Photochemical transformation of azoxystrobin in aqueous solutions.

The photochemical behaviour of azoxystrobin fungicide (AZX) in water was studied under laboratory conditions. Photodegradation was initiated using a solar simulator (xenon arc lamp) or a jacketed Pyrex reaction cell equipped with a 125 W, high-pressure mercury lamp. HPLC/MS analysis (APCI and ESI in positive and negative modes) was used to identify AZX photoproducts. The calculated polychromatic quantum efficiencies (phi) of AZX at pH 4.5, 7 and 9 were 5.42 x 10(-3), 3.47 x 10(-3) and 3.06 x 10(-3) (degraded molecules per absorbed photon), respectively. The relatively narrow range of values indicates the stability of AZX with respect to photodegradation in the studied pH range. Results from the HPLC/MS analysis suggest that the phototransformation of AZX proceeds via multiple, parallel reaction pathways including: (1) photo-isomerization (E-->Z), (2) photo-hydrolysis of the methyl ester and of the nitrile group, (3) cleavage of the acrylate double bond, (4) photohydrolytic ether cleavage between the aromatic ring giving phenol, and (5) oxidative cleavage of the acrylate double bond.

Spectral properties of new N,N'-bis-alkyl-1,4,6,8-naphthalenediimide complexes.

The photophysical properties of two N,N'-bis-alkyl-1,4,6,8-naphthalenediimide (DCN1 and DCN2) have been studied in chloroform and N,N-dimethylformamide solvents. The ability of DCN2 in N,N-dimethylformamide to detect metal cations have been monitored by the fluorescence emission spectroscopy. It has been shown that the fluorescent intensity is very sensitive to the concentration of Fe3+ cations. The reaction of iodine with N,N'-bis-alkyl-1,4,6,8-naphthalenediimide in chloroform solution have been investigated by spectrophotometric method. The results indicate the formation of two CT-complexes [(DCN1)I]+.I3- and [(DCN2)I]+.I3- at donor:acceptor molar ratio of 1:2. The [(DCN1)I]+.I3- shows the characteristic absorptions of I3- ion at 290 and 360 nm while the charge-transfer transition of [(DCN2)I]+.I3- occurs at 310 nm. Three characteristic bands at the far infrared region in each iodine complex are observed around 135, 105 and 85 cm-1 due to nuas (I-I), nus (I-I) and delta (I3-), respectively with C2v symmetry. The values of the complex formation constant, K, and the absorptivity, epsilon have been calculated.

Abiotic degradation of iodosulfuron-methyl-ester in aqueous solution.

The abiotic degradation of iodosulfuron-methyl-ester was investigated under both alkaline and acidic pH conditions in the dark, and results showed it to be a rather stable molecule in neutral or slightly alkaline environments. Photochemical reactions were studied using a high-pressure mercury arc lamp, and results showed that direct phototransformation is possible under normal environmental conditions (lambda > 290 nm). High-performance liquid chromatography (HPLC-UV and HPLC-MS) analyses were used to identify the degradates and to study the kinetics of photodecomposition and hydrolysis. Five main products of iodosulfuron-methyl-ester degradation were tentatively identified, and one of them (4-methoxy-6-methyl-1,3,5-triazin-2-amine) was confirmed using an authentic standard. Among the phototransformation mechanisms, photosubstitution of the iodide atom by a hydroxyl group, photodissociation of the N-S bond, and photoassisted hydrolysis were observed. The quantum efficiencies (multiwavelength quantum yield) of the photodegradation under different conditions were determined, and values of 0.054 +/- 0.02 (pH 9.6), 0.08 +/- 0.02 (pH 7), and 0.044 +/- 0.008 (pH 5.3) were obtained.

Development of enzyme biosensor based on pH-sensitive field-effect transistors for detection of phenolic compounds.

