during the experiment. Histopathological examination showed that 1 rabbit from A1 group had small foci of pericapillary lymphocytes in the dermis of the penis, while no significant pathological changes were observed in the penile tissue of A2, B1, and B2 groups. After 30 days of continuous vaginal perfusion with condom extract, 3 rats in A1 group and 2 rats in the A2 group had uterine congestion, with the degree of congestion being lower in the A2 group. No significant congestion or pathological changes were observed in the vaginal and penile tissues of rabbits, or in the uterine tissues of rats from the polyurethane groups. None of the 4 groups of guinea pigs showed significant skin allergic reactions to the condom extracts. Conclusion: Significant differences in biosafety exist among condoms of various materials and brands. To ensure product safety, it is crucial to strengthen quality control and regulatory oversight after condoms become commercially available.
Assuntos
Preservativos , Látex , Poliuretanos , Ratos Sprague-Dawley , Animais , Coelhos , Feminino , Cobaias , Ratos , Masculino , Látex/química , Camundongos , Vagina/patologia , Fibroblastos/efeitos dos fármacos , Teste de Materiais , Borracha/efeitos adversosRESUMO
In this study, we present a novel approach to injection molding, focusing on the strength of weld lines in polyamide 6 (PA6) composite samples. By implementing a mold temperature significantly higher than the typical molding practice, which rarely exceeds 100°C, we assess the effects of advanced mold temperature management. The research introduces a newly engineered mold structure specifically designed for localized mold heating, distinguishing it as the 'novel cavity.' This innovative design is compared against traditional molding methods to highlight the improvements in weld line strength at elevated mold temperatures. To optimize the molding parameters, we apply an Artificial Neural Network (ANN) in conjunction with a Genetic Algorithm (GA). Our findings reveal that the optimal ultimate tensile strength (UTS) and elongation values are achieved with a filling time of 3.4 seconds, packing time of 0.8 seconds, melt temperature of 246°C, and a novel high mold temperature of 173°C. A specific sample demonstrated the best molding parameters at a filling time of 3.4 seconds, packing time of 0.4 seconds, melt temperature of 244°C, and mold temperature of 173°C, resulting in an elongation value of 582.6% and a UTS of 62.3 MPa. The most influential factor on the PA6 sample's UTS and elongation at the weld line was found to be the melt temperature, while the filling time had the least impact. SEM analysis of the fracture surfaces revealed ductile fractures with rough surfaces and grooves, indicative of the weld line areas' bonding quality. These insights pave the way for significant improvements in injection molding conditions, potentially revolutionizing the manufacturing process by enhancing the structural integrity of the weld lines in molded PA6 samples.
Assuntos
Nylons , Nylons/química , Temperatura , Resistência à Tração , Redes Neurais de Computação , Gases/química , Plásticos/química , Teste de Materiais , Caprolactama/química , Caprolactama/análogos & derivados , Algoritmos , PolímerosRESUMO
The human head can sometimes experience impact loads that result in skull fractures or other injuries, leading to the need for a craniectomy. Cranioplasty is a procedure that involves replacing the removed portion with either autologous bone or alloplastic material. While titanium has traditionally been the preferred material for cranial implants due to its excellent properties and biocompatibility, its limitations have prompted the search for alternative materials. This research aimed to explore alternative materials to titanium for cranial implants in order to address the limitations of titanium implants and improve the performance of the cranioplasty process. A 3D model of a defective skull was reconstructed with a cranial implant, and the implant was simulated using various stiff and soft materials (such as alumina, zirconia, hydroxyapatite, zirconia-reinforced PMMA, and PMMA) as alternatives to titanium under 2000N impact forces. Alumina and zirconia implants were found to reduce stresses and strains on the skull and brain compared to titanium implants. However, PMMA implants showed potential for causing skull damage under current loading conditions. Additionally, PMMA and hydroxyapatite implants were prone to fracture. Despite these findings, none of the implants exceeded the limits for tensile and compressive stresses and strains on the brain. Zirconia-reinforced PMMA implants were also shown to reduce stresses and strains on the skull and brain compared to PMMA implants. Alumina and zirconia show promise as alternatives to titanium for the production of cranial implants. The use of alternative implant materials to titanium has the potential to enhance the success of cranial reconstruction by overcoming the limitations associated with titanium implants.
