Interactions of particulate- and dissolved-phase heavy metals in a mature stormwater bioretention cell.

Bioretention is an increasingly common stormwater control measure (SCM) for mitigation of stormwater quantity and quality. Studies from lab to field scale have shown successful removal of total metals from stormwater, especially Cu and Zn which are ubiquitous in the urban environment yet detrimental to aquatic ecosystems. While bioretention effectively removes particulate matter and particulate bound (PB) contaminants, removal performance of dissolved metals has been neglected in field studies. After approximately two decades of these systems being implemented, with a typical design-life of 20 years, performance of mature systems is unknown. This study examined the performance of a 16- to 18-year-old bioretention cell by characterizing Cu and Zn partitioning and removal. Flow-weighted composite samples of stormwater and bioretention effluent were collected and analyzed for total and dissolved metals. Size-fractioned road-deposited sediments (RDS) were collected and analyzed for metals and particle size distribution. The comparison of RDS and PB metals showed that PB-Zn was enriched in stormwater, indicating higher mobility of PB-Zn compared to PB-Cu. The mature bioretention system effectively removed particulates and PB-metals with average load reductions of 82% and 83%, respectively. While concentrations for dissolved metals were low (<40 µg/L), no significant difference between influent and effluent was observed. Effluent concentrations of total and dissolved Cu, total organic carbon, and particulates were not significantly different from those measured over 10 years ago at the site, while total Zn effluent concentration slightly increased. MINTEQ speciation modeling showed that Cu was approximately 100% bound with dissolved organic matter (DOM) in all bioretention effluent. While Zn was also mostly bound with DOM in effluent, some events showed free ionic Zn reaching concentrations in the same order of magnitude. Media amendments, maintenance, and monitoring of SCMs should be considered where further removal of dissolved metals is necessary for the protection of aquatic environments.

The stability of Staphylococcal bacteriophage in presence of local vancomycin concentrations used in clinical practice.

PURPOSE: To evaluate the stability of a clinically used Staphylococcal bacteriophage with doses of vancomycin that are encountered with local administration of vancomycin for musculoskeletal infections. METHODS: A Staphylococcal bacteriophage was evaluated for stability in different pH ranges. Then that same bacteriophage was evaluated for stability with different concentrations of vancomycin and with vancomycin biodegradable antibiotic beads. RESULTS: The bacteriophage had stability within a pH range of 4-10. There was a statistically significant (P < 0.05) decrease in the amount of bacteriophage over 24 h for vancomycin concentrations of 10 mg/mL and 100 mg/mL compared to lower vancomycin concentrations (1 mg/mL, 0.1 mg/mL and normal saline). However, no statistically significant decrease in the amount of bacteriophage was seen with biodegradable vancomycin beads over 24 h. CONCLUSION: These findings have important clinical ramifications in that they show local administration of bacteriophages with concomitant local vancomycin powder therapy should be avoided. Moreover, these findings should spearhead further research into bacteriophage stability in in vivo environments.

The biofilm community resurfaces: new findings and post-pandemic progress.

The ninth American Society for Microbiology Conference on Biofilms was convened in-person on 13-17 November 2022 in Charlotte, NC. As the first of these conferences since prior to the start of the COVID-19 pandemic, the energy among the participants of the conference was clear, and the meeting was a tremendous success. The mixture of >330 oral and poster presentations resoundingly embodied the vitality of biofilm research across a wide range of topics and multiple scientific disciplines. Special activities, including a pre-conference symposium for early career researchers, further enhanced the attendee experience. As a general theme, the conference was deliberately structured to provide high levels of participation and engagement among early career scientists.

Polymicrobial interaction between Lactobacillus and Saccharomyces cerevisiae: coexistence-relevant mechanisms.

