In vitro sun protection factor: still a challenge with no final answer.

In the past, several attempts have been made to develop in vitro methods for determining protection against UV radiation. To date however, there is no broadly accepted method. Various known and unknown parameters influence the transmission measurements of scattering films, such as the multifaceted compositions of sunscreens, the technical limitations of measurement devices as well as the difficulty to apply very thin films of sunscreen in a reproducible manner throughout different laboratories. In vitro data were measured in this multicenter study to compare possible methodologies and strategies for an in vitro approach to the sun protection factor (SPF). This publication will not present a final in vitro SPF test method, but it will point out which technical side effects may influence such a method. Influential factors such as the quality of spectrophotometer used, the amount of product applied, pretreatment of samples, time and temperature of equilibration, size of the measured surface, the application process or the calculation on the basis of standardized data are presented and discussed. Finally, a reduction of the standard deviations within single laboratories could be realized for in vitro SPF testing, but no improvement of the interlaboratory comparison was obtained. The development of a valid and reliable SPF in vitro test still remains a challenge, and further work is necessary to develop a satisfactory method.

In vitro testing to assess the UVA protection performance of sun care products.

The UVA protection delivered by sunscreens is an issue of increasing importance due to the increasing knowledge about UVA-induced skin damage. In Europe there is no officially accepted method available to determine the degree of UVA protection. Therefore, the objective of the present study was to design a protocol combining the merits of an in vitro model, which are simple and reproducible, with aspects known to be relevant from in vivo studies. The principle is: an UV-transparent support to which the test product is applied, a (pre)irradiation and a transmission measurement. Transpore(R) tape (standard support for SPF determinations) was found to be incompatible with many preparations on prolonged contact times. Roughened quartz was adopted as a suitable alternative. Transmission measurements on this support are not reliable with a layer of 2 mg cm(-2) (standard for SPF) due to detection limitations of spectrophotometers, hence a reduced layer of 0.75 mg cm(-2) was adopted. Overall, it is very difficult to apply products in a reproducible thin layer on appropriate substrates. As a consequence, absolute parameters derived from the transmission profile show relatively large dispersion, whereas relative parameters, such as critical wavelength lambda(c)[1] or UVA/UVB ratio are much less sensitive to unavoidable variations in layer thickness. An increase in deviations was observed when the samples were irradiated before measurement. It is crucial to control the output carefully (spectral distribution and even more importantly, irradiance and dose delivered) of the light source. By doing so and also taking into account the previous learning steps, a protocol was drafted and tested in a ringtest (four samples in six laboratories). The results are encouraging and show that if relative parameters (e.g. lambda(c), UVA/UVB ratio) are considered, the intra- as well as interlaboratory reproducibility is clearly better than can be obtained in vivo. In general, we describe a suitable method, which can be considered in any future official discussions about the methodology to determine UVA protection.

Influence of applied quantity of sunscreen products on the sun protection factor--a multicenter study organized by the DGK Task Force Sun Protection.

It is often debated that the protection against solar-induced erythema under real conditions is dependent upon the amount of sunscreen applied. It is believed that when too little is applied a lower sun protection than indicated on the label will result. The aim of this study was to quantify this effect. In this multicenter study, the influence of three different amounts (0.5, 1.0, 2.0 mg/cm(2)) of three commercial sunscreen products in three reliable test centers was investigated according to the test protocol of The International Sun Protection Factor Test Method. The main result was a linear dependence of the SPF on the quantity applied. Taking into consideration the volunteer-specific variations, an exponential dependence of confidence interval of the in vivo SPF and amount applied was found. The highest amount applied (2.0 mg/cm(2)) was linked to the lowest confidence intervals. Thus, from the point of view of producing reliable and reproducible in vivo results under laboratory conditions, the recommendation of this multicenter study is an application quantity of 2.0 mg/cm(2).