Biocompatibility analysis in subcutaneous tissue and physico-chemical analysis of pre-mixed calcium silicate-based sealers.

OBJECTIVES: To evaluate the biocompatibility, physical and chemical properties of three pre-mixed calcium silicate-based sealers and an epoxy resin-based material were assessed. Pre-mixed sealers supposedly obtain water from the root canal moist to hydrate and set. MATERIALS AND METHODS: Polyethylene tubes were filled with the materials Bio-C Sealer Ion+, Bio-C Sealer, EndoSequence BC Sealer and AH Plus Jet, or left empty and surgically implanted in the subcutaneous tissue of Wistar rats. The animals were euthanised and the tubes and tissue were removed for histological analysis and scanning electron microscopy (SEM) coupled with energy-dispersive spectrometry (EDS). Materials' surface chemical characterisation was assessed using Raman spectroscopy and SEM/EDS. Flow, setting time (in two conditions), solubility, radiopacity and pH were also analysed. ANOVA and Bonferroni correction were performed for comparisons (P < 0.05). RESULTS: Inflammatory response observed in the tissues subsided from 7 to 30 days. Tungsten migration could be detected in the surrounding tissue following AH Plus Jet implantation. All calcium silicate-based sealers exhibited zirconium oxide (radiopacifier) and tricalcium silicate peaks before and after implantation. All materials exhibited flow values above 17 mm. An approximately tenfold difference was observed between the plaster- and metal-mould setting times of the calcium silicate cements indicating its sensitivity to moist variations and solubility above 8% was also observed for these materials. CONCLUSIONS: Pre-mixed materials exhibited variable setting time and solubility with a decreasing inflammatory response. CLINICAL RELEVANCE: The variable moist-dependant setting time with high solubility poses a concern for the clinical use of these pre-mixed sealers.

Physical, chemical, and biological properties of white MTA with additions of AlF3.

OBJECTIVES: Addition of aluminum fluoride (AlF3) to MTA was tested to inhibit dental discoloration. MATERIALS AND METHODS: MTA Angelus with 0, 5, 15, and 45% AlF3 were tested. The set cements were characterized using scanning electron microscopy, energy-dispersive spectroscopy, and X-ray diffraction. Radiopacity and setting time were analyzed according to ANSI/ADA 57 and ASTM C266-08. Volume change was evaluated using volumetric micro-CT analysis. The pH and calcium ion release were assessed after 3 and 24 h and 28 days. Dental discoloration in contact with the cements was assessed after 24 h and 28 and 90 days of contact with bovine and human dentine. Tissue reaction to subcutaneous implantation in rats was examined after 30 and 60 days. RESULTS: AlF3 altered the microstructure of MTA. The addition of 5% AlF3 did not significantly alter the radiopacity, setting time, and volume change (p > 0.05). pH and calcium ion release significantly increased with addition of AlF3 (p > 0.05). All the tested proportions of AlF3 prevented the dental darkening verified for MTA Angelus in bovine and human teeth. AlF3 did not interfere in inflammatory response of MTA in all periods of analysis; otherwise, lower amounts showed less intense inflammatory infiltrate. CLINICAL RELEVANCE: AlF3 prevents destabilization of bismuth oxide and consequent tooth darkening, frequently verified in clinical practice when using white MTA. CONCLUSIONS: The use of 5% of AlF3 in combination to MTA resulted in a cement that did not result in dental discoloration and did not affect significantly physical, chemical, and biological properties.

Doxycycline and Autogenous Bone in Repair of Critical-Size Defects.