The coordination of single or multiple microorganisms are required for the manufacture of traditional fermented foods, improving the flavour and nutrition of the food materials. However, both the additional economic benefits and safety concerns have been raised by microbiotas in fermented products. Among the fermented products, Lactobacillus and Saccharomyces cerevisiae are one of the stable microbiotas, suggesting their interaction is mediated by coexistence-relevant mechanisms and prevent to be excluded by other microbial species. Thus, aiming to guide the manufacture of fermented foods, this review will focus on interactions of coexistence-relevant mechanisms between Lactobacillus and S. cerevisiae, including metabolites communications, aggregation, and polymicrobial biofilm. Also, the molecular regulatory network of the coexistence-relevant mechanisms is discussed according to omics researches.

Resistome and virulome study on pathogenic Streptococcus agalactiae Guangzhou-SAG036.

Streptococcus agalactiae is considered as a leading case of bacterial infection among neonates. Although relative protection strategies have been performed in many high-income countries, resulting in a massive reduction in the occurrences of early-onset GBS disease, the late-onset disease has not affected. Here, the whole genome of S. agalactiae Guangzhou-SAG036 was sequenced by the Pacific Biosciences Sequel using the P4-C2 chemistry and the continuous long reads were used for de novo assembly using HGAP. Besides, genes prediction and multiply annotation were performed by comparing it with diverse databases. The whole genome has a length of 2,206,504 bp and contains 2162 predicted genes with an average G + C content of 35.85%. Based on the whole genome sequence, 2 large prophages, 20 virulence factors genes, and 8 antibiotic resistant genes were identified. MLST analysis revealed S. agalactiae Guangzhou-SAG036 was identified as ST-17. The virulence factors genes were identified with different functions including adherence, antiphagocytosis, spreading factor, immune evasion, invasion, toxin. Besides, the antibiotic-resistant genes may provide S. agalactiae with resistance to multi-drugs including erythromycin, streptomycin, azithromycin, spiramycin, ampicillin, kanamycin, cationic peptides, and tetracycline. Therefore, the infection of S. agalactiae Guangzhou-SAG036 ST-17 strain maybe caused by the complex virulence factors and multi-drugs resistance. These results contribute to further understand GBS epidemiology and surveillance targets.

Genomic analysis of a hop-resistance Lactobacillus brevis strain responsible for food spoilage and capable of entering into the VBNC state.

BACKGROUND: Lactobacillus brevis is a major contaminant of spoiled beer. And it was able to enter VBNC state and cause false negative detection, which poses a major challenge to the brewing industry. METHODS: The genomic DNA of L. brevis BM-LB13908 was extracted and purified to form a sequencing library that meets the quality requirements and was sequenced. The sequencing results were then screened and assembled to obtain the entire genome sequence of L. brevis. Predicted genes were annotated by GO database, KEGG pathway database and COG functional classification system. RESULTS: The final assembly yielded 275 scaffolds of a total length of 2 840 080 bp with a G + C content of 53.35%. There were 2357, 701, 1519 predicted genes with corresponding GO functional, COG functional, and KEGG biological pathway annotations, respectively. The genome of L. brevis BM-LB13908 contains hop resistance gene horA and multiple genes related to the formation of VBNC state. CONCLUSIONS: This report describes the draft genome sequence of L. brevis BM-LB13908, a spoilage strain isolated from finished beer sample. This study may support further study on L. brevis and other beer spoilage bacteria, and prevent and control beer spoilage caused by microorganisms.

Impact of Fixed Nitrogen Availability on Dehalococcoides mccartyi Reductive Dechlorination Activity.

