Recycling of deep eutectic solvent in the extraction of ferulic acid from oil palm empty fruit bunch.

The study explored ferulic acid extraction from palm empty fruit bunch (EFB) fiber using deep eutectic solvent (DES) of chlorine chloride-acetic acid as the extraction medium and the way to recover and recycle the DES thereafter. Antisolvent was added to selectively precipitate the ferulic acid, which was recovered by filtration thereafter. Recycling the DES without further purification led to increased ferulic acid yield with each subsequent extraction, likely due to retained ferulic acid. The retained ferulic acid and other impurities could be removed by precipitation brought upon by the addition of a second antisolvent. 1H nuclear magnetic resonance revealed that there was no excess ferulic acid in the recycled DES-treated with two types of antisolvents (ethanol and water). The yield of ferulic acid increased from 0.1367-0.1856 g/g when treated with only one antisolvent to 0.1368-0.2897 g/g with two antisolvent treatments. Oil droplets were also observed in the DES upon the addition of antisolvent 2, with recovered oil ranging from 0.6% to 3%. The study emphasized the significance of using DES as an extraction medium for ferulic acid from oil palm EFB fiber and the method to recycle the DES for subsequent processes.

Facile Preparation and Analytical Utility of ZnO/Date Palm Fiber Nanocomposites in Lead Removal from Environmental Water Samples.

This study reports a facile approach for preparing low-cost, eco-friendly nanocomposites of ZnO nanoparticles (NPs) and date palm tree fiber (DPF) as a biomass sorbent. The hypothesis of this research work is the formation of an outstanding adsorbent based on the date palm fiber and ZnO nanoparticles. ZnO NP/DPF nanocomposites were synthesized by mixing the synthesized ZnO NPs and DPF in different mass ratios and evaluating their efficacy in adsorbing Pb2+ from aqueous solutions. The structure and surface morphology of the developed ZnO NP/DPF nanocomposite were critically characterized by XRD, FESEM, and TEM techniques. Compared to ZnO NPs, the ZnO NP/DPF nanocomposites displayed significantly enhanced Pb2+ uptake. Pb2+ adsorption was confirmed via various isotherm and kinetic models and thermodynamics. The computed Langmuir sorption capacity (qm) was found to be 88.76 mg/g (R2 > 0.998), and the pseudo-second-order R2 > 0.999 model was most appropriate for describing Pb2+ adsorption. Impregnating the biomass with ZnO NPs enhanced the spontaneity of the process, and the value (−56.55 kJ/mol) of ΔH displayed the exothermic characteristics of Pb2+ retention. Only the loaded ZnO NP/DPF achieved the removal of a high percentage (84.92%) of Pb2+ from the environmental water sample (seawater). This finding suggests the use of ZnO NP/DPF nanocomposites for removing heavy metals from environmental water samples to purify the samples.

Design for preparation of more active cross-linked enzyme aggregates of Burkholderia cepacia lipase using palm fiber residue.

A new design of cross-linked enzyme aggregates (CLEAs) of Burkholderia cepacia lipase (BCL) based mainly on the use of lignocellulosic residue of palm fiber as an additive was proposed. Different parameters for the preparation of active CLEAs in the hydrolysis of olive oil, such as precipitation agents, crosslinking agent concentration, additives, and coating agents were investigated. The highest activity yield (121.1 ± 0.1%) and volumetric activity (1578.1 ± 2.5 U/mL) were achieved for CLEAs prepared using the combination of a coating step with Triton® X-100 and polyethyleneimine plus the use of palm fiber as an additive. The variations of the secondary structures of BCL-CLEAs were analyzed by second-derivative infrared spectra, mainly indicating a reduction of the α-helix structure, which was responsible for the lipase activation in the supramolecular structure of the CLEAs. Thus, these results provided evidence of an innovative design of BCL-CLEAs as a sustainable and biocompatible opportunity for biotechnology applications.

Oil palm fiber biodegradation: physico-chemical and structural relationships.