PURPOSE: The association of doxycycline (DOX) and autogenous bone on repair of critical-size defects was evaluated. MATERIALS AND METHODS: Fifty albino rats were divided into 5 groups (n = 10). A 5-mm diameter defect was treated with: control (CO)-blood clot; DOX in Natrosol (NAT)-10% gel; NAT-gel; particulate autogenous bone (PAB); and PAB + DOX - PAB associated with 10% DOX gel. The animals were euthanized at 4 and 8 weeks postoperatively. Histomorphometric analysis was performed to assess the percentage of new bone in the defect area. Statistical analysis of the results was performed using analysis of variance and the Tukey test (P < 0.05). RESULTS: The results showed that new bone formation was limited to the margins of the defect. At 4 and 8 weeks, the group PAB + DOX showed higher bone formation (38.59% and 47.86%, respectively), with statistical difference in comparison with the CO (19.52%) at 4 weeks and CO (18.80%), DOX (22.05%), and NAT (15.89%) at 8 weeks (P < 0.05). CONCLUSIONS: The association of 10% DOX with autogenous bone significantly improved bone healing in critical-size defects.

Dental discoloration caused by bismuth oxide in MTA in the presence of sodium hypochlorite.

OBJECTIVES: The aim of this research was to analyse the dental discolouration caused by mineral trioxide aggregate (MTA) induced by bismuth oxide and also assess the colour stability of other dental cements. MATERIALS AND METHODS: Bismuth oxide, calcium tungstate and zirconium oxide were placed in contact with sodium hypochlorite for 24 h after which they were dried and photographed. Phase analyses were performed by X-ray diffraction (XRD) of radiopacifiers before and after immersion in sodium hypochlorite. Furthermore, teeth previously immersed in water or sodium hypochlorite were filled with MTA Angelus, Portland cement (PC), PC with 20 % zirconium oxide, PC with 20 % calcium tungstate and Biodentine. Teeth were immersed for 28 days in Hank's balanced salt solution after which they were sectioned and characterized using scanning electron microscopy (SEM) with energy-dispersive mapping and stereomicroscopy. RESULTS: Bismuth oxide in contact with sodium hypochlorite exhibited a change in colour from light yellow to dark brown. XRD analysis demonstrated peaks for radiopacifier and sodium chloride in samples immersed in sodium hypochlorite. The SEM images of the dentine to material interface showed alteration in material microstructure for MTA Angelus and Biodentine with depletion in calcium content in the material. The energy-dispersive maps showed migration of radiopacifier and silicon in dentine. CONCLUSIONS: MTA Angelus in contact with a tooth previously immersed in sodium hypochlorite resulted in colour alteration at the cement/dentine interface. CLINICAL RELEVANCE: MTA Angelus should not be used after irrigation with sodium hypochlorite as this will result in tooth discoloration.

Prevalence and reasons for referrals to the Endodontics Specialty Clinic at the Piracicaba Dental School.

Dental referrals to the Endodontics Specialty Clinic (ESC) are routine owing to the complexity of endodontic treatments. To obtain a better prognosis for treatment, students/dentists must perceive their technical limits. This study sought to investigate the referrals of patients to the ESC from different clinics of the Piracicaba Dental School, State University of Campinas - SP, Brazil, and check: a) the demographic profile of patients and the most commonly affected tooth; b) the clinic with the largest number of referrals; c) the reasons for referrals; d) the complexity of the cases; e) and the difficulty in assessing the referred cases based on the classification provided by the American Association of Endodontists (AAE) and Souza-Filho. The study sample consisted of patients' electronic dental referral records from February 2015 to June 2019. A total of 1,707 patients were referred to the ESC during the study period, and 62.4% were female. Lower molars were the most frequently involved teeth (34.8%), and 60.7% of the cases were referred due to the presence of root curvature. The AAE classification showed prevalence of highly difficult cases (71.3%), whereas Souza-Filho classification demonstrated a high rate of class III cases (85.8%). This study highlights the difficulties encountered by undergraduate students before or during endodontic treatments, reinforcing the need for clear criteria for selecting cases appropriate for each education level, thus improving endodontic treatment prognosis.

Effect of antimicrobial photodynamic therapy on the reduction of bacteria and virulence factors in teeth with primary endodontic infection.

