An innovative compact system for advanced treatment of combined sewer overflows (CSOs) discharged into large lakes: Pilot-scale validation.

Combined sewer overflows discharging into natural water bodies could potentially contaminate them in terms of conventional wastewater parameters and coliform bacteria. When green water infrastructures are not technically feasible or practically sustainable for stormwater management, innovative compact and effective end-of-pipe systems can be of interest. This study presents long-term and real-environment validated data of a compact and rapid treatment system specifically applicable to CSOs that consists of a dynamic rotating belt filter, adsorption on granular activated carbon and UV disinfection steps. The results of treatment for Lake Garda in Italy, showed great potential for TSS, COD and E. coli removal efficiencies with more than 90%, 69% and 99% respectively. Due to the short contact time of GAC adsorption, nutrients removals were not very high. TN and TP removal of around 41% and 19% were observed respectively that suggests further specific nutrients removal processes are required for achieving higher efficiencies. The treatment system, due to its compactness and rapidness could be a great asset for water utilities in different EU catchments that are dealing with the frequent CSO events. In addition, the possibility of using different combinations of treatment steps allows the choice of different treatment scenarios depending on the treatment goals for any specific catchment.

Nutrients recovery from anaerobic digestate of agro-waste: Techno-economic assessment of full scale applications.

The sustainable production of fertilizers, especially those based on phosphorus, will be one of the challenges of this century. Organic wastes produced by the agriculture, urban and industrial sectors are rich in nutrients which can be conveniently recovered and used as fertilizers. In this study five full scale systems for the recovery of nutrients from anaerobic digestate produced in farm-scale plants were studied. Monitored technologies were: drying with acidic recovery, stripping with acidic recovery and membrane separation. Results showed good performances in terms of nutrients recovery with average yields always over 50% for both nitrogen and phosphorus. The techno-economic assessment showed how the specificity of the monitored systems played a major role: in particular, membranes were able to produce a stream of virtually pure water (up to 50% of the treated digestate) reducing the digestate volume, while drying, because of the limitation on recoverable heat, could treat only a limited portion (lower than 50%) of produced digestate while stripping suffered some problems because of the presence of suspended solids in the liquid fraction treated. Specific capital and operational costs for the three systems were comparable ranging between 5.40 and 6.97 € per m3 of digestate treated and followed the order stripping > drying > membranes. Costs determined in this study were similar to those observed in other European experiences reported in literature.

Validation of a decision support tool for wastewater treatment selection.

Wastewater treatment selection is a complex task usually addressed by applying separate tools for the correct assessment of multi-criteria evaluation. Novedar_EDSS integrates technical, environmental, economic and social assessment capabilities in one single platform. The aim of this work is to evaluate and demonstrate the capabilities of this environmental decision support system (EDSS). For that purpose, 4 case studies of real projects were selected to validate the results in the EDSS by comparing them with those from the study of alternatives performed by the decision makers. Moreover, 1 conceptual case study was applied to support the selection of the most properly strategy for plant retrofitting. Results have demonstrated that the EDSS provides key aspects when deciding the retrofitting process to apply and, when compared to real projects, it recommends analogue treatments as those applied in the projects, ranking them in the same order. Therefore, results in the validation process performed show that this tool provides a reliable basis to support decision makers to select properly treatment alternatives in wastewater treatment plant pre-design.

Coupling the treatment of low strength anaerobic effluent with fermented biowaste for nutrient removal via nitrite.

Nutrient removal via nitrite was investigated in a sequencing batch reactor (SBR) treating low strength effluent produced from an upflow anaerobic sludge blanket (UASB). Domestic organic waste (DOW) and vegetable and fruit waste (VFW) were fermented and applied as external carbon source to the SBR. Nutrient removal via nitrite was much higher when DOW fermentation liquid (FL) was applied rather than VFW FL and acetic acid. The DOW FL contained propionic acid and butyric acid in significant proportions, favouring the nutrient removal via nitrite, while the VFW FL contained mainly acetic acid, which was associated with lower nutrient via nitrite activity. The application of high volumetric nitrogen loading rate (vNLR = 0.19-0.21 kgN m(-3) d(-1)) in combination with low dissolved oxygen (DO) concentration during the aerobic phase, resulted in high and stable nitrite accumulation (NO2-N/NOx-N >97%). These conditions favoured the phosphorus uptake via nitrite, which reached high rates (5.95 ± 2.21 mgP (gVSS h)(-1)), while the aerobic phosphorus removal was much lower. Through mass balances, it was demonstrated that the application of the UASB-SBR process with nutrient removal via nitrite at a decentralized level is a sustainable solution for effective co-treatment of domestic sewage and biowaste.

