Fiber Bragg gratings inscribed in nanobore fibers.

The nanobore fiber (NBF) is a promising nanoscale optofluidic platform due to its long nanochannel and unique optical properties. However, so far, the applications of NBF have been based only on its original fiber geometry without any extra functionalities, in contrast with various telecom fiber devices, which may limit its wide applications. Here, we provide the first, to the best of our knowledge, demonstration of NBF-based fiber Bragg gratings (FBGs) introduced by either the femtosecond (fs) laser direct writing technique or the ultraviolet (UV) laser phase mask technique. Moreover, the FBG fabricated via the UV laser was optimized, achieving a high reflectivity of 96.89% and simultaneously preserving the open nanochannel. The NBF-based FBGs were characterized in terms of temperature variation and the infiltration of different liquids, and they showed high potential for nanofluidic applications.

Simultaneous measurement of torsion and strain at high temperature by using a highly birefringent cladding fiber Bragg grating.

We demonstrate the fabrication of a new highly birefringent cladding fiber Bragg grating (Hi-Bi CFBG) consisting of a pair of sawtooth stressors near the fiber core by using a femtosecond laser direct writing technology. The unique sawtooth structure serves as in-fiber stressor and also generates Bragg resonance due to its periodicity. After optimization of laser pulse energy, the Hi-Bi CFBG with a high birefringence of 2.2 × 10-4 and a low peak reflectivity of ∼ -24.5 dB (corresponding to ∼ 0.3%) was successfully fabricated in a conventional single-mode fiber (SMF). And then, a wavelength-division-multiplexed Hi-Bi CFBGs array and an identical Hi-Bi CFBGs array were successfully constructed. Moreover, a simultaneous measurement of torsion and strain at high temperature of 700 °C was realized by using the fabricated Hi-Bi CFBG, in which the torsion can be deduced by monitoring the reflection difference between the two polarization peaks and strain can be detected by measuring polarization peak wavelength. A high torsion sensitivity of up to 80.02 dB/(deg/mm) and a strain sensitivity of 1.06 pm/µÉ› were achieved. As such, the proposed Hi-Bi CFBG can be used as a mechanical sensor in many areas, especially in structural health monitoring at extreme conditions.

High-Temperature-Resistant Fiber Laser Vector Accelerometer Based on a Self-Compensated Multicore Fiber Bragg Grating.

We propose and demonstrate a novel high-temperature-resistant vector accelerometer, consisting of a ring cavity laser and sensing probe (i.e., fiber Bragg gratings (FBGs)) inscribed in a seven-core fiber (SCF) by using the femtosecond laser direct writing technique. A ring cavity laser serves as a light source. Three FBGs in the outer cores of SCF, which are not aligned in a straight line, are employed to test the vibration. These three FBGs have 120° angular separation in the SCF, and hence, vibration orientation and acceleration can be measured simultaneously. Moreover, the FBG in the central core was used as a reflector in the ring cavity laser, benefiting to resist external interference factors, such as temperature and strain fluctuation. Such a proposed accelerometer exhibits a working frequency bandwidth ranging from 4 to 68 Hz, a maximum sensitivity of 54.2 mV/g, and the best azimuthal angle accuracy of 0.21° over a range of 0-360°. Furthermore, we investigated the effect of strain and temperature on the performance of this sensor. The signal-to-noise ratio (SNR) only exhibits a fluctuation of ~1 dB in the range (0, 2289 µÎµ) and (50 °C, 1050 °C). Hence, such a vector accelerometer can operate in harsh environments, such as in aerospace and a nuclear reactor.

Efficient point-by-point Bragg grating inscription in sapphire fiber using femtosecond laser filaments.

Sapphire fiber Bragg gratings (SFBGs) inscribed by using femtosecond laser point-by-point (PbP) technology typically have an extremely low reflectivity due to the limited cross-sectional area of refractive index modulations (RIMs) created in sapphire fiber. Hence, we propose and experimentally demonstrate a filamentation process for fabricating PbP SFBGs. This approach provides an efficient method for producing SFBGs at various Bragg wavelengths with a higher reflectivity, since the filament tracks could enlarge the cross-sectional area of RIMs. The influences of the pulse energy and the focal depth on the generation and morphology of the filament tracks were studied, and after optimizing these parameters, high-quality filament tracks with a length of 90 µm and a width of 1.4 µm were produced into sapphire fiber with a diameter of 100 µm. These filament tracks were precisely assembled in sapphire fiber, generating an SFBG with a reflectivity of 2.3%. The total fabrication time for this SFBG only requires ${\sim}{1.1}\;{\rm s}$. Subsequently, a wavelength-division-multiplexed (WDM) SFBG array consisting of five SFBGs was efficiently constructed. Moreover, the high-temperature response of the SFBG array was investigated and the experimental results showed that the SFBG array can withstand a high temperature of 1600°C. Such a WDM SFBG array could serve as quasi-distributed high-temperature sensor which will be promising in many areas, i.e., metallurgical, chemical, and aviation industries.

