Comparative Static and Dynamic Analyses of Solvents for Removal of Asphaltene and Wax Deposits above- and below-Surface at an Iranian Carbonate Oil Field.

During production from oil wells, the deposition of asphaltene and wax at surface facilities and porous media is one of the major operational challenges. The crude oil production rate is significantly reduced due to asphaltene deposition inside the reservoir. In addition, the deposition of these solids inside the surface facilities is costly to oil companies. In this study, the efficiency of different solvents in dissolving asphaltene and wax was investigated through static and dynamic tests. The analysis of solid deposits from the surface choke of one of the Iranian carbonate oil fields showed that they consisted of 41.3 wt % asphaltene, and the balance was predominantly wax. In addition, the asphaltenes obtained from the surface choke solid deposits had a more complex structure than that of asphaltenes extracted from the crude oil itself. The static tests showed that xylene, toluene, gasoline, kerosene, and gas condensate had the highest efficiencies in dissolving solid deposits; conversely, diesel had a negative impact on dissolving solid deposits. Static tests on pure asphaltene showed that, among the tested solvents, gas condensate and diesel had a negative effect on the solubility of asphaltene. The dynamic core flooding results showed that asphaltene deposition inside the cores reduced the permeability by 79-91%. Among the tested solvents, xylene, gasoline, and kerosene resulted in the highest efficacy in restoring the damaged permeability, and higher efficiency was obtained with an equivalent solvent injection rate of 1 bbl/min versus 3 bbl/min.

Application of a Novel Green Nano Polymer for Chemical EOR Purposes in Sandstone Reservoirs: Synergetic Effects of Different Fluid/Fluid and Rock/Fluid Interacting Mechanisms.

In this research, a novel natural-based polymer, the Aloe Vera biopolymer, is used to improve the mobility of the injected water. Unlike most synthetic chemical polymers used for chemical-enhanced oil recovery, the Aloe Vera biopolymer is environmentally friendly, thermally stable in reservoir conditions, and compatible with reservoir rock and fluids. In addition, the efficiency of the Aloe Vera biopolymer was investigated in the presence of a new synthetic nanocomposite composed of KCl-SiO2-xanthan. This chemically enhanced oil recovery method was applied on a sandstone reservoir in Southwest Iran with crude oil with an API gravity of 22°. The Aloe Vera biopolymer's physicochemical characteristics were initially examined using different analytical instruments. The results showed that the Aloe Vera biopolymer is thermally stable under reservoir conditions. In addition, no precipitation occurred with the formation brine at the salinity of 80,000 ppm. The experimental results showed that adding ethanol with a 10% volume percentage reduced interfacial tension to 15.3 mN/m and contact angle to 108°, which was 52.33 and 55.56% of these values, respectively. On the other hand, adding nanocomposite lowered interfacial tension and contact angle values to 4 mN/m and 48°, corresponding to reducing these values by 87.53 and 71.42%, respectively. The rheology results showed that the solutions prepared by Aloe Vera biopolymer, ethanol, and nanocomposite were Newtonian and fitted to the Herschel-Bulkley model. Finally, core flooding results showed that the application of a solution prepared by Aloe Vera biopolymer, ethanol, and nanocomposite was effective in increasing the oil recovery factor, where the maximum oil recovery factor of 73.35% was achieved, which could be attributed to the IFT reduction, wettability alteration, and mobility improvement mechanisms.

Effects of MgO, γ-Al2O3, and TiO2 Nanoparticles at Low Concentrations on Interfacial Tension (IFT), Rock Wettability, and Oil Recovery by Spontaneous Imbibition in the Process of Smart Nanofluid Injection into Carbonate Reservoirs.

Recently, some nanoparticles have been used to upgrade injected water into oil reservoirs to enhance oil recovery. These nanoadditives can be used in a variety of injectable waters, including smart/engineered water with special salinities. In this study, the performance of smart water containing different concentrations of magnesium sulfate (MgSO4) and calcium chloride (CaCl2) and 500 ppm of titanium dioxide (TiO2), γ-alumina (γ-Al2O3), and magnesium oxide (MgO) nanoparticles in interfacial tension (IFT) and contact angle reduction and oil production under imbibition of the chemical fluids was investigated. Based on the results, the IFT decreased more when ions and nanoparticles were present in the system. An optimum IFT of 4.684 mN/m was recorded for the nanofluid containing 2000 ppm of MgSO4 + 500 ppm of MgO. The results of contact angle tests demonstrated improved saline water capabilities in the presence of nanoparticles and showed that a very effective reduction was accessible and highly hydrophilic wettability was obtained when using smart water with stable nanoparticles as a minimum contact angle of 18.33° was obtained by the optimal fluid containing nano-γ-Al2O3. Finally, an ultimate oil production of 64.1-68.7% was obtained in six experiments with smart water and stable nanoparticles.