OBJECTIVE: To evaluate the effectiveness of supplemental photodynamic therapy for improving the bacterial removal and the levels of lipopolysaccharide (LPS) and lipoteichoic acid (LTA) by conducting a clinical trial. METHODOLOGY: Twenty-four root canals with pulp necrosis and periapical lesion were selected and randomly divided into conventional group using endodontic treatment with chemo-mechanical preparation (CMP) alone (n = 12) and a group using antimicrobial photodynamic therapy (aPDT) after CMP (n = 12). The samples were collected before and after CMP (conventional group) and after photodynamic therapy (aPDT group). A photosensitizer (0.005% methylene blue) was applied to the root canal for 3 minutes after CMP, whereas aPDT was performed by using a red laser with a power of 30Mw and energy density of 9J/cm2 for 90 s per root canal. Culture technique was performed to determine the bacterial colony forming units. LPS and LTA levels were quantified by using limulus amoebocyte lysate (LAL) assay and enzyme-linked immunosorbent assay (ELISA), respectively. RESULTS: All samples showed growth of viable bacteria on Fastidious Anaerobe Agar (FAA), with an average of 5.19 × 105 CFU/ mL. CMP was effective in decreasing viable bacteria (p < 0.05), whereas there was a significant decrease (p < 0.05) in the samples treated with aPDT compared to those submitted to CMP. LPS and LTA were detected in all initial samples, with mean values of 20.561 EU/mL and 430.91 pg/mL, respectively. Both CMP and aPDT groups significantly decreased the levels of LPS and LTA (p < 0.05), with a statistical difference between the groups regarding aPDT (p < 0.05). CONCLUSION: Photodynamic therapy as an adjunct to CMP proved to be effective in improving root canal disinfection and reducing the LPS and LTA levels in teeth with primary endodontic infection.

Influence of working length and anatomical complexities on the apical root canal filling: a nano-CT study.

The present study aimed to compare the filled volume by gutta-percha and sealer in the apical region of the main canal and ramifications, after instrumentation at two different working lengths using nano-computed tomography (nano-CT). Twenty-two premolars with apical ramifications were selected after micro-computed tomography evaluation and were randomly divided into groups for further endodontic instrumentation at two different working lengths: G1 - Root canals shaped 1 mm short of the apical foramen (n=11), and G2 - Root canals shaped at the apical foramen (n=11). After completing root treatment, nano-CT images were acquired, and the filled volume by gutta-percha and sealer in the main canal apical 0-4 mm and 0-1 mm ranges, and apical ramifications were objectively measured by an operator specialized in both radiology and endodontics, blinded for both groups. The Mann-Whitney test was applied to compare both groups regarding the filling of the main canal apical ranges and apical ramifications with a significance level of 5% (α ≤ 0.05). It was observed that root canals shaped at the apical foramen had a larger volume of the main canal filled than root canals shaped 1 mm short of the apical foramen, at both apical ranges (0-4 and 0-1 mm) (p<0.05). Regarding the filling of the apical ramifications, there was no significant difference between groups (p>0.05). In conclusion, the root canals shaped at apical foramen exhibited increased filling volume of the main canal in the apical region. However, neither of both working lengths influenced filling of the apical ramifications.

Can strontium replace calcium in bioactive materials for dental applications?

The substitution of calcium with strontium in bioactive materials has been promising but there has been some concern over the material instability and possible toxicity. The aim of this research was the synthesis and characterization of calcium and strontium substituted bioactive materials and assessment of interactions with local tissues and peripheral elemental migration in an animal model. A bioactive glass, hydroxyapatite and hydraulic calcium silicate with 50% or 100% calcium substitution with strontium were developed and the set materials were characterized immediately after setting and after 30 and 180-days in solution. Following subcutaneous implantation, the local (tissue histology, elemental migration) and systemic effects (elemental deposition after organ digestion) were assessed. The strontium-replaced silicate cements resulted in the synthesis of partially substituted phases and strontium leaching at all-time points. The strontium silicate implanted in the animal model could not be retrieved in over half of the specimens showing the high rate of material digestion. Tissue histology showed that all materials caused inflammation after 30 days of implantation however this subsided and angiogenesis occurred after 180 days. Strontium was not detected in the local tissues or the peripheral organs while all calcium containing materials caused calcium deposition in the kidneys. The tricalcium silicate caused elemental migration of calcium and silicon in the local tissues shown by the elemental mapping but no deposition of calcium was identified in the peripheral organs verified by the assessment of the digested tissues. Strontium can substitute calcium in bioactive materials without adverse local or systemic effects.

