Intercalation of Ionic Liquids into LDH Structures for Microwave-Accelerated Polymerizations.

Microwave-accelerated ring-opening polymerization (ROP) of cyclic esters catalyzed by ionic liquid (IL) anions, intercalated into layered double hydroxides (LDHs), has been recently described as a fast and environmentally friendly synthetic way to prepare biodegradable polyester/LDH nanocomposites. However, to observe this synergistic catalytic effect between microwaves and IL anions and to achieve a homogeneous structure of the final polymer nanocomposite, the IL anions must be efficiently intercalated inside the LDH structure. Herein, we investigate the effects of various metal compositions of M2+/Al3+ LDHs (M = Mg, Co, and Ca) and different LDH synthetic routes (one-step direct coprecipitation, two-step coprecipitation/anion exchange, and two-step urea/anion exchange) on the intercalation efficiency of trihexyltetradecylphosphonium bis(2,4,4-trimethylpentyl)phosphinate IL. The most effective IL anion intercalation was observed for Ca2+/Al3+ LDH prepared using the two-step method consisting of coprecipitation and subsequent anion exchange. After optimization, this synthetic pathway led to the production of LDHs with intercalated IL anions and a reduced amount of intercalated water (<0.6 wt %). The catalytic ability of thus optimized LDH particles was demonstrated on the microwave-assisted ROP of ε-caprolactone, showing rapid progress of polymerization. Within minutes, the polycaprolactones with an average molecular mass in the range of 20 000-50 000 g/mol containing fully delaminated and exfoliated LDH nanoparticles were obtained.

Preparation of High-Entropy (Ti, Zr, Hf, Ta, Nb) Carbide Powder via Solution Chemistry.

High-entropy ceramics is a new class of materials having a great potential and wide application. The carbide of Ti, Zr, Hf, Ta, Nb is a typical member of this group. It has been synthesized mostly through blending, milling, and high-temperature solid-state reaction of metal carbide precursors for each metal. This route needs extremely high temperature (2300 °C), which makes it energy and technology demanding. We have developed a chemical route for high-entropy carbide powder that needs a synthetic temperature that is several hundred degrees Celsius lower. A solution of desired metal citrates with an excess of citric acid was converted into a metal oxide/active carbon nanocomposite. Starting from a solution enabled ideal mixing of precursors on a molecular level, allowing us to skip any milling and blending steps. The nanocomposite was treated in vacuum at 1600 °C, giving a phase-pure high-entropy carbide. The intermediate compounds and products were characterized by means of solid-state analysis.

Iron-bismuth halido compounds: molecules, clusters, and polymers.

The pentamethylcyclopentadienyl substituted iron-bismuth halides [Bi{FeCp*(CO)2}X2] [X = Cl (1), Br (2), I (3); Cp* = η(5)-C5Me5] were synthesized starting from [FeCp*(CO)2]2 and BiX3 (X = Cl, Br), followed by halogen exchange reaction with KI in case of 3. From a reaction mixture of [FeCp*(CO)2]2 with BiCl3 in CH2Cl2 to which CH3CN had been added, a novel coordination polymer of the formula [FeCp*(CO)2(CH3CN)]2n[Bi4Cl14]n (4) was isolated. The change of the molar ratio from 1:1 to 1:2 in the reaction of [FeCp*(CO)2]2 with BiBr3 afforded the novel ionic complex [{FeCp*(CO)2Br]2[Bi6Br22{FeCp*(CO)2}]·CH2Cl2 (5·CH2Cl2). It is demonstrated that treatment of [FeCp*(CO)2X] (X = Cl, Br) with BiCl3 and BiBr3, respectively, is a more convenient route to synthesize the new halido bismuthates 4 and 5.

The effects of formation and functionalization of graphene-based membranes on their gas and water vapor permeation properties.

The gas and water vapor permeabilities of graphene-based membranes can be affected by the presence of different functional groups directly bound to the graphene network. In this work, one type of carboxylated graphene oxide (GO-COOH) and two types of graphene oxide synthesized i) under strong oxidative conditions directly from graphite (GO-1) and ii) under mild oxidative conditions from exfoliated graphene (GO-2) were used as precursors of self-standing membranes prepared with thicknesses in the range of 12-55 µm via slow-vacuum filtration preparation method. It was observed that the permeabilities for all tested gases decreased in order GO-2 > GO-1 > GO-COOH and depended on both the arrangement of graphene sheets and their functionalization. The GO-1 membrane with a high content of oxygen-containing groups showed the best performance for water vapor permeability. The GO-2 membrane with a thickness of 43 µm exhibited a disordered GO sheet morphology and, therefore, unique gas-separation performance towards H2/CO2 gas pair, showing high hydrogen permeability while keeping extremely high H2/CO2 ideal selectivity that exceeds the Robeson 2008 upper bound of polymer membranes.

