Modifying the Properties of Microemulsion Droplets by Addition of Thermoresponsive BAB* Copolymers.

Oil-in-water (O/W) microemulsions (ME) typically feature a low viscosity and exhibit ordinary viscosity reduction as a function of temperature. However, for certain applications, avoiding or even reverting the temperature trend might be required. This can be conceived by adding thermoresponsive (TR) block copolymers that induce network formation as the temperature increases. Accordingly, various ME-polymer mixtures were studied for which three different block copolymer architectures of BAB*-, B2AB*-, and B(AB*)2-types were employed. Here, "B" represents a permanently hydrophobic, "A" a permanently hydrophilic, and "B*" a TR block. For the TR-block, three different poly(acrylamide)s, namely poly(N-n-propylacrylamide) (pNPAm), poly(N,N-diethylacrylamide) (pDEAm), and poly(N-isopropylacrylamide) (pNiPAm), were used, which all exhibit a lower critical solution temperature. For a well-selected ME concentration, these block copolymers lead to a viscosity enhancement with increasing temperature. At a polymer concentration of about 22 g L-1, the most pronounced enhancement was observed for the pNPAm-based systems with factors up to 3, 5, and 8 for BAB*, B2AB*, and B(AB*)2, respectively. This phenomenon is caused by the formation of a transitory network mediated by TR-blocks, as evidenced by the direct correlation between the attraction strength and the viscosity enhancement. For applications requiring a high hydrophobic payload, which is attained via ME droplets, this kind of tailored temperature-dependent viscosity control of surfactant systems should therefore be advantageous.

Thermoresponsive Self-Assembly of Twofold Fluorescently Labeled Block Copolymers in Aqueous Solution and Microemulsions.

A nonionic double hydrophilic block copolymer with a long permanently hydrophilic and a small thermoresponsive block is synthesized by reversible addition-fragmentation chain-transfer polymerization (RAFT). By employing a specifically designed chain-transfer agent, the polymer is functionalized with complementary end groups which are suited for Förster resonance energy transfer (FRET). The end group attached to the permanently hydrophilic block of poly(N,N-dimethylacrylamide) pDMAm is designed as a permanently hydrophobic segment ("sticker") comprising a long alkyl chain and the 4-aminonaphthalimide fluorophore. The other end attached to the thermoresponsive block of poly(N-isopropylacrylamide) pNiPAm incorporates a coumarin fluorophore. The temperature-dependent self-assembly of the twofold fluorescently labeled copolymer is studied in pure aqueous solution as well as in an o/w microemulsion by several techniques including turbidimetry, dynamic light scattering (DLS), and fluorescence spectroscopy. It is compared to the behaviors of the analogous twofold-labeled pDMAm and pNiPAm homopolymer references. The findings indicate that the block copolymer behaves as a polymeric surfactant at low temperatures, with one relatively small hydrophobic end block and an extended hydrophilic chain forming "hairy micelles". At elevated temperatures above the LCST phase transition of the pNiPAm block, however, the copolymer behaves as an associative telechelic polymer with two nonsymmetrical hydrophobic end blocks, which do not mix. Thus, instead of a network of bridged "flower micelles", large dynamic aggregates are formed. These are connected alternatingly by the original micellar cores as well as by clusters of the collapsed pNiPAm blocks. This type of structure is even more favored in the o/w microemulsion than in pure aqueous solution, as the microemulsion droplets constitute an attractive anchoring point for the hydrophobic dodecyl sticker but not for the collapsed pNiPAm chains.

On the Limits of Benzophenone as Cross-Linker for Surface-Attached Polymer Hydrogels.

The synthesis of different photo-reactive poly(alkenyl norbornenes) and poly(oxonorbornenes) containing benzophenone (BP) via ring-opening metatheses polymerization (ROMP) is described. These polymers are UV irradiated to form well-defined surface-attached polymer networks and hydrogels. The relative propensity of the polymers to cross-link is evaluated by studying their gel content and its dependency on BP content, irradiation wavelength (254 or 365 nm) and energy dose applied (up to 11 J·cm-²). Analysis of the UV spectra of the polymer networks demonstrates that the poly(oxonorbornenes) show the expected BP-induced crosslinking behavior at 365 nm, although high irradiation energy doses and BP content are needed. However, these polymers undergo chain scission at 254 nm. The poly(alkenyl norbornenes), on the other hand, do not cross-link at 365 nm, whereas moderate to good cross-linking is observed at 254 nm. UV spectra demonstrate that the cross-linking at 254 nm is due to BP cross-linking combined with a [2 + 2] cylcoaddition of the alkenyl double bonds. This indicates limitations of benzophenone as a universally applicable cross-linking for polymer networks and hydrogels.