MAIN CONCLUSION: X-ray microtomography results revealed that delignification process damaged the oil palm fibers, which correlated well with reduction of lignin components and increase of the phenolic content. Biodegradation investigation of natural fibers normally focuses on physico-chemical analysis, with less emphasis on physical aspect like fiber structures affect from microbial activity. In this work, the performance of Pycnoporus sanguineus to delignify oil palm empty fruit bunch fibers through solid-state fermentation utilizing various ratio of POME sludge was reported. In addition to tensile testing, physico-chemical and X-ray microtomography (µ-CT) analyses on the oil palm fibers were conducted to determine the effectiveness of the degradation process. The best ratio of fiber to fungi (60:40) was chosen based on the highest lignin loss and total phenolic content values and further investigation was performed to obtain fermentation kinetics data of both laccase and manganese peroxidase. µ-CT results revealed that delignification process damaged the pre-treated and untreated fibers structure, as evident from volume reduction after degradation process. This is correlated with reduction of lignin component and increase of the phenolic content, as well as lower stress-strain curves of the pre-treated fibers compared to the untreated ones (from tensile testing). It is suggested that P. sanguineus preferred to consume the outer layer of the fiber, before it penetrates through the cellular structure of the inner fiber.

Innovative ionic liquid pretreatment followed by wet disk milling treatment provides enhanced properties of sugar palm nano-fibrillated cellulose.

In order to accommodate the increased demand for innovative materials, intensive research has focused on natural resources. In pursuit of advanced substances that exhibit functionality, sustainability, recyclability, and cost-effectiveness, the present work attempted an alternative study on cellulose nanofibers derived from sugar palm fiber. Leveraging an innovative approach involving ionic liquid (IL) pre-treatment, bleaching, and wet disc mill technique, nano-fibrillated cellulose (NFC) was successfully obtained from the sugar palm fiber source. Remarkably, 96.89% of nanofibers were extracted from the sugar palm fiber, demonstrating the process's efficacy and scalability. Further investigation revealed that the sugar palm nano-fibrillated cellulose (SPNFC) exhibited a surface area of 3.46 m2/g, indicating a significant interface for enhanced functionality. Additionally, the analysis unveiled an average pore size of 4.47 nm, affirming its suitability for various applications that necessitate precise filtration. Moreover, the surface charge densities of SPNFC were found to be -32.1 mV, offering opportunities for surface modification and enhanced interactions with various materials. The SPNFC exhibit remarkable thermal stability, enduring temperatures of up to 360.5 °C. Additionally, the isolation process is evident in a significant rise in the crystallinity index, escalating from 50.97% in raw fibers to 61.62% in SPNFC. These findings shed light on the vast potential and distinct features of SPNFC, opening the path for its application in a wide array of industries, including but not limited to advanced materials, biomedicine, and environmental engineering.

Modification of palm fiber with chitosan-AESO blend coating.

Natural fibers are available as an essential substitute for synthetic fiber in many applications. However, the sensitivity of Chinese Windmill Palm or Trachycarpus Fortune Fiber (TFF) to water causes low interfacial bonding between the matrix and the fiber and at the end reduces the mechanical properties of the composite product. Alkaline treatment improves mechanical properties and does not affect water absorption. Hence, additional treatment in the coating is required. This study uses alkaline treatment and coating modification using blended chitosan and Acrylated Epoxidized Soybean Oil (AESO). Blend coating between AESO and chitosan is performed to increase water absorption and mechanical properties. TFF water resistance improved significantly after the coating, with water absorption of the alkaline/blend coating-TFF of 3.98 % ± 0.52 and swell ability of 3.156 % ± 0.17. This indicated that blend coating had formed a cross-link of fiber and matrix after alkalization. Thus, the single fiber tensile strength increased due to the alkaline treatment, and water absorption decreased due to the coating. The combination of alkaline treatment and blend coating on TFF brings excellent properties, as shown by the increase in tensile strength in both single fiber test and composite.

Preparation, Characterization, and Chemically Modified Date Palm Fiber Waste Biomass for Enhanced Phenol Removal from an Aqueous Environment.