Biological nutrients removal from the supernatant originating from the anaerobic digestion of the organic fraction of municipal solid waste.

This study critically evaluates the biological processes and techniques applied to remove nitrogen and phosphorus from the anaerobic supernatant produced from the treatment of the organic fraction of municipal solid waste (OFMSW) and from its co-digestion with other biodegradable organic waste (BOW) streams. The wide application of anaerobic digestion for the treatment of several organic waste streams results in the production of high quantities of anaerobic effluents. Such effluents are characterized by high nutrient content, because organic and particulate nitrogen and phosphorus are hydrolyzed in the anaerobic digestion process. Consequently, adequate post-treatment is required in order to comply with the existing land application and discharge legislation in the European Union countries. This may include physicochemical and biological processes, with the latter being more advantageous due to their lower cost. Nitrogen removal is accomplished through the conventional nitrification/denitrification, nitritation/denitritation and the complete autotrophic nitrogen removal process; the latter is accomplished by nitritation coupled with the anoxic ammonium oxidation process. As anaerobic digestion effluents are characterized by low COD/TKN ratio, conventional denitrification/nitrification is not an attractive option; short-cut nitrogen removal processes are more promising. Both suspended and attached growth processes have been employed to treat the anaerobic supernatant. Specifically, the sequencing batch reactor, the membrane bioreactor, the conventional activated sludge and the moving bed biofilm reactor processes have been investigated. Physicochemical phosphorus removal via struvite precipitation has been extensively examined. Enhanced biological phosphorus removal from the anaerobic supernatant can take place through the sequencing anaerobic/aerobic process. More recently, denitrifying phosphorus removal via nitrite or nitrate has been explored. The removal of phosphorus from the anaerobic supernatant of OFMSW is an interesting research topic that has not yet been explored. At the moment, standardization in the design of facilities that treat anaerobic supernatant produced from the treatment of OFMSW is still under development. To move toward this direction, it is first necessary to assess the performance of alternative treatment options. It study concentrates existing data regarding the characteristics of the anaerobic supernatant produced from the treatment of OFMSW and from their co-digestion with other BOW. This provides data documenting the effect of the anaerobic digestion operating conditions on the supernatant quality and critically evaluates alternative options for the post-treatment of the liquid fraction produced from the anaerobic digestion process.

Acclimated green microalgae consortium to treat sewage in an alternative urban WWTP in a coastal area of Central Italy.

This study exposed a microalgal consortium formed by Auxenochlorella protothecoides, Tetradesmus obliquus, and Chlamydomonas reinhardtii to six mixed wastewater media containing different proportions of primary (P) or secondary (S) effluents diluted in centrate (C). Algae could grow at centrate concentrations up to 50 %, showing no significant differences between effluents. After acclimation, microalgae cultivated in 50%P-50%C and 50%S-50%C grew at a rate similar to that of control cultures (0.59-0.66 d-1). These results suggest that the consortium acclimated to both sewage streams by modulating the proportion of the species and their metabolism. Acclimation also altered the photosynthetic activity of wastewater-grown samples compared to the control, probably due to partial photoinhibition, changes in consortium composition, and changes in metabolic activity. No major differences were observed between the two streams with respect to biochemical composition, biomass yield, or bioremediation capacity of the cultivated algae but algae grown in the secondary effluent showed qualitatively higher exopolysaccharides (EPS) production than algae grown in primary. Regarding wastewater remediation, microalgae grown in both WW media showed proficient nutrient removal efficiencies (close to 100 %); however, the final pH value (close to 11) would be controversial if the system were upscaled as it is over the legal limit and would cause phosphorus precipitation, so that CO2 addition would be required. The theoretical scale-up of the microalgae system could achieve water treatment costs of 0.109 €·m-3, which was significantly lower than the costs of typical activated sludge systems.