Carbon and zeolite-based composites for radionuclide and heavy metal sorption.

Zeolites have been investigated as sorbents of heavy metals from water. Since graphene oxide was already reported as promising radionuclide sorbent, we developed composite materials containing both a synthetic zeolite (type A, P or Y) and graphene oxide to be multifunctional sorbents. The extension of multifunctionality of sorbents was done by presence of third component, exfoliated graphite, to have additional properties as conductivity. The changing sorption activities of a composite was studied depending on its composition and functional modification. The composites, characterized by X-ray powder diffraction, Raman, FTIR spectroscopy and scanning electron microscopy, were tested for sorption of selected radionuclides (134Cs+, 85Sr2+) and heavy metals (Pb2+, Cd2+). The dependency on composition was found in connection with a high sorption of Pb2+ and Cd2+. Finally, optimized multifunctional sorbents (Gr-GO-COOH-A in ratio 40:40:20 and Gr:GO:A in ratio 25:25:50) were found to keep interesting high sorption activities for heavy metals and radionuclides with good conductivity properties.

Study of Interactions between Titanium Dioxide Coating and Wood Cell Wall Ultrastructure.

Titanium dioxide (TiO2) is used as a UV light absorber to protect wood matter from photodegradation. In this paper, interactions between wood and TiO2 coating are studied, and the efficiency of the coating is evaluated. For the experiments, two wood species were chosen: beech (Fagus sylvatica) and pine (Pinus sylvestris). Molecular and physical modifications in coated and uncoated wood exposed to UV radiation were investigated with Fourier transform infrared spectroscopy with attenuated total reflectance (FTIR-ATR) and transmission electron microscopy (TEM). UV-VIS spectroscopy was used to describe the absorption of UV light by the TiO2 planar particles chosen for the experiment. It was demonstrated that TiO2 coating protects wood against photodegradation to a limited extent. TEM micrographs showed fissures in the wood matter around clusters of TiO2 particles in beech wood.

Salt-washed graphene oxide and its cytotoxicity.

The carbon nanomaterials and congeners, e.g., graphene or graphene oxide (GO), dispose of numerous unique properties, which are not necessarily intrinsic but might be related to a content of impurities. The oxidation step of GO synthesis introduces a considerable amount of metallic species. Therefore, large-scale purification is an actual scientific challenge. Here we describe new purification technique (salt­washing), which is based on three consecutive steps: (a) aggregation of GO sheets with NaCl (b) washing of the aggregates and (c) removing of the salt to afford purified GO (swGO). The considerably improved purity of swGO was demonstrated by ICP and EPR spectroscopy. The microscopic methods (TEM with SEAD, AFM) proved that the salt-washing does not affect the morphology or concentration of defects, showing the aggregation of GO with NaCl is fully reversible. The eligibility of swGO for biomedical applications was tested using fibroblastic cell cultures. The determined IC50 values clearly show a strong correlation between the purity of samples and cytotoxicity. Although the purification decreases cytotoxicity of GO, the IC50 values are still low proving that cytotoxic effect is not only impurities-related but also an intrinsic property. These findings may represent a serious limitation for usage of GO in biomedical applications.

Influence of Inorganic Bases on the Structure of Titanium Dioxide-Based Microsheets.

Laboratory synthesis of microsheets of titanium dioxide from titanyl sulfate involves the use of ammonia solution, whereas another inorganic base is most likely to be employed at the industrial level, as ammonia is a toxic agent and therefore should be avoided according to European Union (EU) regulations. Selected nontoxic bases such as sodium, potassium, and lithium hydroxides have been tested as an alternative to ammonia solution to obtain amorphous and crystalline TiO2-based microsheets. The final products obtained at each step of the procedure (samples lyophilized and annealed at 230 and 800 °C) were analyzed with electron and atomic force microscopy, X-ray powder diffraction, thermal analysis, and Fourier transform infrared (FTIR) and Raman spectroscopies to determine their morphology and phase composition. The differences in the morphology of the obtained products were described in detail as well as phase and structural composition throughout the process. It was found that, in the last step of the synthesis, microsheets annealed at 800 °C were built of small rods and oval or platy crystalline particles depending on the base used. The temperature of formation of anatase, rutile, and alkali-metal titanates in correlation with the ionic radius of the alkali metal present in the sample was discussed.