Assuntos
Materiais Biocompatíveis , Análise de Elementos Finitos , Teste de Materiais , Procedimentos de Cirurgia Plástica , Crânio , Estresse Mecânico , Titânio , Zircônio , Humanos , Crânio/cirurgia , Titânio/química , Materiais Biocompatíveis/química , Zircônio/química , Procedimentos de Cirurgia Plástica/métodos , Próteses e Implantes , Durapatita/química , Polimetil Metacrilato/química , Óxido de Alumínio/química , Resistência à Tração , Fraturas Cranianas/cirurgia , Força CompressivaRESUMO
It's imperative to create a more ideal biological scaffold for bone defect repair. Calcium phosphate bone cements (CPC) could be used as a scaffold. Some ingredients and osteogenic factors could be added to improve its poor mechanical properties and biological activity. As a macromolecule extracted from traditional Chinese medicine, Hedysarum polysaccharides (HPS) would significantly promote the osteogenic activity of bone biomaterials. Zirconium oxide and starch were added to the solid phase and citric acid was added to the liquid phase to optimize CPC. HPS was loaded onto the scaffold as an osteogenic factor, and the prepared CPS + HPS was characterized. Further, the cytocompatibility of CPS + HPS was assessed according to activity, differentiation, and calcification in neonatal rat calvarial osteoblasts, and the biosafety of CPS + HPS was evaluated according to acute toxicity, pyrogen, sensitization, and hemolysis. The success of CPS + HPS in repairing bone defects was evaluated by using a rabbit femur implantation experiment. After optimization, CPS-20-CA-5 containing 10% starch and 5% citric acid displayed the highest mechanical strength of 28.96 ± 0.03 MPa. HPS-50 was demonstrated to exert the best osteogenic effect. The combination of CPS + HPS achieved HPS-loaded CPC. Material characterization, cytocompatibility, biosafety, and femoral implantation experiments indicated that CPS + HPS possessed better pressure resistance and improved osteogenic ability in bone defect repair.CPS + HPS demonstrated effective pressure resistance and superior osteogenic ability, which may be of great significance for bone defects and bone tissue engineering to promote bone regeneration and repair.
Assuntos
Cimentos Ósseos , Regeneração Óssea , Fosfatos de Cálcio , Osteogênese , Polissacarídeos , Alicerces Teciduais , Animais , Fosfatos de Cálcio/química , Cimentos Ósseos/química , Cimentos Ósseos/farmacologia , Coelhos , Polissacarídeos/química , Ratos , Alicerces Teciduais/química , Osteogênese/efeitos dos fármacos , Regeneração Óssea/efeitos dos fármacos , Osteoblastos/efeitos dos fármacos , Teste de Materiais , Materiais Biocompatíveis/química , Materiais Biocompatíveis/farmacologia , Ratos Sprague-Dawley , Masculino , Zircônio/química , Engenharia Tecidual/métodos , Fêmur/patologiaRESUMO
Diamond-like Carbon (DLC) has been used as a coating material of choice for a variety of technological applications owing to its favorable bio-tribo-thermo-mechanical characteristics. Here, the possibility of bringing DLC into orthopedic joint implants is examined. With ever increasing number of patients suffering from osteoarthritis as well as with the ingress of the osteoarthritic joints' malaise into younger and more active demographics, there is a pressing need to augment the performance and integrity of conventional total joint replacements (TJRs). Contemporary joint replacement devices use metal-on-polymer articulations to restore function to worn, damaged or diseased cartilage. The wear of polymeric components has been addressed using crosslinking and antioxidants; however, in the context of the metallic components, complications pertaining to corrosion and metal ion release inside the body still persist. Through this review article, we explore the use of DLC coatings on metallic bearing surfaces and elucidate why this technology might be a viable solution for ongoing electrochemical challenges in orthopedics. The different characteristics of DLC coatings and their feasibility in TJRs are examined through assessment of tribo-material characterization methods. A holistic characterization of the coating-substrate interface and the wear performance of such systems are discussed. As with all biomaterials used in TJRs, we need mindful consideration of potential in-vivo challenges. We present a few caveats for DLC coatings including delamination, hydrophobicity, and other conflicting as well as outdating findings in the literature. We recommend prudently exploring DLC films as potential coatings on metallic TJR components to solve the problems pertaining to wear, metal ion release, and corrosion. Ultimately, we advise bringing DLC into clinical use only after addressing all challenges and concerns outlined in this article.