The date palm tree is extensively cultivated in Middle Eastern countries such as Saudi Arabia, generating a large amount of waste in the form of leaves, seeds, and fibrous materials. This study examined the feasibility of using raw date palm fiber (RDPF) and NaOH chemically modified date palm fiber (NaOH-CMDPF) obtained from discarded agricultural waste for the removal of phenol in an aqueous environment. The adsorbent characterization was performed by using different techniques, i.e., particle size analysis; elemental analyzer (CHN); and BET, FTIR, and FESEM-EDX analysis. The FTIR analysis revealed the presence of various functional groups on the surface of the RDPF and NaOH-CMDPF. The results showed that chemical modification by NaOH increased the phenol adsorption capacity that was well-fitted by the Langmuir isotherm. Higher removal was obtained with NaOH-CMDPF (86%) than with the RDPF (81%). The RDPF and NaOH-CMDPF sorbents' maximum (Qm) adsorption capacities were more than 45.62 mg/g and 89.67 mg/g and were comparable to the sorption capacities of various other types of agricultural waste biomass reported in the literature. The kinetic studies confirmed that the adsorption of phenol followed the pseudo-second-order kinetic process. The present study concluded that the RDPF and NaOH-CMDPF were eco-friendly and cost-effective in promoting sustainable management and the reuse of the Kingdom's lignocellulosic fiber waste material.

Cracking and erosion behaviors of sand-clay mixtures stabilized with microbial biopolymer and palm fiber.

Drying-induced cracks and precipitation-induced erosion negatively impact the performance of soils in the context of extreme weather events. This study introduces two effective and sustainable materials, microbial biopolymer (MB) and palm fibers (PF), for cracking and erosion control in the sand-clay mixtures. A series of desiccation cracking tests, erosion tests, and SEM tests were conducted to evaluate the effectiveness of the treatment. The results showed that MB could significantly improve the resistance of the soil to cracking and scouring, and the improvement increased with increasing MB content. The optimum MB content was 0.15 % to achieve the maximum cracking and erosion resistance. For samples with varying sand contents, 0.15 % MB addition reduced the crack ratio, total crack length, and accumulative erosion ratio by 19.55 %-96.91 %, 4.22 %-99.58 %, and 57.88 %-89.53 %, respectively. In addition, PF positively affected the anti-crack and anti-erosion properties of the soil, and the application of 0.60 % PF had the best performance for both improvements. The cracks in the soils were mostly fine and shallow with the addition of 0.60 % PF, and therefore, the accumulative erosion ratio decreased by 44.18 %-62.76 % for samples with varying sand contents. Compared to the untreated soil, the degree of cracking and erosion was less due to the formation of a structure with more macropores and a sand skeleton in the treated samples with higher sand content. MB addition provides strong inter-particle bonding connections and a hydrophilic crust structure to improve the soils' resistance to cracking and erosion, while the fiber reinforcement effect benefits from interfacial friction and spatial restriction effects. This study provides mechanistic interpretations of desiccation cracking and erosion behavior in sand-clay mixtures under different treatments. It may guide the design of low-carbon technologies for geotechnical engineering applications.

Optimization and Modelling the Mechanical Performance of Date Palm Fiber-Reinforced Concrete Incorporating Powdered Activation Carbon Using Response Surface Methodology.

Date palm fiber (DPF) has been reported to have many advantages when used in concrete, however, its major disadvantage is that it causes a reduction in compressive strength. In this research, powdered activated carbon (PAC) was added to cement in the DPF-reinforced concrete (DPFRC) to lessen the loss in strength. PAC has not been properly utilized as an additive in fiber reinforced concrete even though it has been reported to enhance the properties of cementitious composites. Response surface methodology (RSM) has also been utilized for experimental design, model development, results analysis, and optimization. The variables were DPF and PAC as additions each at proportions of 0%, 1%, 2%, and 3% by weight of cement. Slump, fresh density, mechanical strengths, and water absorption were the responses that were considered. From the results, both DPF and PAC decreased the workability of the concrete. DPF addition improved the splitting tensile and flexural strengths and reduced the compressive strength, and up to 2 wt% PAC addition enhanced the concrete's strength and lowered the water absorption. The proposed models using RSM were extremely significant and have excellent predictive power for the concrete's aforementioned properties. Each of the models was further validated experimentally and was found to have an average error of less than 5.5%. According to the results of the optimization, the optimal mix of 0.93 wt% DPF and 0.37 wt% PAC as cement additives resulted in the best properties of the DPFRC in terms of workability, strength, and water absorption. The optimization's outcome received a 91% desirability rating. The addition of 1% PAC increased the 28-day compressive strength of the DPFRC containing 0%, 1% and 2% DPF by 9.67%, 11.13% and 5.5% respectively. Similarly, 1% PAC addition enhanced the 28-day split tensile strength of the DPFRC containing 0%, 1% and 2% by 8.54%, 11.08% and 19.3% respectively. Likewise, the 28-day flexural strength of DPFRC containing 0%, 1%, 2% and 3% improved by 8.3%, 11.15%, 18.7% and 6.73% respectively with the addition of 1% PAC. Lastly, 1% PAC addition led to a reduction in the water absorption of DPFRC containing 0% and 1% DPF by 17.93% and 12.2% respectively.