Biostimulation to promote reductive dechlorination is widely practiced, but the value of adding an exogenous nitrogen (N) source (e.g., NH4+) during treatment is unclear. This study investigates the effect of NH4+ availability on organohalide-respiring Dehalococcoides mccartyi (Dhc) growth and reductive dechlorination in enrichment cultures derived from groundwater (PW4) and river sediment (TC) impacted with chlorinated ethenes. In PW4 cultures, the addition of NH4+ increased cis-1,2-dichloroethene (cDCE)-to-ethene dechlorination rates about 5-fold (20.6 ± 1.6 versus 3.8 ± 0.5 µM Cl- d-1), and the total number of Dhc 16S rRNA gene copies were about 43-fold higher in incubations with NH4+ ((1.8 ± 0.9) × 108 mL-1) compared to incubations without NH4+ ((4.1 ± 0.8) × 107 mL-1). In TC cultures, NH4+ also stimulated cDCE-to-ethene dechlorination and Dhc growth. Quantitative polymerase chain reaction (qPCR) revealed that Cornell-type Dhc capable of N2 fixation dominated PW4 cultures without NH4+, but their relative abundance decreased in cultures with NH4+ amendment (i.e., 99 versus 54% of total Dhc). Pinellas-type Dhc incapable of N2 fixation were responsible for cDCE dechlorination in TC cultures, and diazotrophic community members met their fixed N requirement in the medium without NH4+. Responses to NH4+ were apparent at the community level, and N2-fixing bacterial populations increased in incubations without NH4+. Quantitative assessment of Dhc nitrogenase genes, transcripts, and proteomics data linked Cornell-type Dhc nifD and nifK expression with fixed N limitation. NH4+ additions also demonstrated positive effects on Dhc in situ dechlorination activity in the vicinity of well PW4. These findings demonstrate that biostimulation with NH4+ can enhance Dhc reductive dechlorination rates; however, a "do nothing" approach that relies on indigenous diazotrophs can achieve similar dechlorination end points and avoids the potential for stalled dechlorination due to inhibitory levels of NH4+ or transformation products (i.e., nitrous oxide).

Understanding urban stormwater denitrification in bioretention internal water storage zones.

Conventional free-draining bioretention systems promote nitrate production and continual leaching to receiving waters. In this study, laboratory tests demonstrated the efficacy of an internal water storage zone (IWSZ) to target nitrate removal via denitrification. Experimental results confirmed that the carbon substrate characteristics (Willow Oak woodchip media) and the hydraulic retention time of nitrified stormwater affected nitrate removal performance. A 2.6-day batch treatment time reduced 3.0 mg-N/L to <0.01 mg/L, corresponding to a first-order denitrification rate constant of 0.0011 min-1 . Under various flow conditions, the associated hydraulic retention time may be used as a predictive measurement of nitrate removal performance. Scanning electron microscopy and 16S rRNA analysis of the woodchips showed that biofilms were present that could be responsible for anaerobic lignocellulose degradation and denitrification. This knowledge, along with evaluation of the biofilm community composition, reinforced the notion of a heterogeneous structure due to nutrient availability and hydrodynamic conditions. PRACTITIONER POINTS: Denitrification can occur using woodchips in a bioretention internal water storage zone. The denitrification rate is slow and may be limited during field-scale applications. A woodchip pretreatment did not provide long-term enhancement to the denitrification rate. Denitrification bacteria were found in the internal water storage zone.

Distribution of polychlorinated biphenyls in effluent from a large municipal wastewater treatment plant: Potential for bioremediation?

This study involved an evaluation of the potential for bioremediation of polychlorinated biphenyls (PCBs) in the effluent from a large municipal wastewater treatment plant. It was focused on the presence of PCBs in two types of effluents: the continuous effluent present during dry weather conditions and the intermittently present effluent that was present during wet weather due to incoming stormwater. The annual discharge of PCBs for both types of effluent was calculated based on a five-year dataset (2011-2015). In addition, the toxicity and bioremediation potential of the PCBs in the effluent were also assessed. It was found that the continuous effluent was responsible for the majority of the discharged PCB into the receiving river (1821 g for five years), while the intermittent effluent contributed 260 g over the five years. The average number of chlorine per biphenyl for the detected PCB congeners showed a 19% difference between the two types of effluent, which indicated a potential for organohalide respiration of PCBs during the continuous treatment. This was further supported by a high level of tri-, tetra- and penta-chlorinated congeners accounting for 75% of the anaerobically respired PCBs. Potential for aerobic degradation and thus biomineralization of PCBs was identified for both effluents. Furthermore, toxicity of 12 dioxin-like PCBs showed that normal operation of the wastewater reduced the toxicity throughout the wastewater treatment plant.