Assuntos
Carbono , Materiais Revestidos Biocompatíveis , Diamante , Teste de Materiais , Humanos , Diamante/química , Materiais Revestidos Biocompatíveis/química , Carbono/química , Artroplastia de Substituição , Estudos de Viabilidade , Prótese Articular , Propriedades de Superfície , Corrosão , Desenho de Prótese , Metais/química , Osteoartrite/cirurgia , Materiais Biocompatíveis/químicaRESUMO
BACKGROUND: This study aimed to compare the in vitro shear bond strength (SBS) of mineral trioxide aggregate (MTA) and dual-cured, resin-modified calcium silicate material (Theracal PT) to composite resin, compomer, and bulk-fill composite, and to evaluate the bond failure mode under a stereomicroscope. METHODS: Ninety acrylic specimens, each with a 4 mm diameter and 2 mm height central hole, were prepared. These specimens were randomly divided into two groups based on the capping materials: MTA and Theracal PT. Each group was further subdivided into three subgroups (n = 15) according to the restorative materials: composite resin, compomer, and bulk-fill composite. The specimens were then subjected to shear testing using a universal testing machine at a crosshead speed of 1 mm/min. Post-test, the fracture locations were examined using a stereomicroscope. Data were analyzed using a two-way analysis of variance (ANOVA) and the Tukey test. RESULTS: The SBS values for the Theracal PT group were significantly higher than those for the MTA group (p < 0.001). Within the MTA groups, no significant differences were observed in SBS values across the different restorative materials. However, a significant difference was found between the mean SBS values of the Theracal PT + composite resin group and the Theracal PT + compomer group (p < 0.001). CONCLUSIONS: Theracal PT shows promise in dentistry due to its superior bond strength. Given its bond values, Theracal PT appears capable of forming durable and long-lasting restorations by establishing reliable bonds with various restorative materials commonly used in dentistry.
Assuntos
Compostos de Alumínio , Compostos de Cálcio , Resinas Compostas , Colagem Dentária , Análise do Estresse Dentário , Combinação de Medicamentos , Teste de Materiais , Óxidos , Resistência ao Cisalhamento , Silicatos , Compostos de Cálcio/química , Silicatos/química , Compostos de Alumínio/química , Óxidos/química , Resinas Compostas/química , Colagem Dentária/métodos , Materiais Dentários/química , Compômeros/química , Técnicas In VitroRESUMO
Quantifying the mechanical behavior of skin has been foundational in applications of cosmetics, surgical techniques, forensic science, and protective clothing development. However, previous puncture studies have lacked consistent and physiological boundary conditions of skin. To determine natural skin tension, excision of in situ porcine skin resulted in significantly different diameter reduction (shrinkage) in leg (19.5 %) and abdominal skin (38.4 %) compared to flank skin (28.5 %) (p = 0.047). To examine effects of initial tension and pre-conditioning, five conditions of initial tension (as percentage of diameter increase) and pre-conditioning were tested in quasistatic puncture with a 5 mm spherical impactor using an electrohydraulic load frame and custom clamping apparatus. Samples with less than 5 % initial tension resulted in significantly greater (p = 0.011) force at failure (279.2 N) compared to samples with greater than 25 % initial tension (195.1 N). Eight pre-conditioning cycles of 15 mm displacement reduced hysteresis by 45 %. The coefficient of variance was substantially reduced for force, force normalized by cutis thickness, displacement, stiffness, and strain energy up to 46 %. Pre-conditioned samples at physiological initial tension (14-25 %) resulted in significantly greater (p = 0.03) normalized forces at failure (278.3 N/mm) compared to non-conditioned samples of the same initial tension (234.4 N/mm). Pre-conditioned samples with 14-25 % initial tension, representing physiological boundary conditions, resulted in the most appropriate failure thresholds with the least variation. For in vitro puncture studies, the magnitude of applied initial tension should be defined based on anatomical location, through a shrinkage experimentation, to match natural tension of skin. Characterizing the biological behavior and tolerances of skin may be utilized in finite element models to aid in protective clothing development and forensic science analyses.
Assuntos
Pele , Animais , Suínos , Teste de Materiais , Fenômenos Biomecânicos , Punções , Fenômenos Mecânicos , Estresse Mecânico , Fenômenos Fisiológicos da Pele , Testes MecânicosRESUMO
In addition to human donor bones, bone models made of synthetic materials are the gold standard substitutes for biomechanical testing of osteosyntheses. However, commercially available artificial bone models are not able to adequately reproduce the mechanical properties of human bone, especially not human osteoporotic bone. To overcome this issue, new types of polyurethane-based synthetic osteoporotic bone models have been developed. Its base materials for the cancellous bone portion and for the cortical portion have already been morphologically and mechanically validated against human bone. Thus, the aim of this study was to combine the two validated base materials for the two bone components to produce femur models with real human geometry, one with a hollow intramedullary canal and one with an intramedullary canal filled with synthetic cancellous bone, and mechanically validate them in comparison to fresh frozen human bone. These custom-made synthetic bone models were fabricated from a computer-tomography data set in a 2-step casting process to achieve not only the real geometry but also realistic cortical thicknesses of the femur. The synthetic bones were tested for axial compression, four-point bending in two planes, and torsion and validated against human osteoporotic bone. The results showed that the mechanical properties of the polyurethane-based synthetic bone models with hollow intramedullary canals are in the range of those of the human osteoporotic femur. Both, the femur models with the hollow and spongy-bone-filled intramedullary canal, showed no substantial differences in bending stiffness and axial compression stiffness compared to human osteoporotic bone. Torsional stiffnesses were slightly higher but within the range of human osteoporotic femurs. Concluding, this study shows that the innovative polyurethane-based femur models are comparable to human bones in terms of bending, axial compression, and torsional stiffness.