Ionic Liquids as Delaminating Agents of Layered Double Hydroxide during In-Situ Synthesis of Poly (Butylene Adipate-co-Terephthalate) Nanocomposites.

Currently, highly demanded biodegradable or bio-sourced plastics exhibit inherent drawbacks due to their limited processability and end-use properties (barrier, mechanical, etc.). To overcome all of these shortcomings, the incorporation of lamellar inorganic particles, such as layered double hydroxides (LDH) seems to be appropriate. However, LDH delamination and homogenous dispersion in a polymer matrix without use of harmful solvents, remains a challenging issue, which explains why LDH-based polymer nanocomposites have not been scaled-up yet. In this work, LDH with intercalated ionic liquid (IL) anions were synthesized by a direct co-precipitation method in the presence of phosphonium IL and subsequently used as functional nanofillers for in-situ preparation of poly (butylene adipate-co-terephthalate) (PBAT) nanocomposites. The intercalated IL-anions promoted LDH swelling in monomers and LDH delamination during the course of in-situ polycondensation, which led to the production of PBAT/LDH nanocomposites with intercalated and exfoliated morphology containing well-dispersed LDH nanoplatelets. The prepared nanocomposite films showed improved water vapor permeability and mechanical properties and slightly increased crystallization degree and therefore can be considered excellent candidates for food packaging applications.

Ultrasound exfoliation of graphite in biphasic liquid systems containing ionic liquids: A study on the conditions for obtaining large few-layers graphene.

Herein we describe a successful protocol for graphite exfoliation using a biphasic liquid system (water/dichloromethane, DCM) containing ionic liquids (ILs; 1,3-dibenzylimidazolium benzoate- and 1-naphthoate). The use of (surface active) IL and sonication led to stable DCM/water (O/W) emulsion, which enhanced graphene formation, suppressed its re-aggregation and decreased shear/cavitation damage. The O/W emulsion stabilization by the ILs was studied by dynamic light scattering (DLS), whereas their interaction with the graphene sheets were described by Density Functional Theory (DFT) calculations. Moreover, a comprehensive investigation on cavitation-based exfoliation in the O/W systems was performed to assess the importance of operational parameters, including, the type of ultrasound processor, ultrasound power and insonation, and the influence of the exfoliation medium.

Twinned Growth of Metal-Free, Triazine-Based Photocatalyst Films as Mixed-Dimensional (2D/3D) van der Waals Heterostructures.

Design and synthesis of ordered, metal-free layered materials is intrinsically difficult due to the limitations of vapor deposition processes that are used in their making. Mixed-dimensional (2D/3D) metal-free van der Waals (vdW) heterostructures based on triazine (C3 N3 ) linkers grow as large area, transparent yellow-orange membranes on copper surfaces from solution. The membranes have an indirect band gap (Eg,opt = 1.91 eV, Eg,elec = 1.84 eV) and are moderately porous (124 m2 g-1 ). The material consists of a crystalline 2D phase that is fully sp2 hybridized and provides structural stability, and an amorphous, porous phase with mixed sp2 -sp hybridization. Interestingly, this 2D/3D vdW heterostructure grows in a twinned mechanism from a one-pot reaction mixture: unprecedented for metal-free frameworks and a direct consequence of on-catalyst synthesis. Thanks to the efficient type I heterojunction, electron transfer processes are fundamentally improved and hence, the material is capable of metal-free, light-induced hydrogen evolution from water without the need for a noble metal cocatalyst (34 µmol h-1 g-1 without Pt). The results highlight that twinned growth mechanisms are observed in the realm of "wet" chemistry, and that they can be used to fabricate otherwise challenging 2D/3D vdW heterostructures with composite properties.

A green method of graphene preparation in an alkaline environment.

We present a new, simple, quick and ecologically friendly method of exfoliating graphite to produce graphene. The method is based on the intercalation of a permanganate M2MnO4 (M=K, Na, Li), which is formed by the reaction of a manganate MMnO4 with an alkali metal hydroxide MOH. The quality of exfoliation and the morphology were determined using X-ray photoelectron spectroscopy, X-ray diffraction and microscopic techniques, including transmission electron microscopy and atomic force microscopy. We observed that a stable graphene suspension could be prepared under strongly alkaline conditions in the presence of permanganate and ultrasound assistance. The use of only an alkaline environment for the direct preparation of graphene from graphite structures has not been previously described or applied. It was found that such a method of preparation leads to surprisingly high yields and a stable product for hydrophilic graphene applications.

Ultrasound exfoliation of inorganic analogues of graphene.