This article describes a biosensor based on pH-sensitive field-effect transistors (pH-FETs) as transducer, and immobilised enzyme tyrosinase as biorecognition element, which was used for the determination of phenolic compounds in water solutions. The biologically active membrane was formed by cross-linking of tyrosinase with bovine serum albumin (BSA) in saturated glutaraldehyde (GA) vapours on the sensitive transducer surface. The main analytical characteristics were studied under different conditions as well as the possibility to optimise these working parameters. Different factors such as the pH of immobilisation, the enzyme loading, the time of exposition to glutaraldehyde vapours were investigated in regards to the influence on sensitivity, limit of detection, dynamic range, and operational and storage stability.

Simulated sunlight-induced photodegradations of triasulfuron and cinosulfuron in aqueous solutions.

To elucidate the photochemical behavior of two sulfonylureas (cinosulfuron and triasulfuron) for which the chemical formulas are relatively close, their photodegradation was studied in water. All experiments were carried out under laboratory conditions using a xenon arc lamp as the source of radiation to simulate environmental conditions. Polychromatic quantum efficiencies were calculated to determine the photochemical pesticide lifetimes at pH 7, and a comparison with hydrolysis lifetimes has been performed. The results obtained showed clearly that at pH 7, photodegradation becomes a more important pathway than chemical degradation. HPLC-DAD was used to study the kinetics for both sulfonylureas and their photoproducts, whereas HPLC-MS (ESI in positive and negative modes) was used to identify photoproducts. These results suggest that the photodegradation of these two sulfonylureas proceeds via a number of reaction pathways: (1) cleavage of the sulfonylurea bridge; (2) desulfonylation, which can proceed either by a carbon-sulfur cleavage or a nitrogen-sulfur cleavage; (3) O-demethylation of methoxy moieties present on the triazine ring; and (4) O-dealkylation of benzene derivatives. In addition, it was found that the desulfonylation represented the main step and that it was wavelength dependent.

Photochemical degradation of acifluorfen in aqueous solution.

To elucidate the photochemical behavior of diphenyl ether herbicides in superficial waters, the photodegradation of acifluorfen, 5-[2-chloro-4-(trifluoromethyl)phenoxy]-2-nitrobenzoïc acid (CAS Registry No. 50594-66-6), was studied in water and acetonitrile. All experiments were carried out under laboratory conditions using a solar simulator (xenon arc) or jacket Pyrex reaction cell equipped with a 125 W high-pressure mercury lamp. The calculated polychromatic quantum efficiencies (Phi(solvent)) of acifluorfen in different solvents are as follows (units are degraded molecules photon(-1)): Phi(water) = 10(-4), Phi(acetonitrile) = 10(-4), Phi(methanol) = 10(-4), and Phi(hexane) = 10(-2). The results obtained in this work are in good agreement with the literature value of monochromatic quantum yield. HPLC-MS analysis (APCI and ESI in positive and negative modes) was used to identify acifluorfen photoproducts. These results suggest that the photodegradation of acifluorfen proceeds via a number of reaction pathways: (1) decarboxylation, (2) dehalogenation, (3) substitution of chlorine group by hydroxyl or hydrogen groups, and (4) cleavage of ether linkage, giving phenols. Photorearrangement products were studied by other investigators. No such products were observed. In addition, it was found that the trifluoro functional group on acifluorfen was not affected by any transformation, and no products of a nitro group reduction were found.

Degradation of pentachlorophenol in cyclodextrin extraction effluent using a photocatalytic process.

This work evaluates a process for the elimination of pentachlorophenol (PCP) from effluents provided by a cyclodextrin-assisted flushing of contaminated soils. The effectiveness of photocatalytic degradation of PCP in several cyclodextrin (CD) solutions was evaluated using TiO2 as a photocatalyst. Effects of CD type on PCP degradation rate were studied at two pH values. A similar effect was observed for all CDs used on degradation rate of PCP and the decay of PCP was found to be less extensive at pH 11 than at pH 7. The kinetic orders of the photocatalytic reactions of PCP for all of the solutions have been determined. The first-order rate constants were found to be 0.0884, 0.0362, 0.0197 and 0.0053 min(-1) in CD solutions, respectively, at 0, 1, 2 and 5 mmol l(-1) of CD. Batch experiments were performed in order to study the CD extraction enhancement of PCP previously adsorbed on soil. The results show that the removal capacity of PCP from soil increases with CD concentration (from 0 to 5 mmol l(-1)). When the CD concentration was 5 mmol l(-1), an extraction of about 70% of PCP adsorbed on soil was observed, whereas only 37% was removed when water was used as the flushing solution. The optimal conditions for such a coupled method depend on the nature and concentration of the extracting agent and also on the photocatalytic experimental conditions. This work revealed that the coupling of cyclodextrin-enhanced solubilization and photocatalytic treatment is a promising method for contaminated soil remediation.