Application of Taguchi Method to Optimize the Parameter of Fused Deposition Modeling (FDM) Using Oil Palm Fiber Reinforced Thermoplastic Composites.

Fused Deposition Modeling (FDM) is capable of producing complicated geometries and a variety of thermoplastic or composite products. Thus, it is critical to carry out the relationship between the process parameters, the finished part's quality, and the part's mechanical performance. In this study, the optimum printing parameters of FDM using oil palm fiber reinforced thermoplastic composites were investigated. The layer thickness, orientation, infill density, and printing speed were selected as optimization parameters. The mechanical properties of printed specimens were examined using tensile and flexural tests. The experiments were designed using a Taguchi experimental design using a L9 orthogonal array with four factors, and three levels. Analysis of variance (ANOVA) was used to determine the significant parameter or factor that influences the responses, including tensile strength, Young's modulus, and flexural strength. The fractured surface of printed parts was investigate using scanning electron microscopy (SEM). The results show the tensile strength of the printed specimens ranged from 0.95 to 35.38 MPa, the Young's modulus from 0.11 to 1.88 GPa, and the flexural strength from 2.50 to 31.98 MPa. In addition, build orientation had the largest influence on tensile strength, Young's modulus, and flexural strength. The optimum printing parameter for FDM using oil palm fiber composite was 0.4 mm layer thickness, flat (0 degree) of orientation, 50% infill density, and 10 mm/s printing speed. The results of SEM images demonstrate that the number of voids seems to be much bigger when the layer thickness is increased, and the flat orientation has a considerable influence on the bead structure becoming tougher. In a nutshell, these findings will be a valuable 3D printing dataset for other researchers who utilize this material.

Evaluation of oil palm fiber biochar and activated biochar for sulphur dioxide adsorption.

The emission of sulphur dioxide (SO2) gas from power plants and factories to the atmosphere has been an environmental challenge globally. Thus, there is a great interest to control the SO2 gas emission economically and effectively. This study aims to use and convert abundantly available oil palm fiber (OPF) biomass into an adsorbent to adsorb SO2 gas. The preparation of OPF biochar and activated biochar was optimised using the Response Surface Methodology (RSM) based on selected parameters (i.e., pyrolysis temperature, heating rate, holding time, activation temperature, activation time and CO2 flowrate). The best adsorbent was found to be the OPF activated biochar (OPFAB) compared to OPF biochar. OPFAB prepared at 753 °C for 73 min of activation time with 497 ml/min of CO2 flow yields the best adsorption capacity (33.09 mg/g) of SO2. Meanwhile, OPF pyrolysed at 450 °C of heating temperature, 12 °C/min of heating rate and 98 min of holding time yield adsorption capacity at 18.62 mg/g. Various characterisations were performed to investigate the properties and mechanism of the SO2 adsorption process. Thermal regeneration shows the possibilities for the spent adsorbent to be recycled. The findings imply OPFAB as a promising adsorbent for SO2 adsorption.

Rapid Prediction of Mechanical Properties Based on the Chemical Components of Windmill Palm Fiber.