Assuntos
Força Compressiva , Fêmur , Teste de Materiais , Osteoporose , Poliuretanos , Poliuretanos/química , Humanos , Fêmur/diagnóstico por imagem , Fêmur/fisiopatologia , Fenômenos Biomecânicos , Osteoporose/diagnóstico por imagem , Osteoporose/fisiopatologia , Testes MecânicosRESUMO
This study delves into the potential of amorphous titanium oxide (aTiO2) nano-coating to enhance various critical aspects of non-Ti-based metallic orthopedic implants. These implants, such as medical-grade stainless steel (SS), are widely used for orthopedic devices that demand high strength and durability. The aTiO2nano-coating, deposited via magnetron sputtering, is a unique attempt to improve the osteogenesis, the inflammatory response, and to reduce bacterial colonization on SS substrates. The study characterized the nanocoated surfaces (SS-a TiO2) in topography, roughness, wettability, and chemical composition. Comparative samples included uncoated SS and sandblasted/acid-etched Ti substrates (Ti). The biological effects were assessed using human mesenchymal stem cells (MSCs) and primary murine macrophages. Bacterial tests were carried out with two aerobic pathogens (S. aureusandS. epidermidis) and an anaerobic bacterial consortium representing an oral dental biofilm. Results from this study provide strong evidence of the positive effects of the aTiO2nano-coating on SS surfaces. The coating enhanced MSC osteoblastic differentiation and exhibited a response similar to that observed on Ti surfaces. Macrophages cultured on aTiO2nano-coating and Ti surfaces showed comparable anti-inflammatory phenotypes. Most significantly, a reduction in bacterial colonization across tested species was observed compared to uncoated SS substrates, further supporting the potential of aTiO2nano-coating in biomedical applications. The findings underscore the potential of magnetron-sputtering deposition of aTiO2nano-coating on non-Ti metallic surfaces such as medical-grade SS as a viable strategy to enhance osteoinductive factors and decrease pathogenic bacterial adhesion. This could significantly improve the performance of metallic-based biomedical devices beyond titanium.
Assuntos
Materiais Revestidos Biocompatíveis , Macrófagos , Teste de Materiais , Células-Tronco Mesenquimais , Osteogênese , Aço Inoxidável , Propriedades de Superfície , Titânio , Titânio/química , Aço Inoxidável/química , Animais , Humanos , Células-Tronco Mesenquimais/citologia , Camundongos , Materiais Revestidos Biocompatíveis/química , Materiais Revestidos Biocompatíveis/farmacologia , Macrófagos/metabolismo , Osteogênese/efeitos dos fármacos , Diferenciação Celular , Próteses e Implantes , Osteoblastos/citologia , Staphylococcus aureus/efeitos dos fármacos , Biofilmes , Staphylococcus epidermidis/efeitos dos fármacos , Aderência Bacteriana , MolhabilidadeRESUMO
In view of the special engineering properties of red clay and the waste of phosphogypsum resources, the expansion and contraction deformation and fissure evolution of phosphogypsum stabilized red clay under different conditions were investigated by laboratory tests and image processing system. The research results show that: (1) the absolute expansion and absolute shrinkage of phosphogypsum stabilized red clay are positively correlated with the compaction degree, the number of dry and wet cycles and the cement dosage, and negatively correlated with the initial water content and the phosphogypsum dosage; (2) the fissure rate increases with the increase of the number of dry and wet cycles, and decreases with the increase of the initial water content, the compaction degree, the cement, and the phosphogypsum dosage; (3) The relationship among absolute expansion rate (absolute shrinkage), degree of compaction and fracture rate can be fitted by the equation f(x,y) = ax+by+cx2+dy2+e; (4) Phosphogypsum has an obvious inhibiting effect on the expansion, shrinkage and cracking of the mix. It is recommended that the cement mixing amount of 6% and phosphogypsum: red clay = 1:1~1:2 as roadbed filler.