Photochemical behaviour of carbendazim in aqueous solution.

To elucidate the photochemical behaviour of carbendazim (or MBC) in superficial waters, photolysis studies have been carried out in aqueous solutions at several pH using a UV light source (high pressure mercury arc lamp) or a solar light simulator (xenon arc lamp). The kinetics of photodecomposition of carbendazim was determined using HPLC-DAD and the identification of photoproducts was carried out with HPLC-MS (ESI negative and positive mode). According to the experimental results carbendazim is a rather stable molecule in the dark or in environmental conditions. The pH influence of the environmental medium on the photodegradation rate has been confirmed. The photochemical process can be considerably accelerated in alkaline solutions using HPK-quartz irradiation (quantum efficiency at pH 9 phi = 3.1 x 10(-3) degraded molecule per absorbed photon) while the photodegradation is not as efficient under a simulated sun irradiation (quantum efficiency in the suntest phi = 10(-4) at pH 7). Three photoproducts have been tentatively identified in pure water: 2-aminobenzimidazole, benzimidazole isocyanate and monocarbomethoxy-guanidine (issued from the cleavage of the benzimidazole ring). The last one seems very stable and could be accumulated in the environment.

Sensitive immunodetection through impedance measurements onto gold functionalized electrodes.

This article deals with a direct electrochemical method of detecting antigens using new methods of functionalization of gold electrodes. Based on the reacting ability of gold with sulfhydryl groups, three protocols for the fixation of antibodies have been explored. They are based on either the self-assembling properties of functional thiols bearing long alkyl chains or the possibility of a direct coupling of antibody moieties. Coverage rates as high as 97% can be reached. The analysis of the electrochemical impedance behavior of such layers can lead to a sensitive method for the direct detection of the antibody/antigen interaction. The addition of a redox couple in the tested solution, acting as an amplifier, allowed detection limits for the antigens as low as a few picograms/milliliter to be reached.

Evaluation of adsorbents for volatile methyl siloxanes sampling based on the determination of their breakthrough volume.

Volatile methyl siloxanes (VMS) have been detected in many different atmospheres such as biogas, sewage sludge, landfill gas, gasoline and ambient air. In these different atmospheres, their presence can involve several contamination problems and negative effects in industrial processes, their identification and quantification become a real challenge. Up to now there is no standardized procedure for VMS quantification, the sampling step remaining the major obstacle. Sampling gas through sorbent tube followed by analysis on TD-GC-MS is one of the reliable possibilities. It gathers sampling and preconcentration in one step and allows discrimination between all VMS, despite the difficulty to choose the appropriate adsorbent in order to avoid loss of analytes during sampling. In this context, this work deals with the comparison of different types of adsorbents based on the determination of the VMS breakthrough volume (BV). Although Tenax TA is the most widely used adsorbent, experiments show low BV values for the lightest VMS. At 25°C, the BV of TMS and L2 are, respectively, 0.2 and 0.44 L g(-1) which can contribute to an underestimation in concentration during their quantification. Carbosieve SIII usually used for C2-C5, did not adsorb light VMS as it was expected, and breakthrough volume obtained for VMS are more than ten times less than the values obtained for Tenax. On other hand, Chromosorb 106 and Carboxen 1000 in association with Carbotrap C and Carbotrap proved to be appropriated for VMS sampling, due to the high breakthrough volumes obtained for the lightest compounds comparing to the other adsorbents. The BVs of TMS for Carboxen 1000 and Chromosorb 106 are 1.2 × 10(4) and 39 L g(-1), respectively, and 49 × 10(4) and 1142 L g(-1) for L2, respectively.

