RESUMEN
Fluorinated ethers have become promising electrolyte solvent candidates for lithium metal batteries (LMBs) because they are endowed with high oxidative stability and high Coulombic efficiencies of lithium metal stripping/plating. Up to now, most reported fluorinated ether electrolytes are -CF3-based, and the influence of ion solvation in modifying degree of fluorination has not been well-elucidated. In this work, we synthesize a hexacyclic coordinated ether (1-methoxy-3-ethoxypropane, EMP) and its fluorinated ether counterparts with -CH2F (F1EMP), -CHF2 (F2EMP), or -CF3 (F3EMP) as terminal group. With lithium bis(fluorosulfonyl)imide as single salt, the solvation structure, Li-ion transport behavior, lithium deposition kinetics, and high-voltage stability of the electrolytes were systematically studied. Theoretical calculations and spectra reveal the gradually reduced solvating power from nonfluorinated EMP to fully fluorinated F3EMP, which leads to decreased ionic conductivity. In contrast, the weakly solvating fluorinated ethers possess higher Li+ transference number and exchange current density. Overall, partially fluorinated -CHF2 is demonstrated as the desired group. Further full cell testing using high-voltage (4.4 V) and high-loading (3.885 mAh cm-2) LiNi0.8Co0.1Mn0.1O2 cathode demonstrates that F2EMP electrolyte enables 80% capacity retention after 168 cycles under limited Li (50 µm) and lean electrolyte (5 mL Ah-1) conditions and 129 cycles under extremely lean electrolyte (1.8 mL Ah-1) and the anode-free conditions. This work deepens the fundamental understanding on the ion transport and interphase dynamics under various degrees of fluorination and provides a feasible approach toward the design of fluorinated ether electrolytes for practical high-voltage LMBs.
RESUMEN
The development of cutting-edge solid-state electrolytes (SSEs) entails a deep understanding of the underlying correlation between the structure and ionic conductivity. Generally, the structure of SSEs encompasses several interconnected crystal parameters, and their collective influence on Li+ transport can be challenging to discern. Here, we systematically investigate the structure-function relationship of halide spinel LixMgCl2+x (2 ≥ x ≥ 1) SSEs. A nonmonotonic trend in the ionic conductivity of LixMgCl2+x SSEs has been observed, with the maximum value of 8.69 × 10-6 S cm-1 achieved at x = 1.4. The Rietveld refinement analysis, based on neutron diffraction data, has revealed that the crystal parameters including cell parameters, Li+ vacancies, Debye-Waller factor, and Li-Cl bond length assume diverse roles in influencing ionic conductivity of LixMgCl2+x at different stages within the range of x values. Besides, mechanistic analysis demonstrates Li+ transport along three-dimensional pathways, which primarily governs the contribution to ionic conductivity of LixMgCl2+x SSEs. This study has shed light on the collective influence of crystal parameters on Li+ transport behaviors, providing valuable insights into the intricate relationship between the structure and ionic conductivity of SSEs.
RESUMEN
With high degree of metamorphism and carbon content, anthracite is commonly used for activated carbon. The structural properties of anthracite play a decisive role in its materialization, while with chemical oxidation, anthracite structure can be purposefully improved. The anthracite oxide was prepared via acid leaching and oxidizing, using high carbon content and low ash content anthracite from Zhaotong, Yunnan Province, China. The structural and spectroscopy characteristics of anthracite and anthracite oxide were acquired with X-ray diffraction (XRD), Raman spectroscopy and attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR). The results show that crystallites in anthracite have intermediate structures between graphite and amorphous. Compared with bitumite and lignite, its structure order degree lies between graphite and low metamorphic coals with relatively high average diameter of coal crystallites(La) and average height of coal crystallites (Lc). The process of anthracite oxidation can be modeled in two steps, the edge of crystal was curled and destroyed with strong oxidation, with the generation of CO group and intercalation of HNO3/H2SO4 into the edge layers, leading to the reducing of lateral sizes; HNO3/H2SO4 were continually intercalated into crystals, resulted in the increase of interlayer spacing (d(002)) from 0.351 to 0.361 nm, and the number of stacked layers dropped to 4.5 from 6 due to exfoliate. ID1/IG in Raman spectroscopy increased from 1.9 to 2.0, with full width at half maximum (FWHM) of G bond and intensity of D2 bond increasing from 63 to 68 and 10.26 to 13.78. Numbers of new CO, CO, NO2 groups generated, leading to the decrease of oxygen-containing functional groups content from 0.11 to 0.42. After HNO3/H2SO4 oxidation, the aromaticity (fa) of anthracite oxide increases, with the decrease of structure order degree and more-over a lot of active reaction sites generates in the process. The oxidation of anthracite enables anthracite has great potential in the application of porous carbon preparation.
RESUMEN
Lithium batteries have been essential technologies and become an integral part of our daily lives, powering a range of devices from phones to electric vehicles. To fully understand and optimize the performance of lithium batteries, it is necessary to investigate their internal states and processes through various characterization methods. Neutron imaging has been an indispensable complementary characterization technique to X-ray imaging or electron microscopy because of the unique interaction principle between neutrons and matter. It provides particular insights into the various states of matter inside lithium batteries, including the Li+ concentration in solid electrodes, the Li plating/stripping behavior of Li-metal anodes, the Li+ diffusion in solid ionic conductors, the distribution of liquid electrolytes and the generation of gases. This review aims to highlight the capabilities and advantages of neutron imaging in characterizing lithium batteries, as well as its current state of application in this field. Additionally, we discuss the potential of neutron imaging to contribute to the ongoing development of advanced batteries through its ability to visualize internal evolution.
RESUMEN
Solid-state electrolytes with high ionic conductivities are crucial for the development of all-solid-state lithium batteries, and there is a strong correlation between the ionic conductivities and underlying lattice structures of solid-state electrolytes. Here, we report a lattice manipulation method of replacing [Li2OH]+ clusters with potassium ions in antiperovskite solid-state electrolyte (Li2OH)0.99K0.01Cl, which leads to a remarkable increase in ionic conductivity (4.5 × 10â3 mS cmâ1, 25 °C). Mechanistic analysis indicates that the lattice manipulation method leads to the stabilization of the cubic phase and lattice contraction for the antiperovskite, and causes significant changes in Li-ion transport trajectories and migration barriers. Also, the Li||LiFePO4 all-solid-state battery (excess Li and loading of 1.78 mg cmâ2 for LiFePO4) employing (Li2OH)0.99K0.01Cl electrolyte delivers a specific capacity of 116.4 mAh gâ1 at the 150th cycle with a capacity retention of 96.1% at 80 mA gâ1 and 120 °C, which indicates potential application prospects of antiperovskite electrolyte in all-solid-state lithium batteries.