The effect of photodynamic therapy on postoperative pain in teeth with primary endodontic infection.

INTRODUCTION: The objective of this study was to investigate the action of photodynamic therapy on pain control after endodontic treatment in asymptomatic teeth with a primary infection, within a single visit. METHODS: Sixty (60) single-rooted teeth with pulp necrosis and periapical lesions were selected and randomly divided into two (2) groups (n = 30), according to the protocol; a control group (CG) and a group using photodynamic therapy (aPDT). The canals were instrumented with Reciproc files # 25 up to 40 along the entire length of the canal, using 2% chlorhexidine gel as the auxiliary chemical substance, followed by irrigation with sterile saline. aPDT consited of 0.005% methylene blue as photosensitizer, using AsGaAl diode laser, 660 nm wavelength, 100 mW of power and 9 J of energy, using optical fibers with 365 µm in diameter. The canals were filled with Endomethasone N cement. RESULTS: Pain intensity was assessed at 8, 12, 24, 48, 72 h and 1 week after endodontic treatment using a visual analogue scale. The level of pain was classified as none (0), mild (1-3), moderate (4-7) or severe (8-10). The data were at a significance level of 5%. There was a statistically significant difference (p<0.05) in the periods of 8, 12, 24, 48 and 72 h between the control group and the aPDT group. After 1 week, there was no statistically significant difference. CONCLUSIONS: It is concluded that photodynamic therapy had a significant effect on decreasing post-endodontic treatment pain in teeth with necrotic pulp and asymptomatic periapical lesions.

Antimicrobial Activity of Calcium Silicate-Based Dental Materials: A Literature Review.

Endodontic biomaterials have significantly improved dental treatment techniques in several aspects now that they can be used for vital pulp treatments, as temporary intracanal medication, in definitive fillings, in apical surgeries, and for regenerative procedures. Calcium silicate-based cement is a class of dental material that is used in endodontics in direct contact with the dental structures, connective tissue, and bone. Because the material interacts with biological tissues and stimulates biomineralization processes, its properties are of major importance. The main challenge in endodontic treatments is the elimination of biofilms that are present in the root canal system anatomical complexities, as it remains even after chemical-mechanical preparation and disinfection procedures. Thus, an additional challenge for these biomaterials is to exert antimicrobial activity while maintaining their biological properties in parallel. This article reviews the literature for studies considering the antimicrobial properties of calcium silicate-based dental biomaterials used in endodontic practice. Considering the reviewed studies, it can be affirmed that the reduced antimicrobial effect exhibited by calcium silicate-based endodontic materials clearly emphasizes that all clinical procedures prior to their use must be carefully performed. Future studies for the evaluation of these materials, and especially newly proposed materials, under poly-microbial biofilms associated with endodontic diseases will be necessary.

Investigation of a modified hydraulic calcium silicate-based material - Bio-C Pulpo.

This study evaluated the physicochemical, biological, and antimicrobial properties of a new hydraulic calcium silicate-based modified material, and compared it with MTA Repair HP and MTA Angelus. The materials were assessed regarding color luminosity (L), color change, radiopacity, setting time, and ISO 6876:2012 linear flow. Volumetric filling and volume change were evaluated using microcomputed-tomography (µCT). Chemical characterization after 28 days in Hank's Balanced Salt Solution (HBSS) and pH analysis were also assessed. Biological characterization of cytotoxicity and microbiological assessment were also undertaken. Shapiro-Wilk, ANOVA, Levene and post hoc analyses with Bonferroni correction were performed, adopting a 5% significance level (p <0.05). Bio-C Pulpo exhibited the highest L values after 90 days. All tested materials demonstrated color change during the analyses, and had radiopacity above 5 mm Al. MTA Repair HP set faster than Bio-C Pulpo, whereas the latter had the highest linear flow. MTA Repair HP had the highest volumetric filling in µCT analysis. Bio-C Pulpo showed the highest alkalinity during all tested periods, and the highest volumetric loss (above 9%), in comparison with MTA Repair HP and MTA Angelus. Bio-C Pulpo did not form calcium hydroxide after hydration. MTA Repair HP demonstrated the highest cytocompatibility, and Bio-C Pulpo, the highest cytotoxicity. No inhibition halos were observed for any material, and similar higher turbidity values were seen after direct contact. Composition additives used in Bio-C Pulpo modified its properties, and both the absence of calcium hydroxide deposition after hydration, and the related cytotoxicity of this material are of particular concern.