Assuntos
Silicatos de Alumínio , Sulfato de Cálcio , Argila , Materiais de Construção , Fósforo , Sulfato de Cálcio/química , Argila/química , Fósforo/química , Silicatos de Alumínio/química , Água/química , Teste de MateriaisRESUMO
BACKGROUND: Effects of the aging process on the flexural strength of Y-TZP and different Y-PSZ ceramics of different thicknesses were investigated. METHODS: 300 disc-shaped samples (12 mm diameter, 0.8 and 1.5 mm thicknesses) were made from 5 different zirconia materials 3Y-TZP LA, 4Y-PSZ, 5Y-PSZ, 3 + 5Y-PSZ and 4 + 5Y-PSZ. Experimental groups were artificially aged in an autoclave at 134 °C, 2 bar pressure for 1 and 5 h; control groups were not subjected to any treatment. Microstructural analysis was conducted using Scanning Electron Microscopy, and X-Ray Diffraction analysis determined the crystalline phase content. The impact of aging on flexural strength was investigated with the use of the biaxial flexural strength test. Data were analyzed using three-way ANOVA tests with a significance level of p < 0.05, applying Bonferroni correction for multiple comparisons. RESULTS: Statistically significant differences in flexural strength were observed among the materials and the material thicknesses (p < 0.05), while there were no significant differences among the aging times (p > 0.05). The highest mean flexural strength values were recorded in the case of the 3 Y-TZP-1.5 mm-5 h group (744.1 ± 61.2 MPa), which was attributed to phase-transformation toughening. The lowest values were observed in the case of the 5 Y-PSZ-1.5 mm-5 h (338.3 ± 34.8 MPa) group. CONCLUSIONS: Both material type and thickness significantly affect the flexural strength of zirconia ceramics, whereas aging time does not; thus, material selection and thickness are crucial considerations for clinicians.
Assuntos
Cerâmica , Resistência à Flexão , Teste de Materiais , Microscopia Eletrônica de Varredura , Difração de Raios X , Ítrio , Zircônio , Zircônio/química , Cerâmica/química , Ítrio/química , Fatores de Tempo , Propriedades de Superfície , Análise do Estresse Dentário , Materiais Dentários/químicaRESUMO
Beta-tricalcium phosphate (ß-TCP) scaffolds manufactured through the foam replication method are widely employed in bone tissue regeneration. The mechanical strength of these scaffolds is a significant challenge, partly due to the rheological properties of the original suspension. Various strategies have been explored to enhance the mechanical properties. In this research, ß-TCP scaffolds containing varying concentrations (0.25-1.00 wt%) of multi-walled carbon nanotubes (MWCNT) were developed. The findings indicate that the addition of MWCNTs led to a concentration-dependent improvement in the viscosity of ß-TCP suspensions. All the prepared slurries exhibited viscoelastic behavior, with the storage modulus surpassing the loss modulus. The three time interval tests revealed that MWCNT-incorporated ß-TCP suspensions exhibited faster structural recovery compared to pure ß-TCP slurries. Introducing MWCNT modified compressive strength, and the optimal improvement was obtained using 0.75 wt% MWCNT. The in vitro degradation of ß-TCP was also reduced by incorporating MWCNT. While the inclusion of carbon nanotubes had a marginal negative impact on the viability and attachment of MC3T3-E1 cells, the number of viable cells remained above 70% of the control group. Additionally, the results demonstrated that the scaffold increased the expression level of osteocalcin, osteoponthin, and alkaline phosphatase genes of adiposed-derived stem cells; however, higher levels of gene expersion were obtained by using MWCNT. The suitability of MWCNT-modified ß-TCP suspensions for the foam replication method can be assessed by evaluating their rheological behavior, aiding in determining the critical additive concentration necessary for a successful coating process.
