ABSTRACT
The functional support and advancement of our body while preserving inherent naturalness is one of the ultimate goals of bioengineering. Skin protection against infectious pathogens is an application that requires common and long-term wear without discomfort or distortion of the skin functions. However, no antimicrobial method has been introduced to prevent cross-infection while preserving intrinsic skin conditions. Here, we propose an antimicrobial skin protection platform copper nanomesh, which prevents cross-infectionmorphology, temperature change rate, and skin humidity. Copper nanomesh exhibited an inactivation rate of 99.99% for Escherichia coli bacteria and influenza virus A within 1 and 10 min, respectively. The thin and porous nanomesh allows for conformal coating on the fingertips, without significant interference with the rate of skin temperature change and humidity. Efficient cross-infection prevention and thermal transfer of copper nanomesh were demonstrated using direct on-hand experiments.
Subject(s)
Anti-Infective Agents , Copper , Cross Infection , Metal Nanoparticles , Skin , Anti-Infective Agents/pharmacology , Copper/pharmacology , Cross Infection/prevention & control , Escherichia coli/drug effects , Fingers , Humans , Influenza A virus/drug effects , Porosity , Skin/microbiologyABSTRACT
Control of the spatial distribution of various cell types is required to construct functional tissues. Here, we report a simple topographical structure changed the spatial cell density. A concave curved boundary was designed, which allowed the spatial descent moving of cells and the change in spatial distributions of co-cultured cells. We utilized the difference in cell motility between myoblast cells (C2C12) and neuronal cells (PC12) to demonstrate the feasibility of spontaneous change in spatial cell density. Without the curved boundaries, high motility cells (C2C12) did not migrate to the adjacent area, which resulted in a slight temporal change (< 15%) in the spatial cell distribution. In contrast, with the curved boundaries, the cell density of the high motility cells in the groove to those cells on the ridge showed an increase exceeding 45%. On the other hand, the temporal change in the spatial cell distribution of low motility cells (PC12) was below 15% with or without the curved boundaries. In addition, as groove width increased, both cells displayed more initially gathering in groove. Importantly, these cell-type dependent results were also maintained under co-culture conditions. Our results suggest that designing topographical interfaces changes spatial cell density without any manipulation and is useful for multi-cellular constructs.
Subject(s)
Cell Engineering/methods , Cell Movement , Animals , Cell Count , Coculture Techniques , Mice , Myoblasts/cytology , Neurons/cytology , PC12 Cells , RatsABSTRACT
Flexible sensors enable on-skin and in-body health monitoring, which require flexible thermal protection circuits to prevent overheating and operate the devices safely. Here, ultrathin fiber-mesh polymer positive temperature coefficient (PTC) thermistors via electrospinning are developed. The fiber-type thermistors are composed of acrylate polymer and carbon nanofibers. The fibrous composite materials are coated with a parylene to form a core-sheath structure, which improves the repeatability of temperature characteristics. Approximately 5 µm thick fiber-type thermistors exhibit an increase in the resistance by three orders of magnitude within ≈2 °C and repeatable temperature characteristics for up to 400 cycles. The mesh structure enables the thermistor layer to be ultra-lightweight and transparent; the mesh-type thermistor operates with a fiber density of 16.5 µg cm-2 , whose fiber layer has a transmittance of more than 90% in the 400-800 nm region. By fabricating the mesh thermistor on a 1.4 µm thick substrate, the thermistor operates without degradation when wrapped around a 280 µm radius needle. Furthermore, the gas-permeable property is demonstrated by fabricating the fibrous thermistor on a mesh substrate. The proposed ultrathin mesh polymer PTC thermistors form the basis for on-skin and implantable devices that are equipped with overheat prevention.
Subject(s)
Polymers , Surgical Mesh , Temperature , Polymers/chemistry , Acrylates , CarbonABSTRACT
Placing cells in the proper position is important for tissue engineering. Previous works addressed this subject in the way of controlling cell migration by micro- or nano-patterning the substrates. However, the problem of changing spatial cell density freely under co-culture conditions is remaining. To solve this problem, in this work, we report that C2C12 spatial cell density changes by the patterning geometric boundary of the topographical structures. In 48 h after seeding cells, at the linear boundary (ridge-groove) structures, C2C12 Groove/Ridge ratio was under 0.70 both under monoculture conditions and under co-culture conditions. In contrast, at the combining the linear boundary and the round boundary (ridge-groove + hole) structures, the ratio was over 0.89 under both culture conditions. This our finding will provide a new device which enables to manipulate spatial cell density under co-culture conditions for heterogeneous tissue engineering.