Biogeochemical cycling of metals impacting by microbial mobilization and immobilization.

Microbial mobilization and immobilization processes can affect the bioavailability and mobility of metals thereby influencing their toxicity and can therefore be utilized to treat solid and liquid wastes contaminated by metals. However, the microbial mobilization and immobilization of metals depends on the microbial metabolism, the environment conditions. In this review, mobilization and immobilization of metals are discussed with regard to the presence and function of involved microorganisms and in relation to applications such as bioleaching. Furthermore, the biosorption process is evaluated as a possible approach for microbial immobilization of metal on the basis of four mechanisms: (1) physical adsorption, (2) ion exchange, (3) complexation, and (4) microprecipitation. In addition, sulfide precipitation by sulfate reducing bacteria was included as an example of an application of microbial immobilization. Based on the evaluation and recommendations in this paper, bioremediation strategies for metals can be improved thus increasing the opportunity for field applications.

Kinetics and threshold level of 2,3,4,5-tetrachlorobiphenyl dechlorination by an organohalide respiring bacterium.

The time required for a PCB-contaminated site to recover cannot yet be predicted due in part to lack of quantitative information on rates of PCB dechlorination in the porewater phase. We developed a method to measure rate of dechlorination in the aqueous phase at very low PCB concentrations. This approach utilizes a polymer functioning concurrently as a passive dosing system for maintaining a steady-state PCB substrate concentration in the water phase and as a passive equilibrium sampler to monitor the dechlorination product. Rates of dechlorination of 2,3,4,5-tetrachlorobiphenyl (PCB 61) to 2,3,5-trichlorobiphenyl (PCB 23) by an organohalide respiring bacterium, Dehalobium chlorocoercia DF-1, were measured over an environmentally relevant range of 1 to 500 ng L(-1) in sediment-free medium using a high concentration of cells (>10(6) cells mL(-1)). The results indicate that rate of dechlorination is a linear function of PCB substrate concentration below the maximum aqueous solubility of PCB 61 and occurs at concentrations as low as 1 ng L(-1). Demonstration of PCB 61 dechlorination at environmentally relevant concentrations suggests that low numbers of organohalide respiring bacteria rather than bioavailability accounts for low rates of dechlorination typically observed in sediments. Using passive samplers to measure the concentration of dissolved PCBs in the porewater combined with knowledge of congener-specific rates for organohalide respirer(s), it will be possible to project the in situ rate and final concentration of PCBs for a specific site after treatment by bioaugmentation.

Do bacteriophages have activity in synovial fluid and against synovial fluid induced bacterial aggregates?

Bacteriophage therapy is a promising adjuvant therapy for the treatment of periprosthetic joint infections. However, there is a paucity of knowledge about the activity of bacteriophages in synovial fluid. Therefore, this study evaluated the activity of a clinically used bacteriophage in synovial fluid as well as the ability of that bacteriophage to prevent the formation of and eradicate bacteria in synovial fluid induced aggregates. The results of this study reinforce that synovial fluid induced aggregates form rapidly in numerous synovial fluid concentrations. More importantly, there was a statistically significant reduction in bacteriophage activity in synovial fluid compared to tryptic soy broth (p < 0.05) and the bacteriophage could not prevent the formation synovial fluid induced aggregates. Also the bacteriophage could not significantly reduce the amount of bacteria in the synovial fluid induced aggregates when compared to controls, and this was not secondary to resistance. Rather the reduced activity seems to be caused by bacteriophages being hindered in the ability to attach to bacterial receptors. We hypothesize this occurred because the viscosity of synovial fluid slowed bacteriophage interactions with planktonic bacteria and the synovial fluid polymers obstructed the bacteriophage attachment receptors thereby preventing attachment to bacteria in the aggregates. These findings have clinical ramifications, supporting the use of bacteriophage therapy as an adjunct to surgical interventions and not in isolation, at the nascent stage. While these findings show a shortcoming of bacteriophage therapy in periprosthetic joint infections, the knowledge gained should spearhead further research to ultimately devise effective and reproducible bacteriophage therapeutics.