Hydrocarbon removal from bilgewater by a combination of air-stripping and photocatalysis.

In order to prevent hydrocarbon discharge at sea from the bilge of ships, the International Maritime Organization (IMO) enacted the MARPOL 73/78 convention in which effluents are now limited to those with maximum oil content of 15 ppmv. Thus, photocatalysis and air-stripping were combined for the hydrocarbon removal from a real oily bilgewater sample and an original monitoring of both aqueous and gaseous phases was performed by GC/MS to better understand the process. Our results show that the hydrocarbon oil index [HC] can be reduced to its maximum permissible value of 15 ppmv (MARPOL) in only 8.5h when photocatalysis and air-stripping are used together in a synergistic way, as against 17 h when photocatalysis is used alone. However, this air-assisted photocatalytic process emits a large quantity of volatile organic compounds (VOC) and, within the first four hours, ca. 10% of the hydrocarbon removal in the aqueous phase is actually just transferred into the gaseous one. Finally, we highlight that the n-alkanes with a number of carbon atoms higher than 15 (N(C)>15) are those which most decrease the rate of [HC] removal.

Study of the VOC emissions from a municipal solid waste storage pilot-scale cell: comparison with biogases from municipal waste landfill site.

The emission of volatile organic compounds (VOCs) from municipal solid waste stored in a pilot-scale cell containing 6.4 tonnes of waste (storage facility which is left open during the first period (40 days) and then closed with recirculation of leachates during a second period (100 days)) was followed by dynamic sampling on activated carbon and analysed by GC-MS after solvent extraction. This was done in order to know the VOC emissions before the installation of a methanogenesis process for the entire waste mass. The results, expressed in reference to toluene, were exploited during the whole study on all the analyzable VOCs: alcohols, ketones and esters, alkanes, benzenic and cyclic compounds, chlorinated compounds, terpene, and organic sulphides. The results of this study on the pilot-scale cell are then compared with those concerning three biogases from a municipal waste landfill: biogas (1) coming from waste cells being filled or recently closed, biogas (2) from all the waste storage cells on site, and biogas (3) which is a residual gas from old storage cells without aspiration of the gas. The analysis of the results obtained revealed: (i) a high emission of VOCs, principally alcohols, ketones and esters during the acidogenesis; (ii) a decrease in the alkane content and an increase in the terpene content were observed in the VOCs emitted during the production of methane; (iii) the production of heavier alkanes and an increase in the average number of carbon atoms per molecule of alkane with the progression of the stabilisation/maturation process were also observed. Previous studies have concentrated almost on the analysis of biogases from landfills. Our research aimed at gaining a more complete understanding of the decomposition/degradation of municipal solid waste by measuring the VOCs emitted from the very start of the landfill process i.e. during the acidogenesis and acetogenesis phases.

Investigation of norflurazon pesticide photodegradation using plasma desorption time-of-flight mass spectrometry analysis.

We have previously demonstrated that PD-TOFMS (plasma desorption time-of-flight mass spectrometry) analysis is a powerful technique for the in situ analysis of pesticides deposited or adsorbed on solid materials. With the aim of producing reproducible data on the modification of a pesticide under controlled photodegradation conditions, we have now undertaken a study where both the substrate and the pesticide are well characterized. This is the case for norflurazon deposited onto an aluminium substrate, in particular regarding the reproducibility of preparation of the samples and the change with time of their chemical composition. Degradation parameters have been derived from the variation in yield of ions representative of the molecule and of its breakdown products and, particularly, from the time required for 50% dissipation of their initial concentration (DT50). DT50 values ranging between 1 and 10 h have been found. An interpretation of the degradation process is proposed from the decay of other ions. As expected, the degradation is faster when the UV sunlight is unfiltered (a factor of 3.8 for the molecule, and around 5 for the breakdown products).

Photocatalytic degradation of pesticide methomyl: determination of the reaction pathway and identification of intermediate products.