Calcium Silicate-Based Sealers Do Not Reduce the Risk and Intensity of Postoperative Pain after Root Canal Treatment when Compared with Epoxy Resin-Based Sealers: A Systematic Review and Meta-Analysis.

This review aims to evaluate whether root canal obturation with calcium silicate-based (CSB) sealers reduces the risk and intensity of endodontic postoperative pain when compared to epoxy resin-based (ERB) sealers. The review was registered at PROSPERO (CRD42020169255). Two independent reviewers conducted an electronic search in PubMed, Scopus, EMBASE, Web of Science, Cochrane Library and LILACS until November 2020 and included only randomized clinical trials with adult health participants undergoing root canal treatment. After selection, the JBI Critical Appraisal tool was used to assess the risk of bias. A fixed-effect meta-analysis was performed to summarize the results of pain risk and pain intensity at time intervals of 24 and 48 hours. Finally, the certainty of evidence was assessed using the GRADE approach. The search resulted in 1,206 records, of which five studies (n = 421 patients) met the eligibility criteria and presented moderate to low risk of bias. There was no significant difference between groups in the risk of pain in the first 24 hours (relative risk or RR = 0.83, 95% confidence interval or CI: 0.60, 1.16, I 2 =) or 48 hours (RR = 0.56, 95% CI: 0.26, 1.21, I 2 =). Silicate-based sealers led to lower pain intensity only at 48 hours (mean and standard deviation = 0.37, 95% CI: 0.69, 0.05). All analyses revealed low heterogeneity (I 2 < 25%). The evidence presented moderate level of certainty. Currently available evidence has shown that there is no difference between CSB and ERB sealers in the risk or intensity of postoperative pain.

Dental discoloration caused by Grey-MTAFlow cement: analysis of its physicochemical, biological and antimicrobial properties.

Tricalcium silicate-based cement are materials used in reparative and regenerative procedures in endodontics. A recently proposed formulation aimed to enhance handling during clinical use with a versatile material applicable by syringe. Although, the use of bismuth oxide as radiopacifier and grey raw powder are drawbacks considering aesthetics. Objectives Evaluate physicochemical, biological, and antimicrobial properties of Grey-MTAFlow (Ultradent) and assess whether the addition of zinc oxide (ZnO) prevents dentinal discoloration caused by bismuth oxide. Methodology Grey-MTAFlow was manipulated in 'thin' consistency for all tests. Luminosity, color change, ion migration to dentine, radiopacity, setting time, ISO 6876:2012 linear flow, volumetric lateral flow and central filling of simulated grooves scanned using micro-computed tomography (µCT), pH, calcium release, volumetric change using µCT, chemical characterisation, cytotoxicity, and antimicrobial activity were assessed. Addition of 5% ZnO to Grey-MTAFlow and a bismuth-containing experimental composition were comparatively tested. Statistical analyses used Shapiro-Wilk, T-test, ANOVA, and Kolmogorov-Smirnov (p<0.05). Results The addition of ZnO to Grey-MTAFlow prevented dentine darkening after 90 days due to bismuth migration reduction, although no statistical difference was found (p=0.863). ZnO addition significantly enhanced Grey-MTAFlow radiopacity without differences in initial setting time. Grey-MTAFlow presented an ISO linear flow of 10.9 mm and a balanced volumetric lateral flow with central filling in µCT evaluation. All compositions presented an alkaline pH after immersion. Grey-MTAFlow had a significantly higher calcium ion release after 28 days in comparison to 24 hours (p=0.011) and volumetric expansion of 0.4±1.8% after immersion. ZnO addition altered the hydrated cement matrix once calcium hydroxide (portlandite) could not be detected in characterisation. Neither of the materials produced inhibition halos nor reduced bacterial turbidity, but all presented cytocompatibility above 100%. Conclusion Grey-MTAFlow expanded after immersion and exhibited higher luminosity values after the evaluation period when ZnO was added, but chemical modifications after this addition occurred.