Experimental Investigation of Foam Flooding Using Anionic and Nonionic Surfactants: A Screening Scenario to Assess the Effects of Salinity and pH on Foam Stability and Foam Height.

Gravity override and viscous fingering are inevitable in gas flooding for improving hydrocarbon production from petroleum reservoirs. Foam is used to regulate gas mobility and consequently improve sweep efficiency. In the enhanced oil recovery process, when the foam is introduced into the reservoir and exposed to the initial saline water saturation and pH condition, selection of the stable foam is crucial. Salinity and pH tolerance of generated foams are a unique concern in high salinity and pH variable reservoirs. NaOH and HCl are used for adjusting the pH, and NaCl and CaCl2 are utilized to change salinity. Through analyzing these two factors along with surfactant concentration, we have instituted a screening scenario to optimize the effects of salinity, pH, surfactant type, and concentration to generate the most stable state of the generated foams. An anionic (sodium dodecyl sulfate) and a nonionic (lauric alcohol ethoxylate-7) surfactants were utilized to investigate the effects of the surfactant type. The results were applied in a 40 cm synthetic porous media fully saturated with distilled water to illustrate their effects on water recovery at ambient conditions. This most stable foam along with eight different stabilities and foamabilities and air alone was injected into the sand pack. The results show that in optimum surfactant concentration, the stability of LA-7 was not highly changed with salinity alteration. Also, we probed that serious effects on foam stability are due to divalent salt and CaCl2. Finally, we found the most water recovery that was obtained by the three most stable foams by the formula of 1 cmc SDS + 0.5 M NaCl, 1 cmc SDS + 0.01 M CaCl2, and LA-7@ pH ∼ 6 from porous media flooding. Total water recovery for the most stable foam increased by an amount of 65% compared to the state of air alone. A good correlation between foam stability and foamability at higher foam stabilities was observed.

Development of a Nanobiodegradable Drilling Fluid Using Prosopis farcta Plant and Pomegranate Peel Powders with Metal Oxide Nanoparticles.

One of the inevitable problems encountered during the petroleum well drilling process is "lost circulation" in which part of the drilling fluid is lost into the formation. A combination of nanoparticles with their unique properties and cost-effective biodegradable materials can play an effective role in treating fluid loss. In this study, our aim was to formulate drilling fluids modified with nanoparticles, pomegranate peel powder, and Prosopis farcta plant powder. The drilling fluids were identified and recognized using scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy techniques. Furthermore, experimental tests were conducted in order to investigate the performance of the newly formulated drilling fluid in improving fluid loss characteristics. The obtaining results have shown that adding 0.3 wt % of pomegranate peel powder to the reference (base) drilling fluid reduces the filter loss volume to 7.9 mL compared to the reference fluid (11.6 mL). As the optimal concentration of TiO2 was mixed with 0.3 wt % of pomegranate peel powder then added to the reference fluid, the filter loss volume was reduced to 8.6 mL.

Synthesis, Characterization, and Assessment of a CeO2@Nanoclay Nanocomposite for Enhanced Oil Recovery.

In this paper, synthesis and characterization of a novel CeO2/nanoclay nanocomposite (NC) and its effects on IFT reduction and wettability alteration is reported in the literature for the first time. The NC was characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), energy-dispersive X-ray spectroscopy (EDS), and EDS MAP. The surface morphology, crystalline phases, and functional groups of the novel NC were investigated. Nanofluids with different concentrations of 100, 250, 500, 1000, 1500, and 2000 ppm were prepared and used as dispersants in porous media. The stability, pH, conductivity, IFT, and wettability alternation characteristics of the prepared nanofluids were examined to find out the optimum concentration for the selected carbonate and sandstone reservoir rocks. Conductivity and zeta potential measurements showed that a nanofluid with concentration of 500 ppm can reduce the IFT from 35 mN/m to 17 mN/m (48.5% reduction) and alter the contact angle of the tested carbonate and sandstone reservoir rock samples from 139° to 53° (38% improvement in wettability alteration) and 123° to 90° (27% improvement in wettability alteration), respectively. A cubic fluorite structure was identified for CeO2 using the standard XRD data. FESEM revealed that the surface morphology of the NC has a layer sheet morphology of CeO2/SiO2 nanocomposite and the particle sizes are approximately 20 to 26 nm. TGA analysis results shows that the novel NC has a high stability at 90 °C which is a typical upper bound temperature in petroleum reservoirs. Zeta potential peaks at concentration of 500 ppm which is a sign of stabilty of the nanofluid. The results of this study can be used in design of optimum yet effective EOR schemes for both carbobate and sandstone petroleum reservoirs.