High-intensity ultrasound exfoliation of a bulk-layered material is an attractive route for large-scale preparation of monolayers. The monolayer slices could potentially be prepared with a high yield (up to 100%) in a few minutes. Exfoliation of natural minerals (such as tungstenite and molybdenite) or bulk synthetic materials (including hexagonal boron nitride (h-BN), hexagonal boron carbon nitride (h-BCN), and graphitic carbon nitride (g-C3N4)) in liquids leads to the breakdown of the 3D graphitic structure into a 2D structure; the efficiency of this process is highly dependent upon the physical effects of the ultrasound. Atomic force microscopy (AFM), transmission electron microscopy (TEM), and selected area electron diffraction (SAED) were employed to verify the quality of the exfoliation. Herein, this new method of exfoliation with ultrasound assistance for application to mono- and bilayered materials in hydrophobic and hydrophilic environments is presented.

Elusive ethynyl azides: trapping by 1,3-dipolar cycloaddition and decomposition to cyanocarbenes.

Although they decompose rapidly to produce cyanocarbenes, ethynyl azides were generated from (chloroethynyl)arenes and trapped for the first time by 1,3-dipolar cycloaddition at cyclooctyne.

Mixed-transition-metal acetylides: synthesis and characterization of complexes with up to six different transition metals connected by carbon-rich bridging units.

The synthesis and reaction chemistry of heteromultimetallic transition-metal complexes by linking diverse metal-complex building blocks with multifunctional carbon-rich alkynyl-, benzene-, and bipyridyl-based bridging units is discussed. In context with this background, the preparation of [1-{(eta(2)-dppf)(eta(5)-C(5)H(5))RuC[triple bond]C}-3-{(tBu(2)bpy)(CO)(3)ReC[triple bond]C}-5-(PPh(2))C(6)H(3)] (10) (dppf = 1,1'-bis(diphenylphosphino)ferrocene; tBu(2)bpy = 4,4'-di-tert-butyl-2,2'-bipyridyl; Ph = phenyl) is described; this complex can react further, leading to the successful synthesis of heterometallic complexes of higher nuclearity. Heterotetrametallic transition-metal compounds were formed when 10 was reacted with [{(eta(5)-C(5)Me(5))RhCl(2)}(2)] (18), [(Et(2)S)(2)PtCl(2)] (20) or [(tht)AuC[triple bond]C-bpy] (24) (Me = methyl; Et = ethyl; tht = tetrahydrothiophene; bpy = 2,2'-bipyridyl-5-yl). Complexes [1-{(eta(2)-dppf)(eta(5)-C(5)H(5))RuC[triple bond]C}-3-{(tBu(2)bpy)(CO)(3)ReC[triple bond]C}-5-{PPh(2)RhCl(2)(eta(5)-C(5)Me(5))}C(6)H(3)] (19), [{1-[(eta(2)-dppf)(eta(5)-C(5)H(5))RuC[triple bond]C]-3-[(tBu(2)bpy)(CO)(3)ReC[triple bond]C]-5-(PPh(2))C(6)H(3)}(2)PtCl(2)] (21), and [1-{(eta(2)-dppf)(eta(5)-C(5)H(5))RuC[triple bond]C}-3-{(tBu(2)bpy)(CO)(3)ReC[triple bond]C}-5-{PPh(2)AuC[triple bond]C-bpy}C(6)H(3)] (25) were thereby obtained in good yield. After a prolonged time in solution, complex 25 undergoes a transmetallation reaction to produce [(tBu(2)bpy)(CO)(3)ReC[triple bond]C-bpy] (26). Moreover, the bipyridyl building block in 25 allowed the synthesis of Fe-Ru-Re-Au-Mo- (28) and Fe-Ru-Re-Au-Cu-Ti-based (30) assemblies on addition of [(nbd)Mo(CO)(4)] (27), (nbd = 1,5-norbornadiene), or [{[Ti](mu-sigma,pi-C[triple bond]CSiMe(3))(2)}Cu(N[triple bond]CMe)][PF(6)] (29) ([Ti] = (eta(5)-C(5)H(4)SiMe(3))(2)Ti) to 25. The identities of 5, 6, 8, 10-12, 14-16, 19, 21, 25, 26, 28, and 30 have been confirmed by elemental analysis and IR, (1)H, (13)C{(1)H}, and (31)P{(1)H} NMR spectroscopy. From selected samples ESI-TOF mass spectra were measured. The solid-state structures of 8, 12, 19 and 26 were additionally solved by single-crystal X-ray structure analysis, confirming the structural assignment made from spectroscopy.