Differential alteration in Lactiplantibacillus plantarum subsp. plantarum quorum-sensing systems and reduced Candida albicans yeast survival and virulence gene expression in dual-species interaction.

Candida albicans (C. albicans) and Lactiplantibacillus plantarum subsp. plantarum (L. plantarum) are frequently identified in various niches, but their dual-species interaction, especially with C. albicans in yeast form, remains unclear. This study aimed to investigate the dual-species interaction of L. plantarum and C. albicans, including proliferation, morphology, and transcriptomes examined by selective agar plate counting, microscopy, and polymicrobial RNA-seq, respectively. Maintaining a stable and unchanged growth rate, L. plantarum inhibited C. albicans yeast cell proliferation but not hyphal growth. Combining optical microscopy and atomic force microscopy, cell-to-cell direct contact and co-aggregation with L. plantarum cells surrounding C. albicans yeast cells were observed during dual-species interaction. Reduced C. albicans yeast cell proliferation in mixed culture was partially due to L. plantarum cell-free culture supernatant but not the acidic environment. Upon polymicrobial transcriptomics analysis, interesting changes were identified in both L. plantarum and C. albicans gene expression. First, two L. plantarum quorum-sensing systems showed contrary changes, with the activation of lamBDCA and repression of luxS. Second, the upregulation of stress response-related genes and downregulation of cell cycle, cell survival, and cell integrity-related pathways were identified in C. albicans, possibly connected to the stress posed by L. plantarum and the reduced yeast cell proliferation. Third, a large scale of pathogenesis and virulence factors were downregulated in C. albicans, indicating the potential interruption of pathogenic activities by L. plantarum. Fourth, partial metabolism and transport pathways were changed in L. plantarum and C. albicans. The information in this study might aid in understanding the behavior of L. plantarum and C. albicans in dual-species interaction.IMPORTANCEThe anti-Candida albicans activity of Lactiplantibacillus plantarum has been explored in the past decades. However, the importance of C. albicans yeast form and the effect of C. albicans on L. plantarum had also been omitted. In this study, the dual-species interaction of L. plantarum and C. albicans was investigated with a focus on the transcriptomes. Cell-to-cell direct contact and co-aggregation with L. plantarum cells surrounding C. albicans yeast cells were observed. Upon polymicrobial transcriptomics analysis, interesting changes were identified, including contrary changes in two L. plantarum quorum-sensing systems and reduced cell survival-related pathways and pathogenesis determinants in C. albicans.

Applications of biofilms in bioremediation and biotransformation of persistent organic pollutants, pharmaceuticals/personal care products, and heavy metals.

In this review, the strategies being employed to exploit the inherent durability of biofilms and the diverse nutrient cycling of the microbiome for bioremediation are explored. Focus will be given to halogenated compounds, hydrocarbons, pharmaceuticals, and personal care products as well as some heavy metals and toxic minerals, as these groups represent the majority of priority pollutants. For decades, industrial processes have been creating waste all around the world, resulting in contaminated sediments and subsequent, far-reaching dispersal into aquatic environments. As persistent pollutants have accumulated and are still being created and disposed, the incentive to find suitable and more efficient solutions to effectively detoxify the environment is even greater. Indigenous bacterial communities are capable of metabolizing persistent organic pollutants and oxidizing heavy metal contaminants. However, their low abundance and activity in the environment, difficulties accessing the contaminant or nutrient limitations in the environment all prevent the processes from occurring as quickly as desired and thus reaching the proposed clean-up goals. Biofilm communities provide among other things a beneficial structure, possibility for nutrient, and genetic exchange to participating microorganisms as well as protection from the surrounding environment concerning for instance predation and chemical and shear stresses. Biofilms can also be utilized in other ways as biomarkers for monitoring of stream water quality from for instance mine drainage. The durability and structure of biofilms together with the diverse array of structural and metabolic characteristics make these communities attractive actors in biofilm-mediated remediation solutions and ecosystem monitoring.

