Design of a Supraharmonic Monitoring System Based on an FPGA Device.

During the last few decades, the poor quality of produced electric power is a key factor that has affected the operation of critical electrical infrastructure such as high-voltage equipment. This type of equipment exhibits multiple different failures, which originate from the poor electric power quality. This phenomenon is basically due to the utilization of high-frequency switching devices that operate over modern electrical generation systems, such as PV inverters. The conduction of significant values of electric currents at high frequencies in the range of 2 to 150 kHz can be destructive for electrical and electronic equipment and should be measured. However, the measuring devices that have the ability of analyzing a signal in the frequency domain present the ability of analyzing up to 2.5 kHz-3 kHz, which are frequencies too low in comparison to the high switching frequencies that inverters, for example, work. Electric currents at 16 kHz were successfully measured on an 8 kWp roof PV generator. This paper presents a fast-developed modern measuring system, using a field programmable gate array, aiming to detect electric currents at high frequencies, with a capability for working up to 150 kHz. The system was tested in the laboratory, and the results are satisfactory.

Sport-related femoral artery occlusion detected by near-infrared spectroscopy and pedal power measurements: a case report.

OBJECTIVES: Approximately one in five professional cycling athletes will eventually develop a sport-related vascular problem. However, detecting such flow limitation is a diagnostic challenge as the sensitivity of the currently available standard diagnostic tools is limited. METHODS: Here we present an athlete with exercise-induced pain and weakness of the left leg. During the physical examination, pulsations of the femoral artery were palpable but less prominent. He was analyzed in an ongoing research project aimed at improving methods detecting sport-related leg flow limitations. RESULTS: During functional testing, the ankle-brachial index of the left leg was moderately lowered. However, results of near-infrared spectroscopy and pedal power measurements were largely abnormal suggesting a severe flow limitation. CONCLUSION: Combining post-exercise ankle-brachial index, near-infrared spectroscopy, and pedal power measurements as routine diagnostic functional testing suggested a severe arterial flow inflow limitation. Conventional diagnostics encompassing duplex-Doppler echography and magnetic resonance angiography confirmed a femoral artery occlusion. CLINICAL TRIAL REGISTRATION: https://www.trialregister.nl/ identifier is Trial NL8557.Abbreviations: NIRS: Near-Infrared Spectroscopy; PPM: Pedal Power Measurements; ABI: Ankle Brachial Index; PSV: Peak Systolic Velocity.

Reproducibility of 'COST reference microplasma jets'.

Atmospheric pressure plasmas have been ground-breaking for plasma science and technologies, due to their significant application potential in many fields, including medicinal, biological, and environmental applications. This is predominantly due to their efficient production and delivery of chemically reactive species under ambient conditions. One of the challenges in progressing the field is comparing plasma sources and results across the community and the literature. To address this a reference plasma source was established during the 'biomedical applications of atmospheric pressure plasmas' EU COST Action MP1101. It is crucial that reference sources are reproducible. Here, we present the reproducibility and variance across multiple sources through examining various characteristics, including: absolute atomic oxygen densities, absolute ozone densities, electrical characteristics, optical emission spectroscopy, temperature measurements, and bactericidal activity. The measurements demonstrate that the tested COST jets are mainly reproducible within the intrinsic uncertainty of each measurement technique.

Ultrasonic Power Output Measurement by Pulsed Radiation Pressure.

Direct measurements of time-averaged spatially integrated output power radiated into reflectionless water loads can be made with high accuracy using techniques which exploit the radiation pressure exerted by sound on all objects in its path. With an absorptive target arranged to intercept the entirety of an ultrasound beam, total beam power can be determined as accurately as the radiation force induced on the target can be measured in isolation from confounding forces due to buoyancy, streaming, surface tension, and vibration. Pulse modulation of the incident ultrasound at a frequency well above those characteristics of confounding phenomena provides the desired isolation and other significant advantages in the operation of the radiation force balance (RFB) constructed in 1974. Equipped with purpose-built transducers and electronics, the RFB is adjusted to equate the radiation force and a counterforce generated by an actuator calibrated against reference masses using direct current as the transfer variable. Improvements made during its one overhaul in 1988 have nearly halved its overall measurement uncertainty and extended the capabilities of the RFB to include measuring the output of ultrasonic systems with arbitrary pulse waveforms.