Techno-economic assessment of biorefinery scenarios based on mollusc and fish residuals.

Biorefineries aim to maximise resource recovery from organic sources that have been traditionally considered wastes. In this respect, leftovers from mollusc and seafood processing industries can be a source of multiple bioproducts such as protein hydrolysates (PH), calcium carbonate and co-composted biochar (COMBI). This study aims to evaluate different scenarios of biorefineries fed by mollusc (MW) and fish wastes (FW) to understand which is the most convenient to maximise their profitability. Results showed that the FW-based biorefinery obtained the highest revenues with respect to the amounts of waste treated, i.e., 955.1 €·t-1 and payback period (2.9 years). However, including MW in the biorefinery showed to increase total income as a higher amount of feedstock could be supplied to the system. The profitability of the biorefineries was mainly dependent on the selling price of hydrolysates (considered as 2 €·kg-1 in this study). However, it also entailed the highest operating costs (72.5-83.8% of total OPEX). This highlights the importance of producing high-quality PH in economic and sustainable way to increase the feasibility of the biorefinery.

New parameter for the evaluation of disgnathic patient's surgical planning: a preliminary report.

BACKGROUND: Indications for treatment of patients with maxillo-mandibular malformations have to be researched both in the severity of anatomical alteration affecting the face and psychological outcomes. Indeed, it has been underlined that patients decide to undergo orthodontic and orthognathic procedure mainly for aesthetical issues. Moreover the early combined functional and surgical treatment improves relationship skills in young adults. Dealing with these "aesthetic" features pre surgical planning presents some additional challenges. Even if orthognatic surgery aims to the correct repositioning of skeletal bases but we must achieve complete patient satisfaction. AIM: The Authors present a new parameter to be considered in the planning of patients who undergo orthognatic procedure being the restitution of the face the patient would have had without any pathologic mechanism with respect of the aesthetic features of the family. MATERIALS AND METHODS: Authors identified a series of parameters discussed by Arnett et al and performed a clinical and photographic evaluation of these parameters, in latero-lateral view, directly on the relatives of the patients. A cephalometric analysis, was performed and a series of parameters has been taken into account. CONCLUSIONS: It is very difficult to standardize universal parameters acceptable and applicable for every single case, considering that patient's awareness of the anatomical defect and post-surgical satisfaction don't relate to the correct cephalometric evaluation and the real aesthetic outcomes.

An overview of operations and processes for circular management of dredged sediments.

Dredging is an essential technique to maintain proper water depths in ports and bays. Many dredged sediments are considered as toxic waste due to their significant amounts of metals and other pollutants. In consequence, they need to be treated to reduce this toxicity and avoid pollutant resuspensions. Physical operations and chemical, thermal and biological processes have been conventionally used to this aim, but the traditional linear sediment approach is often unsustainable and economically and environmentally demanding. Considering the increasing people's awareness in environmental issues, more efficient dredged sediment management schemes are required. Some authors are making significant efforts to improve circularity in sediment management processes by taking advantage of the mineral composition of sediments to obtain products for the building and road construction sectors, therefore decreasing the need of raw materials while reducing the amounts of sediments wasted to landfills. However, information related to the characteristics of these products, their mechanical behaviour and their functionality is still scarce, being sediment-based by-products developed mainly at low Technological Readiness Level (TRL), showing low global impact in the market. To implement circular economy in the dredged sediment sector, some technical and socio-political barriers must be still overcome. To this aim, further research and technological applications must be developed, with the support of decision makers and stakeholders. This review aims at giving an overview of the circular trends applied to toxic dredged sediment management, pointing at current opportunities, barriers and constraints that hinder its wide development.

Two-phase thermophilic anaerobic digestion process for biohythane production treating biowaste: preliminary results.

