Comparison of holmium:yttrium-aluminium-garnet (YAG), thulium fiber laser, and pulsed thulium:YAG lasers on soft tissue: an ex vivo study.

OBJECTIVES: To assess laser-tissue interactions through ablation, coagulation, and carbonisation characteristics in a non-perfused porcine kidney model between three pulsed lasers: holmium (Ho): yttrium-aluminium-garnet (YAG), thulium fiber laser (TFL), and pulsed thulium (p-Tm):YAG. MATERIALS AND METHODS: A 150-W Ho:YAG, a 60-W TFL, and a 100-W p-Tm:YAG lasers were compared. The laser settings that can be set identically between the three lasers and be clinically relevant for prostate laser enucleation were identified and used on fresh, unfrozen porcine kidneys. Laser incisions were performed using stripped laser fibers of 365 and 550 µm, set at distances of 0 and 1 mm from the tissue surface at a constant speed of 2 mm/s. Histological analysis evaluated shape, depth, width of the incision, axial coagulation depth, and presence of carbonisation. RESULTS: Incision depths, widths, and coagulation zones were greater with Ho:YAG and p-Tm:YAG lasers than TFL. Although no carbonisation was found with the Ho:YAG and p-Tm:YAG lasers, it was common with TFL, especially at high frequencies. The shapes of the incisions and coagulation zones were more regular and homogeneous with the p-Tm:YAG laser and TFL than with Ho:YAG laser. Regardless of the laser used, short pulse durations resulted in deeper incisions than long pulse durations. Concerning the distance, we found that to be effective, TFL had to be used in contact with the tissue. Finally, 365-µm fibers resulted in deeper incisions, while 550-µm fibers led to wider incisions and larger coagulation zones. CONCLUSION: Histological analysis revealed greater tissue penetration with the p-Tm:YAG laser compared to the TFL, while remaining less than with Ho:YAG. Its coagulation properties seem interesting insofar as it provides homogeneous coagulation without carbonisation, while incisions remained uniform without tissue laceration. Thus, the p-Tm:YAG laser appears to be an effective alternative to Ho:YAG and TFL lasers in prostate surgery.

How much energy do we need to ablate 1 cubic millimeter of stone during Thulium Fiber Laser lithotripsy? An in vitro study.

INTRODUCTION: Both Holmium:yttrium-aluminium-garnet (Ho:YAG) laser and Thulium Fiber Laser (TFL) can effectively treat all urinary stone types. This in vitro study evaluated the ablation volume per pulse (AVP) and required energy needed to ablate 1mm3 (RE, J/mm3) of various stone types at different laser settings with TFL. METHODS: 272-µm core-diameter laser fibers (Boston Scientific©) were connected to a 50 Watts TFL generator (IPG®). An experimental setup immerged human stones of calcium oxalate monohydrate (COM), uric acid (UA), and cystine (CYS) with a single pulse lasing emission (0.5/0.8/1 J), in contact mode. Stones were dried out before three-dimensional scanning to measure AVP and deduce from the pulse energy (PE) and AVP the RE. A direct comparison with known Ho:YAG's AVP and RE was then carried out. RESULTS: AVP for COM stones was significantly greater than those for CYS stones and similar to UA stones (p = 0.02 and p = 0.06, respectively). If AVP increased with PE against COM and UA stones, AVP decreased against CYS stones. 1 J PE resulted in a threefold lower RE compared with other PE for COM stones. On the contrary, RE for CYS increased with PE, whereas PE did not had influence on RE for UA. TFL was associated with greater AVP for COM, but lower for UA and CYS stones compared to Ho:YAG laser. CONCLUSION: This in vitro study firstly describes the ablation volume per pulse and required energy to treat a cubic millimeter of three frequent human stone types, and suggest TFL could not be suited for cystine. Therefore, stone composition could be considered when choosing the laser source for lithotripsy.

Comparison of the ablation rates, fissures and fragments produced with 150 µm and 272 µm laser fibers with superpulsed thulium fiber laser: an in vitro study.

INTRODUCTION: Holmium:YAG(Ho:YAG) is currently the standard for lithotripsy. Superpulsed Thulium Fiber Laser(TFL) has been evaluated as an alternative for lithotripsy, using laser fibers with core-diameters(CDF) down to 50 µm and additional available settings suitable for "dusting" technique. This in-vitro study compared ablation rates, fissures and fragments' size with 150µmCDF or 272µmCDF with different laser settings using TFL and Ho:YAG. METHODS: 150CDF and 272CDF were compared using three settings for TFL "fine dusting"(FD:0.15 J/100 Hz); "dusting"(D:0.5 J/30 Hz); "fragmentation"(Fr:1 J/15 Hz) and Ho:YAG(D and Fr). An experimental setup consisting of immerged 10 mm cubes of artificial hard(H) or soft(S) stone phantoms was used with a 20 s' lasing time and a spiral trajectory, in contact mode. Fragments (acquired through sieves) and stones were observed under optical microscopy before three-dimensional scanning to measure fragments and fissures(DOF) mean diameters and ablation volumes. RESULTS: Ablation volumes in with 150CDF-TFL and 272CDF-TFL were higher than those for 272CDF-Ho:YAG in both "dusting" (twofold and threefold) and "fragmentation"(1,5-fold and twofold). "Fine dusting" ablation rates with 150CDF-TFL and 272CDF-TFL were respectively at least 1,5-fold and twofold higher than those for 272CDF-Ho:YAG in "dusting". 150CDF produced significantly smaller DOF than 272CDF in all settings against S and H except in fragmentation. 150CDF produced lower fragments' diameter than 272CDF in all settings except dusting. CONCLUSION: These preliminary studies demonstrate that at equal settings and CDF, TFL ablation rates are at least two-fold higher than those with Ho:YAG. 150CDF produces smaller fissures and fragments (that meets the definition of "dusting" lithotripsy) than 272CDF and higher ablation volumes than Ho:YAG.

Miniature laser powder bed fusion system for in situ synchrotron x-ray micro-computed tomography experiments at the European Synchrotron Radiation Facility.

We describe our miniature laser powder bed fusion (L-PBF) system for in situ synchrotron x-ray micro-computed tomography (XCT) at the European Synchrotron Radiation Facility. This replicator was designed to extend the characterization of L-PBF to 3D. This instrument fills in a technical gap because the existing replicators were mostly designed to shed light on the dynamic mechanisms involved in molten pool formation but, therefore, suffered from a lack of 3D information. Technical details regarding the setup and beamline integration are given. Experimental validations via post-mortem XCT scans and in situ scans acquired during experiments conducted at the BM05 beamline of the European Synchrotron Radiation Facility are provided. Based on a few illustrative examples, we show that such a replicator opens the path to collect key 3D information that to date could not be available. Our miniature instrument complements the other replicators developed in the world by other research groups that enable operando x-ray imaging (radiography) and operando x-ray diffraction.