During spinning, the chemical component content of natural fibers has a great influence on the mechanical properties. How to rapidly and accurately measure these properties has become the focus of the industry. In this work, a grey model (GM) for rapid and accurate prediction of the mechanical properties of windmill palm fiber (WPF) was established to explore the effect of chemical component content on the Young's modulus. The chemical component content of cellulose, hemicellulose, and lignin in WPF was studied using near-infrared (NIR) spectroscopy, and an NIR prediction model was established, with the measured chemical values as the control. The value of RC and RCV were more than 0.9, while the values of RMSEC and RMSEP were less than 1, which reflected the excellent accuracy of the NIR model. External validation and a two-tailed t-test were used to evaluate the accuracy of the NIR model prediction results. The GM(1,4) model of WPF chemical components and the Young's modulus was established. The model indicated that the increase in cellulose and lignin content could promote the increase in the Young's modulus, while the increase in hemicellulose content inhibited it. The establishment of the two models provides a theoretical basis for evaluating whether WPF can be used in spinning, which is convenient for the selection of spinning fibers in practical application.

Evaluating the Influence of Elevated Temperature on Compressive Strength of Date-Palm-Fiber-Reinforced Concrete Using Response Surface Methodology.

Due to its availability and affordable processing, date palm fiber (DPF) is among the natural and sustainable fibers used in cementitious composites. Furthermore, DPF is an agricultural, organic, and fibrous material that when subjected to higher temperature can easily degrade and cause reduction in strength. Therefore, the influence of elevated temperatures on the unit weight and strengths of DPF-reinforced concrete needs to be examined. Under this investigation, DPF is used in proportions of 0-3% weight of binder to produce a DPF-reinforced concrete. Silica fume was utilized as a supplemental cementitious material (SCM) in various amounts of 0%, 5%, 10%, and 15% by weight to enhance the heat resistance of the DPF-reinforced concrete. The concrete was then heated to various elevated temperatures for an hour at 200 °C, 400 °C, 600 °C, and 800 °C. After being exposed to high temperatures, the weight loss and the compressive and relative strengths were examined. The weight loss of DPF-reinforced concrete escalated with increments in temperature and DPF content. The compressive and relative strengths of the concrete improved when heated up to 400 °C, irrespective of the DPF and silica fume contents. The heat resistance of the concrete was enhanced with the replacement of up to 10% cement with silica fume when heated to a temperature up to 400 °C, where there were enhancements in compressive and relative strengths. However, at 800 °C, silica fume caused a significant decline in strength. The developed models for predicting the weight loss and the compressive and relative strengths of the DPF-reinforced concrete under high temperature using RSM have a very high degree of correlation and predictability. The models were said to have an average error of less than 6% when validated experimentally. The optimum DPF-reinforced concrete mix under high temperature was achieved by adding 1% DPF by weight of binder materials, replacing 12.14% of the cement using silica fume, and subjecting the concrete to a temperature of 317 °C. The optimization result has a very high desirability of 91.3%.

Optimization of ethanol-extracted lignin from palm fiber by response surface methodology and preparation of activated carbon fiber for dehumidification.

Lignin is a renewable bioresource that can be used for a variety of value-added applications. However, the effective separation of lignin from lignocellulosic biomass remains an ongoing challenge. In this study, lignin was extracted from waste palm fiber and successfully converted into a dehumidifying material. The following four process parameters of lignin extraction from palm fiber were optimized systematically and comprehensively using the response surface methodology: reaction time, extraction temperature, ethanol concentration and solid/liquid ratio. The results revealed that under the optimum processing conditions (111 min of extraction at 174 °C using 73% ethanol at 1/16 g/mL solid/liquid ratio), the extraction yield of lignin was 56.2%. The recovery of ethanol solvent was as high as 91.8%. Further, the lignin could be directly used without purification to produce lignin-based activated carbon fibers (LACFs) with specific surface area and total pore volume of 1375 m2/g and 0.881 cm3/g, respectively. Compared with the commercial pitch-based activated carbon fiber, the LACF has a higher specific area and superior pore structure parameters. This work provides a feasible route for extracting lignin from natural palm fiber and demonstrates its use in the preparation of activated carbon fiber with a remarkable performance as a solid dehumidification agent.

Rheological and Morphological Properties of Oil Palm Fiber-Reinforced Thermoplastic Composites for Fused Deposition Modeling (FDM).