Distribution and biodegradation potential of polycyclic aromatic hydrocarbons (PAHs) accumulated in media of a stormwater bioretention.

Polycyclic aromatic hydrocarbons (PAHs) are a group of organic compounds that can be captured and accumulate in the bioretention cell media, which may lead to secondary pollution and ecological risks. This research aimed to understand the spatial distribution of 16 priority PAHs in bioretention media, identify their sources, evaluate their ecological impact, and assess the potential for their aerobic biodegradation. The highest total PAH concentration (25.5 ± 1.7 µg/g) was observed 1.83 m from the inlet and 10-15 cm deep. The individual PAHs with the highest concentrations were benzo [g,h,i]perylene in February (1.8 ± 0.8 µg/g) and pyrene in June (1.8 ± 0.8 µg/g). Data indicated that primary sources of PAHs were fossil fuel combustion and petroleum. The ecological impact and toxicity of the media were assessed by probable effect concentrations (PECs) and benzo [a]pyrene total toxicity equivalent (BaP-TEQ). The results showed that the concentrations of pyrene and chrysene exceeded the PECs, and the average BaP-TEQ was 1.64 µg/g, primarily caused by benzo [a]pyrene. The functional gene (C12O) of PAH-ring cleaving dioxygenases (PAH-RCD) was present in the surface media, which indicated that aerobic biodegradation of PAHs was possible. Overall, this study revealed the PAHs accumulated most at medium distance and depth, where biodegradation may be limited. Thus, the accumulation of PAHs below the surface of the bioretention cell may need to be considered during long-term operation and maintenance.

Use of organic amendments derived from biosolids for groundwater remediation of TCE.

Many groundwater aquifers around the world are contaminated with trichloroethene (TCE), which can be harmful to human and ecosystem health. Permeable Reactive Barriers (PRB) are commonly used to remediate TCE-contaminated groundwaters especially when a point source is ill defined. Using biosolids from wastewater treatment plants as a PRB filling material can provide a source of carbon and nutrients for dechlorinating bacterial activity. However, under the anaerobic conditions of the PRB, methanogenesis can also occur which can adversely affect reductive dechlorination. We conducted bench scale experiments to evaluate the effect of biosolids on TCE reductive dechlorination and found that methanogenesis was significantly higher in the reactors amended with biosolids, but that reductive dechlorination did not decrease. Furthermore, the microbial communities in the biosolid-enhanced reactors were more abundant with obligate dechlorinators, such as Dehalobacter and Dehalogenimonas, than the reactors amended only with the dechlorinating culture. The biosolids enhanced the presence and abundance of methanogens and acetogens, which had a positive effect on maintaining an efficient dechlorinating microbial community and provided the necessary enzymes, cofactors, and electron donors. These results indicate that waste materials such as biosolids can be turned into a valuable resource for bioremediation of TCE and likely other contaminants.

Evaluation of multiple analytical methods for SARS-CoV-2 surveillance in wastewater samples.