Treatment outcomes of pulp revascularization in traumatized immature teeth using calcium hydroxide and 2% chlorhexidine gel as intracanal medication.

OBJECTIVE: Pulp revascularization is an effective treatment for immature necrotic teeth. Calcium hydroxide has been used in pulp revascularization as an intracanal medication due to its antimicrobial action and the non-exhibition of crown discoloration and cytotoxicity for stem cells from the apical papilla. Our study aimed to investigate the clinical success and quantitative radiographic changes of root development in immature traumatized teeth using calcium hydroxide plus 2% chlorhexidine gel as intracanal medication. METHODOLOGY: In this retrospective study, 16 patients were treated with a standardized pulp revascularization protocol. Calcium hydroxide and 2% chlorhexidine gel were manipulated in a 1:1 (v/v) ratio and inserted into root canals with Lentulo spirals (Dentsply Maillefer, Baillaigues, Switzerland). Patients were followed up for a period from 9 to 36 months for the evaluation of clinical and radiological data. Radiographic measurements of root length, root width, apical diameter, and MTA placement from the apex were quantified using software ImageJ. Wilcoxon test and t-test were used, according to nonparametric or parametric data, respectively, for changes over time in root length, root width, and apical diameter. RESULTS: Fifteen teeth survived during the follow-up period (93.75%) and met the criteria for clinical success. Although the changes seem to be very small in many cases, significant increases in the average root length (14.28%, p<0.0001), root width (8.12%, p=0.0196), and decrease in apical diameter (48.37%, p=0.0007) were observed. MTA placement from the apex and age at the time of treatment was not significantly associated with the quantitative radiographic outcomes. CONCLUSIONS: Pulp revascularization in traumatized immature teeth treated with calcium hydroxide plus 2% chlorhexidine gel as intracanal medication had high success and survival rates, showing periodontal healing and resolution of signs and symptoms. However, concerning the continued root development, the outcomes can still be considered unpredictable.

Effect of intracanal medications on the interfacial properties of reparative cements.

OBJECTIVES: The purpose of the present study was to evaluate the effect of calcium hydroxide with 2% chlorhexidine gel (HCX) or distilled water (HCA) compared to triple antibiotic paste (TAP) on push-out bond strength and the cement/dentin interface in canals sealed with White MTA Angelus (WMTA) or Biodentine (BD). MATERIALS AND METHODS: A total of 70 extracted human lower premolars were endodontically prepared and randomly divided into 4 groups according to the intracanal medication, as follows: group 1, HCX; group 2, TAP; group 3, HCA; and group 4, control (without intracanal medication). After 7 days, the medications were removed and the cervical third of the specimens was sectioned into five 1-mm sections. The sections were then sealed with WMTA or BD as a reparative material. After 7 days in 100% humidity, a push-out bond strength test was performed. Elemental analysis was performed at the interface, using energy-dispersive spectroscopy. The data were statistically analyzed using analysis of variance and the Tukey test (p < 0.05). RESULTS: BD presented a higher bond strength than WMTA (p < 0.05). BD or WMTA in canals treated with calcium hydroxide intracanal medications had the highest bond strength values, with a statistically significant difference compared to TAP in the WMTA group (p < 0.05). There were small amounts of phosphorus in samples exposed to triple antibiotic paste, regardless of the coronal sealing. CONCLUSIONS: The use of intracanal medications did not affect the bond strength of WMTA and BD, except when TAP was used with WMTA.