The degradation of pesticide methomyl in aqueous solution by UV-irradiation in the presence of TiO2 "Degussa P-25" has been studied. It was found that mineralisation to carbon dioxide, water, sulfate and ammonia took place during the process. The rate of photodecomposition of methomyl was measured using high performance liquid chromatography (HPLC), while its mineralization was followed using ion chromatography (IC), and total organic carbon (TOC) analysis. The identification of reaction intermediate products was carried out using coupled techniques HPLC-MS (electrospray ionization in positive mode) and a degradation pathway was proposed. Under our conditions, complete disappearance of 1.23 x 10(-4) mol l(-1) of pure pesticide occurred within 45 min of illumination and 80% TOC removal occurred in less than 4 h. Three main intermediates were identified resulting from (i) the rupture of the ester bond (or the N-O bond), (ii) the hydroxylation of methyl group borne by the nitrogen atom and (iii) the product resulting from the decarboxylation of the oxidized hydroxylated methyl group (photo-Kolbe reaction). In order to be sure that the photocatalytic results were consistent, hydrolysis and photolysis tests were performed. Photocatalysis proved to be an excellent new advanced oxidation technology (AOT) to eliminate methomyl present in water.

Experimental microkinetic approach of the photocatalytic oxidation of isopropyl alcohol on TiO2. Part 1. Surface elementary steps involving gaseous and adsorbed C3H(x)O species.

The present study concerns an experimental microkinetic approach of the photocatalytic oxidation (PCO) of isopropyl alcohol (IPA) into acetone on a pure anatase TiO2 solid according to a procedure previously developed. Mainly, the kinetic parameters of each surface elementary step of a plausible kinetic model of PCO of IPA are experimentally determined: natures and amounts of the adsorbed species and rate constants (preexponential factor and activation energy). The kinetics parameters are obtained by using experiments in the transient regime with either a FTIR or a mass spectrometer as a detector. The deep oxidation (CO2 and H2O formation) of low concentrations of organic pollutants in air is one of the interests of the PCO. For IPA, literature data strongly suggest that acetone is the single route to CO2 and H2O and this explains that the present study is dedicated to the elementary steps involving gaseous and adsorbed C3H(x)O species. The microkinetic study shows that strongly adsorbed IPA species (two species denoted nd-IPA(sads) and d-IPA(sads) due to non- and dissociative chemisorption of IPA, respectively) are involved in the PCO of IPA. A strong competitive chemisorption between IPA(sads) and a strongly adsorbed acetone species controls the high selectivity in acetone of the PCO at a high coverage of the surface by IPA(sads). The kinetic parameters of the elementary steps determined in the present study are used in part 2 to provide a modeling of macroscopic kinetic data such as the turnover frequency (TOF in s(-1)) of the PCO using IPA/O2 gas mixtures.

Experimental microkinetic approach of the photocatalytic oxidation of isopropyl alcohol on TiO2. Part 2. from the surface elementary steps to the rates of oxidation of the C3H(x)O species.

The present study concerns an experimental microkinetic approach of the photocatalytic oxidation (PCO) of isopropyl alcohol (IPA) into acetone on a pure anatase TiO2 solid according to a procedure previously developed. Mainly, the kinetic parameters of each surface elementary step of a plausible kinetic model of the PCO of IPA are experimentally determined: natures and amounts of the adsorbed species and rate constants (preexponential factors and activation energies). These kinetic parameters are used to evaluate a priori the catalytic activity (turnover frequency, TOF, in s(-1)) of the solid that is compared to the experimental value. The kinetics parameters are obtained by using experiments in the transient regime with either a FTIR or a mass spectrometer as a detector. The microkinetic study shows that only strongly adsorbed IPA species (two species denoted nd-IPA(sads) and d-IPA(sads) due to non- and dissociative chemisorption of IPA respectively) are involved in the PCO of IPA. A strong competitive chemisorption between IPA(sads) and a strongly adsorbed acetone species controls the high selectivity in acetone of the PCO at a high coverage of the surface by IPA(sads). The apparent rate constant (1.4 10(-3) s(-1)) of the Langmuir-Hinshelwood elementary step between IPA(sads) and the active oxygen containing species generated by the UV irradiation provides the TOF of the PCO for IPA/O2 gas mixtures. The kinetic parameters of the elementary steps determined by the experimental microkinetic approach allow us to provide a reasonable simulation of the experimental data (coverages of the adsorbed species and partial pressures of the gases of interest) recorded during a static PCO of IPA(sads) species.