This paper deals with the optimization of a two-phase anaerobic process treating biowaste for hydrogen and methane production. Neither physical nor chemical pre-treatments were used to optimize the process. The work was carried out at pilot scale, using two CSTRs (200 and 380 L working volume respectively) both maintained at thermophilic temperature (55 C) and fed semi-continuously with biowaste. The experiment was divided into three periods; during the first two periods the organic loading rate was maintained at 20 kg TVS/m3 d and the hydraulic retention time was changed from 6.6 to 3.3 days, while in the last period the digestate of the second reactor was recirculated to the first reactor in order to buffer the system and control pH at levels around 5. The HRT was maintained at 3.3 days and the OLR was decreased at 16.5 kg TVS/m3 d. The best yield was obtained in the last period where a specific hydrogen production of 50.9 L/kg VSfed was reached, with a H2 content in biogas from the first reactor of 36%. The methanogenic stage after the hydrogen conversion reached a specific biogas production of 0.62 m3/kg VSfed and an overall organic removal above 70%, without any stability problem. The overall biogas production was some 1.5 m3 per day with a gas composition of 10% H2 and 50% CH4.

Effects of different pre-treatments on the properties of polyhydroxyalkanoates extracted from sidestreams of a municipal wastewater treatment plant.

The paper deals with effects of two different widespread extraction methods (conventional extraction and Soxhlet extraction) and four different pre-treatments (homogenization with pressure and with blades, sonication, and impact with glass spheres) on the extraction yields and properties of polyhydroxyalkanoate (PHA) extracted from biomass coming from an innovative process (short-cut enhanced phosphorus and PHA recovery) applied in a real wastewater treatment plant. The results show that the two different extraction processes affected the crystallization degree and the chemical composition of the polymer. On the other hand, the extractive yield was highly influenced by pre-treatments: homogenization provided a 15% more extractive yield than the others. Homogenization, especially at high pressure, proved to be the best pre-treatment also in terms of the purity, visual appearance (transparency and clearness), thermal stability, and mechanical performances of the obtained PHA films. All the PHA films begin to melt long before their degradation temperature (Td > 200 °C): this allows their use in the fields of extrusion or compression moulding. SYNOPSIS: Optimizing the extraction of PHAs from municipal wastewater gives a double beneficial environmental impact: wastewater treatment and circular bio-based carbon upgrade to biopolymers for the production of bioplastics and other intersectoral applications.

Proposal for a new self-compiled questionnaire in patients affected by temporo-mandibular joint disorders (TMD).

In this work, we propose a self-compiled questionnaire, for those patients showing dysfunctions of the temporomandibular joint. The questionnaire, composed by 33 closed multiple-choice questions, represents one of the steps in the diagnostic procedure, together with the clinical notes compiled by the medical specialist and with the other necessary diagnostic researches. It also has the purpose to make easier anamnesis and clinic procedure and gathering of all informations useful for a right clinical diagnosis, and so for an appropriate therapy.

Application of a membrane bioreactor for winery wastewater treatment.

Winery wastewaters are variable in nature and are hard to treat by means of the conventional activated sludge process because of the high organic loading associated with their production, especially during vintage. To face this situation, recently, membrane bioreactors have been widely applied to treat winery wastewaters. In this study, a full-scale membrane bioreactor treated some 110 m(3)/d of wastewater and organic loadings up to 1,600 kg COD per day. The average removal efficiency was 95% while the corresponding sludge yield was only 0.1 kg MLVSS per kg COD removed, as usual for these wastewaters. A detailed analysis of energy consumption showed specific energy demands of 2.0-3.6 kWh/m(3) of treated wastewater or 1 kWh per kg of COD removed.

A knowledge discovery framework to predict the N2O emissions in the wastewater sector.