Fused deposition modelling (FDM) is a filament-based rapid prototyping technology that allows new composite materials to be introduced into the FDM process as long as they can be manufactured in feedstock filament form. The purpose of this research was to analyze the rheological behavior of oil palm fiber-reinforced acrylonitrile butadiene styrene (ABS) composites when used as a feedstock material, as well as to determine the best processing conditions for FDM. The composite's shear thinning behavior was observed, and scanning electron microscopy was used to reveal its composition. The morphological result found that there was a good fiber/matrix adhesion with a 3 wt% fiber loading, as no fiber pullouts or gaps developed between the oil palm fiber and ABS. However, some pores and fiber pullouts were found with a 5 and 7 wt% fiber loading. Next, the rheological results showed that the increment of fiber content (wt%) increased the viscosity. This discovery can definitely be used in the extrusion process for making wire filament for FDM. The shear thinning effect was increased by adding 3, 5, or 7 wt% of oil palm fiber. The non-Newtonian index (n) of the composites increased as the number of shear rates increased, indicating that the fiber loading had a significant impact on the rheological behavior. As the fiber loading increased, the viscosity and shear stress values increased as well. As a result, oil fiber reinforced polymer composites can be used as a feedstock filament for FDM.

Kinetics, isotherms, effect of structure, and computational analysis during the removal of three representative pharmaceuticals from water by adsorption using a biochar obtained from oil palm fiber.

Acetaminophen (ACE), cephalexin (CPX), and valsartan (VAL) are recognized water pollutants, which can be removed by adsorption. Herein, the removal of these pharmaceuticals using a biochar (BP), prepared from oil palm fiber, was tested. It was studied the structural effects of the pharmaceuticals and biochar on the adsorption process supported by experimental and computational results, plus characterizations of the material. The biochar has 76.05 m2 g-1 of surficial area, and carboxylic groups (1.343 mmol g-1) predominantly. The maximum adsorption uptakes were 7.3, 7.9, and 23.85 mg g-1 for ACE, CPX, and VAL, respectively; following pseudo-second-order kinetics. The best pollutants removal was obtained at acidic pH (3.0). Computational analyses indicated that oxygenated groups of BP (able to generate H-bond interactions) influenced the adsorption of pharmaceuticals. It can be remarked that BP is a low-cost adsorbent synthesized easily from wastes, with high feasibility to remove pharmaceutical structures from water.

Mechanical Properties of Sugar Palm (Arenga pinnata Wurmb. Merr)/Glass Fiber-Reinforced Poly(lactic acid) Hybrid Composites for Potential Use in Motorcycle Components.

This research aims to determine the mechanical properties of sugar palm fiber (Arenga pinnata Wurmb. Merr) (SPF)/glass fiber (GF)-reinforced poly(lactic acid) (PLA) hybrid composites for potential use in motorcycle components. The mechanical (hardness, compressive, impact, and creep) and flammability properties of SPF/GF/PLA hybrid composites were investigated and compared to commercially available motorcycle Acrylonitrile Butadiene Styrene (ABS) plastic components. The composites were initially prepared using a Brabender Plastograph, followed by a compression molding method. This study also illustrated the tensile and flexural stress-strain curves. The results revealed that alkaline-treated SPF/GF/PLA had the highest hardness and impact strength values of 88.6 HRS and 3.10 kJ/m2, respectively. According to the results, both alkaline and benzoyl chloride treatments may improve the mechanical properties of SPF/GF/PLA hybrid composites, and a short-term creep test revealed that the alkaline treated SPF/GF/PLA composite displayed the least creep deformation. The findings of the horizontal UL 94 testing indicated that the alkaline-treated SPF/GF/PLA hybrid composites had good flame resistance. However, alkaline-treated SPF/GF/PLA composites are more suitable materials for motorcycle components.

Physical, Mechanical, and Morphological Properties of Treated Sugar Palm/Glass Reinforced Poly(Lactic Acid) Hybrid Composites.