Assuntos
Fosfatos de Cálcio , Nanotubos de Carbono , Engenharia Tecidual , Alicerces Teciduais , Fosfatos de Cálcio/química , Nanotubos de Carbono/química , Alicerces Teciduais/química , Engenharia Tecidual/métodos , Animais , Camundongos , Linhagem Celular , Osso e Ossos/metabolismo , Sobrevivência Celular/efeitos dos fármacos , Teste de Materiais , Regeneração Óssea/efeitos dos fármacos , Osteoblastos/metabolismo , Osteoblastos/efeitos dos fármacos , Osteoblastos/citologia , ViscosidadeRESUMO
This study reports on the modification of bacterial cellulose (BC) membranes produced by static fermentation of Komagataeibacter xylinus bacterial strains with graphene oxide-silver nanoparticles (GO-Ag) to yield skin wound dressings with improved antibacterial properties. The GO-Ag sheets were synthesized through chemical reduction with sodium citrate and were utilized to functionalize the BC membranes (BC/GO-Ag). The BC/GO-Ag composites were characterized to determine their surface charge, morphology, exudate absorption, antimicrobial activity, and cytotoxicity by using fibroblast cells. The antimicrobial activity of the wound dressings was assessed against Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa. The results indicate that the BC/GO-Ag dressings can inhibit â¼70% of E. coli cells. Our findings also revealed that the porous BC/GO-Ag antimicrobial dressings can efficiently retain 94% of exudate absorption after exposure to simulated body fluid (SBF) for 24 h. These results suggest that the dressings could absorb excess exudate from the wound during clinical application, maintaining adequate moisture, and promoting the proliferation of epithelial cells. The BC/GO-Ag hybrid materials exhibited excellent mechanical flexibility and low cytotoxicity to fibroblast cells, making excellent wound dressings able to control bacterial infectious processes and promote the fast healing of dermal lesions.
Assuntos
Antibacterianos , Materiais Biocompatíveis , Celulose , Escherichia coli , Grafite , Teste de Materiais , Nanopartículas Metálicas , Testes de Sensibilidade Microbiana , Prata , Staphylococcus aureus , Cicatrização , Grafite/química , Grafite/farmacologia , Prata/química , Prata/farmacologia , Cicatrização/efeitos dos fármacos , Celulose/química , Celulose/farmacologia , Nanopartículas Metálicas/química , Antibacterianos/química , Antibacterianos/farmacologia , Staphylococcus aureus/efeitos dos fármacos , Escherichia coli/efeitos dos fármacos , Materiais Biocompatíveis/química , Materiais Biocompatíveis/farmacologia , Tamanho da Partícula , Pseudomonas aeruginosa/efeitos dos fármacos , Gluconacetobacter xylinus/química , Humanos , Camundongos , Bandagens , AnimaisRESUMO
OBJECTIVES: To evaluate the marginal integrity (MI%) and to characterize specific properties of a thermoviscous bulk-fill resin composite, two regular bulk-fill resin composites, and a non-bulk-fill resin composite. MATERIALS AND METHODS: VisCalor bulk (VBF), Filtek One Bulk Fill (OBF), and Aura Bulk Fill (ABF) were evaluated. Filtek Z250 XT (ZXT) was used as non-bulk-fill control. MI% was evaluated in standardized cylindrical cavities restored with the composites by using a 3D laser confocal microscope. The following properties were characterized: volumetric polymerization shrinkage (VS%), polymerization shrinkage stress (Pss), degree of conversion (DC%), microhardness (KHN), flexural strength (FS), and elastic modulus (EM). Data were analyzed by one-way and two-way ANOVA, and Tukey HSD post-hoc test (α = 0.05). RESULTS: VBF presented the highest MI% and the lowest VS% and Pss (p < 0.05). DC% ranged from 59.4% (OBF) to 71.0% (ZXT). ZXT and VBF presented similar and highest KHN than OBF and ABF (p < 0.05). ABF presented the lowest FS (p < 0.05). EM ranged from 5.5 GPa to 7.7 GPa, with the values of ZXT and VBF being similar and statistically higher than those of OBF and ABF (p < 0.05). CONCLUSIONS: Thermoviscous technology employed by VisCalor bulk was able to improve its mechanical behavior comparatively to regular bulk-fill resin composites and to contribute to a better marginal integrity in restorations built up in cylindrical cavities with similar geometry to a class I cavity as well. Although presenting overall better physicomechanical properties, Z250 XT presented the worst MI%. CLINICAL RELEVANCE: The marginal integrity, which is pivotal for the success of resin composite restorations, could be improved using VisCalor bulk-fill. The worst MI% presented by Z250 XT reinforces that non-bulk-fill resin composites shall not be bulk-inserted in the cavity to be restored.