Prevalence and reasons for referrals to the Endodontics Specialty Clinic at the Piracicaba Dental School

Abstract Dental referrals to the Endodontics Specialty Clinic (ESC) are routine owing to the complexity of endodontic treatments. To obtain a better prognosis for treatment, students/dentists must perceive their technical limits. This study sought to investigate the referrals of patients to the ESC from different clinics of the Piracicaba Dental School, State University of Campinas - SP, Brazil, and check: a) the demographic profile of patients and the most commonly affected tooth; b) the clinic with the largest number of referrals; c) the reasons for referrals; d) the complexity of the cases; e) and the difficulty in assessing the referred cases based on the classification provided by the American Association of Endodontists (AAE) and Souza-Filho. The study sample consisted of patients' electronic dental referral records from February 2015 to June 2019. A total of 1,707 patients were referred to the ESC during the study period, and 62.4% were female. Lower molars were the most frequently involved teeth (34.8%), and 60.7% of the cases were referred due to the presence of root curvature. The AAE classification showed prevalence of highly difficult cases (71.3%), whereas Souza-Filho classification demonstrated a high rate of class III cases (85.8%). This study highlights the difficulties encountered by undergraduate students before or during endodontic treatments, reinforcing the need for clear criteria for selecting cases appropriate for each education level, thus improving endodontic treatment prognosis.

Tricalcium silicate-based cements: properties and modifications.

Mineral trioxide aggregate (MTA) has been widely used for different reparative procedures in endodontics. The extensive use of this cement for pulp capping, apexifications, apical surgeries, and revascularization is related to its ability to induce tissue repair and to stimulate mineralization. Several research studies have tested modifications in the composition of MTA-based cements in order to enhance their clinical performance. Novel formulations have been introduced in the market with the aim of increasing flowability. Important properties such as appropriate radiopacity and setting time, color stability, alkaline pH, release of calcium ions, and biocompatibility have to be considered in these new formulations. The latest research studies on the physical, chemical, and biological properties of tricalcium silicate-based cements are discussed in this critical review.

Effect of ultrasonic agitation on push-out bond strength and adaptation of root-end filling materials.

OBJECTIVES: This study evaluated the effect of ultrasonic agitation of mineral trioxide aggregate (MTA), calcium silicate-based cement (CSC), and Sealer 26 (S26) on adaptation at the cement/dentin interface and push-out bond strength. MATERIALS AND METHODS: Sixty maxillary canines were divided into 6 groups (n = 10): MTA, S26, and CSC, with or without ultrasonic activation (US). After obturation, the apical portions of the teeth were sectioned, and retrograde cavities were prepared and filled with cement by hand condensation. In the US groups, the cement was activated for 60 seconds: 30 seconds in the mesio-distal direction and 30 seconds in the buccal-lingual direction, using a mini Irrisonic insert coupled with the ultrasound transducer. After the materials set, 1.5-mm thick sections were obtained from the apexes. The presence of gaps and the bond between cement and dentin were analyzed using low-vacuum scanning electron microscopy. Push-out bond strength was measured using a universal testing machine. RESULTS: Ultrasonic agitation increased the interfacial adaptation of the cements. The S26 US group showed a higher adaptation value than MTA (p < 0.05). US improved the push-out bond strength for all the cements (p < 0.05). CONCLUSIONS: The US of retrograde filling cements enhanced the bond to the dentin wall of the root-end filling materials tested.

Zinc Oxide Inhibits Dental Discoloration Caused by White Mineral Trioxide Aggregate Angelus.