In this study, 14 virus concentration protocols based on centrifugation, filtration, polyethylene glycol (PEG) precipitation and ultrafiltration were tested for their efficacy for the quantification of SARS-CoV-2 in wastewater samples. These protocols were paired with four RNA extraction procedures resulting in a combination of 50 unique approaches. Bovine respiratory syncytial virus (BRSV) was used as a process control and seeded in each wastewater sample subjected to all 50 protocols. The recovery of BRSV obtained through the application of 50 unique approaches ranged from <0.03 to 64.7% (±1.6%). Combination of centrifugation as the solid removal step, ultrafiltration (Amicon-UF-15; 100 kDa cut-off; protocol 9) as the primary virus concentration method, and Zymo Quick-RNA extraction kit provided the highest BRSV recovery (64.7 ± 1.6%). To determine the impact of prolonged storage of large wastewater sample volume (900 mL) at -20 °C on enveloped virus decay, the BRSV seeded wastewaters samples were stored at -20 °C up to 110 days and analyzed using the most efficient concentration (protocol 9) and extraction (Zymo Quick-RNA kit) methods. BRSV RNA followed a first-order decay rate (k = 0.04/h with r2 = 0.99) in wastewater. Finally, 21 wastewater influent samples from five wastewater treatment plants (WWTPs) in southern Maryland, USA were analyzed between May to August 2020 to determine SARS-CoV-2 RNA concentrations. SARS-CoV-2 RNA was quantifiable in 17/21 (81%) of the influent wastewater samples with concentration ranging from 1.10 (±0.10) × 104 to 2.38 (±0.16) × 106 gene copies/L. Among the RT-qPCR assays tested, US CDC N1 assay was the most sensitive followed by US CDC N2, E_Sarbeco, and RdRp assays. Data presented in this study may enhance our understanding on the effective concentration and extraction of SARS-CoV-2 from wastewater.

Presence of bacteria capable of PCB biotransformation in stormwater bioretention cells.

Core samples from bioretention cell media as well as surface stormwater sediment samples from seven urban areas were collected to assess the potential for biotransformation activity of polychlorinated biphenyls (PCBs). The presence of putative organohalide-respiring bacteria in these samples was studied. Based on extracted DNA, Dehalobacter, Dehalogenimonas and Dehalococcoides were detected. Other organohalide-respiring bacteria like Desulfitobacterium and Sulfurospirillum were not studied. Bacteria containing the genes encoding for biphenyl 2,3-dioxygenase (bphA) or 2,3-dihydroxybiphenyl 1,2-dioxygenase (bphC) were detected in 29 of the 32 samples. These genes are key factors in PCB aerobic degradation. Transcribed bacterial genes from putative organohalide-respiring bacteria as well as genes encoding for bphA and bphC were obtained from the microbial community, thus showing the potential of organohalide respiration of PCBs and aerobic PCB degradation under both aerobic and anaerobic conditions in the surface samples collected at the bioretention site. Presence and concentrations of 209 PCB congeners in the bioretention media were also assessed. The total PCB concentration ranged from 38.4 ± 2.3 ng/g at the top layer of the inlet to 11.6 ± 1.2 ng/g at 20-30 cm at 3 m from the inlet. These results provide documentation that bacteria capable of PCB transformation, including both anaerobic dechlorination and aerobic degradation, were present and active in the bioretention.

Chemical characterization of urban stormwater: Traditional and emerging contaminants.

Increases in urbanization have led to increased stormwater runoff and mobilization of pollutants from urban watersheds. Discharge of these pollutants often leads to contamination of receiving water bodies. Chemical characterization of urban stormwater is necessary to gain deeper insights into the ecological impacts of urban runoff and to evaluate parameters that influence possible treatment technologies. This study assessed stormwater event mean concentrations and particle size fractions from field studies reported in national/international stormwater quality databases (The National Stormwater Quality and The Best Management Practices databases) and peer-reviewed literature. This characterization of urban stormwater includes statistical evaluation of probability distribution, consideration of dissolved and particulate-bound pollutants and focuses on partitioning and speciation behavior. Solids, nutrients, metals, organic pollutants, and bacterial pathogen indicators were evaluated. A significant fraction of stormwater phosphorus, metals and organic pollutants are particle-bound. Results from the speciation of metals demonstrated that metals are predominantly present as either inner-sphere or electrostatic complexes with dissolved organic matter. This study provides a comprehensive overview of the myriad pollutants found in urban stormwater and provides a starting point for addressing ubiquitous and emerging contaminants. Finally, research needs for further detailed stormwater characterization were identified.