Assuntos
Resinas Compostas , Adaptação Marginal Dentária , Módulo de Elasticidade , Resistência à Flexão , Teste de Materiais , Polimerização , Propriedades de Superfície , Resinas Compostas/química , Dureza , Microscopia Confocal , Técnicas In Vitro , Restauração Dentária Permanente/métodos , Análise do Estresse DentárioRESUMO
Because nickel-titanium (NiTi) alloys have unique functions, such as superelasticity, shape memory, and hysteresis similar to bone in the loading-unloading cycles of their recoverable deformations. They likely offer good bone integration, a low loosening rate, individual customization, and ease of insertion. Due to the poor processability of NITI, traditional methods cannot manufacture NiTi products with complex shapes. Orthopedic NiTi implants need to show an adequate fracture elongation of at least 8%. Additive manufacturing can be used to prepare NiTi implants with complex structures and tunable porosity. However, as previously reported, additively manufactured NiTi alloys could only exhibit a maximum tensile fracture strain of 7%. In new reports, a selective laser melting (SLM)-NiTi alloy has shown greater tensile strain (15.6%). Nevertheless, due to the unique microstructure of additive manufacturing NiTi that differs from traditional NITI, the biocompatibility of SLM-NITI manufactured by this new process requires further evaluation In this study, the effects of the improved NiTi alloy on bone marrow mesenchymal stem cell (BMSC) proliferation, adhesion, and cell viability were investigated via in vitro studies. A commercial Ti-6Al-4V alloy was studied side-by-side for comparison. Like the Ti-6Al-4V alloy, the SLM-NiTi alloy exhibited low cytotoxicity toward BMSCs and similar effect on cell adhesion or cell viability. This study demonstrates that the new SLM-NiTi alloy, which has exhibited improved mechanical properties, also displays excellent biocompatibility. Therefore, this alloy may be a superior implant material in biomedical implantation.
Assuntos
Ligas , Materiais Biocompatíveis , Adesão Celular , Proliferação de Células , Sobrevivência Celular , Teste de Materiais , Células-Tronco Mesenquimais , Níquel , Resistência à Tração , Titânio , Titânio/química , Materiais Biocompatíveis/química , Ligas/química , Células-Tronco Mesenquimais/efeitos dos fármacos , Células-Tronco Mesenquimais/citologia , Níquel/química , Sobrevivência Celular/efeitos dos fármacos , Adesão Celular/efeitos dos fármacos , Proliferação de Células/efeitos dos fármacos , Animais , Lasers , Próteses e Implantes , Estresse Mecânico , Propriedades de SuperfícieRESUMO
OBJECTIVES: To synthesize casein enzymatic hydrolysate (CEH)-laden gelatin methacryloyl (GelMA) fibrous scaffolds and evaluate the cytocompatibility and anti-inflammatory effects on dental pulp stem cells (DPSCs). MATERIALS AND METHODS: GelMA fibrous scaffolds with 10%, 20%, and 30% CEH (w/w) and without CEH (control) were obtained via electrospinning. Chemo-morphological, degradation, and mechanical analyses were conducted to evaluate the morphology and composition of the fibers, mass loss, and mechanical properties, respectively. Adhesion/spreading and viability of DPSCs seeded on the scaffolds were also assessed. The anti-inflammatory potential on DPSCs was tested after the chronic challenge of cells with lipopolysaccharides (LPS), followed by treatment with extracts obtained after immersing the scaffolds in α-MEM. The synthesis of the pro-inflammatory cytokines IL-6, IL-1α, and TNF-α was measured by ELISA. Data were analyzed by ANOVA/post-hoc tests (α = 5%). RESULTS: CEH-laden electrospun fibers had a larger diameter than pure GelMA (p ≤ 0.036). GelMA scaffolds laden with 20% and 30% CEH had a greater mass loss. Tensile strength was reduced for the 10% CEH fibers (p = 0.0052), whereas no difference was observed for the 20% and 30% fibers (p ≥ 0.6736) compared to the control. Young's modulus decreased with CEH (p < 0.0001). Elongation at break increased for the 20% and 30% CEH scaffolds (p ≤ 0.0038). Over time, DPSCs viability increased across all groups, indicating cytocompatibility, with CEH-laden scaffolds exhibiting greater cell viability after seven days (p ≤ 0.0166). Also, 10% CEH-GelMA scaffolds decreased the IL-6, IL-1α, and TNF-α synthesis (p ≤ 0.035). CONCLUSION: CEH-laden GelMA scaffolds facilitated both adhesion and proliferation of DPSCs, and 10% CEH provided anti-inflammatory potential after chronic LPS challenge. CLINICAL RELEVANCE: CEH incorporated in GelMA fibrous scaffolds demonstrated the potential to be used as a cytocompatible and anti-inflammatory biomaterial for vital pulp therapy.