[Amperometric biosensor for lactate analysis in wines and grape must during fermentation].

The amperometric biosensor based on lactate oxidase for determination of lactate has been developed, and two methods of immobilization of lactate oxidase on the surface of industrial screen-printed platinum electrodes SensLab were compared. A sensor with immobilized in the Resydrol polymer lactate oxidase by the method of physical adsorption is characterized of narrow dynamic range and greater response value in comparison with a biosensor based on immobilised in poly(3,4-ethylenedioxythiophene) lactate oxidase by the method of electrochemical polymerization. Operational stability of the biosensor developed was studied and it was shown, that the immobilization method does not influence their stability. The analysis of the lactate in wine and during wine fermentation has been conducted. High correlation of the data obtained by means of amperometric lactate biosensor and a standard method of an ionic chromatography has been shown. The developed biosensor could be applied in the food industry for the control and optimization of the wine fermentation process, and quality control of wine.

Fiber-optic surface-plasmon resonance for the determination of thickness and optical constants of thin metal films.

We demonstrate that the thickness and the dielectric constants of thin gold films deposited on the surface of a fiber core can be quantitatively determined as a single set of solutions by the simple measurement of the fiber-optic surface-plasmon resonance responses. This method is capable of directly characterizing metal films with curved surfaces: this is very hard to perform by use of the conventional optical techniques of reflectometry and ellipsometry. The theoretical errors for the experimental fiber are estimated to be within d +/- 2%, epsilon(r) +/- 1%, and epsilon(i) +/- 15%.

Enzyme-octadecylamine Langmuir-Blodgett membranes for ENFET biosensors.

Langmuir-Blodgett (LB) films containing butyrylcholinesterase (BuChE) are fabricated to realise an enzymatic field effect transistor (ENFET) for the detection of organophosphorus pesticides in water. Trichlorfon as a common pesticide is examined in our work. The BuChE-immobilised LB films are formed by adsorbing the enzyme molecules onto a stearylamine monolayer using the electrostatic force. Enzyme/stearylamine mixed LB films are immobilized onto a pH-ISFET surface and treated by glutaraldehyde vapour to improve the LB film's stability. The ENFET thus obtained worked as a potentiometric biosensor for trichlorfon detection on the basis of enzyme inhibition. The detection limit for trichlorfon can reach 10(-7) M (26 ppb). The surface characteristics of BuChE/stearylamine LB films obtained under various conditions of the dipping surface pressures are analysed qualitatively by atomic force microscopy (AFM) and analysed quantitatively by FTIR spectroscopy.

New use of cyanosilane coupling agent for direct binding of antibodies to silica supports. Physicochemical characterization of molecularly bioengineered layers.

A simple protocol to fix biological species to silica-based surfaces (silica microbeads and glass slides), using a bifunctional silane reagent (3-cyanopropyl dimethyl chlorosilane), is presented. This silane reagent was used without further derivatization. This system led to strong, but not covalent, linkage of antibodies through their glycosylated regions (OH groups) to solid supports. The use of a microsized sample revealed that the coupling process depends not only on physicochemical interactions but also on steric phenomena, and in this case, it was shown that a molecule acting as a spacer was required for more efficient cell fixation. Here, monoclonal mouse antibodies against the CD45 molecule expressed on rat lymphocytes (MAR anti CD45 Ab) were linked to lymphocytes, and as spacers, sheep anti-mouse antibodies (SAM Ab) were immobilized on silica surfaces, allowing the cells to stick to the floating hollow silica microbeads by simple incubation. Under such conditions, a single microbead can fix several cells. The potential of this hollow, low-density support is in ultrasound applications, for the destruction by cavitation phenomena of cells selectively fixed onto such a support. Such a study can serve as a basic model for various microbiosystems involving cell manipulation.