This research was performed to evaluate the physical, mechanical, and morphological properties of treated sugar palm fiber (SPF)/glass fiber (GF) reinforced poly(lactic acid) (PLA) hybrid composites. Morphological investigations of tensile and flexural fractured samples of composites were conducted with the help of scanning electron microscopy (SEM). Alkaline and benzoyl chloride (BC) treatments of SPFs were performed. A constant weight fraction of 30% total fiber loading and 70% poly(lactic acid) were considered. The composites were initially prepared by a Brabender Plastograph, followed by a hot-pressing machine. The results reported that the best tensile and flexural strengths of 26.3 MPa and 27.3 MPa were recorded after alkaline treatment of SPF, while the highest values of tensile and flexural moduli of 607 MPa and 1847 MPa were recorded after BC treatment of SPF for SPF/GF/PLA hybrid composites. The novel SPF/GF/PLA hybrid composites could be suitable for fabricating automotive components.

Amendments with pyrolyzed agrowastes change bromacil and diuron's sorption and persistence in a tropical soil without modifying their environmental risk.

Knowledge of pesticides fate in tropical soils and how it could be affected by pyrolyzed biomass as amendment is limited. Combining conventional and radiotracer methods, as well as risk assessment tools, the effects of several charred agrowastes on the sorption, persistence, and ecological risk of the herbicides bromacil (BMC) and diuron (DRN) were evaluated in a tropical agricultural soil under laboratory conditions. Pineapple stubble (PS), palm oil fiber (PF), and coffee hull (CH) were charred at 300 (torrefied) and 600 °C (biochar) and applied to the soil at 10 and 20 t ha-1 rates. The sorption coefficients (Koc) in unamended soil for BMC and DRN were 18.4 and 212.1 L kg-1, respectively. The addition of torrefied PS and PF caused a 3 to 4-fold increment in BMC sorption and a 3 to 6-fold change in DRN's sorption. The only biochar that affected the sorption was PS that increased DRN's sorption 3.5 times. The application of coffee hull materials had no significant effect. In terms of degradation (half-life, DT50), for unamended soil BMC's degradation (300 days) was limited compared to DRN (73 days). Alternatively, biodegradation (mineralization half-life time, MT50) was 1278 d for BMC and 538 for DRN. While only PF and CH torrefied increased BMC's persistence, all the torrefied affected DRN's persistence. However, despite the observed effects, the predicted ecological risk was not mitigated. Our results highlight the need for scientific evidence on the use of pyrolyzed organic amendments to assess potential benefits and prevent unintended impacts in tropical agroecosystems.

Enhanced Mechanical and Thermal Properties of Modified Oil Palm Fiber-Reinforced Polypropylene Composite via Multi-Objective Optimization of In Situ Silica Sol-Gel Synthesis.

A multi-objective optimization of in situ sol-gel process was conducted in preparing oil palm fiber-reinforced polypropylene (OPF-PP) composite for an enhancement of mechanical and thermal properties. Tetraethyl orthosilicate (TEOS) and butylamine were used as precursors and catalysts for the sol-gel process. The face-centered central composite design (FCCD) experiments coupled with response surface methodology (RSM) has been utilized to optimize in situ silica sol-gel process. The optimization process showed that the drying time after the in-situ silica sol-gel process was the most influential factor on silica content, while the molar ratio of TEOS to water gave the most significant effect on silica residue. The maximum silica content of 34.1% and the silica residue of 35.9% were achieved under optimum conditions of 21.3 h soaking time, 50 min drying time, pH value of 9.26, and 1:4 molar ratio of TEOS to water. The untreated oil palm fiber (OPF) and silica sol-gel modified OPF (SiO2-OPF) were used as the reinforcing fibers, with PP as a matrix and maleic anhydride grafted polypropylene (MAgPP) as a compatibilizer for the fiber-reinforced PP matrix (SiO2-OPF-PP-MAgPP) composites preparation. The mechanical and thermal properties of OPF-PP, SiO2-OPF-PP, SiO2-OPF-PP-MAgPP composites, and pure PP were determined. It was found that the OPF-S-PP-MAgPP composite had the highest toughness and stiffness with values of tensile strength, Young's modulus, and elongation at break of 30.9 MPa, 881.8 MPa, and 15.1%, respectively. The thermal properties analyses revealed that the OPF-S-PP-MAgPP exhibited the highest thermally stable inflection point at 477 °C as compared to pure PP and other composites formulations. The finding of the present study showed that the SiO2-OPF had the potential to use as a reinforcing agent to enhance the thermal-mechanical properties of the composites.