Data Analytics is being deployed to predict the dissolved nitrous oxide (N2O) concentration in a full-scale sidestream sequence batch reactor (SBR) treating the anaerobic supernatant. On average, the N2O emissions are equal to 7.6% of the NH4-N load and can contribute up to 97% to the operational carbon footprint of the studied nitritation-denitritation and via-nitrite enhanced biological phosphorus removal process (SCENA). The analysis showed that average aerobic dissolved N2O concentration could significantly vary under similar influent loads, dissolved oxygen (DO), pH and removal efficiencies. A combination of density-based clustering, support vector machine (SVM), and support vector regression (SVR) models were deployed to estimate the dissolved N2O concentration and behaviour in the different phases of the SBR system. The results of the study reveal that the aerobic dissolved N2O concentration is correlated with the drop of average aerobic conductivity rate (spearman correlation coefficient equal to 0.7), the DO (spearman correlation coefficient equal to -0.7) and the changes of conductivity between sequential cycles. Additionally, operational conditions resulting in low aerobic N2O accumulation (<0.6 mg/L) were identified; step-feeding, control of initial NH4+ concentrations and aeration duration can mitigate the N2O peaks observed in the system. The N2O emissions during aeration shows correlation with the stripping of accumulated N2O from the previous anoxic cycle. The analysis shows that N2O is always consumed after the depletion of NO2- during denitritation (after the "nitrite knee"). Based on these findings SVM classifiers were constructed to predict whether dissolved N2O will be consumed during the anoxic and anaerobic phases and SVR models were trained to predict the N2O concentration at the end of the anaerobic phase and the average dissolved N2O concentration during aeration. The proposed approach accurately predicts the N2O emissions as a latent parameter from other low-cost sensors that are traditionally deployed in biological batch processes.

A decade of nitrous oxide (N2O) monitoring in full-scale wastewater treatment processes: A critical review.

Direct nitrous oxide (N2O) emissions during the biological nitrogen removal (BNR) processes can significantly increase the carbon footprint of wastewater treatment plant (WWTP) operations. Recent onsite measurement of N2O emissions at WWTPs have been used as an alternative to the controversial theoretical methods for the N2O calculation. The full-scale N2O monitoring campaigns help to expand our knowledge on the N2O production pathways and the triggering operational conditions of processes. The accurate N2O monitoring could help to find better process control solutions to mitigate N2O emissions of wastewater treatment systems. However, quantifying the emissions and understanding the long-term behaviour of N2O fluxes in WWTPs remains challenging and costly. A review of the recent full-scale N2O monitoring campaigns is conducted. The analysis covers the quantification and mitigation of emissions for different process groups, focusing on techniques that have been applied for the identification of dominant N2O pathways and triggering operational conditions, techniques using operational data and N2O data to identify mitigation measures and mechanistic modelling. The analysis of various studies showed that there are still difficulties in the comparison of N2O emissions and the development of emission factor (EF) databases; the N2O fluxes reported in literature vary significantly even among groups of similar processes. The results indicated that the duration of the monitoring campaigns can impact the EF range. Most N2O monitoring campaigns lasting less than one month, have reported N2O EFs less than 0.3% of the N-load, whereas studies lasting over a year have a median EF equal to 1.7% of the N-load. The findings of the current study indicate that complex feature extraction and multivariate data mining methods can efficiently convert wastewater operational and N2O data into information, determine complex relationships within the available datasets and boost the long-term understanding of the N2O fluxes behaviour. The acquisition of reliable full-scale N2O monitoring data is significant for the calibration and validation of the mechanistic models -describing the N2O emission generation in WWTPs. They can be combined with the multivariate tools to further enhance the interpretation of the complicated full-scale N2O emission patterns. Finally, a gap between the identification of effective N2O mitigation strategies and their actual implementation within the monitoring and control of WWTPs has been identified. This study concludes that there is a further need for i) long-term N2O monitoring studies, ii) development of data-driven methodological approaches for the analysis of WWTP operational and N2O data, and iii) better understanding of the trade-offs among N2O emissions, energy consumption and system performance to support the optimization of the WWTPs operation.

Anatomic relationship between trigeminal nerve and temporomandibular joint.

Temporomandibular joint disorders (TMD) is a collective term used to describe pathologic conditions involving temporomandibular joint (TMJ), masticatory muscles and associated structures. Common related complaints include local pain, limited mouth opening and TMJ noises whereas symptoms often associated to TMD with debated pathogenesis enclose earache, headaches, tinnitus and trigeminal-like symptoms such as atypical orofacial pain. In particular, TMD trigeminal associated symptoms are intricate, difficult to treat and exert a great impact on everyday life of the patients thus invoking a complex multidisciplinary treatment. In this paper, the authors analyze the anatomic and topographic relationships between the mandibular branch of the trigeminal nerve and the medial aspect of the TMJ capsule in 8 fresh adult cadavers thus resuming a pathologic relationship between atypical trigeminal symptoms and TMD.