Femtosecond laser line-by-line inscription of apodized fiber Bragg gratings.

The reflection spectra of conventional fiber Bragg gratings (FBGs) with uniform index modulation profiles typically have strong sidelobes, which hamper the performance of FBG-based optical filters, fiber lasers, and sensors. Here, we propose and demonstrate a femtosecond laser line-by-line (LbL) scanning technique for fabricating apodized FBGs with suppressed sidelobes. This approach can flexibly achieve various apodized modulation profiles via precise control over the length and/or transverse position of each laser-inscribed index modification track. We theoretically and experimentally studied the influences of the apodization function on the side-mode suppression ratio (SMSR) in the fabricated apodized FBG, and the results show that a maximum SMSR of 20.6 dB was achieved in a Gaussian-apodized FBG. Subsequently, we used this method to fabricate various apodized FBGs, and the SMSRs in these FBGs were reduced effectively. Specifically, a dense-wavelength-division-multiplexed Gaussian-apodized FBG array with a wavelength interval of 1.50 nm was successfully fabricated, and the SMSR in such an array is 14 dB. Moreover, a Gaussian-apodized phase-shifted FBG and chirped FBG were also demonstrated with a high SMSR of 14 and 16 dB, respectively. Therefore, such an apodization method based on a modified femtosecond laser LbL scanning technique is an effective and flexible way to fabricate various FBGs with high SMSRs, which is promising to improve the performance of optical filters, fiber lasers, and sensors.

High-Quality Fiber Bragg Gratings Inscribed by Femtosecond Laser Point-by-Point Technology.

We experimentally studied the inscription of fiber Bragg gratings by using femtosecond (fs) laser point-by-point (PbP) technology. The effects of the focusing geometry, grating order, laser energy and grating length on the spectral characteristics of the PbP FBG were investigated. After optimizing these parameters, a high-quality first-order PbP FBG with a reflectivity > 99.9% (i.e., Bragg resonance attenuation of 37.7 dB) and insertion loss (IL) of 0.03 dB was successfully created. Moreover, taking advantage of the excellent flexibility of the fs laser PbP technology, high-quality FBGs with various Bragg wavelengths ranging from 856 to 1902.6 nm were inscribed. Furthermore, wavelength-division-multiplexed (WDM) FBG arrays consisting of 10 FBGs were rapidly constructed. Additionally, a Fabry-Perot cavity was realized by using two high-quality FBGs, and its birefringence could be reduced from 3.04 × 10−5 to 1.77 × 10−6 by using a slit beam shaping-assisted femtosecond laser PbP technology. Therefore, such high-quality FBGs are promising to improve the performance of optical fiber sensors, lasers and communication devices.

Stabilized Ultra-High-Temperature Sensors Based on Inert Gas-Sealed Sapphire Fiber Bragg Gratings.

In situ measurement of high temperature is critical in aerospace, petrochemical, metallurgical, and power industries. The single-crystal sapphire fiber is a promising material for high-temperature measurement owing to its high melting point of ∼2045 °C. Sapphire fiber Bragg gratings (SFBGs), which could be inscribed in sapphire fibers with a femtosecond laser, are widely used as high-temperature sensors. However, conventional SFBGs typically exhibit a significant deterioration in their spectra after long-term operation at ultra-high temperatures, resulting from the formation of some unwanted microstructural features, that is, lossy spots and micro-etched lines, on the surface of the sapphire fiber. Here, we report for the first time, to the best of our knowledge, a thermally stabilized ultra-high-temperature sensor based on an SFBG created by femtosecond laser inscription, inert gas-sealed packaging, and gradient temperature-elevated annealing. The results indicate that the lossy spots are essentially aluminum hydroxide induced by high-temperature oxidation, and the inert gas-sealed packaging process can effectively insulate the sapphire fiber from the ambient air. Moreover, the formation of micro-etched lines was suppressed successfully by using the gradient temperature-elevated annealing process. As a result, the surface topography of the SFBG after operating at high temperatures was improved obviously. The long-term thermal stability of such an SFBG was greatly enhanced, showing a stable operation at 1600 °C for up to 20 h. In addition, it could withstand an even higher temperature of 1800 °C with a sensitivity of 41.2 pm/°C. The aforementioned results make it promising for high-temperature sensing in chemical, aviation, smelting, and power industries.