Your browser doesn't support javascript.
loading
Paper-based microfluidic colorimetric sensor on a 3D printed support for quantitative detection of nitrite in aquatic environments.
Rajasulochana, P; Ganesan, Yaswanth; Kumar, P Senthil; Mahalaxmi, S; Tasneem, Fahira; Ponnuchamy, Muthamilselvi; Kapoor, Ashish.
Afiliação
  • Rajasulochana P; Department of Genetic Engineering, Bharath Institute of Science and Technology, Chennai, Tamil Nadu, 600073, India.
  • Ganesan Y; Department of Chemical Engineering, SRM Institute of Science and Technology, Kattankulathur, Tamil Nadu, 603203, India.
  • Kumar PS; Department of Chemical Engineering, Sri Sivasubramaniya Nadar College of Engineering, Chennai, 603110, India; Centre of Excellence in Water Research (CEWAR), Sri Sivasubramaniya Nadar College of Engineering, Chennai, 603110, India. Electronic address: senthilkumarp@ssn.edu.in.
  • Mahalaxmi S; Department of Chemical Engineering, Sri Sivasubramaniya Nadar College of Engineering, Chennai, 603110, India; Centre of Excellence in Water Research (CEWAR), Sri Sivasubramaniya Nadar College of Engineering, Chennai, 603110, India.
  • Tasneem F; Department of Genetic Engineering, Bharath Institute of Science and Technology, Chennai, Tamil Nadu, 600073, India.
  • Ponnuchamy M; Department of Chemical Engineering, SRM Institute of Science and Technology, Kattankulathur, Tamil Nadu, 603203, India.
  • Kapoor A; Department of Chemical Engineering, SRM Institute of Science and Technology, Kattankulathur, Tamil Nadu, 603203, India. Electronic address: ashishko@srmist.edu.in.
Environ Res ; 208: 112745, 2022 05 15.
Article em En | MEDLINE | ID: mdl-35051426
ABSTRACT
To ensure safe drinking water, it is necessary to have a simple method by which the probable pollutants are detected at the point of distribution. Nitrite contamination in water near agricultural locations could be an environmental concern due to its deleterious effects on the human population. The development of a frugal paper-based microfluidic sensor could be desirable to achieve the societal objective of providing safe drinking water. This work describes the development of a facile and cost-effective microfluidic paper-based sensor for quantitative estimation of nitrite in aquatic environments. A simple punching machine was used for fabrication and rapid prototyping of paper-based sensors without the need of any specialized equipment or patterning techniques. A reusable 3D printed platform served as the support for simultaneous testing of multiple samples. The nitrite estimation was carried out with smartphone-assisted digital image acquisition and colorimetric analysis. Under optimized experimental conditions, the variation in average grayscale intensity with concentration of nitrite was linear in the range from 0.1 to 10 ppm. The limits of detection and quantitation were 0.12 ppm and 0.35 ppm respectively. The reproducibility, expressed as relative standard deviation was 1.31%. The selectivity of nitrite detection method was determined by performing interference studies with commonly existing co-ions in water, such as bicarbonates, chloride and sulphate. The paper-based sensor was successfully applied for estimation of nitrite in actual water samples and showed high recoveries in the range of 83.5-109%. The results were in good agreement with those obtained using spectrophotometry. The developed paper-based sensor method, by virtue of its simplicity, ease of fabrication and use, could be readily extended for detection of multiple analytes in resource-limited settings.
Assuntos
Palavras-chave

Texto completo: 1 Base de dados: MEDLINE Assunto principal: Água Potável / Nitritos Idioma: En Ano de publicação: 2022 Tipo de documento: Article

Texto completo: 1 Base de dados: MEDLINE Assunto principal: Água Potável / Nitritos Idioma: En Ano de publicação: 2022 Tipo de documento: Article