Exploring the potential of membrane bioreactors to enhance metals removal from wastewater: pilot experiences.

The potential of membrane bioreactors to enhance the removal of selected metals from low loaded sewages has been explored. A 1400 litre pilot plant, equipped with an industrial submerged module of hollow fibre membranes, has been used in three different configurations: membrane bioreactor, operating in sequencing batch modality, for the treatment of real mixed municipal/industrial wastewater; membrane-assisted biosorption reactor, for the treatment of real leachate from municipal landfills; continuously fed membrane bioreactor, for the treatment of water charged with cadmium and nickel ions. The results show that: (a) in treating wastewaters with low levels of heavy metals (< one milligram per litre concentration), operating high sludge ages is not an effective strategy to significantly enhance the metals removal; (b) Hg and Cd are effectively removed already in conventional systems with gravitational final clarifiers, while Cu, Cr, Ni can rely on a additional performance in membrane bioreactors; (c) the further membrane effect is remarkable for Cu and Cr, while it is less significant for Ni. Basically, similar membrane effects recur in three different experimental applications that let us estimate the potential of membrane system to retain selected metal complexes. The future development of the research will investigate the relations between the membrane effect and the manipulable filtration parameters (i.e., permeate flux, solids content, filtration cycle).

Occurrence and fate of heavy metals in large wastewater treatment plants treating municipal and industrial wastewaters.

This paper deals with a detailed study on the occurrence and fate of heavy metals (plus As, Fe and Al) in five Italian large wastewater treatment plants treating municipal and industrial wastewaters. The study showed that some of the compounds (As, Hg and Cd) were present at trace levels, while others were dispersed in a broad range of concentrations and were sometimes under the detection limit. The occurrence followed the order Hg = As < Hg < Pb < Ni < Cu < Cr < Fe < Zn < Al. Metals were mainly present bound to particulate organic matter in municipal wastewaters while they were often present in soluble phase in industrial wastewaters. Some heavy metals, like Hg and Pb, showed clear correlations with Al and Fe, therefore the last could be used as control parameters. Metals were removed with good efficiency in the treatment works, with the order As < Cd = Cr = Zn < Pb < Hg < Ni = Al < Cu < Fe. Metals then concentrated in waste activated sludge and accumulated after sludge stabilisation because of volatile solids degradation, therefore some problems may arise with limit for agricultural application, in particular for Hg, Cd and Ni.

Process control automation and remote on-line supervision: the strategy for wastewater treatment in an Italian piedmont.

The paper deals with the real application of a strategy, based on process control automation and remote on-line supervision, for the wastewater treatment in a piedmont. Seven existing small wastewater treatment plants were selected to be upgraded and to be included into a network remotely supervised. A consolidated bending point based alternating process was applied for the biological treatment. Further, the potentialities of the process control automation were enhanced by the appropriate design of the whole plant. The examination of a case study included into the network shows the real stable high performances of the plant in terms of total nitrogen removal. Moreover, the power requirements are significantly reduced according to a correct energy policy.

Pilot-scale multi-stage reverse osmosis (DT-RO) for water recovery from landfill leachate.

Recovery of high quality water from municipal landfill leachate was studied by three-stage disc tube reverse osmosis optimized in pilot-scale. Following UF-membrane-assisted activated sludge plant, overall 46.5 tons of leachate were post-treated in real environment and analyzed for conventional contaminants and hazardous compounds (e.g. heavy metals, boron, selenium) throughout operation of membrane system. Operating pressure ranged from 21 to 76 bar, while permeate flux varied in the range 7.1-32.5 L m-2 h-1. Rejection factors of specific ions were related to the pressure and global removals were assessed for each stage (e.g. E%COD = 92.4-99.2%, E%NH4 = 46.2-95.8%, E%NOx = 84.8-97.9%; E%TDS = 88-95.5%). Boron removal was assessed in the range 34-48%, so as to require the third stage to reach standard for discharge or reuse. Two stages were sufficient to reach water recovery higher than 91%. Long-term operation and mathematical modeling demonstrated how the Δπ/ΔP ratio can support the decisions for membrane cleaning and predictive maintenance: permeability decline was associated to the ratio increase from 0.72 to 0.73 to 1.13-1.21.