INTRODUCTION: The aim of the study was to investigate the addition of variable amounts of zinc oxide to inhibit dental discoloration caused by mineral trioxide aggregate (MTA) Angelus. METHODS: MTA Angelus and MTA with additions of 5%, 15%, and 45% zinc oxide (ZnO) in weight were tested. The set cements were characterized by using a combination of scanning electron microscopy, energy dispersive spectroscopy, and x-ray diffraction. Radiopacity and setting time were analyzed according to American National Standards Institute/American Dental Association (57/2012) and American Society for Testing and Materials (C266-08). Volume change was evaluated by using micro-computed tomography analysis. The pH and calcium ion release were measured after 3 hours, 24 hours, and 28 days. Dental discoloration in contact with the cements was measured after 24 hours, 28 days, and 90 days. Biocompatibility to subcutaneous implantation in rats was verified after 30 and 60 days. RESULTS: Addition of ZnO did not alter significantly the radiopacity, setting time, volume change, pH, and biocompatibility compared with MTA Angelus (P > .05). Calcium ion release increased with addition of ZnO (P < .05). Proportions of 15% and 45% ZnO interfered in hydration. The 5% ZnO addition was sufficient to prevent the dental discoloration observed with MTA Angelus. CONCLUSIONS: The addition of 5%, 15%, or 45% zinc oxide to MTA Angelus inhibits dental discoloration without modifying the radiopacity, setting time, volume change, pH, and biocompatibility.

Influence of working length and anatomical complexities on the apical root canal filling: a nano-CT study

Abstract The present study aimed to compare the filled volume by gutta-percha and sealer in the apical region of the main canal and ramifications, after instrumentation at two different working lengths using nano-computed tomography (nano-CT). Twenty-two premolars with apical ramifications were selected after micro-computed tomography evaluation and were randomly divided into groups for further endodontic instrumentation at two different working lengths: G1 - Root canals shaped 1 mm short of the apical foramen (n=11), and G2 - Root canals shaped at the apical foramen (n=11). After completing root treatment, nano-CT images were acquired, and the filled volume by gutta-percha and sealer in the main canal apical 0-4 mm and 0-1 mm ranges, and apical ramifications were objectively measured by an operator specialized in both radiology and endodontics, blinded for both groups. The Mann-Whitney test was applied to compare both groups regarding the filling of the main canal apical ranges and apical ramifications with a significance level of 5% (α ≤ 0.05). It was observed that root canals shaped at the apical foramen had a larger volume of the main canal filled than root canals shaped 1 mm short of the apical foramen, at both apical ranges (0-4 and 0-1 mm) (p<0.05). Regarding the filling of the apical ramifications, there was no significant difference between groups (p>0.05). In conclusion, the root canals shaped at apical foramen exhibited increased filling volume of the main canal in the apical region. However, neither of both working lengths influenced filling of the apical ramifications.

Resumo O presente estudo teve como objetivo comparar o volume preenchido por guta-percha e cimento na região apical do canal principal e ramificações, após instrumentação em dois comprimentos de trabalho diferentes, por meio de nano tomografia computadorizada (nano-TC). Vinte e dois pré-molares com ramificações apicais foram selecionados após avaliação por micro-tomografia computadorizada e foram divididos aleatoriamente em grupos para posterior instrumentação endodôntica em dois comprimentos de trabalho diferentes: G1 - Canais radiculares instrumentados 1 mm aquém do forame apical (n = 11) e G2 - Canais radiculares instrumentados até o forame apical (n = 11). Após a obturação dos canais radiculares, imagens de nano-CT foram adquiridas, e o volume preenchido por guta-percha e cimento nas faixas apicais de 0-4 mm e 0-1 mm do canal principal, e ramificações apicais, foram avaliadas objetivamente por um especialista em radiologia e endodontia, cego para ambos os grupos. O teste de Mann-Whitney foi aplicado para comparar os dois grupos quanto ao preenchimento das faixas apicais do canal principal e ramificações com nível de significância de 5% (α ≤ 0,05). Observou-se que canais radiculares instrumentados até o forame apical apresentaram maior volume do canal principal preenchido do que canais radiculares instrumentados 1 mm aquém do forame apical, em ambas as faixas apicais (0-4 e 0-1 mm) (p <0,05) Em relação ao preenchimento das ramificações apicais, não houve diferença significativa entre os grupos (p> 0,05). Em conclusão, os canais radiculares instrumentados até o forame apical mostraram um maior volume de preenchimento na região apical do canal principal. No entanto, os dois diferentes comprimentos de trabalho não influenciaram o preenchimento das ramificações apicais.