Assuntos
Anti-Inflamatórios , Caseínas , Sobrevivência Celular , Polpa Dentária , Gelatina , Alicerces Teciduais , Gelatina/química , Polpa Dentária/citologia , Polpa Dentária/efeitos dos fármacos , Alicerces Teciduais/química , Humanos , Anti-Inflamatórios/farmacologia , Sobrevivência Celular/efeitos dos fármacos , Metacrilatos/química , Teste de Materiais , Ensaio de Imunoadsorção Enzimática , Resistência à Tração , Células Cultivadas , Células-Tronco/efeitos dos fármacos , Adesão Celular/efeitos dos fármacos , Materiais Biocompatíveis/farmacologia , Materiais Biocompatíveis/química , Citocinas/metabolismo , Propriedades de SuperfícieRESUMO
Orthodontic adhesive doped with sulfur-modified TiO2 promotes antibacterial effect. The objective of the study was to characterize the physical, mechanical and antibacterial properties of the orthodontic bracket adhesive, doped with modified titanium dioxide nanoparticles. Sulfur-doped TiO2 was synthetized and morphological topography was analyzed with TEM and SEM imaging. The catalytic performance during the degradation of rhodamine B was assessed. Nanomaterial was added at four concentration (1, 3, 6, and 10 wt%) to a commercial orthodontic adhesive. The shear bond strength and microhardness of a resin-based orthodontic adhesive containing S-TiO2 were evaluated. The inhibitory effect of the pure and doped adhesives against Escherichia coli and Streptococcus mutans was examined. As the results, the highest antimicrobial activity and good adhesive properties were noticed for light-cured orthodontic adhesive doped with 3% of S-TiO2. In this case, orthodontic adhesives with strong and long-lasting bactericidal properties can be created through the incorporation of modified TiO2 without negatively influencing microhardnesses, and bonding ability. White spot lesion and demineralization, which occurs very often in patients during orthodontic treatment, can be therefore minimized.
Assuntos
Antibacterianos , Cimentos Dentários , Escherichia coli , Streptococcus mutans , Titânio , Titânio/química , Titânio/farmacologia , Antibacterianos/farmacologia , Antibacterianos/química , Streptococcus mutans/efeitos dos fármacos , Escherichia coli/efeitos dos fármacos , Cimentos Dentários/química , Cimentos Dentários/farmacologia , Teste de Materiais , Resistência ao Cisalhamento , Braquetes Ortodônticos , Humanos , Enxofre/químicaRESUMO
Dental materials are challenged by wear processes in the oral environment and should be evaluated in laboratory tests prior to clinical use. Many laboratory wear-testing devices are high-cost investments and not available for cross-centre comparisons. The 'Rub&Roll' wear machine enables controlled application of force, chemical and mechanical loading, but the initial design was not able to test against rigid antagonist materials. The current study aimed to probe the sensitivity of a new 'Rub&Roll' set-up by evaluating the effect of force and test solution parameters (deionized water; water + abrasive medium; acid + abrasive medium) on the wear behaviour of direct and indirect dental resin-based composites (RBCs) compared with human molars against 3D-printed rod antagonists. Molars exhibited greater height loss than RBCs in all test groups, with the largest differences recorded with acidic solutions. Direct RBCs showed significantly greater wear than indirect RBCs in the groups containing abrasive media. The acidic + abrasive medium did not result in increased wear of RBC materials. The developed method using the 'Rub&Roll' wear machine in the current investigation has provided a sensitive wear test method to allow initial screening of resin-based composite materials compared with extracted human molars under the influence of different mechanical and erosive challenges.
Assuntos
Resinas Compostas , Materiais Dentários , Teste de Materiais , Humanos , Teste de Materiais/métodos , Resinas Compostas/química , Dente Molar , Propriedades de SuperfícieRESUMO
PURPOSE: This in vitro study aimed to create a graded structured dental crown using 3D printing technology and investigate the fracture resistance and the adaptation of this new design. MATERIALS AND METHODS: A dental crown with a uniform thickness of 1.5 mm was designed, and the exported stereolithography file (STL) was used to manufacture 30 crowns in three groups (n = 10), solid (SC), bilayer (BL), and multilayer (ML) crowns using 3D jet printing technology. Marginal and internal gaps were measured using the silicone replica technique. Crowns were then luted to a resin die using a temporary luting agent and the fracture resistance was measured using a universal testing machine. One-way ANOVA and Tukey post hoc tests were used to compare the fracture resistance and the adaptation of crowns at a significance level of 0.05. RESULTS: Mean marginal and internal gap of the ML group were 80 and 82 mm, respectively; which were significantly (p < 0.05) smaller than BL (203 and 183 mm) and SC (318 and 221 mm) groups. The SC group showed the highest mean load at fracture (2330 N) which was significantly (p < 0.05) higher than the BL (1716 N) and ML (1516 N) groups. CONCLUSION: 3D jet printing technology provides an opportunity to manufacture crowns in a graded structure with various mechanical properties. This study provided an example of graded structured crowns and presented their fracture resistance. SC group had the highest fracture resistance; however, ML had the best marginal and internal adaptation.