Recycling Perovskite Solar Cells To Avoid Lead Waste.

Methylammonium lead iodide (MAPbI3) perovskite based solar cells have recently emerged as a serious competitor for large scale and low-cost photovoltaic technologies. However, since these solar cells contain toxic lead, a sustainable procedure for handling the cells after their operational lifetime is required to prevent exposure of the environment to lead and to comply with international electronic waste disposal regulations. Herein, we report a procedure to remove every layer of the solar cells separately, which gives the possibility to selectively isolate the different materials. Besides isolating the toxic lead iodide in high yield, we show that the PbI2 can be reused for the preparation of new solar cells with comparable performance and in this way avoid lead waste. Furthermore, we show that the most expensive part of the solar cell, the conductive glass (FTO), can be reused several times without any reduction in the performance of the devices. With our simple recycling procedure, we address both the risk of contamination and the waste disposal of perovskite based solar cells while further reducing the cost of the system. This brings perovskite solar cells one step closer to their introduction into commercial systems.

Control of Perovskite Crystal Growth by Methylammonium Lead Chloride Templating.

State-of-the-art solar cells based on methylammonium lead iodide (MAPbI3 ) now reach efficiencies over 20 %. This fast improvement was possible with intensive research in perovskite processing. In particular, chloride-based precursors are known to have a positive influence on the crystallization of the perovskite. Here, we used a combination of in-situ X-ray diffraction and charge-transport measurements to understand the influence of chloride during perovskite crystallization in planar heterojunction solar cells. We show that MAPbCl3 crystallizes directly after the deposition of the starting solution and acts as a template for the formation of MAPbI3 . Additionally, we show that the charge-carrier mobility doubles by extending the time for the template formation. Our results give a deeper understanding of the influence of chloride in the synthesis of MAPbI3 and illustrate the importance of carefully controlling crystallization for reproducible, high-efficiency solar cells.

Stabilization of the Trigonal High-Temperature Phase of Formamidinium Lead Iodide.

Formamidinium lead iodide (FAPbI3) has the potential to achieve higher performance than established perovskite solar cells like methylammonium lead iodide (MAPbI3), while maintaining a higher stability. The major drawback for the latter material is that it can crystallize at room temperature in a wide bandgap hexagonal symmetry (P63mc) instead of the desired trigonal (P3m1) black phase formed at a higher temperature (130 °C). Our results show that employing a mixture of MAI and FAI in films deposited via a two-step approach, where the MAI content is <20%, results in the exchange of FA molecules with MA without any significant lattice shrinkage. Additionally, we show with temperature-dependent X-ray diffraction that the trigonal phase exhibits no phase changes in the temperature range studied (25 to 250 °C). We attribute the stabilization of the structure to stronger interactions between the MA cation and the inorganic cage. Finally, we show that the inclusion of this small amount of MA also has a positive effect on the lifetime of the photoexcited species and results in more efficient devices.

Efficient Planar Heterojunction Perovskite Solar Cells Based on Formamidinium Lead Bromide.

The development of medium-bandgap solar cell absorber materials is of interest for the design of devices such as tandem solar cells and building-integrated photovoltaics. The recently developed perovskite solar cells can be suitable candidates for these applications. At present, wide bandgap alkylammonium lead bromide perovskite absorbers require a high-temperature sintered mesoporous TiO2 photoanode in order to function efficiently, which makes them unsuitable for some of the above applications. Here, we present for the first time highly efficient wide bandgap planar heterojunction solar cells based on the structurally related formamidinium lead bromide. We show that this material exhibits much longer diffusion lengths of the photoexcited species than its methylammonium counterpart. This results in planar heterojunction solar cells exhibiting power conversion efficiencies approaching 7%. Hence, formamidinium lead bromide is a strong candidate as a wide bandgap absorber in perovskite solar cells.